This commit is adapted from [1].
[1] https://review.openocd.org/c/openocd/+/4999
Signed-off-by: Michael Walle <michael.walle@kontron.com>
Signed-off-by: Heiko Thiery <heiko.thiery@kontron.com>
[ adapted to use common configuration ]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9a428371694e7864e03055b8de18a55a7843b8c2
Reviewed-on: https://review.openocd.org/c/openocd/+/6977
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1028A is similar to the LS1088A, except that it has 2 CPUs (and
different ethernet capabilities). From a JTAG perspective, all that's
different is the number of CPUs and the TAPID.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Iba3a0ecfbf82cfcfeb7eea42d52121c3b9dc93a2
Reviewed-on: https://review.openocd.org/c/openocd/+/6976
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Several Layerscape processors (LS1088A, LS2088A, LS2160A, and LS1028A)
share a common architecture. Break out the common setup from the LS1088
config in preparation for adding the LS1028A. There's no official name
for this series of processors, but NXP refers to them as "chassis
generation 3" in U-Boot, so we'll go with that too.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ic6f89f95c678101f54579bcaa5d79c5b67ddf50a
Reviewed-on: https://review.openocd.org/c/openocd/+/6975
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This command allows users to set base working directory for the
semihosting I/O operations.Default is the current OpenOCD directory.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I80c5979e4c96d66cccdd12cc6fcd5f353e5c6b4d
Reviewed-on: https://review.openocd.org/c/openocd/+/6888
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added support for the new Renesas RISC-V
device: RZ/Five
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Change-Id: Id8ba29b83528c0bfe4f9b4ed21b0151a6e853bd7
Reviewed-on: https://review.openocd.org/c/openocd/+/6974
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Added support for two new devices: RZ/G2LC and RZ/G2UL
Change-Id: Iec6ba88c1d279f50808b060343b45c796bbfdbfc
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6972
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes "variable set but not used" errors.
Tested with Homebrew clang version 13.0.1
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ia90baf5b4857db2b5569ebe6adbbb832de772aad
Reviewed-on: https://review.openocd.org/c/openocd/+/6971
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Removes Warning: line 6482, column 12
1st function call argument is an uninitialized value
Use target ptr directly as checked in previous lines instead of
dereferencing head->target
Change-Id: I6804b776fd493af71f3098d702f9cdc7acb50151
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6970
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
First time contributors surprisingly often write "topic:"
instead of "the main part or subsystem the patch touches" as requested
in patchguide.html
To prevent them doing so:
Use longer self-explaing "specify touched area" instead of "topic"
Give some examples in addition to recommended looking at "git log"
Change-Id: I1c307b460d7a79ba3c9918af8dbc9e9f827e1fb9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6683
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tigard[1] is an FT2232H-based development tool designed for ease of use
with many different protocols and targets. It includes a JTAG header
wired to channel B, with labeled pins for the four required signals as
well as nTRST and nSRST, which are connected through an output buffer to
BDBUS4 and BDBUS5 respectively.
Add an interface config for Tigard. I wrote it by referencing the Tigard
schematic and tested it by debugging a couple of RISC-V development
boards.
[1] https://github.com/tigard-tools/tigard
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Change-Id: I34df9f72538ba1e40ad53b568c9cdca96ae4b082
Reviewed-on: https://review.openocd.org/c/openocd/+/6952
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While cross-compiling OpenOCD the generated script is not named
"libtool" anymore, but e.g. "arm-linux-gnueabi-libtool".
Ignore all the possible variants "*-libtool".
Change-Id: I7a0dade992dbc13f977610bd4a78f8a4783b0146
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6960
Tested-by: jenkins
Incorrect validation prevented GPIO0 from controlling the direction of
the SWDIO buffer or operating TRST/SRST.
Have all GPIO number validation checks performed by is_gpio_valid().
Change-Id: Ib8fb704ab588a618ac41c111f6168d658891d92c
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It is a common requirement to automatically execute some command
after "init".
This can be achieved, either in scripts or through OpenOCD command
line, by explicitly calling "init" followed by the commands.
But this approach fails if the request for post-init commands is
spread across configuration files; only one of the files can split
pre-init and post-init status by calling "init".
The common workaround is to "rename" the command "init" and
replace it with a TCL proc that calls the original "init" and the
post-init commands. E.g. in Zephyr script [1].
To simplify and formalize the post-init execution, use a TCL list
that contains the list of commands to be executed. Every script
can contribute adding new commands, e.g. using "lappend".
In the same way, formalize the pre-shutdown execution with a TCL
list of user commands to be executed before OpenOCD exit.
Document them and add trivial examples.
Drop from documentation the suggestion to rename "shutdown".
Change-Id: I9464fb40ccede3e7760d425873adca363b49a64f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Link: [1] https://github.com/zephyrproject-rtos/zephyr/blob/zephyr-v2.7.1/boards/arm/nucleo_h743zi/support/openocd.cfg#L15
Reviewed-on: https://review.openocd.org/c/openocd/+/6851
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function target_type::deassert_reset() is called for every
target after reset is deasserted. If the target fails to get
halted, we log a warning and issue a halt request for the target
itself.
Current code calls the generic target_halt() that:
- extends the halt to all the targets in the SMP node;
- waits for targets to halt.
This breaks the logic of running target_type::deassert_reset()
per target. Plus, waiting for targets to halt delays the call of
target_type::deassert_reset() for the next targets.
Replace the call to target_halt() with the aarch64 specific
function to halt the single target. Pass the parameter HALT_LAZY
to prevent the wait for target halted.
Similar solution is already implemented for cortex_a.
Change-Id: I446dc03cb91524c6d388db485bc2388177af77b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6947
Tested-by: jenkins
Arm documentation does not explicitly report the order of the two
32bit words that compose the 64bit value. But both ADIv5 and ADIv6
specify that only little-endian is supported (ADIv5.2 obsoletes
the big-endian support). This change reads the 64bit value in
little-endian.
Detect the 64bit content and use it.
Change-Id: I723ec099c7e8c70c1f9a568e32ea867fcbf1f1db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6465
Tested-by: jenkins
With the generic function for ROM table walk-through, reimplement
dap_lookup_cs_component().
Catch the code CORESIGHT_COMPONENT_FOUND and halt the search.
While there, drop two macros in arm_coresight.h, now unused.
Change-Id: I589ef7ae8a651d0c422ce7d0b4ed913713a8217e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6824
Tested-by: jenkins
Simplify the code in cortex_a and aarch64 by moving the call to
dap_get_debugbase() inside dap_lookup_cs_component().
This has the further effects:
- dap_get_debugbase() is not referenced outside arm_adi_v5.c and
becomes static;
- dap_lookup_cs_component() looses one parameter;
- the coreid parameter 'idx' is passed as value;
- the caller in aarch64 don't have and don't print the irrelevant
value of AP register APID;
- fixes the debug message in the caller in aarch64 to print the
coreid value instead of always zero.
Change-Id: Ic7f0f643fdf067c059c8f2455a02ff18a3fed054
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6823
Tested-by: jenkins
Now all the actions (build command output) of command "dap info"
are decoupled from the ROM walk-through.
Pass the actions as a generic parameter to ROM walk-through code.
Put as private data every information that is only required by the
actions and not by the ROM walk-through.
Change-Id: I3b6ad112ea21296458c94aebbf91bf65bf6657a7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6822
Tested-by: jenkins
This change only targets the output of rtp_rom_loop().
Change-Id: If9ac013798923428c3b897a969887e98b6935a2b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6821
Tested-by: jenkins
This change only targets the output of rtp_cs_component().
To easily propagate the coordinates of the CoreSight component,
add them in the struct that holds the register values.
While there, define a macro for the max depth of ROM tables.
Change-Id: I75e5ef4f9419da3192123aebcd61471c2af9374f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6820
Tested-by: jenkins
In OpenOCD arm_adi_v5 we have already two implementations of code
for parsing the ADIv5 ROM table:
- in the commands "dap info" and "$dap_name info";
- in the function dap_lookup_cs_component().
Adding support for ADIv6 requires extending both implementations.
Moreover, current code does not handle few aspects of the ROM
parsing, e.g. the "Power Domain IDs".
To add such extensions both implementations should be touched.
I plan to add a command to parses (again) the ROM table and dump a
simple prototype of a configuration script for the target, useful
while analysing a new target.
Keeping aligned all these implementation would be too complex.
With focus to "dap info" command, decouple the part of code to
walk-through the ROM table from the code that creates the command
output.
The idea is to keep a single implementation for the walk-through
code, while parametrizing the output code to handle the generation
of a configuration script or the result of the function
dap_lookup_cs_component().
This change only targets the output of MEM-AP header
Further changes will target other parts of the code.
While there, add a message if MEM-AP is not accessible.
Change-Id: I112f637edfdb8688afb4e631297f6536da9604f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6819
Tested-by: jenkins
ARM IHI0031F "Arm Debug Interface Architecture Specification"
chapter C2.6.1 "BASE, Debug Base Address register" reports:
A debugger must handle the following situations as
non-fatal errors:
- ...
- An entry in the ROM Table points to a faulting location.
- ...
Typically, a debugger issues a warning if it encounters
one of these situations. However, Arm recommends that it
continues operating. An example of an implementation that
might cause errors of this type is a system with static
base address or ROM Table entries that enable entire
subsystems to be disabled, for example by a tie-off input,
packaging choice, fuse, or similar.
Don't halt ROM table parsing if one entry causes an error; log the
error condition and continue to next entry.
Not sure if we have to send an ABORT before continuing.
Change-Id: I94fdb5b175bfb07dde378149421582b7e7cd5b09
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6818
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
As Class 0x1 ROM table, also Class 0x9 ROM tables encodes a flag
for system memory access.
Detect the flag in rtp_cs_component() and dump the same message
for both type of ROM tables.
Extend rtp_read_cs_regs() to read ARM_CS_C9_DEVID.
Change-Id: Ic85d1ea068ed706ceedfd65076ff4c96d04e9792
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6817
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
During ROM table parsing, each ROM table entry points to a
CoreSight component that can, in turn, be another ROM table.
Split the specific code for ROM table handling from the generic
CoreSight code.
Log an error if a ROM table entry cannot be read.
Change-Id: I5ad106a99b9c21ddb48b5b162ae87101e4f49878
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6816
Tested-by: jenkins
Rework dap_read_part_id() while preparing for reorganizing the
'ROM Table Parsing' (RTP):
- rename it with 'rtp' prefix;
- extends it to read other CoreSight registers, thus improving the
overall speed by queuing more reads;
- reduce the list of arguments by using a struct;
- reorder the reads by increasing offset, potentially gaining
speed using MEM_AP_REG_BDx and/or auto-increment;
- log a debug message in case of read error.
Change-Id: I6544ac7740b808a6c0fbacf97ac00b97f5bd3832
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6815
Tested-by: jenkins
ADI v5.1 and v6.0 permit the definition of CoreSight components (class 9
ROM entries).
dap_rom_display() is refactored a bit such that we always end up with
attempting to parse the ROM contents using the appropriate upper limit
for class 1 and 9 ROM types.
Change-Id: I4ba497b3807f1f11f06186eb6e61959ea3540c59
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6359
Tested-by: jenkins
Use the list of values from ARM IHI0029E to decode and print the
Device Architecture register.
Add attribute 'unused' to the function, not used yet.
Change-Id: I7b1dd204bd1db671578c588372b667e23611876c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6463
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
In case of AP not responding, e.g. not clocked, the first WAIT
reply is logged as:
DAP transaction stalled (WAIT) - slowing down
then OpenOCD retries the transaction few times, until it timeouts.
At each retry it prints the message:
DAP transaction stalled during replay (WAIT) - resending
Depending on JTAG speed and transport latency, the amount of log
messages can be quite annoying and not relevant.
The last printed line is at timeout:
Timeout during WAIT recovery
Reduce the verbosity.
Change-Id: I5a7a337527c98b2450de59066b13713511c2894f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6814
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Right now it has a single use but it will soon be used more.
Change-Id: I9a819c65df467fc859e4b5251035a17ed33daa35
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6813
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
since commit 12d1ad0c75 : update capstone include path ...
the generated capstone.pc is not working
so fix the includedir in capstone.pc to get github action working
Change-Id: I7767e181a74c73a7514eeb6293cd556a794dbfe9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6969
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Append lacking e to word Note
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Change-Id: Ibd40a2f93d11cf1945361f0c46329b88963d6826
Reviewed-on: https://review.openocd.org/c/openocd/+/6963
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In jimtcl 0.80 the prototype of Jim_DictPairs() has changed.
The only code in OpenOCD that uses Jim_DictPairs() has been merged
recently and it only uses the current jimtcl syntax.
To allow compiling OpenOCD master branch with older versions of
jimtcl, detect the version of jimtcl and use the appropriate
syntax.
Change-Id: I6fc78303b6a4db064a97f326c46119f4568e88f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: dullfire@yahoo.com
Reviewed-on: https://review.openocd.org/c/openocd/+/6948
Tested-by: jenkins
Added bluenrg-lps support
Added file for the board steval-idb012v1
Fixed size_info information using a mask
Changed the if condition in bluenrg-x.cfg to be valid only for bluenrg-1 and bluenrg-2
Signed-off-by: Salvatore Giorgio PECORINO <salvatore-giorgio.pecorino@st.com>
Change-Id: Ic0777ec0811ee6fac7d5e1d065c4629e47d84a1f
Reviewed-on: https://review.openocd.org/c/openocd/+/6928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 5ebb1bdea1 ("server/gdb: fix return of gdb remote monitor
command") replaces the call to command_run_line() with call to
Jim_EvalObj() but does not properly set the "context".
In multi-target environment, his can cause the erroneously
execution of the command on the wrong target.
Copy from the code in command_run_line() the proper setup before
executing Jim_EvalObj().
Change-Id: I56738c80779082ca146a06c01bc30e28bc835fd3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Bohdan Tymkiv <bohdan200@gmail.com>
Fixes: 5ebb1bdea1 ("server/gdb: fix return of gdb remote monitor command")
Reviewed-on: https://review.openocd.org/c/openocd/+/6966
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
The deprecation was already in the documentation since v0.11.0
through commit 85ba2dc4c6 ("rtos/hwthread: add hardware-thread
pseudo rtos") but OpenOCD was not informing the user printing a
runtime message.
Remove the deprecated method from the documentation and print a
deprecated message at runtime.
There is no reliable way to print the same message in GDB console,
so we have to rely on user noticing it in the OpenOCD log.
Target is to remove the functionality after v0.12.0.
Change-Id: Idd2d9e3b6eccc92dcf0432c3c7de2f8a0fcabe9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6862
Tested-by: jenkins
on macos (homebrew base) `pkg-config --cflags capstone` output with
`-I/opt/homebrew/Cellar/capstone/4.0.2/include/capstone`
gcc not find headers on parent "include" path,
causes build error `fatal error: 'capstone/capstone.h' file not found`
it's ok to change to <capstone.h> for all platforms.
Signed-off-by: fatalc <cnfatal@gmail.com>
Change-Id: Ia2e2058024d4fc1a57a8b4ea847c664d74f67efb
Reviewed-on: https://review.openocd.org/c/openocd/+/6946
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Handle JIM_CONTINUE return value of adiv5_jim_mem_ap_spot_configure(),
otherwise OpenOCD silently quits when an unknown option is provided.
Change-Id: I9b1351c0911e74999d8dd1260ede9760088510d7
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6944
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct ordering is required to prevent two outputs connected
together.
Change-Id: I634a9ca7e0ccf337d1723011b8aee1f2d81efbcf
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6937
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The SWDIO buffer requires a direction pin to select input or output
direction. Output is selected by a high logic level (matches
bcm2835gpio driver).
Change-Id: I240cb99a5dfea08121bb33d4b5e2108ce7597468
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to GigaDevice user manuals the devices have OBRLD bit in FMC_CTL
register which is functionally compatible with OBL_LAUNCH @ FLASH_CR
of STM32 counterparts.
Change-Id: I84d231b38815fcb6452fd73b9153b269cce3b737
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6759
Tested-by: jenkins
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
The flash is compatible with stm32f1x, reuse the driver.
Extend the size of work area to RAM size of the smallest device.
Stop watchdogs before flash programming.
Change-Id: I67a7654a6e196f9d4b2409edaa7990c53334437e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6711
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The device has compatible flash macro with STM32F1 family, reuse
stm32f1x driver code.
Detect non-ARM target - for simplicy test target type name 'riscv'
and the address has 32 bits.
In case of RISC-V CPU use simple chunked write algo - async algo
cannot be used as the core implemented in this device doesn't
allow memory access while running.
Change-Id: Ie3886fbd8573652691f91a02335812a7300689f7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6704
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Zephyr plan to remove openocd specific symbols in favour
of more generic one.
These generic symbols has been introduced in Zephyr 2.6.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: I89418c9c378fb8b8baa29763fc6f1b6e652dc7ef
Reviewed-on: https://review.openocd.org/c/openocd/+/6844
Tested-by: jenkins
Reviewed-by: Stephanos Ioannidis <root@stephanos.io>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixed the reading of p_flags in ELF64 segment headers - that field
is 64 bits wide.
Change-Id: I053ca57d36efb54b7c638484acd6c7a2fbcbd05a
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6927
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Sean Anderson
Erhan Kurubas
micbis
Tomas Vanek
Thomas Hebb
Steve Marple
Antonio Borneo
Florian Fainelli
Tarek BOCHKATI
Piotr Kasprzyk
Salvatore Giorgio PECORINO
jihongbin
fatalc
Marc Schink
Julien Massot
Jan Matyas