Commit Graph

9531 Commits

Author SHA1 Message Date
Tomas Vanek c2cb4e40b8 flash/nor/stm32l4x: use flash infrastructure to align write
The original code paded the write chunk with random bytes by overrunning
the buffer. An user can easily regard the random bytes to
be a programming error.

Change-Id: Ib0f47b5bc406bc6a7c32f3d929bf324a17c7c1e1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5359
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
2020-01-27 16:59:57 +00:00
Marc Schink 634e09f4e7 tcl/board: Add config for STM32WB Nucleo board
Change-Id: Ic29802306c706bcf3e261c60facd01d101c9e1ce
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5358
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ilya Kharin <akscram@gmail.com>
2020-01-27 16:59:21 +00:00
Tomas Vanek dc95dd036f target/arm_cti: fix regression from Tcl_return_values series
Since commit 7f260f5009 native OpenOCD
command handlers should not directly use Jim_SetResult functions.
The Tcl result of a native command is built as concatenation of
command_print() strings and Jim_SetResult() is called after return
of the command handler.

Replace "wrong number of args" error messages (now not delivered to user)
by simply return ERROR_COMMAND_SYNTAX_ERROR

Change-Id: I40c1374a13859cefbdef68e0f1c13ab93538bd50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5363
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
2020-01-27 09:19:17 +00:00
Marek Vasut ddbd8dcf91 flash/nor/nrf5: Fix build error on OSX
The chip->hwid is uint32_t , fix the print format.
This was detected by TravisCI on OSX, where this triggers a build error.

Change-Id: I776a7bb50e396c8fccc24500dec4750190da7982
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5401
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ilya Kharin <akscram@gmail.com>
2020-01-27 09:16:49 +00:00
Antonio Borneo 60aaf14837 jtag: drivers: xlnx-pcie-xvc: fix build after merge
Commit [1] was submitted in gerrit well before the conflicting
commit [2] get merged in master branch. While it was fine
committing in master branch [1] alone, it should not be
committed "as is" after [2].
Unfortunately gerrit did not complained committing [1] after [2].
The result is that master branch does not build anymore when the
driver xlnx-pcie-xvc is enabled at configure time by the optional
flag --enable-xlnx-pcie-xvc.

Apply to the driver the required changes as in [2].
While there, remove the duplicated struct xlnx_pcie_xvc_transports
and the struct field already implicitly initialized to zero.

[1] ff6d0704ec ("jtag: drivers: xlnx-pcie-xvc: Add support for
    Xilinx XVC/PCIe")
[2] efd1d64222 ("adapter: switch from struct jtag_interface to
    adapter_driver")

Change-Id: I5498479b802a231afbee1b845ae9775e1da7c728
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5402
Reviewed-by: Moritz Fischer <moritzf@google.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2020-01-22 12:49:59 +00:00
Marek Vasut 8b72657001 flash/nor/sh_qspi: Add SH QSPI driver
Add driver for the SH QSPI controller. This SPI controller is often
connected to the boot SPI NOR flash on R-Car Gen2 platforms.

Add the following two lines to board TCL file to bind the driver on
R-Car Gen2 SoC and make SRAM work area available:

  flash bank flash0 sh_qspi 0xe6b10000 0 0 0 ${_TARGETNAME}0 cs0
  ${_TARGETNAME}0 configure -work-area-phys 0xe6300000 -work-area-virt 0xe6300000 -work-area-size 0x10000 -work-area-backup 0

To install mainline U-Boot on the board, use the following procedure:

  proc update_uboot {} {
    # SPL
    flash erase_sector 0 0x0 0x0
    flash write_bank 0 /u-boot/spl/u-boot-spl.bin 0x0
    # U-Boot
    flash erase_sector 0 0x5 0x6
    flash write_bank 0 /u-boot/u-boot.img 0x140000
  }

Change-Id: Ief22f61e93bcabae37f6e371156dece6c4be3459
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
V2: - Add Makefile and linker script for the SH QSPI IO algorithm
    - Include the algorithm code instead of hard-coding it
Reviewed-on: http://openocd.zylin.com/5143
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-22 05:50:20 +00:00
Oleksij Rempel d612baacaa jtag_libusb_bulk_read|write: return error code instead of size
A USB bulk write/read operation may fail with different errors:
 LIBUSB_ERROR_TIMEOUT if the transfer timed out (and populates transferred)
 LIBUSB_ERROR_PIPE if the endpoint halted
 LIBUSB_ERROR_OVERFLOW if the device offered more data, see Packets and overflows
 LIBUSB_ERROR_NO_DEVICE if the device has been disconnected
 another LIBUSB_ERROR code on other failures

Current OpenOCD code is using the transfer size based error detection.
Which may not always work. For example for LIBUSB_ERROR_OVERFLOW as libusb
documentation says:
"Problems may occur if the device attempts to send more data than can fit in
the buffer. libusb reports LIBUSB_TRANSFER_OVERFLOW for this condition but
other behaviour is largely undefined: actual_length may or may not be accurate,
the chunk of data that can fit in the buffer (before overflow) may or may not
have been transferred."

This patch is refactoring code to use actual error return value for
error detection instead of size.

Change-Id: Iec0798438ca7b5c76e2e2912af21d9aa76ee0217
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4590
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-22 05:33:31 +00:00
Jiri Kastner f98099507f mips_ejtag: there is no DCR.MIPS64 bit
available revisions (2.60, 3.10, 5.06 and 6.10) of
MD00047 (EJTAG specification), have only in IMPCODE
MIPS32/MIPS64 bit/flag.

Change-Id: If9191b6ced760c59bb7551bb041cd72b0a060bb1
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/4628
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
2020-01-20 06:28:49 +00:00
Moritz Fischer ff6d0704ec jtag: drivers: xlnx-pcie-xvc: Add support for Xilinx XVC/PCIe
Add support for Xilinx Virtual Cable over PCIe JTAG controller.
It is commonly used in Xilinx based PCI Express designs with JTAG IP
in the FPGA fabric.

Access to the JTAG registers happens via the PCI Express extended
configuration space.

This can be used to debug soft-cores instantiated in the FPGA fabric.

The clang static checker doesn't find any new problems with this change.

Change-Id: Ib12ede0d1f26dacfda808d5e05b947b640c5bde7
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marex
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-17 05:21:29 +00:00
Marek Vasut f22883e8c1 flash/nor: Rename flash_address() to cfi_flash_address()
This is a preparatory change, align the function name with the rest
of the API, no functional change.

Change-Id: I6a810d2a54edcd13ad9a87d24a7334802c41623b
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5391
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 12:26:23 +00:00
Marek Vasut 76de1c8de1 flash/nor: Rename get_cfi_info() to cfi_get_info()
This is a preparatory change, align the function name with the rest
of the API, no functional change.

Change-Id: Ib967520f027b03eb1792b36ede52335df8e23941
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5390
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 12:26:16 +00:00
Marek Vasut 3192717ae9 flash/nor: Allow CFI memory read/write functions be overriden
Add possibility to supply custom CFI memory accessors via cfi_info
and override the default memory-mapped ones.

Change-Id: I1b6bc1db69fc33e8cdef96c41742c40e6d8917e9
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 12:26:03 +00:00
Marek Vasut 515a30f720 flash/nor: Drop size argument of cfi_target_{read,write}_memory()
The size argument is always set to bank->bus_width and bank pointer
is now passed into cfi_target_{read,write}_memory(), so the size
can be accessed through the bank pointer inside the function instead
of being explicitly passed in.

Change-Id: I0abc1cc3bf513281c10cb5de7a21cb0e75cb7676
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5389
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 12:25:53 +00:00
Marek Vasut f83ce0a2ef flash/nor: Pass flash_bank to memory accessors
Replace passing in struct target with passing in struct flash_bank,
so that the later can contain function pointers to custom per-driver
memory accessor functions.

Change-Id: Id2573a6d5f1a73ed9c4f73c53592a9a335a11c99
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5146
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 12:25:44 +00:00
Tomas Vanek 7fffa3cbc6 target/xscale: remove duplicated command
Reported by clang static analyzer.

Change-Id: I893af10852af4885507ed62d024008159a80dd56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5382
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:46:38 +00:00
Tomas Vanek af0dda8266 target/etm: add check for calloc error
and fix one more clang static analyzer warning.

Change-Id: I17f03e318e1cf7617e7f753e7ca960552be547e5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5381
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:46:27 +00:00
Tomas Vanek fe6bb7eac8 target/semihosting_common: fix minor memory leak
Reported by clang static analyzer.

Change-Id: Ie663f49d92588c0d8b502cfdd8fc34004b308066
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5380
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:46:12 +00:00
Tomas Vanek 57afa176ce target/target: fix clang static analyzer warnings
Change-Id: I23e6586be60915f21a7179a994a1ec93fb9b2c36
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5379
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:45:58 +00:00
Tomas Vanek b04d9c05f0 target/avr32_jtag: fix error returns
Fixed only 2 error returns discovered by clang static analyzer.
There are obviously many more missing error tests in avr32_jtag.c
These was not fixed to keep this change minimal.
Not tested with hw.

Change-Id: I6c79f6248db774990ddb42c0dacdb621651ed69e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5378
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:45:37 +00:00
Tomas Vanek 8bb1998e6a target/arm_dpm: add missing error returns
Discoverd by clang static analyzer.

Change-Id: I93d5de0a36216e62b170fe8cc870431226a7777f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5377
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:45:30 +00:00
Tomas Vanek 5dd5cf26bd target/arm946e: add missing error detection
Discoverd by clang static analyzer.
While on it remove useless type casts from arm946e_read_cp15() parameter.

Change-Id: I549e19685b431400243800ee0f7d1bbe6cdb14b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5376
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:45:19 +00:00
Tomas Vanek 98a8b99ef3 server/server: fix clang static analyzer warning
Change-Id: I317e189b62540e3688a20d88a95f551280317f14
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5373
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:44:49 +00:00
Tomas Vanek 35d9bf9917 xsvf: fix memory leak
Discovered by clang static analyzer.

Change-Id: I2980586aea5ee43226adb1f4cf72e7ba1dfddd83
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5372
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-16 09:44:33 +00:00
Tarek BOCHKATI 251eb035fc flash/nor/stm32l4x: add support of STM32L4P5/L4Q5x devices
STM32L4P/Q devices have:
 - similar flash layout as STM32L4R/S devices
 - 1024K of flash memory (some parts have 512K only)

tested on NUCLEO-L4P5ZG using board/st_nucleo_l4.cfg

Change-Id: I77047351bc7dcd7c76d0f31a77be73005104a06f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 09:41:35 +00:00
Tarek BOCHKATI a6a642bf72 flash/nor: add support of STM32WB on top STM32L4 flash driver
Change-Id: I9fb6700085d817d35a691f6484193f67939a4e0f
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4933
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 09:38:52 +00:00
Tarek BOCHKATI 8536306b6e flash/nor: add support of STM32L41/L42xx
tested using STM32L412KB

Change-Id: I1e2ae93d8c740db219f0fb579940de7f2fffac15
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4934
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-16 09:36:33 +00:00
Tarek BOCHKATI cc85ebc5ac flash/nor/stm32l4x : add structure containers to hold devices' information
This rework is inspired from the 'flash/nor/stm32h7x.c'
This rework will ease the support of new devices on top of this driver:
  for example: STM32WB have different flash base and size addresses

Notes:
 - stm32l4_probe modified in order to charge the correct part_info from
   the defined stm32l4_parts according to the device id
 - stm32l4_flash_bank.bank2_start is replaced by .part_info->bank1_sectors
 - STM32_FLASH_BASE is removed , part_info->flash_regs_base will be used instead
   based on that flash register addresses are changed to offsets,
   >> stm32l4_get_flash_reg was modified accordingly
 - stm32l4_read_option and stm32l4_write_option was modified to accept an
   offset instead of an absolute address, luckily this is the commands'
   argument by default
 - stm32l4_mass_erase modifications :
     - use MER2 only on top of dual bank devices
     - wait for BUSY bit before starting the mass erase

Change-Id: Ib35bfc3cbadc76bbeaaaba9005b82077b9e1e744
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4932
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
2020-01-16 09:34:42 +00:00
Christopher Head ed8fa09cff target/target: parse value as proper type
The `value` variable is passed into `target_fill_mem` as its
second-to-last parameter. That parameter is of type `uint64_t`. It is
appropriate to parse the value as that type, since otherwise a target
with a 32-bit address space but 64-bit data write capabilities would not
be able to exercise those capabilities.

Change-Id: Ib336d47d42c27cd2b5ba1206b04e8f740f167dba
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5219
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
2020-01-14 11:41:11 +00:00
Antonio Borneo d2308da6e9 stlink: fix handling of DPv1 and DPv2 banked registers
Arm DPv1 and DPv2 support banked registers by setting the bank in
field DPBANKSEL of register DP_SELECT.
Old ST-Link firmware don't support banked registers and setting a
bank other than bank zero on DPv1 or DPv2 cause issues in the
firmware because it cannot set back bank zero to read CTRL/STAT.
New ST-Link firmware mask away DPBANKSEL bits while writing in
DP_SELECT but support banked register using the same packed method
used by OpenOCD:
	#define BANK_REG(bank, reg) (((bank) << 4) | (reg))

Add a new macro STLINK_F_HAS_DPBANKSEL for firmware that support
arm DPv1 and DPv2, plus trigger an error if banked registers are
requested on old firmware.
Prevent changing DPBANKSEL on old firmware.
Log a debug message when changing DPBANKSEL will be ignored.

Change-Id: Iaa592517831d63f8da2290db54f6b32504e3081b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4978
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:40:45 +00:00
Antonio Borneo 944d3e6771 stlink: add DAP direct driver
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.

This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.

Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:40:36 +00:00
Antonio Borneo a61ec3c1d7 adi_v5_dapdirect: add support for adapter drivers that provide DAP API
Some high level adapters, like STLINK-V3 and new firmware for
ST-Link/V2, provide API to directly access the DAP registers
hiding the details of the physical transport JTAG or SWD.
OpenOCD has already the intermediate API in struct dap_ops that
are suitable for such adapters, but are not exposed to the
adapter drivers.

Add in struct adapter_driver two independent struct dap_ops for
the cases of physical JTAG and SWD transport.
Add new transport names "dapdirect_jtag" and "dapdirect_swd", to
be used by the drivers that provide one or both DAP API.
Add the necessarily glue in target/adi_v5_dapdirect.c

Change-Id: I2bb8e3a80fba750f2c218d877cfa5888428e3c28
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:40:25 +00:00
Antonio Borneo c6b6fdeb2c TODO: add restructuring of JTAG/adapter layer
SWD is already implemented, so remove the item.
Rename the section JTAG as Adapter, including the subsections.
Add an initial list of pending activities after the restructure
of the JTAG layer.

Change-Id: I540777344c62a746df8347538fe8b29e4d72e1c7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4901
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:39:44 +00:00
Antonio Borneo efd1d64222 adapter: switch from struct jtag_interface to adapter_driver
To reorganize the adapters code, introduce an adapter_driver
struct that contains all the adapter generic part, while
keeping in two separate struct the specific API jtag_ops and
swd_ops.
Move the allocation of *adapter_driver from the JTAG-specific
file core.c to the more adapter-specific file adapter.c
While splitting the old jtag_interface for every driver, put
the fields in the same order as in the struct declaration so
we keep a consistent code across all the drivers.

While other transport specific API could/would be added as
separate ops, nothing is done here for HLA.

Change-Id: I2d60f97ac514c0dd2d93a6ec9be66fd9d388dad5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4900
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:39:37 +00:00
Antonio Borneo 7268ff22c3 drivers/kitprog: remove unused JTAG execute_queue method
kitprog is SWD only and we do not rely on JTAG queue anymore.
Remove the remaining JTAG heritage.

Change-Id: Ic586278368301eb669bc6e4e641f683a81cb171d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4899
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:39:25 +00:00
Antonio Borneo b5621bf2f9 hla: remove empty JTAG execute_queue method
We do not rely on JTAG queue anymore.
Remove the remaining JTAG heritage.

Change-Id: I6c87d9ffebaa383c998cf273188b3e7f28b3fe95
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4898
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:38:39 +00:00
Antonio Borneo f275ae586b jtag: print an errmsg on using jtag API for non jtag transport
After the cleanup of swd and hla, there should be no more calls
to jtag_execute_queue() or to queue jtag commands if current
transport is not jtag. Thus we can start removing the jtag
specific code from adapters that do not support jtag.

To prevent some remaining call to jtag_execute_queue() to crash
openocd, verify the transport, print an error message if the
transport is not jtag, call the adapter's jtag_execute_queue()
only if it exist.
To identify code that still add commands in the jtag queue even
if transport is not jtag, print an error message in the function
jtag_queue_command(). For the moment, still queue the message,
even if will cause a memory leak if there is no following call
to jtag_execute_queue(); the target is to identify the issue and
cleanup the code, thus solving also the leak.

Change-Id: I8fc85f754aa057aad1df05ff0448c8619897da23
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4897
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:38:23 +00:00
Antonio Borneo 0f24549ce9 hla: use the new system_reset API
HLA uses its own internal driver's API to control the adapter's
system reset, but at the same time it calls jtag_add_reset() to
avoid breaking the internal logic of OpenOCD. This implicitly
forces HLA to rely on jtag queue mechanism, even if HLA has no
link with JTAG state machine. It requires HLA to implement an
empty execute_queue() to comply with the JTAG queue.

Modify the HLA framework and the HLA targets to use the new
adapter API for system_reset and decouple HLA from JTAG queue.
Rename the HLA static functions adapter_assert_reset() and
adapter_deassert_reset() to avoid overlap with the global
functions with same name.
While there, fix a minor typo in a comment s/incase/in case/.

Do not remove from HLA the JTAG specific API execute_queue(),
even if not required anymore, because OpenOCD code still has
calls to jtag_execute_queue() in case of non JTAG transport.

Change-Id: I0e65e3e557bd665bd3d3aeaa84ea609b55a05e48
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4896
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:37:34 +00:00
Antonio Borneo 9daec098a9 bitbang: jtag-only drivers: switch to new reset API
Remove the JTAG_RESET command from the bitbang execute queue now
that all bitbang drivers have moved away from old reset method.
Remove also the internal reset API in struct bitbang_interface.

Tested parport only.

Change-Id: I12b157ef442f4c9912406b19b7a4d32ba6ec0b53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5300
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:16:24 +00:00
Antonio Borneo 8850eb8f2c swd: get rid of jtag queue to assert/deassert srst
The transport SWD uses the JTAG queue to assert/deassert the
system reset srst. This is the major inconsistency that has to be
removed to properly split JTAG and SWD.

Introduce a new driver API, reset(), to controls both the signals
trst and srst in the driver, skipping the JTAG queue. Put the new
API in struct jtag_interface, even if in this patch it's used for
SWD only; the goal is to get it reused by the other transports.

Add the implementation of the API in all the drivers that
implement SWD. Such implementation is almost the same of the old
code in JTAG queue.

Create a wrapper adapter_system_reset() to use the new API and
remove the SWD specific swd_add_reset(). In the wrapper replace
jtag_add_sleep() with jtag_sleep(), because the former uses the
JTAG queue too.
Rename the old jtag_add_reset() as legacy_jtag_add_reset() with
the target to remove it when all drivers would be ported to the
new reset API. Create a new jtag_add_reset() that calls the
legacy function for drivers still on the old reset API.

Use the new API also on JTAG transport for the drivers that can
support both SWD and JTAG.

For the moment, do not modify the implementation of JTAG-only
drivers, which will continue using the usual method. This should
be cleaned-up in future commits.

Change-Id: I32331c88313f6059b25e12c6bb0156aebc1c074f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:15:12 +00:00
Tim Newsome 69e6891434
Handle DMI busy in sba write. (#437)
* Handle DMI busy in sba write.

If we encounter DMI busy on the NOP after a read, we'll never get the
value out because DMI busy is sticky. The read must be retried, but we
don't know whether it was ever issued. Since the read has side effects
(incrementing of the address) this retry must be handled at a higher
layer. So now dmi_op_timeout can be told to retry or not, and if retry
is disabled it'll return an error when busy.

Also actually properly do the retry in dmi_op_timeout(). Previously the
code would not reissue the command and end up returning a garbage value.

Change-Id: I3b52ebd51ebbbedd6e425676ac861b57fbe711b1

* Fix whitespace.

Change-Id: Icb76d964e681b22346368d224d1930c9342343f3

* Handle a few more DMI busy cases.

Change-Id: I8503a44e4bf935c0ebfff0d598fe4c322fda702a

* Explain when to use dmi_op_timeout(retry).

Change-Id: I1a5c6d76ac41a84472a8f79faecb2f48105191ff

* dmi_reset does not affect the current transaction.

That means the retry scheme we had been using works fine. This does
contain some minor tweaks, and now we pass my tests which hammer the DMI
busy case harder.

Change-Id: I13eee384dbba82bc5a5b1d387c75c547afe557b5

* Remove unnecessary changes to make the PR readable

Change-Id: I87079876e6965563cf590e3936b3595aeab8715d

* Move idle to end of line...

... because we go through run-test/idle after the scan.

Change-Id: I21a8cff22471f0b895d8cd8d25373dced9bf1ca9

* Remove unused code.

Change-Id: I07a7cdd2d64ca40a4fe181111a34cf55ff1928d1
2020-01-13 15:10:43 -08:00
Jan Matyas fcea4f79ba Don't issue extra FENCE+FENCE.i for the current hart. (#439)
The original OpenOCD code issued FENCE & FENCE.i twice for the current
hart (which is harmless, but takes time).

Avoiding this extra FENCE is a slight performance improvement. Per my rough
measurements, this improves performance of certain debugger actions
(single-stepping) by approx. 20% in single-hart systems.
2020-01-10 12:29:10 -08:00
Tim Newsome 8b8db033ee
Upcast mask value to work with 64-bit physical (#436)
Change-Id: I00f0d2a3c79a431e1aa49c7478fa6c17e2fa5256
2020-01-06 16:57:15 -08:00
Marek Vasut db23c13d42 flash/nor: Factor out CFI memory read/write functions
Create separate memory read/write functions which facilitate access
to the CFI NOR, so that they can be replaced by controller-specific
functions if necessary. This would become necessary when implementing
support for e.g. HyperFlash controllers, which do not directly map
the HyperFlash into the address space.

Change-Id: I1bba1edfd397cb37bfedb43efe2dd03feb26a375
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5145
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2020-01-05 14:29:57 +00:00
Marek Vasut 790bd27181 flash/nor: Factor out cfi_spansion_unlock_seq()
Factor out the spansion unlock sequence to deduplicate the code.

Change-Id: Id78522e9a2f0e701870ef816772289d08257476a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5144
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2020-01-05 14:26:54 +00:00
Keir Fraser 9f1529da4f flash/nor/stm32f2x: Support value line chips with trimmed flash
The current code assumes an STM32's flash bank is laid-out in either of
two configurations:
- 4 x 16kB + 1 x 64kB + n x 128kB
- 4 x 32kB + 1 x 128kB + n x 256kB

This is quite ad-hoc but works fine in practice, as long as there are at
least 5 sectors (if n=0). Unfortunately, some newer STM32s are shipping
with only 64 kB of flash (4 x 16kB sectors).

This patch still assumes the same sector layout, but only keeps adding
sectors to the bank if the bank's capacity has not been reached. This
prevents openocd from crashing on some newer STM32s.

Change-Id: If00e5d7a328d11b399babc0bb2111e3ad8a3217e
Signed-off-by: Romain Goyet <romain.goyet@numworks.com>
Signed-off-by: Keir Fraser <keir.xen@gmail.com>
Reviewed-on: http://openocd.zylin.com/4926
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-03 10:28:45 +00:00
Antonio Borneo be2d25efcc arm_adi_v5: add API send_sequence() and use it
The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().

Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h

Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-02 21:24:54 +00:00
Antonio Borneo 5d08bcb715 tcl: update scripts after "jtag_reset" got deprecated
Avoid annoying "deprecated" messages in the scripts
distributed with OpenOCD code.

Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5287
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-02 21:24:45 +00:00
Antonio Borneo c07b774e8f jtag: replace command "jtag_reset" with "adapter [de]assert"
Replace the JTAG transport specific command with a more generic
one. Deprecate "jtag_reset" and update the documentation.
While there, fix an error in the documentation, where the command
"jtag_reset" was used in place of command "reset_config".

Change-Id: I41a988d37ce69f7b35a960cbaf5306aab0299b99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5286
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-02 21:24:38 +00:00
Antonio Borneo fafe6dfc9c adapter: add command "adapter [de]assert srst|trst [[de]assert srst|trst]"
Inspired from http://openocd.zylin.com/#/c/3720/1

Add commands to control the adapter's signals srst and trst.
Add macros for the flag's values assert/deassert to make clear what
they mean and to propose a uniform set of values across the code.

Change-Id: Ia8b13f4ded892942916cad7bda49540a896e7218
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5277
Tested-by: jenkins
2020-01-02 21:24:30 +00:00
Jan Matyas deff24afa1 jtag_vpi: multiple improvements
- Fix: Proper handling of read_socket() and write_socket()
in case of "partial" read/write.

- Added low-level JTAG IO debug capability (_DEBUG_JTAG_IO_)

- Zero-fill packet buffers, avoid sending pieces of uninitialized
memory over the network (memset struct vpi_cmd)

- Use close_socket() instead of close() - needed for Win32

- Fixed usage messages of jtag_vpi_command_handlers

Change-Id: I8bd19bc5c9512fe8e798600212e8a95213f50f5b
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5177
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-02 21:22:33 +00:00