Add the new STM32F446 mcu with 512 Ko
Tested with a eval board
Change-Id: I0c16ce7d32d249c7634d697815207c20e7f778c4
Signed-off-by: prudhomme.remi@gmail.com
Reviewed-on: http://openocd.zylin.com/2484
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The message as it was didn't let the user know that something was wrong
with the target or wiring.
Change-Id: Ib609c2d31959e77413e61c348d0e31d7269d5c58
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Jens Bauer <jens@gpio.dk>
This adds a trivial config for LPC8xx chips based on the already
existing infrastructure in lpc1xxx.cfg.
Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2464
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Also remove an unrelated no-op cast.
Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2473
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This helps to uncover incorrect usage when a pointer to uint32_t is
passed to those functions which leads to subtle bugs on BE systems.
The reason is that it's normally assumed that any uint32_t variable
holds its value in host byte order, but using but_set_u32 on it
silently does implicit pointer conversion to (void *) and the
assumption ends up broken without any indication.
Change-Id: I48ffd190583d8aa32ec1fef8f1cdc0b4184e4546
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Do not use buf_set_u32 on integers; they're not buffers.
If using buf_set_u32 on integers, bytes will be exchanged on Big Endian targets.
In this particular case, FLASH_OPTCR was incorrectly written, causing it to often
contain one of these values: 0x00aaaae1, 0x00aaffef, 0x00ffabe1 or 0x00abffe1.
This write-protected the device before flash-programming, causing this command...
flash write_image erase unlock myfile.elf
... to fail, complaining about write-protection.
Repeating the above command would change the OPTCR register each time.
After applying this patch, the OPTCR remains "unchanged".
Change-Id: I73d510fcc2e81a01973ad5c6e1aa22715ebd2743
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2466
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Mass erase operation might be impacted by different factors,
apparently the most reliable way is to do it while asserting the chip
reset line.
Change-Id: Id6ab57eaec86e402ffdf4f5c8843e7735640f03e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2424
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Enable auto-creating additional discovered TAPs even if some TAPs are
predefined, avoiding initialization failure when it's not necessary.
Also, drop the arbitrary limit on the number of predefined TAPs. Still,
don't auto-create any if there are more than 20 TAPs already, to stop
a noisy connection from creating unlimited TAPs.
Create auto-probed TAPs with less noise.
Reduce code duplication between verification and auto-probing.
Change-Id: I82a504d92dbcc0060206e71f10c5158256b5f561
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The default label does just return the same error code as the case for
zero, so this can be handled by a simple if statement.
Change-Id: I61a8cb51b5e261f21eca386af7d8cbf17ffa2d44
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/2430
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the serial wasn't actually used in hid_open() call,
which meant that the first device with matching vid:pid was opened
irrespective of the actual serial number.
Change-Id: I45216ae5d9e0798e97be693c30e2f03c89b9a02b
Signed-off-by: Jaakko Kukkohovi <jkukkohovi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2487
Tested-by: jenkins
Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As of RM0091, Rev. 7, all F0 have the same revisioning scheme.
Change-Id: I0b344a1d3ca3f61f48fa151e83c549ca5333ae47
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2457
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for the ST nucleo l152re board with a stm32l152ret6 MCU,
analog to st_nucleo_f* configurations.
Change-Id: Id2c61dc7a7cb2e1cc64442191b367bab4247bdeb
Signed-off-by: Thomas Eichinger <eicht@lepus.uberspace.de>
Reviewed-on: http://openocd.zylin.com/2489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It depends on the particular target whether it can work with SRST
asserted or not, so this belongs to the target config rather than the
board config.
Also, this allows for simple
openocd -f myboard.cfg -c "reset_config connect_assert_srst"
command to be used whenever a user feels a need to connect to an
unresponsive target.
Change-Id: I3d8da9ae47088fc0c75a20bfdd20074be1014de0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2459
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
So remove it from all the configs, it's misleading, and leads to cargo
culting of config files.
Change-Id: I2b77e60d5e96f9759c7c9fc91b20e73be2e95d9a
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is an integrated adapter used on the IoT-LAB boards.
Schematics are available from
https://github.com/iot-lab/iot-lab/wiki/Docs/openm3-schematics.pdf
Change-Id: I1c80e72653c3f319bb04d01e3dfddb1c2447c398
Tested-by: Quentin Lampin <quentin.lampin@orange.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2415
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It is derived from ti_tmdx570ls31usb.cfg, using a different TAP ID.
Change-Id: I2d911995c76ea4f75a780cc230d61f4959825809
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2440
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ability to change the speed has been added to firmware versions J22 and
above. Any attempt to change on earlier versions will be ignored without error,
as the existing code does.
For supported firmware versions the driver will attempt to get as close as
possible to supported speeds (never higher).
The default stlink speed on power up is 1.8MHz.
The driver will now also print supported clocl speeds during init.
Change-Id: Iee9bd018bb8b6f94672a12538912d41c23d48a7e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2335
Tested-by: jenkins
As a note we need to cache the requested speed setting, as the
hla interface may not be ready when the first adapter_khz is called.
Change-Id: I2fa6807d5f0bd3f0365cf178bd10a230c39415a7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2334
Tested-by: jenkins
This should have been corrected earlier with the split of l1/l0 code
apart.
Change-Id: I87b94a310ae7e76318554a9cd2705348a942d58b
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2447
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Output a similar message to what we have on low-level JTAG adapters to
avoid confusing users. Reported on IRC by chickensk.
Change-Id: I96d58410ef715b966e32d79c0aacf38596c5eb3f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2451
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Previously the jtag_add_reset(1, 0) caused the processor to be released,
and if SRSTn existed then it would then be reset again two lines later.
Change-Id: I58b7a12607f46f83caa7ed3b3cebc4195eb51ef6
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/2398
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds flash programming support for LPC5410x and LPC82x.
And adds auto flash size detection for LPC800 series.
Tested on below listed boards/chips.
LPC54102(LPCLPC54102Xpresso)
LPC824(LPCXpresso824-MAX)
LPC812(LPC812MAX)
LPC811,LPC810
Change-Id: Ie68b6d425b17ccfa83814607ee61056e99800c1c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2442
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
A7 MPCore needs unlocking the debug registers same as with A15 MPCore.
Found out by hacking on the code.
Change-Id: I613cb4fb35007b85b4a9a401577b47768bc1a08b
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-on: http://openocd.zylin.com/2344
Tested-by: jenkins
Reviewed-by: Kamal Dasu <kamal.dasu@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added Cortex-A15 support for DAP AHB-AP init code as per ADI V5 spec.
Also added changes to make the APB MEM-AP to work with A15.
Made the the cortex_a target code generic to work with A8, A9
and A15 single core or multicore implementation. Added armv7a code
for os_border calculation to work for known A8, A9 and A15
platforms based on the ARM DDI 0344H, ARM DDI 0407F, ARM DDI 0406C
ARMV7A architecture docs.
Change-Id: Ib2803ab62588bf40f1ae4b9192b619af31525a1a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1601
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When no transport is selected, the error message dumps the available
transports, but not how to actually select one.
Change-Id: I63da2a4b59e3f6cc8d30bd631e41a82636a056ef
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
commit b5a6ba46 broke the following board files, update to new cfg.
Change-Id: Ic3b776bd32eb72eae6ad1e130e329268ce9ba71a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2384
Tested-by: jenkins
For example "bp 0x20000000 8 2" makes openocd segfaulting on a
stm32f4x Discovery board.
Change-Id: I1ddd46b1fa9ade78db2234ed975ccefb72539331
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/2342
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GCC-4.2 on Mac/PPC complains about size_t is expected for %zx and the build stops.
In order to avoid other problems, I've chosen simply to typecast.
Change-Id: I99b569c4d1100e729712e31d24d6539f8b5971b6
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2360
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When communication with target fails for whatever reason, it makes
sense to do JTAG-to-SWD (in case the target got power-cycled or the
DAP method was reset anyhow), SWD line reset sequence (part of
JTAG-to-SWD already) and the mandatory IDCODE read. Schedule that to
be performed on the next poll.
Fix the return values for ftdi and jlink drivers to be consistent with
OpenOCD error codes and remove ad-hoc calls to perform DAP method
switching (as it's now done from the upper layer automatically).
Change-Id: Ie18797d4ce7ac43d8249f8f81f1064a2424e02be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2371
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mateusz Manowiecki <segmentation@fault.pl>
When a target was present on OpenOCD start but later disappeared for
whatever reason (typically unstable connection or target going to
sleep) and reappeared only for a brief period of time, reexamination
would fail, and poll would no longer run. This patch fixes it.
Change-Id: I61f9b5a3f366a761320e233f4e1689f926b5556d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2370
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Commit 4525c0a4c4 cherry-picked check
for the FSF address presence from upstream. However, it has a typo
resulting in this obscure error when triggered:
Use of uninitialized value in concatenation (.) or string at /home/jenkins/.jenkins/jobs/openocd-gerrit/workspace/tools/scripts/checkpatch.pl line 1258.
ERROR:
This patch fixes it.
Change-Id: Ia417ef4782d21c8b3f1d39de88c4ab850a5a6630
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2414
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Rémi PRUD’HOMME
Uwe Bonnes
Paul Fertser
Andreas Fritiofson
Jens Bauer
Uwe Kleine-König
Jaakko Kukkohovi
Thomas Eichinger
Karl Palsson
Jörg Wunsch
Andreas Färber
Spencer Oliver
Evan Hunter
Nemui Trinomius
Alexander Stein
Kamal Dasu
Tomas Vanek
Karl Palsson
Salvador Arroyo