GDB uses the vRun packet if available to restart a running process in
extended remote mode. Support this like the R packet and set the
semihosting command-line to allow it to be specified from GDB.
Change-Id: I9cb812b22170630f782113c9927e46e0cd5b1f0f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5186
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
As it is mentioned here [1] type's ID is unique name within containing feature.
That said if regs of the same type located in different features it's required
to insert type definition at least in each feature.
See more details in discussion here [2].
[1] https://sourceware.org/gdb/onlinedocs/gdb/Target-Description-Format.html#Types
[2] 2a5f5125ac (r33460077)
Change-Id: Id92b061cfbf47d5c032a02c2c406b28affd0b02a
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5179
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Armv7a is able to read and write memory at un-aligned address, but
only when bit SCTLR.A (Alignment check enable) is zero and the
address belongs to a memory space with attribute "Normal" (see [1]
chapter A3.2.1 "Unaligned data access"). In all the other cases
the memory access will trigger an alignment fault data abort
exception.
Memory attributes are explained in [1] chapter A3.5 "Memory types
and attributes and the memory order model".
Disabling the MMU cause a change in memory attribute, as explained
in [1] chapter B3.2 "The effects of disabling MMUs on VMSA
behavior".
This can cause several issues. e.g. a SW breakpoint on un-aligned
4-byte Thumb instruction, set when MMU is on, can be impossible to
remove when MMU turns off.
While is possible to check all the possible conditions before an
un-aligned memory access, it's clearly more maintainable to skip
such complexity and only perform aligned accesses.
Check the alignment and eventually modify the data size before
calling the functions cortex_a_{read,write}_cpu_memory_slow().
Change the comment in the two functions above to comply with the
new behaviour.
[1] ARM DDI 0406C.d - "ARM Architecture Reference Manual, ARMv7-A
and ARMv7-R edition"
Change-Id: I57b4c11e7fa7e78aaaaee4406a5734b48db740ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5138
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Issue has been found when I tried to read 64 MiB QSPI flash bank.
Bank is memory mapped, default_flash_read() is used for 'flash read_bank'
command. OpenOCD consumed as much as 6.8 GiB of RAM during this
process. Investigation showed that this happens because JTAG queue
is not limited in any way. OpenOCD queues 16 millions of AP reads
allocating all corresponding data structures.
Most of this memory is allocated in:
cmd_queue_alloc (commands.c) - 4.2 GiB
dap_cmd_new (adi_v5_jtag.c) - 2.25GiB
This patch implements a pool of "struct dap_cmd" objects using
linked list. Objects are taken from a pool in "dap_cmd_new()" and
returned to the pool when they are not needed. Size of the pool
is limited to 64K of objects, JTAG queue is forcibly executed
when this limit is reached.
Checked with Valgrind and Clang analyzer - no new warnings.
Change-Id: I5aaaecce5ed71414f7965a2598f49742f6a6b2b5
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4948
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Make driver_priv point directly into the corresponding chip bank structure
and add a pointer to it to get back to its chip when it's needed. This
removes the need to keep track of any bank number, either global or chip-
local.
In addition, it simplifies the cases where the chip structure was just used
to access the chip bank fields; now they are directly accessible.
Change-Id: Iaa353cd4fa7d8ff94c2ef69028c7cb32fade0420
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/4775
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current code checks the count to determine whether to read bytes or
words. However it fails to consider whether the base address is suitably
aligned.
Instead use the target_read_buffer() function which is for exactly this
purpose and generates optimal accesses with natural alignment.
Change-Id: I32ab5417890ee2219902df1529bc220fe353b4c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3217
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The preverify option allows to check whether flashing is necessary.
If the target is flashed often/automatically this can save time and
preserve the flash. This is expecially helpful in CI environments.
Change-Id: Iead0a269e1a772b751d4dd9e8b53b2fecc874624
Signed-off-by: Moritz 'Morty' Strübe <moritz.struebe@redheads.de>
Reviewed-on: http://openocd.zylin.com/5292
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
I think that libusb_handle_events_timeout_completed is supposed to make
progress or time out, but sometimes we hit a case where it makes no
progress, and mpsse_flush() loops forever. This wall clock timeout
notifies the user that this is going on.
When I wrote this code, this bug would reproduce every hour or two, but
right now it's not happening for me.
Change-Id: I7eb66f43462298e263a48048aa0c8769095661eb
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4767
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the reference manual it should be 0x40000000. Flashing (and
booting) a firmware with this MSC base was successful.
Change-Id: I739e67d36555b8170a3b8e26f54cf1c09ce8424b
Signed-off-by: Christian Meusel <christian.meusel@posteo.de>
Reviewed-on: http://openocd.zylin.com/5263
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix expression "(pin_status | 0x4)" which was always true rather than
testing a bit. Untested - was clearly not expressing the intent of the
author by inspection. Found by automated tooling and rtrieu@google.com.
Signed-off-by: Seth LaForge <sethml@google.com>
Change-Id: I4bb91e60e8ce9757bf21976cc48de6f85a39c68d
Reviewed-on: http://openocd.zylin.com/5301
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The C standard says that errno is set to ERANGE if an out-of-range value
is returned by strtol, strtoul, et. al., but it does not say that errno
is cleared if the function is successful (and, indeed, it is not on
glibc). This means that, if errno is ERANGE before strtol is called, and
if the value to be converted is exactly the maximum (or, for a signed
conversion, the minimum) legal value, COMMAND_PARSE_NUMBER will
erroneously indicate that the value is out of range.
Change-Id: I8a8b50a815b408a38235968f1c1d70297ea1a6aa
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5298
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
PAGE_SIZE is defined in system includes on some systems, this would
avoid the unintended conflict
Fixes
| src/flash/nor/esirisc_flash.c:95:9: error: 'PAGE_SIZE' macro redefined [-Werror,-Wmacro-redefined]
| #define PAGE_SIZE 4096
| ^
| /mnt/a/yoe/build/tmp/work/core2-64-yoe-linux-musl/openocd/0.10+gitrAUTOINC+7ee618692f-r0/recipe-sysroot/usr/inclu
de/limits.h:89:9: note: previous definition is here
| #define PAGE_SIZE PAGESIZE
Change-Id: I195b303fc88a7c848ca4e55fd6ba893796df55cc
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Reviewed-on: http://openocd.zylin.com/5180
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is no sense in displaying the max size (2M) as there is variants
of this device with reduced flash size
Change-Id: I40574064d75fdf2a038044c81038a6d7abc6c4dd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5288
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added "exist=true" field to the reg_list struct to make access to the
dsp563xx registers again possible. Without it defaults to exist=false
and all the reg related functions will return nothing.
Fixes regression from b5964191f0
Change-Id: I9c256346735b8d66919c4ba83f528a8afca46ff9
Signed-off-by: Han Hartgers <han.hartgers@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5239
Tested-by: jenkins
Fix two expressions where precedence of operator | vs ?: was clearly confused.
Untested - was clearly not expressing the intent of the author by inspection.
Found by automated tooling and rtrieu@google.com.
Change-Id: I46f190154797f8affc761caf3a15a1a9db53d702
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/5281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
1. Add get_thread_reg() to rtos. It's used in rtos_get_gdb_reg() to read
the value of a single register, instead of reading all register values
by calling get_thread_reg_list().
2. Add set_reg() to rtos. gdb_server uses this to change a single
register value for a specific thread.
3. Add target_get_gdb_reg_list_noread() so it's possible for gdb to get
a list of registers without attempting to read their contents.
The clang static checker doesn't find any new problems with this change.
Change-Id: I77f792d1238cb015b91527ca8cb99593ccc8870e
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5114
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This is causing repeated build failures. Its design is so fundamentally
broken that if someone actually wants to use it, a full rewrite is the
only option. So it's not even worth deprecating in the hope that someone
will notice and fix it, just get rid of it.
Change-Id: I513069919a3873bd69253110f7fb6f622ee7d061
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5243
Tested-by: jenkins
Reviewed-by: Jeffrey Booher-Kaeding <Jeff.Booher-Kaeding@arm.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command "soft_reset_halt" is deprecated since mid 2013 with
the commit 146dfe3295 ("cortex_m: deprecate soft_reset_halt").
Nevertheless it is still extremely useful with multicore chips
where it allows to reset only one of the cores, option not
available through asserting the chip-wide srst.
Without a better replacement of the command, it's worth fixing it.
Accordingly to ARM DDI 0403E.d, chapter C1.4.1 "Entering Debug
state on leaving reset state", to halt the core at reset both bits
DHCSR.C_DEBUGEN and DEMCR.VC_CORERESET must be set.
Current code only sets the latter bit, relying on having C_DEBUGEN
already set through other commands, e.g. "halt". This prevents the
command "soft_reset_halt" to work if issued as very first command.
Set the bit C_DEBUGEN in command "soft_reset_halt".
Change-Id: I66bfd6a0da1fca5049dea037b4d258cf6f842966
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4987
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Thanks to command_run_linef() there is no need to pre-build the
command using alloc_printf().
Change-Id: Iccfebd6063d1ac162f090fe2309b1f51bebf0214
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5226
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The `command_run_line` function contains a comment saying it should be
reentrant. However, it isn’t: it NULLs out `current_target_override` and
doesn’t restore it before returning, and it changes the `context`
associated data of the `interp` object and then deletes that associated
data before returning rather than restoring it to its previous value.
Change-Id: I84fd46ef7173f08cf7c57b9a5b76e4986a60816f
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5223
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The AHB5-AP is implemented in Cortex-M23/33 based devices.
Change-Id: I505954a2e2c6462ce0aa96eba1d55b016c5028b9
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5232
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
This access port type comes with the AMBA 5 protocol specification,
see 'C1.3 AP' in ARM IHI 0031D.
Change-Id: I3c4f0a69230daaf4f5f979de6213fe3c025a089a
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
This patch adds ARMv8-M CPUs detection logic in ARMv7m target specific code.
Also adds a slightly different watchpoint manipulation logic for ARMv8-M.
This is based on ARMv8-M architecture reference manual.
Tested on ARM Musca A board.
Change-Id: I0652560954ef02c378a7067fab586edf39d3e9cc
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4997
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I1b917a4c1205115c4e0315373d81a9305e931258
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4944
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I32c43e2e47366363521fa3f387de9e2fb1c20852
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4943
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of jtag's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition.
It can be tested running openocd on a jtag target and adding a
jtag event "setup" with a single line "return", e.g.
openocd -f board/ti_cc3200_launchxl.cfg \
-c 'jtag configure cc32xx.cpu -event setup return'
to get the message:
../src/jtag/core.c:1599: Error:
in procedure 'jtag_init' called at file "../src/jtag/core.c",
line 1599
Modify jtag_tap_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I6d6febc15ef169638afffbffc1810e0b84fcf5c8
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5199
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of target's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition, thus dumping the
call-trace. The execution is not stopped because the error is not
further propagated, but the error message is annoying and
misleading.
It can be tested running
openocd -f ./test.cfg
using the following script "test.cfg". You can replace the board
file in line 1, to use a board available in your lab:
1 source [find board/st_nucleo_f4.cfg]
2 [target current] configure -event reset-start {}
3 [target current] configure -event reset-end {return}
4 init
5 proc a {} {[target current] invoke-event reset-start}
6 proc b {} {[target current] invoke-event reset-end}
7 proc c {} {a;b;echo "arrived at the end"}
8 c
9 shutdown
The execution produces:
./test.cfg:7: Error:
in procedure 'c' called at file "./test.cfg", line 8
in procedure 'b' called at file "./test.cfg", line 7
arrived at the end
that shows the call-trace but does not halt the execution.
The developer can avoid using the "return" command in the event
body by defining a TCL procedure that implements the handler and
that contains the "return" command, reducing the handler body to
a simple call to the procedure above. But this approach is either
not documented nor always intuitive while writing the handler,
causing waste of time to look for the false error.
Modify target_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I2b860bab7233c6ed13ee4098e348d7533e1c4626
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4974
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c2e18bfaea changed the size of the JTAG-to-SWD sequence
from 15 bytes to 17 bytes. This broke SWD switch sequence transfer
for buspirate, since buspirate packets can only hold a payload of up
to 16 bytes and we tried to fit the whole sequence in a single packet.
Splitting up the sequence transfer in appropriately sized packets
makes buspirate SWD work again (successfully tested with buspirate
firmwares v6.1 and v7.0).
Change-Id: Ib5b412b9e77287d705d2762e31c16d30318b50e3
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Reviewed-on: http://openocd.zylin.com/5200
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If1f56fd5d610b993a4ecbc900fac9f90638037c9
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5202
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit 877cec20dc
("command: check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The command '$_TARGET configure -xxx' was therefore applicable on running
OpenOCD to change the target configuration. It is handy e.g. for changing
an event handler or changes of the work area.
Change 'configure' command .mode to COMMAND_ANY to make it possible again.
The only parameter which cannot be re-configured after init is -gdb-port.
Test the command mode and refuse setting of gdb port after init.
Change-Id: I88493ac10a46647dc52a88fbc9f8ce6b5ba3bcd0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5214
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
since b5964191f0, all XScale-specific registers were missing, breaking
config scripts.
Change-Id: Ia56f3ca17500ba54bd08f417e9a5aaaa8a1be8c4
Signed-off-by: Michael Schwingen <spam-openocd@discworld.dascon.de>
Reviewed-on: http://openocd.zylin.com/5136
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro TARGET_ADDR_FMT, defined in helper/types.h, already
includes the prefix "0x" in front of the hexadecimal number,
being defined as:
#define TARGET_ADDR_FMT "0x%8.8" TARGET_PRIxADDR
An additional "0x" is present in mem_ap; it prints debug messages
with a double "0x" before the address:
Debug: 2921 34180 mem_ap.c:153 mem_ap_write_memory():
Writing memory at physical address 0x0x5000000c; size 4;
count 1
Remove the incorrect hexadecimal prefix.
Change-Id: I38f19ed2a2f542bd5df53e947a2604f1cbe80e08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5222
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
To support 128 bit registers, the rtos_reg structure value
array needs to be updated from 8 to 16 bytes.
Tested by reading ARMv8 NEON FP regs on an Ampere eMAG 8180 with GDB.
Change-Id: I7f3fe1a5b2def599d021787fbe9cdd51f92859a4
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5209
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The ARMv7-A architecture supports super sections which allows mapping
physical addresses up to 40-bit into a 32-bit virtual address using the
short descriptor format (see ARM DDI 0406C.c section B4.1.112 for
details).
Change-Id: I8e64d0e93e36ae7a7da7b7bf2a8342856bb044f1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5212
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In preparation for adding super section decoding, do not restrict
armv7a_mmu_translate_va_pa() to 32-bit virtual addresses since ARMv7-A
processors with VMSA extensions (including LPAE) can issue wider
physical addresses. Update casting to uint32_t where necessary.
Change-Id: Id1c3d0d5ac324cbdc334259d9ea75fe4981671a1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5211
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function is not used anywhere in the tree, remove it, such that we
only have a single function moving forward that might need to deal with
short vs. long format specifics.
Change-Id: I80e81cd7eba1e028d1afaeaedb675b46c0ca6fa1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Check earlier that the read of the PAR register was successful instead
of starting the decoding and then checking for an error reading that
register.
Change-Id: Id96c2b2f76d2d1c745fcfa55ad4c1e6db92106f9
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
armv7m_get_core_reg() calls arm->read_core_reg()
arm->read_core_reg() expects the register number as an index
to core reglist, not an ARMv7M specific register code.
Use reg->number instead of armv7m_reg->num.
The change solves assert
src/target/armv7m.c:222: armv7m_read_core_reg: Assertion
`num < (int)armv7m->arm.core_cache->num_regs' failed.
when gdb 'info reg' is issued on a Cortex-M target and
no cortex_m_debug_entry() has been called since OpenOCD start
(target was halted before OpenOCD start).
Change-Id: I32a2294693ef979b613be93aeceb3b0eb06ee6df
Ticket: https://sourceforge.net/p/openocd/tickets/216/
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For legacy support, drivers that do not define a list of
transports get identified as jtag_only.
Cleanup this old crust and initialize properly the transports
field in the jtag_interface for all the drivers.
Change-Id: I9c86064e5d05bd0212bc18f4424414e615e617fe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In the initial commit 6c9b804d61
in 2007's svn://svn.berlios.de/openocd/trunk@246
a target script gdb_program_config was called before gdb flash
programming. To guarantee the script does not left any pending
command in the jtag queue, a call to jtag_execute_queue() was
inserted after the execution of the script.
In following commit ef1cfb2394
in 2008's svn://svn.berlios.de/openocd/trunk@975
the script was replaced by the event "old-gdb_program_config" and
the call to jtag_execute_queue() get executed in every case, even
if the event handler was not present.
At last, commit bb3793c9a4
("target: remove legacy target events") stripped away the
obsolete event but left the call to jtag_execute_queue(), now
completely useless.
Remove the call to jtag_execute_queue() and clean-up the code
around it.
Change-Id: I284f54d656d431ad6cdc25ca18218c09db31bd25
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4911
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since the first commit 09883194f8 that introduced cortex_m, the
code has a delay of 50ms after srst has been asserted.
The specific delay is implemented through the JTAG_SLEEP command
sent in the jtag queue.
To remove the dependency from the jtag queue, replace the delay
with a transport independent function.
In case of jtag transport, this change keeps the same behaviour
only if the jtag queue has been flushed before the delay. This
does not happen if the call to dap_dp_init(), few lines above,
fails while calling a dap_queue_dp_{read,write}(); in this case
the jtag queue will be flushed later, after the delay, while in
the original code the delay would follow the flushing of the
commands already queued. Anyway, this different behavior would
only happen in case of DAP already not responsive so anticipating
the delay in such error condition is not supposed to add further
problems.
Change-Id: If15978246764e4266b10e707d86c03e5ed907de7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4912
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is just a single entry point for the jtag API .khz(),
.speed_div(), .power_dropout(), .srst_asserted().
Simplify the code by in-lining the default handler.
The overall code behaviour is not changed.
This change prevents modifying at run-time the content of
struct jtag_interface.
Inspired from change http://openocd.zylin.com/943
by Evan Hunter <ehunter@broadcom.com>
Change-Id: I09aeb76d614db57b1884ac7ee9f00c152cd77849
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4892
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The specific SWD API to change/query the adapter speed is never
called because the equivalent JTAG API is used in place of it.
In the restructure of struct jtag_interface, the JTAG API is
promoted as global adapter API, thus a specific SWD one is not
anymore required.
Change-Id: I1e810d255b4dfcd5791b4fac8ae1260c31a057fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4891
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently size of the GDB buffer is 16384 bytes but it is treated as
nul-terminated string in most of the code, so effective size of the
buffer is actually 16383 bytes. OpenOCD responds with `PacketSize=3fff`
to qSupported request. Result of GDB's `m` command is encoded in hex so
each data byte uses two bytes in the buffer. As a result GDB will split
bulk read requests into chunks 0x1fff bytes each. This causes troubles
on targets (or memory regions) which support only aligned, word-sized
access (such as MMIO buffers).
Steps to reproduce (psoc6 target):
gdb> dump binary memory dump.bin 0x040320000 (0x040320000 + 65536)
OpenOCD:
Error: Failed to read memory at 0x40321ffe
Error: Failed to read memory at 0x40321000
Error: Failed to read memory at 0x40323000
Error: Failed to read memory at 0x40325ffe
Error: Failed to read memory at 0x40329ffa
Error: Failed to read memory at 0x40329ffc
Error: Failed to read memory at 0x4032bffc
Error: Failed to read memory at 0x4032dffa
Consolidate GDB_BUFFER_SIZE usage: ensure size of each buffer is
(GDB_BUFFER_SIZE + 1), add explicit comment that additional byte is used
for nul-termination. Report correct size of the buffer to GDB (0x4000)
as recommended in GDB's docummentation: `if the stub stores packets in a
NUL-terminated format, it should allow an extra byte in its buffer for
the NUL`
Checked with clang-asan, clang-analyzer, valgrind - no new errors.
Change-Id: I909e8a2c6b010c5d4a304641808d4a807a4ec18d
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/5109
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The warning appears for every possible device during enumeration
and provides no useful information for an end-user.
Change-Id: I56e7889a5d9d4656de13ad9e21be3a6e1906e05f
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The implementation-defined bits have different semantics for each bus
and different recommended defaults.
Change-Id: I562fe24643bb1f3abc696339e382a75ccf2f2873
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a copy of handle_md_output() from src/target/dsp563xx.c
Change-Id: Iadd003fd1dcdbc7990d46a58ee2e7c30826ac6af
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5175
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By definition the EXTERNAL bit in Debug Fault Status Register indicates
that an external debug request (EDBGRQ) signal was asserted.
Usage example: this could be done by CTI in multicore devices in order to
halt all the cores together.
Change-Id: I7830455ce5da6702b7d08c8fa7bfe80e4d8a5055
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5157
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 89fa493a3b removes the top
level command "unknown" and adds in command_unknown() some unclear
code that should detect a user-implemented "unknown" command.
But, all the commands that trigger the execution of the function
command_unknown() are registered in register_command_handler() and
have the command name prefixed with "ocd_".
Due to such "ocd_" prefix in cmd_name, the condition
if (strcmp(cmd_name, "unknown") == 0) { ... }
is always false.
Nobody complained for almost 10 years so we can proceed to remove
this dead code, before merging any change that obsoletes the
prefix "ocd_" and potentially makes the condition true.
Remove the dead code guarded by the condition above.
Change-Id: Icf11a956bb2d68fc84e6eb5779edf8e35db8fa53
Fixes: 89fa493a3b ("remove unknown handler")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Left unused after commit "target: unify memory read/write
commands", can be removed.
Change-Id: Iea6ef9204c8071283a66a679b3d6edbb0c929c5c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5153
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In case of error, a command should use command_print() to report
the error message, so it get printed only on the session that run
the command itself, and the message can be intercepted with the
tcl command catch if it has to be handled differently.
Current code drops the command output when the command returns
error, claiming that it's the command that *should* have printed
it already. This is true only if we *abuse* of the LOG functions,
but accepting the side issue of having the LOG printed in every
session and being unable to catch{} the error message.
Since we have switched to command_print(), change the code to
propagate the command output also in case of error.
Change-Id: I95de424a65e63702bdb3b2277749a0ac6aaaa503
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5178
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Two calls to command_print() in imx_gpio fixed - the first parameter
adjusted (CMD_CTX -> CMD) per the changes from this commit:
6cb5ba6f11
Change-Id: I6cb0909439a632d3109edfc68070b9b561f86d49
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5176
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The commit 84ca4995ad ("drivers/bcm2835gpio: fix usage messages")
has been merged before commit 6cb5ba6f11 ("helper/command: change
prototype of command_print/command_print_sameline") introducing two
new call to command_print() that were not modified by the second
commit.
This triggers a compile error on ARM host.
Fix the incorrect function call.
Change-Id: I2736bae24141685b7590fd6b4aa5e6a29b2cab29
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5174
Tested-by: jenkins
In jtag_vpi_stableclocks() the TMS line needs to be set properly
based on the current JTAG TAP state (TMS=1 in TAP_RESET state vs.
TMS=0 in other cases).
Change-Id: Id49622ba83015f97b61b6a896edde4448f1fbdc6
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5151
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Prevent the State Machine from moving at the end
of several cycles during run_test_idle
state.
Change-Id: Iabdf90a58334dd3d0e6e34b02983a85662062825
Signed-off-by: Megan Wachs <megan@sifive.com>
Reviewed-on: http://openocd.zylin.com/3635
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The commit "helper/command: do not replace new commands with
ocd_ prefix" breaks the print of usage text when a multi-word
command is typed incompletely.
Fix it by explicitly running the "usage" command.
Change-Id: I46f8e521d9b6ac617bff8938cf8fc96f0ade45c8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5166
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When opening multiple telnet connections, the command output on
one console is broadcast to all the other console.
Send the command output only to the output handler that has been
set for that context.
For the moment, still broadcast the errors.
Note that contexts which doesn't explicitly set the output handler
(e.g. gdb_server), will inherit the global output handler
configuration_output_handler() that will broadcast the output.
Change-Id: I1f2d6e6a3bbf730f5fa77246730fce1445742a1e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5093
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Part of the output is generated with log functions.
Change prototype of find_target() and use command_print() for all
the output of the command.
Change-Id: Ia9fdb653fd5b27be427381053a037545faa34414
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5092
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
We do not register commands with special "ocd_" prefix anymore.
Change-Id: I588816eb22c2435a97be5fbfa87ee5584274b02f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5087
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Once the wrapper "ocd_bouncer" is removed (which was the only user
of this command), there is no reason to keep the command any
longer.
Remove it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I979ce1c147babedb44dd77418751133f589f827c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5084
Tested-by: jenkins
The TCL return values are now consistent, no need anymore for the
hack of registering the commands with "ocd_" prefix and override
them with proc ocd_bouncer.
Clean-up the command registration and remove the proc ocd_bouncer.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I2a467e73ecb068686ea3fda91bf961aba6db6427
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5086
Tested-by: jenkins
Command's output should be put in JimTcl result.
We should not anymore capture the log output and pack it as a
JimTcl result.
Remove the log capture feature in script_command_run().
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Id326c8719e1cee9156d7fc15ae8355ec79a74951
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5085
Tested-by: jenkins
Rationale:
1. There's logging output and there're return values;
2. If a function should return something, it should do it explicitly,
same for logging;
3. Interactive interfaces (telnet, Gdb and Tcl RPC) must always return
the result of the evaluation for the given expression. You can
suppress this output by adding ``; after 0'' to the end of your
expression.
4. Some commands "throw an exception" and if you want to be able to
collect both the return value (when it succeeds) and the log output
(when something goes wrong) you can use do like this:
set log_output [capture "catch {reset_config} return_value"]
So what I'm proposing is following:
1. Every jim_handler command should set the return value the standard
JimTcl way, without any tricks. If it needs to print some logging
output, it should use LOG_* functions.
2. The usual commands (COMMANDS) can easily construct their return
value by appending strings with command_print() and
command_print_sameline(). This required changing "struct
command_invocation" and passing a pointer to it to command_print*
functions.
The code is already functional, please test and comment.
TODO items:
1. Modify all jim_handler commands to properly return or log values
(some of them are commented out for now in this patch).
2. Properly document "capture" command and provide a convenience
function to automate log_output + return_value gathering.
3. Add appropriate Doxygen comments.
4. Add Tcl RPC interface description to the manual, all the example
clients in different languages (from the mailing list) to contrib/.
This change is the core part of http://openocd.zylin.com/1815 from
Paul Fertser. It has been extracted and rebased to simplify the
review and provided again as 1815.
Change-Id: I675c91aa9da1e4e7c6f0a8fe6112a00550b9e4db
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/1815
Tested-by: jenkins
The command uses LOG_USER() instead of command_print().
Fix it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I92e5e5954a75b96093b3ed6af73a7536c063b639
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5083
Tested-by: jenkins
After replace CMD_CTX with CMD, the indentation is incorrect.
Fix it.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5d7c40227ceda2e9db8dab88088d74012d2254c4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5082
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of show_config*() functions to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I131a904774bf60ad1bf9d90dbc65927c246ac23a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5080
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_dump*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia43bff112372cbb76e1aea9f59f4a9b6df05c15d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5079
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_analyze*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ie7cfd323fe591a987ea648a20be2bb9c7273dde8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5078
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of binprint() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5ebdc50417d97c791c98ac0cfe2218319809eb7f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5077
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_set() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: If00f9cfb784b53bb3df92d4469178e2f930a146a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5076
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_list() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibff636d476bcd59784ce3da5409d930225cfe637
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5075
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I2150201fad3fd3bc0be89249dcbd314b38a6f860
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5074
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of dap_rom_display() and dap_info_command() to
pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Idb97b20759c03fcecbac1184c354966f469caa5f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5073
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of etmv1_analyze_trace() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic923af5480a54c7272d2ff1abbe235ba941cf1a0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5072
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_iod_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I67f594c80d6bbbbf6c9567069a545f16877b1e94
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5071
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm7a_handle_l2x_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib926cd7380ac8b6fb89f64e0a85d81d124633315
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5070
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv7a_handle_cache_info_command() to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I27f507869cb41c74722a759e69dfd45658fcd4be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5069
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv4_5_handle_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib6ab3ec2fc6504c2a0635b654697a4b6e12a3750
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5068
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib0b84c933689ac8c940c9bbe62d9c95fd015c4f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5067
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of display_cache_info(),
armv8_handle_inner_cache_info_command() and
armv8_handle_cache_info_command() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I13519c79af82cdba57d5205ba84a5a27fce65a36
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5066
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of xscale_display_instruction() and of
xscale_analyze_trace() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I8420f19c1b2ff0d2a2f2a8d3627767f7acda437c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5065
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of xscale_verify_pointer() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Id047fab41ec4f673a46756b0ab901e659e088544
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5064
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of mips_m4k_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I9fa3e883d2ca9cc858caaefd33586f78638702f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5063
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of mips32_verify_pointer() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic4a4de10518ee009d6df420e7278fd028e1f22ca
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5062
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of cortex_m_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Icf6d1e5f8b4a3ce115c4253e49769df19a5211ae
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5061
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm946e_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib7119e2b009d05eec47b50c3b9d32feaebc97538
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5060
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm720t_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I7fa0628fabacd9ceb62ce921192f88edca659c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5059
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm966e_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I92745591256ad56a588b6386842028e0b18dec96
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5058
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm926ejs_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibbb03429a7fe8b9979f9bb9e513f9eb86aee3b5b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5057
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm920t_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I9a603d7c032df91b3913aadb242de89dbed0358e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5056
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of get_current_sam4() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I8dfa66f3f6be318d6ba89649279b1b4502f375d9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5055
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of get_current_sam3() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia1e7af79d0fc89d229b4e10df37317a374bbab62
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5054
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Pass CMD instead of CMD_CTX as parameter to nand_list_walker().
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia11887dfc6dc58d5458a88ba84780cd895b8c253
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5053
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of nand_fileio_start() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I7993f6aba997a2d2917949563651c8d0c213730d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5052
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
When dumping traces or semihosting text, the command that enabled
it is already completed, so CMD is not a valid value.
Plus, we want the dump to be printed in the command context where
the enable command was executed.
Replace command_print() with command_output_text().
Change-Id: I297a2b799a914233499641062407cf6e8b9fe012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5051
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Current code provides two independent implementations for the
memory read/write commands:
a) jim_target_md()/jim_target_mw() for the target specific
commands "<target> m[dw][bhw]"
b) handle_md_command()/handle_mw_command() for the current target
commands "m[dw][bhwd]"
The case a) misses the handling of doubleword and calls functions
command_print_sameline() with first parameter NULL because defined
as jim handler.
Remove the code in jim_target_md()/jim_target_mw() and use the
same code in b) for the target specific memory read/write.
This approach also provides support for 64-bit data size, not
present in the implementation in a).
The only drawback is that the implementation of memory read in b)
prints the data also as human readable ASCII characters, feature
missing in the implementation in a). This could introduced later
if it's really needed.
Update the documentation to:
- add 64-bit support
- add phys parameter
- add the count parameter
Add attribute "unused" to target_buffer_get_u8(), now not used
anymore.
Change-Id: Ib11ff924c409ad87e77fe708d628b2cc82b74d6a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5050
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Events are supposed to be executed asynchronously and not linked
with any command, so it's incorrect printing out an eventual error
using command_print().
Even in the case of events triggered by the command
<target> invoke-event <event-name>
the eventual error in the event handler is not propagated to the
command, so the command_print() is still not appropriate.
Replace command_print() with LOG_USER() in target_handle_event().
Add further info in the log to identify which event has generated
the error and its associated target.
Before return, clean-up the error message and the stacktrace from
the error already displayed, to avoid propagate them.
Change-Id: I5966aa25e7c81348f4ad4d6e7ce5d4dee44ea4c8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5049
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of target_process_reset() to pass CMD instead of
CMD_CTX.
Replace NULL parameter of command_print().
Remove extra newline, already added by command_print().
Change-Id: Ieb820c2586e1ff74a0c2b63a9c8693ca7710dfb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5048
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Accessing the variable "cmd" in a COMMAND_HANDLER is confusing
because the variable definition is not visible in the prototype,
thus "cmd" can be identified by the reader as a global variable
defined somewhere else.
Add the new macro CMD to make more evident it is a part of the
COMMAND_HANDLER.
Change-Id: I8f63da593a931045cc404323f143b88c5c80ab5e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5047
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
jim_arm946e_cp15() used command_print() in the jim handler.
Change-Id: I0a258aad5a60f45672b9b6fa6819691507d4f0f6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5000
Tested-by: jenkins
jim_target_event_list handler used command_print() in jim handler.
Rewriting the jim handler to the OpenOCD command is easy
as get_current_target() returns proper target for prefixed commands since
bb9d9c6026
Change-Id: I3e937249386ca5dbd7a5dd6ebb0ccde0911325d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4993
Tested-by: jenkins
Change-Id: I5dc16031c38576d853774b6123c93be1e1b4aa96
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5133
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Based on RM0433.rev5 > Section 3.3.9 : Flash program operations:
QW1/2: this bit indicates that a write, erase or option byte change
operation is pending in the write queue or command queue buffer.
It remains high until the write operation is complete.
It supersedes the BSY1/2 status bit.
On this basis, stm32x_wait_status_busy is renamed accordingly to be
'stm32x_wait_flash_op_queue'
Note : In this commit there is a fix of SR_ERROR_MASK value in flash loader algo
Note : This modification is mandatory for revision X, and backward compatible
with old revisions
Change-Id: I59d2973317d76b01fbb0fb5e4a472a47d0a7a5b5
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4883
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We have the function to wait for bits in dscr. Use it whenever
possible.
When the bit to test is DSCR_INSTR_COMP, use instead the wrapper
function cortex_a_wait_instrcmpl().
Change-Id: I5c54c239a00f489712af448eb97752210b4b38b8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In function cortex_a_wait_dscr_bits() the last read on dscr gets
ignored in case of timeout, even if it finally provides the value
that would trigger a successful return.
Check the returned value before testing the timeout.
Also, print a message on failure reading dscr.
Change-Id: I261ac1545113db39374833a55be911a4da71d893
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5112
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Depending on adapter speed, the function cortex_a_poll() can take
time to execute and can complete successfully when the timeout is
already expired. Checking the timeout at function return causes a
timeout error while that could be avoided.
Check the target status at cortex_a_poll() return, before checking
for the timeout.
Change-Id: I4c1581f6e718298c566df7b1359255e16e3955d5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5111
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
`maskisr steponly` disables interrupts during single-stepping but
enables them during normal execution. This can be used as a partial
workaround for 702596 erratum in Cortex-M7 r0p1. See "Cortex-M7 (AT610)
and Cortex-M7 with FPU (AT611) Software Developer Errata Notice" from
ARM for further details.
Change-Id: I797a14e4d43f6dcb3706528ee4ab452846ebf133
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4673
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The modified lines cause "runtime error: left shift of <X> by <Y>
places cannot be represented in type 'int'", because integer
literal is cast to int by default.
Change-Id: Ie38119b5eb46ee470e0d149959e523b48ac4d66d
Signed-off-by: Mete Balci <metebalci@gmail.com>
Reviewed-on: http://openocd.zylin.com/5005
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with SiFive HiFive1 development board.
Change-Id: I96a9a528057fcf9fc54d3da46a672d2cd54c3d5f
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4885
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Bit 29 of OPTSR is IO_HSLV. It ought to be read in stm32x_read_options
and written in stm32x_write_options. Adjust the bitmasks to do this.
Change-Id: I785a5291c991c98b774177f960dc58f2b5e045e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4745
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Every command has been fixed with proper usage field.
Change LOG_DEBUG with LOG_ERROR so a developer will get a visible
alert for missing usage field when adds a new command.
Change-Id: I077c3745fd6265aded8e54b3f9d202d4d6516966
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5026
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This can be used to dynamically distinguish between similar chips in tcl
code.
Change-Id: Ic4dfb61693e78616355173142dc7f9b9683a9f73
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5033
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Command should return target->coreid, not target->working_area_size
Solution appeared as an off topic fix in http://openocd.zylin.com/4935
Change-Id: Ic9701ce2001c75060dbaa75fbd013ed475a352e5
Suggested-by: Graham Sanderson <graham.sanderson@gmail.com>
Reported-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5035
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
By using the command "add_help_text" to add a help text to a TCL
procedure it implicitly creates a new command_registration struct
that has field .usage set to NULL. This triggers a debug message
BUG: command '%s' does not have the '.usage' field filled out
Use an empty string if usage field is NULL.
Plus, do not annoy the user with a LOG_INFO when the command
"add_usage_text" replaces an empty usage.
Change-Id: I4a72646e0fb704ba354f938d774055540cde3967
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5025
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command '%s' does not have the '.usage' field filled out
While there, fix some minor typo in the help messages:
s/deasert/deassert/
s/Deasert/Deassert/
Change-Id: If3dd18265cda103ca0d05609f67f4ca58e7cbb27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5024
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command 'swd' does not have the '.usage' field filled out
Change-Id: I5a36c0fc822c4d5d74ef2d1c75e369648c6f7d4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4830
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add usage and fix the help text of the command
Change-Id: I0e157d76f5d87bcda80f82a110912994908c8e03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5023
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Remove the numeric parameter <bank> from help and add it to usage
Change-Id: I630ca5450955210299f54e16fe5c9e8e51b3b266
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5022
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The only allowed parameter is the string "enable"
Change-Id: Iefdad38f1b4177e4194e58caf2be654357299ded
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5021
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio
or gpio property.
Dump the previously set values when commands bcm2835gpio_speed_coeffs
or bcm2835gpio_peripheral_base are executed with empty command-line.
Change-Id: Ie45d8268c1de331aded0bb52d5e6b8f0e8766a5b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5019
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio
or gpio property.
Dump the previously set values when commands imx_gpio_speed_coeffs or
imx_gpio_peripheral_base are executed with empty command-line.
Change-Id: Id56a68622817101bd0a46fed1fead6d2cd2b6ec6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Chained command require a subcommand as first argument. The usage
field for chained commands is not really important because the
"help" command will list all the subcommands with their respective
usage.
Add a empty usage field on all chained command.
The command "jlink config" can be either followed by a subcommand
or used alone, so use a dedicated usage string.
Change-Id: I43c3f8a766f96a9bdab4e709e3c90713be41fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5017
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no need to split the string in two lines.
Change-Id: Ifc574904acd06c31fab589643334e86f4dd0a122
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5016
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Keep using the same indentation rules while initializing struct
command_registration.
Change-Id: I900924600753ee7a72ca45da13db4112ab4b1522
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5015
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Keep using the same indentation rules while initializing struct
command_registration.
Change-Id: Ie69d9d6a786e1ef0abbcfd3eef89a61206238ebe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5014
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: Iefaeb15cc051db9f1e0f0140fe2f231b45f5bb12
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5013
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I65d32870bf4d3df845db69682fe445c71642f976
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I9ef7ac08e7cd5b82a6a7896c47017943d668925f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5011
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I743457acf7757df4646c9bc4e5ea1a6f9c841516
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5010
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The struct log_command_handlers[] is never modified.
Add const qualifier to it.
Change-Id: I5785aeb09ae9c23eaf7c34a05b88d0c7285f2d78
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
ctrl-z usage is incorrectly commented as ctrl-d
Change-Id: I54fe1775760ee984154bbae380baa38bcaffa04e
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fixed the small typo.
Change-Id: Ia8834b23302d25e92cb2fa0802bebb2a9416595b
Signed-off-by: Mete Balci <metebalci@gmail.com>
Reviewed-on: http://openocd.zylin.com/5001
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Andreas Fritiofson
Alexey Brodkin
Antonio Borneo
Bohdan Tymkiv
Moritz 'Morty' Strübe
Tim Newsome
Christian Meusel
Seth LaForge
Christopher Head
Marc Schink
Khem Raj
Tarek BOCHKATI
Caleb Szalacinski
Han Hartgers
Omair Javaid
Tilman Sauerbeck
Tomas Vanek
Michael Schwingen
Daniel Goehring
Florian Fainelli
Oleksij Rempel
Leonard Crestez
Jan Matyas
Megan Wachs
Paul Fertser
Tommy Vestermark
Mete Balci
Peter Lawrence