End of line comments fixed with ';' before '#'.
Added few additional 'space' to keep indentation in
multi-line comments.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Clarify that ICDI is the generic logic, but this config is
for the JTAG-only (no-SWD) mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds definition file for the Voipac VPACLink JTAG adaptor. The
adaptor is combined JTAG/UART device.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Add PARPORTADDR tcl variable making it easier to
change parallel port address in scripts.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it
out of the "jtag" command group ... it needs to be used with non-JTAG
transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_khz" as "adapter_khz", and move it out of the "jtag"
command group ... it needs to be used with non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year. (We may want to
update it to include a nag message too.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This includes a driver and matching config file. This support needs to be
enabled through the initial "configure" (use "--enable-buspirate").
Signed-off-by: Michal Demin <michaldemin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Added interface config file for JTAG/RS232 debug board originally
integrated to Neo 1973 and Neo FreeRunner phones.
Adapter was tested with i.MX31, S3C2410 and AT91SAM9260 processors.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
The "parport_port" commands generally don't *require* a port_number;
they're of the "apply any parameter, then print result" variety. Update
the User's Guide accordingly.
Some of those commands are intended to be write-once: parport_port,
and parport_cable. Say so.
Use proper EBNF for the parport_write_on_exit parameter.
Parport address 0xc8b8 is evidently mutant. Say so in the "parport.cfg"
file, to avoid breaking anyone with that mutant config. But update the
User's Guide to include a sane example for the LP2 port.
Finally document the "presto_serial" command.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The relevant cable config is already in OpenOCD, but not a config for
the JTAG adapter. I have tested with FlashLINK on ARM926.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's been about a year since these were deprecated and, in most
cases, removed. There's no point in carrying that documentation,
or backwards compatibility for "jtag_device" and "jtag_speed",
around forever. (Or a few remnants of obsolete code...)
Removed a few obsolete uses of "jtag_speed":
- The Calao stuff hasn't worked since July 2008. (Those Atmel
targets need to work with a 32KHz core clock after reset until
board-specific init-reset code sets up the PLL and enables a
faster JTAg clock.)
- Parport speed controls don't actually work (tops out at about
1 MHz on typical HW).
- In general, speed controls need to live in board.cfg files (or
sometimes target.cfg files), not interface.cfg ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add interface configs for two new high speed JTAG
adapters from Olimex. They need some other speed
related tweaks to work well at high speed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch includes partial support for these new JTAG adapters.
More complete support will require updates to the libftdi code,
for EEPROM access.
[dbrownell@users.sourceforge.net: fix whitespace, linelen, etc ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Ofrwarded from Ron, who's not subscribed.
----- Forwarded message from Ron <ron@debian.org> -----
From: Ron <ron@debian.org>
Date: Wed, 14 Oct 2009 04:50:17 +1030
To: wookey@debian.org
Subject: [PATCH] OpenRD board configuration
X-Spam-Status: No, score=-3.6 required=4.5 tests=BAYES_00,RCVD_IN_DNSWL_LOW
autolearn=ham version=3.2.5
This piggybacks on the 'sheevaplug' layout which uses the same Kirkwood SoC.
Signed-off-by: Ron Lee <ron@debian.org>
This patch adds support for the Luminary Micro LM3S9B90 target and
LM3S9B92 Evaluation Kit. These kits include a new ft2232 adapter, the
Luminary In-Circuit Debug Interface (ICDI) Board, so this is added as a
new ft2232 layout called "luminary_icdi".
git-svn-id: svn://svn.berlios.de/openocd/trunk@2429 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Move src/tcl to tcl/.
- Update top Makefile.am to use new path name.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1919 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Tormod Volden
Michael Trensch
Antonio Borneo
Piotr Esden-Tempski
David Brownell
Peter Stuge
Spencer Oliver
Marek Vasut
Michal Demin
Edgar Grimberg
Vladimir Zapolskiy
Catalin Patulea
mkdorg@users.sourceforge.net
Krzysztof Kajstura
Dimitar Dimitrov
Oleg Seiljus
Wookey
ntfreak
oharboe
zwelch