Resolve a "FIX" comment; yes that was superfluous given that the
JTAG core does that check by default. It was also buggy since it
wrote to a stack frame that went away before the write happened!!
Other fixes: remove pointless malloc(); zero-init scan_field_t
values wherever they appear; whitespace scrub; spelling fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Load the XScale debug handler from the read-only data section
instead of from a separate file that can get lost or garbaged.
This eliminates installation and versioning issues, and also
speeds up reset handling a bit.
Plus some minor bits of cleanup related to loading that handler:
comments about just what this handler does, and check fault codes
while writing it into the mini-icache.
The only behavioral changes should be cleaner failure modes after
errors during handler loading, and being a bit faster.
NOTE: presumes GNU assembly syntax, with ".incbin"; and ELF,
because of the syntax of the ".size" directive.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Streamline/shrink some needless JTAG stuff:
- Use #defines for the JTAG instructions; they can't ever change
- Remove an unused (!) shadow of tap->ir_length
- Stop using a copy of target->tap
- Don't bother saving the variant after sanity checking ir_length
Also, make target_create() work as on other targets: build the
register cache later, making init_target() no longer be a NOP.
Handle malloc failure; remove a comment that was obsoleted by the
not-so-new target syntax.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove unused and deprecated (in the arch spec) mode for loading
code into the *main* icache (vs the "mini" icache). Disable some
extremely noisy (and rarely useful) low-level debug messages
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Declare almost everything as static.
Move stuff to remove most forward references.
Remove most forward declarations.
Warn if the unimplemented register functions get called.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Just fill out the rest of the cache line with NOPs; don't change
the record of how much data we consumed. Otherwise the count of
how much data is left can roll over from positive to negative
("VERY positive") and skip the loop termination of zero.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a header comment referencing useful XScale specs.
Make most data static, and the tables readonly.
Scrub extra blank lines.
Return fault codes from one routine.
Remove a needless NOP methood.
(BUGFIX) When we update R0, mark R0 as dirty/valid ... not R15/PC!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix formatting and layout bugs in the new "translating configuration
files" bit. Make it a section within the chapter about config files.
Add a crossreference.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We added two overridable procedures; document them, and the
two jtag arp_* operations they necessarily expose.
Update the comment about the jtag_init_reset() routine; it's
been obsolete for as long as it's had SRST support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Startup now mostly works, except that the initial target state
is "unknown" ... previously, it refused to even start.
Getting that far required fixing the ircapture value (which
can never have been correct!) and the default JTAG clock rate,
then providing custom reset script.
The "reset" command is still iffy. DCSR updates, and loading
the debug handler, report numerous DR/IR capture failures.
But once that's done, "poll" reports that the CPU is halted
(which it shouldn't be, this was "reset run"!), due to the
rather curious reason "target-not-halted".
Summary: you still can't debug these parts, but it's closer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This abstracts the "jtag arp_init-reset" call into a method
called from OpenOCD startup and reset processing.
Platforms which have different requirements for how such hard
resets must be performed can now override "init_reset" instead
of needing to rebuild custom hacked versions of the server.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is clearly noted in the hardware spec (section 5.2.3); it
works around a chip erratum: "If the MPU_RESET signal is used,
it may cause the EMIFS bus to lock."
I seem to have a board with such an initial build. The chip
is labeled XOMAP. Presumably, parts without that "X" prefix
(eXperimental) resolve this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Observed:
openocd: core.c:318: jtag_checks: Assertion `jtag_trst == 0' failed.
The issue was that nothing disabled background polling during calls
from the TCL shell to "jtag_reset 1 1". Fix by moving the existing
poll-disable mechanism to the JTAG layer where it belongs, and then
augmenting it to always pay attention to TRST and SRST.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Among other things this causes startup errors to kick in the
fallback "reset harder" logic during server startup. Comments
are also updated a bit, explaining what the various error paths
signify (in at least my observation).
There's one class of validation error that we can still plausibly
ignore: when wrong IDCODE values are observed.
This change seems to have helped make an OMAP5912 behave much
more reliably. There's still some post-reset flakiness, but
it's unrelated to scan verification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Without some extra delay after releasing SRST, we seemed to
be trying to talk to the TAP before it was ready to respond.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Also, talk about "mainline" not "trunk".
The release.txt and release.sh files need more updates.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2825 b42882b7-edfa-0310-969c-e2dbd0fdcd60
At least some FT2232 based adapters don't necessarily come up
in the expected state, with SRST and TRST disabled. Since
other adapters could suffer the same problem, let's avoid
needing to patch every driver and just force *all* adapters
to initialize those values properly at server startup.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2824 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Øyvind Harboe
David Brownell
Wookey
Rabeeh Khoury
John Rigby
dbrownell