This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Provide $defines for more of the signals involved in the
Luminary ICDI hardware, and comment some of what's going on.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use addition for offsetting, not masking. Shorten some lines.
Make "component_start" print-only (unused otherwise; don't save).
Still doesn't resolve the issue where multiple components
are wrongly displaying as NVICs on some Cortex-M3 parts because
many PIDs appear to be zeroes ... maybe adapter related??
Signed-off-by: David Brownell <db@helium.(none)>
waiting for ZY1000 fifo to idle is now queued as
an asynchronous command. This radically improves
performance when waitIdle() is interspersed with
writes as no readback is required over TCP/IP.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Mask the upper bits after 32-bit reads.
Alsoo revert the ugly changes to use PRIx32; just cast to unsized
integers when printing (two chars not eight).
Signed-off-by: David Brownell <db@helium.(none)>
This reverts the incorrect change made to the arm9 cmd group in commit
d1eca9a74c.
The code now matches the docs and the release notes.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Bugfix and simplify legacy jtag-only defaulting
* Make "dummy" declare its jtag-only nature
* likewise update ft2232
* warn if selection is _required_ (multi-transport adapters),
fixes the "only ft2232 works" bug for at least dummy, with
other drivers going the "legacy" path (submit patches).
Signed-off-by: David Brownell <db@helium.(none)>
String compare against addresses in range 0 or so due
to not checking if there was an active session first.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Classic manifestation of weakness of dangling {
formatting :-) Hard to spot these sort of mistakes visually.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Commit 93f2afa45f dropped the sentinel off the end
of the command_registrants[] array. The loop immediately
following the initialization will walk right off the end.
Signed-off-by: Stacey Sheldon <stac@solidgoldbomb.org>
This adds the guts of a transport framework with initialization,
which should work with current JTAG-only configurations (tested
with FT2232).
Each debug adapter can declare the transports it supports, and
exactly one transport is initialized. (with its commands) in
any given OpenOCD session.
* Define a new "struct transport with init hooks and a few
"transport" subcommands to support it:
"list" ... list the transports configured (just "jtag" for now)
"select" ... makes the debug session use that transport
"init" ... initializes the selected transport (internal)
* "interface_transports" ... declares transports the current interface
can support. (Some will do this from C code instead, when there are
no hardware versioning (or other) issues to prevent it.
Plus some FT2232 tweaks, including a few to streamline upcoming
support for an SWD transport (initially for Luminary adapters).
Eventually src/jtag should probably become src/transport, moving
jtag-specific stuff to transport/jtag.
Signed-off-by: David Brownell <db@helium.(none)>
Revert change made in commit dd88b461da.
Caused segfaults when using ftdi driver under win32.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The code did not transfer the last word in no-ack transfers.
The strange thing is that this did not lead to any
observable errors.
This gaffe was introduced in commit 1f5883ea56
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Review allocation of error numbers in openocd
to avoid overlap.
Put brackets around negative numbers to avoid
issues during macro expansion.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory read/writes to virtual memory, requires that the CPU is
halted.
Use 'phys' option to write to memory while target is running.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when locking the debug access fails on the first try, it's a
bit noisy, so print out message that it succeeded on second try.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add "static" qualifier to private functions.
Move duplicated global declarations from "target/avrt.c"
and "nor/avrf.c" to "target/avrt.h".
Remove unused declarations form "nor/avrf.c".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add "static" qualifier to private functions.
Remove private prototypes from include file.
Remove empty definition of JIM_STATIC.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This fn is an implementation detail of jtag_execute_queue()
that is not to be exposed externally.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
normal code should not call jtag_get_error(), but rather check
the return code from jtag_execute_queue().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When an interactive command fails, the Jim stack trace prints references to
the line in "command.c" where the interpreter was invoked. Since that
location has no relation to the actual command that failed, the information
serves only to add confusion.
By not adding the useless source info to Jim the noise can be reduced,
while still printing a useful trace for nested commands.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add "static" qualifier to private functions.
Function Jim_InterpolateTokens() is private, but has not
been changed to "static".
This function is called only once, so compiler inlines it.
After inline, there is a warning for variable uninitialized.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
(error: declaration of ‘stat’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/sys/stat.h:279: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
(error: declaration of ‘byte’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:50: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
(error: declaration of ‘pHDev’ shadows a global declaration; ../../../../src/jtag/drivers/rlink.c:102: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
in jim.c (error: declaration of ‘boolean’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:52: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
copy & paste error + added FIFO throttling to work around
lockup bug in FPGA.
The arm11 optimisation was introduced post v0.4.0, so this
is not a regression compared to previous release.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Helper ./src/helper/membuf.c is only used in at91sam3.c
1) Replace membuf with LOG_*
2) The original code in sam3_GetDetails() invalidates
all the buffered output of sam3_GetInfo(). The new
code skips sam3_GetInfo() if its output should not
be printed.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I think this fixed an error message where the error
message would show the *previous* uc code rather than
the current unsupported uc code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when the verify failed, it didn't return an error,
which breaks e.g. tcl scripts that rely on this for
exceptions to work.
Found by -Wshadow
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this batch of fixes should be pretty straightforward
rename of 'index' and an 'i' local variable shadowing.
'index' conflicts with a global name.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
found by code inspection. There are many other places in
CFI where LOG_ERROR() should be called similarly...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when a write/unlock/erase failed during write_image, then
an error was not propagated back up so e.g. flash write
image from tcl scripts would not throw an exception.
Also flash filling speed was printed even when the
operation failed. Output is now less confusing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
failure to write to memory was not propagated.
This is an interesting case of broken error handling:
with exceptions we wouldn't have had this at all,
and I also wonder if there is a GCC option to warn
about these kinds of potential bugs.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Parameter "type" of function armv4_5_mmu_translate_va()
is now not used.
Remove the parameter and the "enum" listing its values.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function armv4_5_mmu_translate_va() now properly signals
errors in the return value.
Remove former error handling by setting variable "type" to
value "-1".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function arm920t_write_memory() default return value
should be ERROR_OK.
All cases of local errors are handled immediately and
not further propagated.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 0538081246
introduces a compile time warning:
arm920t.c: In function ‘arm920t_write_memory’:
arm920t.c:567: warning: ‘retval’ may be used uninitialized in this function
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
any read/write operation to memory can fail.
block write algorithm error propagation was broken
in that it would continue after an error was reported
writing data to ram or the algorithm failing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
JTAG_MOVESTATE is misleading, this cmd is only used
for reset.
JTAG_PATHMOVE should be used otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hello,
"stm32x mass_erase" return ERROR_OK even if something goes wrong.
Here is a summary of changes :
* in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error
detected in FLASH_SR register;
* in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the
returned value of stm32x_mass_erase().
I don't know if there is reason to always return ERROR_OK ?
Gaëtan
ETM analyze produced no output when the trace buffer was empty.
This patch provides users with a clue.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Every time command "flash probe #" is executed, memory
structures are re-allocated without preventive free()
of former areas, causing memory leak.
Also, memory allocation does not check return value,
determining segmentation fault in case of out of memory.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
We request a id register read at the end of ahbap_debugport_init
but we never actually run the queue. In some cases this causes a
segfault.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
This second half of the patch is proposed to clean up some GDB keep alive
issues on arm7_9 targets that start up with very slow clocks. If an attempt
is made to write to key registers on the processor with a slow jtag speed,
GDB timeout warnings appear on the console (at least mine) when "reset halt"
or "reset init" commands are issued from the gdb client:
*** BEFORE PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1026). Workaround: increase "set remotetimeout" in GDB
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1027). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1004). Workaround: increase "set remotetimeout" in GDB
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
I added additional keep alive steps in areas that troubleshooting revealed
were causing problems. I only did this however for non-fast write memory
accesses. I don't think most people would be using fast memory accesses to
write to memory when the jtag and system clocks are slow anyway.
If you disagree with my feeling, think there is a more elegant way to handle
the problem, or think the patch will cause other unforeseen problems with
other targets, let me know. As you can see below, the patch does eliminate
the problem on my development station and I suspect that it will benefit
others.
*** AFTER PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
Gary Carlson
Gary Carlson, MSEE
Principal Engineer
Carlson-Minot Inc.
tcl "puts" didn't work because the logging code sensored strings
that did not include a '\n'. The correct thing is to sensor
empty strings, which are used to keep gdb connection alive.
The tcl "puts" code broke apart strings which do contain '\n' in
order to implement the -nonewline argument, which is how it
got hurt by the bug in log.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Page reads using hwecc4_infix layout segfaulted for check_bad_blocks because
the read assumed a valid data buffer, which check_bad_blocks does not use
(it only passes a 6 byte buffer for the start of OOB).
This version copes with undersized or missing data or oob buffers and uses
random read commands within the page to skip unwanted areas of data/OOB for
speed.
NOTE: Running check_bad_blocks with this layout will be reading infix
OOB locations, not manufacturer bad block markers. This means that if you
check blocks written in infix layout they will appear good, but manufacturer-
marked bad blocks may also appear good.
If you want to scan for manufactuer-marked bad blocks, you need to enable
raw_access before running check_bad_blocks, or use the non-infix layout.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
CC: David Brownell <dbrownell@users.sourceforge.net>
nand_build_bbt() was ignoring the return value from nand_read_page() and
blindly continuing.
It now passes the return value up to the caller if the read fails.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Change download rate messages about kibibytes from "kb/s" to "KiB/s" units.
See: http://en.wikipedia.org/wiki/Data_rate_units
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Remove few LOG_DEBUG() messages, together with code and
variables required to build such messages.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final step to force bus_width size during CFI flash
read.
Added CFI specific implementation cfi_read() that uses
only accesses at bus_width size.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
During cfi_write(), head and tail of destination area
could be not aligned to bus_width.
Since write operation must be at bus_width size, source
buffer size is extended and buffer padded with current
values read from flash.
Force using bus_width to read current value from flash.
Do not use cfi_add_byte() anymore, to allow removing this
function later on.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
NOR flash structure requires each access to be bus_width wide.
Fix read of flash ID accordingly to rule above.
Add case (chip_width == 4), allowed by CFI spec and coherent
with current value of CFI_MAX_CHIP_WIDTH but currently not
used by any target.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Since NOR flash devices does not handle "byte enable lanes",
each read/write access involves the whole "chip_width".
When multiple devices are in parallel, usually all chips are
enabled during each access.
All such cases are compatible with flash accesses at
"bus_width" size.
Access at "bus_width" size is mandatory for write access to
avoid transferring of garbage values to flash.
During read access the flash controller should take care,
and discard unneeded bytes. Anyway, it is good practice to
use "bus_width" size also for read.
Every memory access that does not respect "bus_width" size
is marked with a "FIXME" comment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Review and simplify computation of bufferwsize.
Add comments about variables' meaning.
The same code is present 3 times in the file.
Current patch updates all the 3 instances.
Step 1)
Replace "switch(bank->chip_width) {...}".
Illegal values of bank->chip_width are already dropped.
For legal values, the code is equivalent to:
bufferwsize = buffersize / bank->chip_width;
Step 2)
The above code replacement plus the following line:
bufferwsize /= (bank->bus_width / bank->chip_width);
is merged in a single formula:
bufferwsize = (buffersize / bank->chip_width) /
(bank->bus_width / bank->chip_width);
and simplified as:
bufferwsize = buffersize / bank->bus_width;
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Arguments chip_width and bus_width of command "flash bank" are
not fully checked.
While bus_width is later on redundantly checked in several other
parts (e.g. in cfi_command_val()) and generates run-time error,
chip_width is never checked, nor related to actual bus_width
value.
Added check to avoid:
- (chip_width == 0), that would mean no memory chip at all,
avoiding also division by zero e.g. in cfi_get_u8();
- (bus_width == 0), that would mean no bus at all;
- unsupported cases of chip_width or bus_width value not power
of 2;
- unsupported case of chip width wider than bus.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Last block was being skipped, fix by changing the loop test from "<" to "<="
First block argument was ignored, always started from block 0 (and counted
the wrong blocks as bad if first was nonzero). Now we use it.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The last_block argument to nand_erase() is checked against nand->num_blocks,
but the highest valid block number is (total - 1), the test for invalid should
be ">=" rather than ">".
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
flash cmds can now be passed either the bank name or the bank number.
For example.
flash info stm32.flash
flash info 0
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Hi,
This is my first post to the list. First, I would like to thank
everyone for their work on OpenOCD, it is a great tool to work with. I
have been using it to debug code on hardware for the Rockbox project
(www.rockbox.org).
The target that I primarily work with has a Spansion/Fujitsu NOR flash
(MBM29SL800TE). I attached a patch that adds support for this flash. I
hope it can be included in the main repository. If there is something
that needs to be changed with the patch before inclusion please let me
know.
-Karl Kurbjun
The ST/Numonix M29W128G has an issue when a 0xff cmd is sent,
it cause an internal undefined state. The workaround according
to the Numonyx is to send another 0xf0 reset cmd
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
c->sin.sin_port does not contain a valid port number so just use
service->port as this is always correct.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
There are a million reasons why cached protection state might
be stale: power cycling of target, reset, code executing on
the target, etc.
The "flash protect_check" command is now gone. This is *always*
executed when running a "flash info".
As a bonus for more a more robust approach, lots of code could
be deleted.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
No segmentationfault when sending commands to tcl-server.
modified: src/server/server.c
modified: src/server/tcl_server.c
modified: src/server/tcl_server.h
Various commands, e.g. "arm mcr xxxx" would fail if invoked upon startup
since it there was no command context defined for the jim interpreter
in that case.
A Jim interpreter is now associated with a command context(telnet,
gdb server's) or the default global command context.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove/fix lots of bugs in handling of non-contigious sections
and out of order sections.
Fix a gaffe introduced in previous commit to src/flash/nor/core.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove bogus error messages when trying to allocate a
large chunk of target memory and then falling back to
a smaller one.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
target memory allocation can be implemented not to show
bogus error messages.
E.g. when trying a big allocation first and then a
smaller one if that fails.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
make wait for srst deassert more long latency friendly
(JTAG over TCP/IP), print actual time if it was more than
1ms.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The current timeout for STM32 flash block erase and flash mass erase is
10 (ms), which is too tight, and fails around 50% of the time for me.
The data sheet for STM32F107VC specifies a maximum erase time of 40 ms
(for both operations).
I'd also consider it a bug that the code does not detect a timeout, but
just assumes that the operation has completed. The attached patch does
not address this bug.
The attached patch increases the timeouts from 10 to 100 ms. Please apply.
/Tobias
Fix a bug where write_image would fail if the sections
in the image were not in ascending order. This has previously
been fixed in gdb load.
Solved by sorting the image sections before running flash
write_image erase unlock foo.elf.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this is done for unlocking and it is a simple omission that
it wasn't done for sectors.
The unnerving thing is that nobody has complained about this
until now....
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Spencer Oliver
Øyvind Harboe
David Brownell
sb-sf
Stacey Sheldon
Marc Pignat
Olaf Lüke
Antonio Borneo
Edgar Grimberg
Andreas Fritiofson
Freddie Chopin
Thomas Koeller
gcembed
Jon Povey
Gary Carlson
Jun Ma
Jun Ma
Karl Kurbjun
Matthias Bode
Tobias Ringström