This patch introduces function semihosting_opcode_to_str() which
converts semihosting opcodes to strings. This function is then
used in debug messages to improve log analysis and troubleshooting.
Change-Id: Iffea49dae13d6a626ae0db40d379cba3c9ea5bd3
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7726
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
* rtos/FreeRTOS: solve some conflicting usage of thread id.
1.
There are some RISCV-specific usage of thread_id, which has conflict with upstream.
Some adaptions are made in this patch, to make sure OpenOCD is sending a clear thread list to gdb.
2.
Use freertos_read_struct_value for xSchedulerRunning.
Change-Id: I001a88a0c6d8eac98a389c0217b4897f28124840
Signed-off-by: Chao Du <duchao@eswincomputing.com>
* fix typo.
Change-Id: Id6546cc74de44bbee7e44b7cb29b769a2f35ec4a
* correct the data type.
Change-Id: I28c7e111e569d94ba5f6e1ae21745ddb34d4dd12
* changes as per the review comment.
Change-Id: Ica4c705a8f2657700dc27e24790287ca802480fd
* another macro replacement.
Change-Id: Ia9330fed32d917cf87804051ba1b8d6ac42cfb7b
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
With this change, failures to resume a hart due to it not being halted
are more explicitly logged or reported as an error.
Change-Id: Ia55d8df85a908363d0f2140637ce1e47c1ab6251
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
This involves halting the target, which might have unintended side
effects, but when the debugger is connected software breakpoints must
trap to the debugger. Anything else is a terrible user experience.
Change-Id: I1f7bb610eeeb054cc3042dc6bcfc16589ce12a31
Signed-off-by: Tim Newsome <tim@sifive.com>
Intended as a place where we can interact with the target without too
much concern about preserving state and doing exactly the right thing
while poll() is going on.
Change-Id: Ic9bd441caae85901a131fd45e742599803df89b5
Signed-off-by: Tim Newsome <tim@sifive.com>
Specifically, call into the RISC-V version when target becomes halted,
running, or unavailable.
I'll be using unavailable shortly.
Change-Id: I9ffffdccbf22e053fe6390d656b362bf9ab9559a
Signed-off-by: Tim Newsome <tim@sifive.com>
Will be used later when we want to do a quick halt/resume.
Change-Id: Ib80166234c4c277b7d9ce26b7566ac0f93017e64
Signed-off-by: Tim Newsome <tim@sifive.com>
* Only set ebreak bits that might be supported based on misa.
* Don't write dcsr if its value wouldn't change.
Change-Id: I7087af0b0df0fbdbf994373b5c887b9b389df872
Signed-off-by: Tim Newsome <tim@sifive.com>
Make it callable earlier, handle `supported` being NULL, and make enum
names more clear.
Change-Id: If4d286b54ccfc01eb5de5a57eb18f748c920e979
Signed-off-by: Tim Newsome <tim@sifive.com>
The riscv013_on_halt function was being called but its implementation was
empty, providing no additional functionality. Removed the function declaration,
calls to it, and its implementation since it is not required.
Change-Id: I425ea890deadeec945f0a47af247f3f99172e801
Signed-off-by: Tim Newsome <tim@sifive.com>
Otherwise I get a compiler warning, which fails the build.
Change-Id: Ib7d4ab85160b537d07c74f8651ac42906fd661ed
Signed-off-by: Tim Newsome <tim@sifive.com>
When halted we don't need to read all 3 instructions before deciding the
sequence doesn't match.
Change-Id: I9f8345960ce27e859265af901a368166a70b9fde
Signed-off-by: Tim Newsome <tim@sifive.com>
* rtos/FreeRTOS: pxCurrentTCB should be used for judgment.
The current TCB is stored in pxCurrentTCB, which is somehow RISC-V-specific, should not be overwritten from upstream (#816).
* fix the code style check.
Signed-off-by: Chao Du <duchao@eswincomputing.com>
Change-Id: I9ffa8947f0cb9e93c7d96866882a5a1e8e69afad
* revert some over-changes in last commit.
Change-Id: Ie88bd75b59190503db11ee4538281bd13b554e50
Signed-off-by: Chao Du <duchao@eswincomputing.com>
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
The current cJTAG to JTAG switching commands for TI chips are not
particularly reliable, especially on chips with accurate timing.
On a Raspberry Pi the existing sequence has (depending on cabling and
chip) a ~50% chance of working, on a much better-behaved FT2232H
it doesn't manage to enable full JTAG at all.
This change runs a bunch of test-idle cycles before actually attempting
to switch to full JTAG. This makes the switch reliable even at high
clock speeds (>100kHz) and from precise sources like the FT2232H.
Change-Id: I9293e884bf3e9606d529756ae4483b844d3c39db
Reported-by: Phil Wiggum <p1mail2015@mail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/375/
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Reviewed-on: https://review.openocd.org/c/openocd/+/7419
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The original document from Jedec does not report the entry for
"21 NXP (Philips)", replaced by "c". It's clearly a typo.
Keep the line from JEP106BF.01 for "NXP (Philips)".
Change-Id: I30215c4ff08d5f112305cde6ab7a3176cdcef948
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7727
Tested-by: jenkins
On Windows, isatty() can return any non-zero value if it's an interactive
device. Which diverges from the ARM semihosting specification. This patch
introduces a fix to make the SYS_ISTTY operation conform to spec.
Change-Id: I9bc4f3cb82370812825d52419851910b3e3f35cc
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7725
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
The old implementation of gdb socket error handling
in the gdb_get_char_inner() differs between Windows and *nix
platforms. This patch simplifies it by using an existing
function log_socket_error() which handles most of the platform
specific things. It also provides better error messages.
Change-Id: Iec871c4965b116dc7cfb03c3565bab66c8b41958
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7724
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added debug prints to show what is the target debug reason. Also added
debug print for Ctrl-C response. This is useful for troubleshooting and
log analysis.
Change-Id: I055936257d989efe7255656198a8d73a367fcd15
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7720
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
These functions used to exist but don't anymore. (Pointed out in #863)
Change-Id: Iac6b5edd320bdff7628a788861e332f956dcd93d
Signed-off-by: Tim Newsome <tim@sifive.com>
Previously, progbuf execution did not flush or invalidate the register cache which could lead to incorrect behavior. This patch fixes it as well as refactors few sore points in the code related to it.
Change-Id: I353b931ca70a1828d4a9cc512aead00441730875
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Otherwise we may end up modifying DCSR of a different hart than
intended.
Change-Id: I39bde21a1444623ed150f2b3d504b9318b9d6191
Signed-off-by: Tim Newsome <tim@sifive.com>
This change adds the extensa sample target and board configurations.
it removes the obsoleted vd_xtensa_jtag.cfg from targets.
Change-Id: I9d4d25abde46c0b15e5211a973012447872cb405
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7723
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This change implements the predefined type tap_state instead of generic
uint8_t in the driver
Change-Id: I3478e8d7b40b961f3ba77711179016cdcc35cd32
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7722
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This change fixes endianness support in the driver.
Change-Id: Ida360bb58e988cea0a66fdc79e1610b528846fc4
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7721
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang reports that 3rd function call argument is an uninitialized value
file esp32_apptrace.c line:1270
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I73e254d4eb0c6b3152229717d8827d334784ab92
Reviewed-on: https://review.openocd.org/c/openocd/+/7719
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Initialize clocks to max speed and setup SDRAM. NAND support is still
incomplete. Originally found at:
elinux.org/index.php?title=Calao_Atmel_AT91_development_board&oldid=73933
Updated the code from 2011 and improved it a bit.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I83474e07c8de8cc3b5d058029551935549693ef9
Reviewed-on: https://review.openocd.org/c/openocd/+/7578
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang is unable to fully track the content of the array
write_buffer[] and incorrectly complains that it could contain
some uninitialized value.
To help clang to track the execution flow, rewrite the handling of
the buffer by using simpler indexing and by moving away cmd_byte
from the first buffer's element to the variable cmd_byte.
While there:
- fix the error codes returned while parsing the command line and
- use directly command_print_sameline() instead of passing through
intermediate buffers.
Change-Id: I1969e896887ea3a4abebee057cc04c03005fa57c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7718
Tested-by: jenkins
Clang 15.0.7 complains about snprintf output truncation due to
output between 13 and 22 bytes into a destination of size 20.
Increase the size of the buffer.
Change-Id: I0369255ca1bc02a0cf494f765e91a608c960a0d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7717
Tested-by: jenkins
Value in the 'dscsr' variable is garbage until the DAP queue is run.
Postpone evaluation of the 'secure_state' variable. Reading the
core registers in between will execute the DAP queue.
Change-Id: I44959e882dbafb1b9779e813c3d13f3b3dbcd47f
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7693
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The registers pauth_dmask and pauth_cmask are not accessible in
AARCH32 mode. Tagging them as 'hidden' is not enough and triggers
error:
Failed to read pauth_dmask register
while halting the core.
Tag the pauth registers as not existing, unless required by user.
Note: for non existing registers there should be no need to
allocate their register cache. Let's keep this for a further
improvement.
Change-Id: Iaa0d006a3d8ee611ee93333ed49a8615a6c94276
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: d0436b0cda ("armv8: Add support of pointer authentication")
Reviewed-on: https://review.openocd.org/c/openocd/+/7712
Tested-by: jenkins
Reviewed-by: Koudai Iwahori <koudai@google.com>
Register access on running target should fail if mstatus needs to be
modified.
Change-Id: Iec8e8d514ef2f5ca42606a5534cce55aaaa99180
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Marek Vrbka
Tim Newsome
Mark Zhuang
eolson
Chao Du
Evgeniy Naydanov
Lorenz Brun
Antonio Borneo
iosabi
Jacek Wuwer
Erhan Kurubas
Wolfram Sang
Dominik Wernberger
Bohdan Tymkiv