* WIP, rewrite of flash algorithm.
Just put all the flashing logic into the algorithm, instead of using an
intermediate format. This should reduce total data written while
flashing by about 9%, and also makes the code much simpler.
Change-Id: I807e60c8ab4f9f376cceaecdbbd10a2326be1c79
* New algorithm works.
Speeds up Arty flashing another 9%.
wrote 2228224 bytes from file /media/sf_tnewsome/SiFive/arty_images/arty.E21TraceFPGAEvaluationConfig.mcs in 86.784538s (25.074 KiB/s)
verified 2192012 bytes in 6.693336s (319.816 KiB/s)
8.66user 13.03system 1:33.91elapsed 23%CPU (0avgtext+0avgdata 12272maxresident)k
Change-Id: Ie55c5250d667251be141cb32b144bbcf3713fce4
* Fix whitespace.
Change-Id: I338d518fa11a108efb530ffe75a2030619457a0b
* Don't reserve so much stack space.
Also properly check XLEN in riscv_wrapper.S.
Change-Id: Ifa0301f3ea80f648fb8a6d6b6c8bf39f386fe4a6
* Cache program buffer writes.
Speeds up flash program by 3%, flash verify by 2%.
Change-Id: I19f8f44f560a1111fa8f4e4fc04ce6de3c94999a
* Remove nop from batch reads.
program @ 22.123 KiB/s, verify @ 47.654 KiB/s (up from program @ 20.287
KiB/s, verify @ 23.148 KiB/s originally).
Change-Id: I7ee19d967b1080336b0088d20e1fc30828afd935
* Use "algorithm" to compute CRC on RISC-V targets.
Use the C compiler to generate the algorithm code. It's better at
assembly than I am. We need separate RV32 and RV64 binaries to handle
shift instructions. I used the code from gdb (libiberty really) because
it returns the correct result. I'm not sure if the table is worth it
since we do have to save/download/restore more bytes now.
riscv_run_algorithm() now properly saves and reads back all registers
used for parameters. It also doesn't check final_pc if exit_point is 0.
Using gdb means I don't know the exact address where the code will end.
Small target.[ch] change to be able to run algorithms at 64-bit
addresses.
Flashing an arty board now:
```
wrote 2228224 bytes from file /media/sf_tnewsome/SiFive/arty_images/arty.E21TraceFPGAEvaluationConfig.mcs in 105.589180s (20.608 KiB/s)
verified 2192012 bytes in 7.037476s (304.177 KiB/s)
9.87user 16.16system 1:53.16elapsed 23%CPU (0avgtext+0avgdata 24768maxresident)k
```
Change-Id: I6696bd4cda7c89ac5ccd21b2ff3aa1663d7d7190
* Clean up formatting.
Change-Id: I7f2d792a2b9432a04209272abb00d8136ee01025
Valgrind and Clang Static Analyzer have no complaints about this change.
Change-Id: I7757615ec52448372bdc57729cdf97c7016d97e8
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4656
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1
Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.
Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* flash/nor: Add support for TI CC26xx/CC13xx flash
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
* flash/nor/nrf5: remove is_erased setting and autoerase before write
Cached flash erase state in sectors[].is_erased is not reliable as running
target can change the flash.
Autoerase was issued before flash write on condition is_erased != 1
Remove autoerase completely as it is a quite non-standard feature.
Change-Id: I19bef459e6afdc4c5fcaa2ccd194cf05be8a42b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4400
Tested-by: jenkins
* src/flash/tms470: remove testing of sectors[].is_erased state
The erase check routine checked sectors only if is_erased != 1
Check sector unconditionally.
While on it fix clang static analyzer warnings.
Change-Id: I9988615fd8530c55a9b0c54b1900f89b550345e9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4401
Tested-by: jenkins
* tcl/target/stm32f7x: configure faster system clock in reset-init
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/psoc5lp: fix compile issue on GCC 8.1.0
Issue already identified by Alex https://sourceforge.net/u/alexbour/
in ticket #191https://sourceforge.net/p/openocd/tickets/191/
src/flash/nor/psoc5lp.c:237:2: error: ‘strncpy’ output
truncated before terminating nul copying 2 bytes from a
string of the same length [-Werror=stringop-truncation]
Fix it by assigning the value to the array elements.
Change-Id: I22468e5700efa64ea48ae8cdec930c48b4a7d8fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4563
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm: Add PLD command to ARM disassembler.
Updates the ARM disassembler to handle PLD (PreLoad Data) commands.
Previously handled by printing a TODO message. There are three forms of
the command: literal, register, and immediate. Simply decode based off
of the A1 encoding for the instructions in the ARM ARM. Also fixes mask
to handle PLDW commands.
Change-Id: I63bf97f16af254e838462c7cfac80f6c4681c556
Signed-off-by: James Marshall <jcmarsh@gwmail.gwu.edu>
Reviewed-on: http://openocd.zylin.com/4348
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* mips_m4k.c: Fix build with --disable-target64
Replace PRIx64 with TARGET_PRIxADDR to avoid build problems
when --disable-target64 is used during configure.
Change-Id: I054a27a491e86c42c9386a0488194320b808ba96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4566
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/arm_adi_v5: sync CSW and TAR cache on apreg write
When using apreg to change AP registers CSW or TAR we get internal
cached value not valid anymore.
Reuse the setup functions for CSW and TAR to write them.
Invalidate the cached value before the call to force the write, thus
keeping original apreg behaviour.
Change-Id: Ib14fafd5e584345de94f2e983de55406c588ac1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4565
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: keep CSW and TAR cache updated
The call to dap_queue_ap_write() can fail and the value in CSW and
TAR becomes unknown.
Invalidate the OpenOCD cache if dap_queue_ap_write() fails.
Change-Id: Id6ec370b4c5ad07e454464780c1a1c8ae34ac870
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4564
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target: Add Renesas R-Car R8A7794 E2 target
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7790 H2 Stout board
Add configuration for the Renesas R-Car R8A7790 H2
based Stout ADAS board.
Change-Id: Ib880b5d2e1fab5c8c0bc0dbcedcdce8055463fe2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4497
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7791 M2W Porter board
Add configuration for the Renesas R-Car R8A7791 M2W
based Porter evaluation board.
Change-Id: Iaadb18f29748f890ebb68519ea9ddbd18e7649af
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4498
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7794 E2 Silk board
Add configuration for the Renesas R-Car R8A7794 E2
based Silk evaluation board.
Change-Id: I504b5630b1a2791ed6967c6c2af8851ceef9723f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
NOTE: This requires SW7[1] in position 1 (default is 0)
Reviewed-on: http://openocd.zylin.com/4532
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Factor out common R-Car Gen2 code
Factor out the code shared by all R-Car Gen2 boards into a single
file to get rid of the duplication.
Change-Id: I70b302c2e71f4e6fdccb2817dd65a5493bb393d8
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4533
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag/drivers/cmsis-dap: fix connect in cmsis_dap_swd_switch_seq()
The proc cmsis_dap_swd_switch_seq() is part of the SWD API for
this interface driver. It is valid only when the interface is
used in SWD mode.
In this proc there is the need to call, in sequence, first
cmsis_dap_cmd_DAP_Disconnect() then cmsis_dap_cmd_DAP_Connect().
The latter call requires the connection mode as parameter, that
inside cmsis_dap_swd_switch_seq() can only be CONNECT_SWD.
The current implementation is not correct and in some cases can
pass mode CONNECT_JTAG. Moreover, JTAG is optional in CMSIS-DAP
and passing mode CONNECT_JTAG triggers an error with SWD-only
interfaces.
Use mode CONNECT_SWD in SWD specific cmsis_dap_swd_switch_seq().
Change-Id: Ib455bf5b69cb2a2d146a6c8875387b00c27a5690
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4571
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: return error if breakpoint address is out of range
If the "Flash Patch and Breakpoint" unit is rev.1 then it can only
accept breakpoint addresses below 0x1FFFFFFF.
Detailed info in "ARM v7-M Architecture Reference Manual", DDI0403E
at chapter "C1.11 Flash Patch and Breakpoint unit".
Print a message and return error if the address of hardware
breakpoint cannot be handled by the breakpoint unit.
Change-Id: I95c92b1f058f0dfc568bf03015f99e439b27c59b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4535
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/stm32: Report errors in wait_status_busy
Flash operation errors that occur during algorithm programming are
reported via the algorithm return value. However, Flash operation
errors that occur during non-algorithm work (erasing, programming
without a work area, programming the last non-multiple-of-32-bytes on
an H7, etc.) generally end with a call to stm32x_wait_status_busy,
which reads the status register and clears the error flags but fails
to actually report that something went wrong should an error flag
(other than WRPERR) be set. Return an error status from
stm32x_wait_status_busy in those cases. Correct a log message
accordingly.
Change-Id: I09369ea5f924fe58833aec1f45e52320ab4aaf43
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4519
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32: Eliminate working area leak
On a specific early-return path, an allocated working area was not
freed. Free it.
Change-Id: I7c8fe51ff475f191624086996be1c77251780b77
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4520
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32h7: Fix incorrect comment
The name of the bit according to the reference manual is inconsistency
error, not increment error.
Change-Id: Ie3b73c0312db586e35519e03fd1a5cb225673d97
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4521
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* target: fix 'bp' command help message
"asid" and "length" are separate arguments of the command.
Put space between them.
Change-Id: I36cfc1e3a01caafef4fc3b26972a0cc192b0b963
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4511
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Add ARM v8 AArch64 semihosting support
This patch implements semihosting support for AArch64. This picks
code from previously submitted AArch64 semihosting support patch
and rebases on top of reworked semihosting code. Tested in AArch64
mode on a Lemaker Hikey Board with NewLib and GDB.
Change-Id: I228a38f1de24f79e49ba99d8514d822a28c2950b
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4537
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* GDB fileIO stdout support
This patch fixes gdb fileio support to allow gdb console to be used as stdout.
Now we can do something like
gdb <inferior file>
(gdb) tar ext :3333
(gdb) load
(gdb) monitor arm semihosting enable
(gdb) monitor arm semihosting_fileio enable
(gdb) continue
Here: Output from inferior using puts, printf etc will be routed to gdb console.
Change-Id: I9cb0dddda1de58038c84f5b035c38229828cd744
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4538
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target: armv8: Avoid semihosting segfault on halt
Avoid a NULL pointer dereference when halting an aarch64 core.
Change-Id: I333d40475ab26e2f0dca5c27302a5fa4d817a12f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4593
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: target: Add NXP LS1012A config
As seen on the FRDM-LS1012A board.
Change-Id: Ifc9074b3f7535167b9ded5f544501ec2879f5db7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4594
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: board: Add NXP Freedom FRDM-LS1012A config
An update for the K20 CMSIS-DAP firmware can be found here:
https://community.nxp.com/thread/387080?commentID=840141#comment-840141
Change-Id: I149d7f8610aa56daf1aeb95f14ee1bf88f7cb647
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4595
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: only trigger once the event gdb-detach at gdb quit
When GDB quits (e.g. with "quit" command) we first execute
gdb_detach() to reply "OK" then, at GDB disconnect (either TCP
or pipe connection type), we execute gdb_connection_closed().
In case GDB is killed or it crashes, OpenOCD only executes the
latter when detects the disconnection.
Both gdb_detach() and gdb_connection_closed() trigger the event
TARGET_EVENT_GDB_DETACH thus getting it triggered twice on clean
GDB quit.
Do not trigger the event TARGET_EVENT_GDB_DETACH in gdb_detach()
and let only gdb_connection_closed() to handle it.
Change-Id: Iacf035c855b8b3e2239c1c0e259c279688b418ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4585
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* gdb_server: set current_target from connection's one
In a multi-target environment we are supposed to have a single
gdb server for each target (or for each group of targets within
a SMP node).
By default, the gdb attached to a server sends its command to
the target (or to the SMP node targets) linked to that server.
This is working fine for the normal gdb commands, but it is
broken for the native OpenOCD commands executed through gdb
"monitor" command. In the latter case, gdb "monitor" commands
will be executed on the current target of OpenOCD configuration
script (that is either the last target created or the target
specified in a "targets" command).
Fixed in gdb_new_connection() by replacing the current target
in the connection's copy of command context.
Change-Id: If7c8f2dce4a3138f0907d3000dd0b15e670cfa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4586
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/image: make i/j unsigned to avoid ubsan runtime error
src/target/image.c:1055:15: runtime error: left shift of 128 by 24 places cannot be represented in type 'int'
Change-Id: I322fd391cf3f242beffc8a274824763c8c5e69a4
Signed-off-by: Cody Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4584
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/stm32f7x: Clear stuck HSE clock with CSS
Change-Id: Ica0025ea465910dd664ab546b66f4f25b271f1f5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4570
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* psoc5lp: fix erase check, add free_driver_priv
psoc5lp_erase_check() was not properly adapted to the new
armv7m_blank_check_memory() in the hot fix 53376dbbed
This change fixes handling of num_sectors in dependecy of ecc_enabled.
Also add comments how ecc_enabled influences num_sectors.
Add pointer to default_flash_free_driver_priv() to all psoc5lp flash
drivers to keep valgrind happy.
Change-Id: Ie1806538becd364fe0efb7a414f0fe6a84b2055b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4569
Tested-by: jenkins
* target: atmel samd10 xplained mini
cortex m0+ on a tiny board, with an mEDBG (CMSIS-DAP) debug interface.
Change-Id: Iaedfab578b4eb4aa2d923bd80f220f59b34e6ef9
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: add SAMD11 Xplained Pro evaluation board
Change-Id: Id996c4de6dc9f25f71424017bf07689fea7bd3af
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4507
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Adds SAMD11D14AU flash support.
Corrects names of SAMD11D14AM and SAMD11D14ASS per datasheet.
Change-Id: I8beb15d5376966a4f8d7de76bfb2cbda2db440dc
Signed-off-by: Christopher Hoover <ch@murgatroid.com>
Reviewed-on: http://openocd.zylin.com/4597
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nds32: Avoid detected JTAG clock
AICE2 doesn't support scan for the maximum clock frequency of
JTAG chain. It will cause USB command timeout.
Change-Id: I41d1e3be387b6ed5a4dd0be663385a5f053fbcf9
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/4292
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl: Distinguish between sectors and blocks in status messages
Use the right word in flash protect command status messages based on
whether the target bank defines num_prot_blocks. Minor message style
tidy-up.
Change-Id: I5f40fb5627422536ce737f242fbf80feafe7a1fc
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4573
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* drivers: cmsis-dap: pull up common connect code
Just a minor deduplication
Change-Id: Idd256883e5f6d4bd4dcc18462dd5468991f507b3
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* drivers: cmsis-dap: Print version info when available
No need to wait until after connecting, might help diagnose part information by
printing earlier.
Change-Id: I51eb0d584be306baa811fbeb1ad6a604773e602c
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3404
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor: add support for TI MSP432 devices
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/at91sam4: fix sam4sa16c flash banks and its gpnvms count
There was already a github fork that had this fixed, but as we try
to use the latest, non-modified version of all software we use,
I would like to have this fix in the next releases of OpenOCD so
that if people uses $packagemanager, they will not have issues flashing
the last part of the flash of sam4sa16c chips.
Additionally, I've added some more logging related to the flash
bank that was used, and the chip ID that was detected.
Change-Id: I7ea5970105906e4560b727e46222ae9a91e41559
Signed-off-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4599
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* flash/nor/stm32lx: Add revision 'V' for STM32L1xx Cat.3 devices
Change-Id: Ic92b0fb5b738af3bec79ae335876aa9e26f5f4cd
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4600
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid null target->semihosting references.
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: Add HWID 0x139 (52832 rev E0)
Change-Id: I71b7471ccfcb8fcc6de30da57ce4165c7fb1f73f
Signed-off-by: James Jacobsson <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4604
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target: Fix segfault for 'mem2array'
Call 'mem2array' without arguments to reproduce the segmentation
fault.
Change-Id: I02bf46cc8bd317abbb721a8c75d7cbfac99eb34e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4534
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/armv7m_trace: Fix typo in enum
Change-Id: I6364ee5011ef2d55c59674e3b97504a285de0cb2
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3904
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/armv7m_trace: Use prefix for enums
Change-Id: I3f199e6053146a1094d96b98ea174b41bb021599
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3905
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/aarch64: Call aarch64_init_debug_access() earlier in aarch64_deassert_reset()
On Renesas R-Car, calling 'reset halt' and 'reset init' always made DAP inaccessible. Calling 'reset' and 'halt' seperatly worked fine.
The only differences seems to be the point in time when aarch64_init_debug_access() is called. This patch aligns the behaviour.
Change-Id: I2296c65e48414a7d9846f12a395e5eca315b49ca
Signed-off-by: Dennis Ostermann <dennis.ostermann@renesas.com>
Reviewed-on: http://openocd.zylin.com/4607
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* server: Improve signal handling under Linux
Commit 5087a955 added custom signal handlers for the openocd
server process.
Before this commit, when openocd is run as a background process
having the same controlling terminal as gdb, Control-C would be
handled by gdb to stop target execution and return to the gdb prompt.
However, after commit 5087a955, the SIGINT caused by pressing
Control-C also terminates openocd, effectively crashing the
debugging session. The only way to avoid this is run openocd in
a different controling terminal or to detach openocd from its
controlling terminal,
thus losing all job control for the openocd process.
This patch improves the server's handling of POSIX signals:
1) Keyboard generated signals (INT and QUIT) are ignored
when server process has is no controlling terminal.
2) SIGHUP and SIGPIPE are handled to ensure that .quit functions
for each interface are called if user's logs out of X
session or there is a network failure.
SIG_INT & SIG_QUIT still stop openocd
when it is running in the foreground.
Change-Id: I03ad645e62408fdaf4edc49a3550b89b287eda10
Signed-off-by: Brent Roman <genosensor@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3963
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* armv7a: read ttbcr and ttb0/1 at every entry in debug state
Commit bfc5c764df avoids reading
ttbcr and ttb0/1 at every virt2phys translation by caching them,
and it updates the cached values in armv7a_arch_state().
But the purpose of any (*arch_state)() method, thus including
armv7a_arch_state(), is to only print out and inform the user
about some architecture specific status.
Moreover, to reduce the verbosity during a GDB session, the
method (*arch_state)() is not executed anymore at debug state
entry (check use of target->verbose_halt_msg in src/openocd.c),
thus the state of translation table gets out-of-sync triggering
Error: Address translation failure
or even using a wrong address in the memory R/W operation.
In addition, the commit above breaks the case of armv7r by
calling armv7a_read_ttbcr() unconditionally.
Fixed by moving in cortex_a_post_debug_entry() the call to
armv7a_read_ttbcr() on armv7a case only.
Remove the call to armv7a_read_ttbcr() in armv7a_identify_cache()
since it is (conditionally) called only in the same procedure
cortex_a_post_debug_entry().
Fixes: bfc5c764df ("armv7a: cache ttbcr and ttb0/1 on debug
state entry")
Change-Id: Ifc20eca190111832e339a01b7f85d28c1547c8ba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4601
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Avoid dereferencing NULL pointer.
If a NULL pointer is passed, don't attempt to increment it. This avoids
passing the now not-NULL pointer on and eventually segfaulting. Also
remove some unnecessary temporary variables.
Change-Id: I268e225121aa283d59179bfae407ebf6959d3a4e
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4550
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Remove FSF mailing address.
Checkpatch complains about this (FSF_MAILING_ADDRESS).
Change-Id: Ib46a7704f9aed4ed16ce7733d43c58254a094149
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* drivers: cmsis_dap_usb: implement cmd JTAG_TMS
Simply add a wrapper around cmsis_dap_cmd_DAP_SWJ_Sequence()
Change-Id: Icf86f84b24e9fec56e2f9e155396aac34b0e06d2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4517
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* arm_adi_v5: put SWJ-DP back to JTAG mode at exit
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add RISC-V support.
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* usb_blaster: Don't unnecessarily go through DR-/IR-Pause
There is no need to pass through DR-/IR-Pause after a scan if we want to
go to DR-/IR-Update. We just have to skip the first step of the path to
the end state because we already did that step when shifting the last
bit.
v2:
- Fix comments as remarked in review of v1
Change-Id: I3c10f02794b2233f63d2150934e2768430873caa
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/4245
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* cortex_a: fix virt2phys when mmu is disabled
When the MMU is not enabled on debug state entry, virt2phys cannot
perform a translation since it is unknown whether a valid MMU
configuration existed before. In this case, return the virtual
address as physical address.
Change-Id: I6f85a7a5dbc200be1a4b5badf10a1a717f1c79c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4480
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* drivers: cmsis-dap: print serial if available
Helpful for sanity checking connections
Change-Id: Ife0d8b4e12d4c03685aac8115c9739a4c1e994fe
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3405
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: make a variable local
The vec_ids variable is not referenced anywhere other than the vector
catch command handler. Make it local to that function.
Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4606
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: fix compile error for uninitialized variable
Commit ad6c71e151 introduced the
variable "mmu_enabled" whose pointer is passed to cortex_a_mmu()
that initialises it.
This initialization is not visible to the compiler that issue
a compile error.
The same situation is common across the same file and the usual
workaround is to initialize it to zero; thus the same fix i
applied here.
Ticket: https://sourceforge.net/p/openocd/tickets/197/
Fixes: commit ad6c71e151 ("cortex_a: fix virt2phys when mmu is disabled")
Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4619
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* mips_m4k: add optional reset handler
In some cases by using SRST we can't halt CPU early enough. And
option PrRst is not available too. In this case the only way is
to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself.
For example by writing to some reset register.
This patch is providing possibility to use user defined reset-assert
handler which will be enabled only in case SRST is disabled. It is
needed to be able switch between two different reset variants on run
time.
Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4404
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target: add config for Qualcomm QCA4531
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable
Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4405
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add config for 8devices LIMA board
More information about this board can be found here:
https://www.8devices.com/products/lima
Change-Id: Id35a35d3e986630d58d37b47828870afd107cc6a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4406
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target|board: move common AR9331 code to atheros_ar9331.cfg
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add DDR2 helper
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add documentation and extra helpers
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add DPTechnics DPT-Board-v1
it is Atheros AR9331 based IoT dev board.
Change-Id: I6fc3cdea1bef49c53045018ff5acfec4d5610ba6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4424
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* fpga/altera-10m50: add all device id
add all currently know Intel (Alter) MAX 10 device ids
Change-Id: I6a88fef222c8e206812499d41be863c3d89fa944
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4598
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target|board: Add Intel (Altera) Arria 10 target and related board
Target information about this SoC can be found here:
https://www.altera.com/products/fpga/arria-series/arria-10/overview.html
Achilles Instant-Development Kit Arria 10 SoC SoM:
https://www.reflexces.com/products-solutions/development-kits/arria-10/achilles-instant-development-kit-arria-10-soc-som
Change-Id: Id78c741be6a8b7d3a70f37d41088e47ee61b437a
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4583
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/riscv: fix compile error with gcc 8.1.1
Fix compile error:
src/target/riscv/riscv-011.c: In function ‘slot_offset’:
src/target/riscv/riscv-011.c:238:4: error: this statement may fall through
[-Werror=implicit-fallthrough=]
switch (slot) {
^~~~~~
src/target/riscv/riscv-011.c:243:3: note: here
case 64:
^~~~
Fixes: a51ab8ddf6 ("Add RISC-V support.")
Change-Id: I7fa86b305bd90cc590fd4359c3698632d44712e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4618
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* server: explicitly call "shutdown" when catch CTRL-C or a signal
Every TCL command can be renamed (or deleted) and then replaced by
a TCL proc that has the same name of the original TCL command.
This can be used either to completely replace an existing command
or to wrap the original command to extend its functionality.
This applies also to the OpenOCD command "shutdown" and can be
useful, for example, to set back some default value to the target
before quitting OpenOCD.
E.g. (TCL code):
rename shutdown original_shutdown
proc shutdown {} {
puts "This is my implementation of shutdown"
# my own stuff before exit OpenOCD
original_shutdown
}
Unfortunately, sending a signal (or pressing CTRL-C) to terminate
OpenOCD doesn't trigger calling the original "shutdown" command
nor its (eventual) replacement.
Detect if the main loop is terminated by an external signal and
in such case execute explicitly the command "shutdown".
Replace with enum the magic numbers assumed by "shutdown_openocd".
Please notice that it's possible to write a custom "shutdown" TCL
proc that does not call the original "shutdown" command. This is
useful, for example, to prevent the user to quit OpenOCD by typing
"shutdown" in the telnet session.
Such case will not prevent OpenOCD to terminate when receiving a
signal; OpenOCD will quit after executing the custom "shutdown"
command.
Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4551
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* zy1000: fix compile error with gcc 8.1.1
The fall-through comment is not taken in consideration by gcc 8.1.1
because it is inside the braces of a C-code block.
Move the comment outside the C block.
Change-Id: I22d87b2dee109fb8bcf2071ac55fdf7171ffcf4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4614
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl.c: fix flash bank bounds check in 'flash fill' command handler
Steps to reproduce ( STM32F103 'Blue Pill', 128KiB of flash ):
> flash fillh 0x0801FFFE 00 1
wrote 2 bytes to 0x0801fffe in 0.019088s (0.102 KiB/s)
> flash fillw 0x0801FFFE 00 1
Error: stm32f1x.cpu -- clearing lockup after double fault
Error: error waiting for target flash write algorithm
Error: error writing to flash at address 0x08000000 at offset 0x0001fffe
Change-Id: I145092ec5e45bc586b3df48bf37c38c9226915c1
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4516
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: add command "dpreg"
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.
Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
$dap_name dpreg reg [value]
Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: add free_driver_priv
Change-Id: I429a9868deb0c4b51f47a4bbad844bdc348e8d21
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/4608
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: add support for NuttX
This patch introduces RTOS support for NuttX. Currently,
only ARM Cortex-M (both FPU and FPU-less) targets are supported.
To use, add the following lines to ~/.gdbinit.
define hookpost-file
eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end
And please make sure the above values are the same as in
src/rtos/nuttx_header.h
Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com>
Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com>
Reviewed-on: http://openocd.zylin.com/4103
Tested-by: jenkins
Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* server/server: Add ability to remove services
Add the ability to remove services while OpenOCD is running.
Change-Id: I4067916fda6d03485463fa40901b40484d94e24e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4054
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: fix incorrect comment
The code sets C_MASKINTS if that bit is not already set (correctly). Fix
the comment to agree.
Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4620
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target/stm32f0x: Allow overriding the Flash bank size
Copy & paste from another stm32 target.
Change-Id: I0f6cbcec974ce70c23c1850526354106caee1172
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4575
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/target: add Allwinner V3s SoC support
Change-Id: I2459d2b137050985b7301047f9651951d72d9e9e
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4427
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/arm_adi_v5: allow commands apsel and apcsw during init phase
The current implementation of apsel cannot be executed during the
initialization phase because it queries the DAP AP to retrieve and
print the content of IDR register, and the query is only possible
later on during the exec phase.
But IDR information is already printed by the dedicated command
apid, making redundant printing it by apsel too.
Being unable to run apsel during initialization, makes also apcsw
command (that depends on apsel) not usable in such phase.
Modify the command apsel to only set the current AP, without making
any transfer to the (possibly not initialized yet) DAP. When run
without parameters, just print the current AP number.
Change mode to COMMAND_ANY to apsel and to apcsw.
Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4624
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: allow command dacrfixup during init phase
There is no reason to restrict the command "cortex_a dacrfixup"
to the EXEC phase only.
Change the command mode to ANY so the command can be used in
the initialization phase too.
Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4623
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/armv7a_cache: add gdb keep-alive and fix a missing dpm finish
Depending on range size, the loop on cache operations can take quite
some time, causing gdb to timeout.
Add keep-alive to prevent gdb to timeout.
Add also a missing dpm->finish() to balance dpm->prepare().
Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4627
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add detail to `wrong register size` error.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Id31499c94b539969970251145e42c89c943fd87c
Reviewed-on: http://openocd.zylin.com/4577
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* doc: fix typo in cortex_m maskisr command
Change-Id: I37795c320ff7cbf6f2c7434e03b26dbaf6fc6db4
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4621
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: restore C_MASKINTS after reset
The cortex_m maskisr user-facing setting is not changed across a target
reset. However, the in-core C_MASKINTS bit was always cleared as part of
reset processing, meaning that a cortex_m maskisr on setting would not
be respected after a reset. Set C_MASKINTS based on the user-facing
setting value rather than always clearing it after reset.
Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4605
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: update all uses of interface/stlink-v2-1 to interface/stlink
Change-Id: I5e27e84d022f73101376e8b4a1bdc65f58fd348a
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4456
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/riscv/riscv-011: fix compile warning about uninitialized variable
In MSYS2 MinGW 64-bit
git clone git://git.code.sf.net/p/openocd/code openocd
$ gcc --version
gcc.exe (Rev1, Built by MSYS2 project) 8.2.0
./bootstrap
./configure --prefix=
$ cat config.status | grep CFLAGS
CFLAGS='-g -O2'
make bindir = "bin-x64"
depbase=`echo src/target/riscv/riscv-011.lo | sed 's|[^/]*$|.deps/&|;s|\.lo$||'`;\
/bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF $depbase.Tpo -c -o src/target/riscv/riscv-011.lo src/target/riscv/riscv-011.c &&\
mv -f $depbase.Tpo $depbase.Plo
libtool: compile: gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF src/target/riscv/.deps/riscv-011.Tpo -c src/target/riscv/riscv-011.c -o src/target/riscv/riscv-011.o
src/target/riscv/riscv-011.c: In function 'poll_target':
src/target/riscv/riscv-011.c:1799:6: error: 'reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
reg_cache_set(target, reg, ((data & 0xffffffff) << 32) | value);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/target/riscv/riscv-011.c:1686:17: note: 'reg' was declared here
unsigned int reg;
^~~
cc1.exe: all warnings being treated as errors
make[2]: *** [Makefile:3250: src/target/riscv/riscv-011.lo] Error 1
Change-Id: I6996dcb866fbace26817636f4bedba09510a087f
Signed-off-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
Reviewed-on: http://openocd.zylin.com/4635
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* max32xxx: Support for MAX32XXX devices.
Adding flash programming support for Maxim Integrated MAX32XXX
devices.
Change-Id: I5b0f57a885f9d813240e4bc2d9f765b743e1cfc3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/3543
Tested-by: jenkins
Reviewed-by: Ismail H. KOSE <ihkose@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* flash/at91sam4: run probe just once
Reread registers in sam4_GetInfo()
Change-Id: I3b023b3e642a9c052b5c41673d196317f7e7f2e3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4609
Tested-by: jenkins
Reviewed-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
* flash/at91sam4: emit flash bank info
Change related LOG_INFO to LOG_DEBUG
Change-Id: I0c09b1ec83da631b26980dc8632b9031fe2921a3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4610
Tested-by: jenkins
Reviewed-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
* flash/at91sam4: set wait states only once per write
Read-modify-write setting of FMR register requires an USB turnaround.
Setting FMR before each page write is not necessary and decreases the
write speed.
Change-Id: I67844c898aaf117f155c762c979840b603c767ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4611
Tested-by: jenkins
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
* flash/at91sam4: fix clang static analyzer warning
Change-Id: I5e5319d855c868adfa012f68086f7f809ec5a069
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4639
Tested-by: jenkins
* rtos/linux.c: fix clang static analyzer warning
Remove sizeof(int64_t) from string size computation.
Change-Id: I029b394df5d62a2594a723c4c0e13608b3423b9b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4640
Tested-by: jenkins
* target: armv8: Ensure target is halted for virt2phys
Othewise the error reported as
Timeout waiting for dpm prepare
Change-Id: Ieed2fdcd94ae4e877a749df3eec07a01dbf80b10
Closes: https://sourceforge.net/p/openocd/tickets/201/
Found-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Guido Günther <guido.gunther@puri.sm>
Reviewed-on: http://openocd.zylin.com/4647
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* adi_v5: enforce check on AP number value
The AP number value is restricted in 8 bits unsigned by ADI-v5
specification. Nevertheless, an "invalid" value is used by
target cortex-m to force an automatic detection of the AP.
Replace magic numbers by using new macros for AP max number and
for the value of AP invalid.
Check the value passed through -ap-num flag during configuration.
Change-Id: Ic19a367db0ab11c0ebd070750eca0647d25279a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4668
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: add per target option "-gdb-port"
The argument passed to global config command "gdb_port" is usually,
but not always, a TCP port number. In case of multiple targets, this
numeric value is used as the first port of a set of consecutive TCP
ports assigned one per target.
If the argument is not a numeric value (e.g. "pipe", "disabled", ...)
then incrementing it for the next target has no sense.
Add the option "-gdb-port number" to the commands "target create" and
"$target_name configure" to override, for the specific target, the
general global configuration.
This permits to use a per target "-gdb-port disabled", when no gdb
port is required for that specific target.
It also makes possible to choose a custom TCP port number for each
target, overriding the usual sequence of consecutive port numbers.
Change-Id: I3b9a1910b28ab4bc757e839d0e5d08ffc29f7ab4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4530
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* libusb: return oocd error values
keep same return style where possible
Change-Id: I2f9b85dbc307a483609f76a84de77e3c74d346c7
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4588
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* rtos-helpers: fix minor typo in uC/OS-III helper
This patch corrects a spelling error in uCOS-III-openocd.c.
Change-Id: I6d1923ff1f5e6361358c45cec3dd6c08ca9ccef0
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4659
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/stm32f2x: add stm32f7 revision Z identification
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: Ia0169514d494bae2a98d92ebc97c8eccc10bc6c4
Reviewed-on: http://openocd.zylin.com/4657
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/mem_ap: generic mem-ap target
This pseudo target allows attaching to any access point on the DAP at the
MEM-AP level and read and write addresses on the connected bus. For
example, one can create a mem_ap target on the APB-AP and read and write
registers of debug components directly. This allows many diagnostic
and other features be programmed entirely using TCL, without necessity
of adding drivers to OpenOCD.
Change-Id: I53229ffd68fb0f96fb68be15b0f3a76cc8843c8e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4002
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Leonard Crestez <cdleonard@gmail.com>
* interface: adapter configuration for FTDI C232HM
This patch adds support for the C232HM-DDSL-0 and C232HM-EDSL-0
FT232H-based cables from FTDI. For more information, see:
http://www.ftdichip.com/Products/Cables/USBMPSSE.htm
Change-Id: Ic97423eb1e2f6b5ebae04943cd5cce86f38771d5
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4081
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* ftdi: extend ftdi_location format
To existing <bus>:<port>,<port> format add <bus>-<port>.<port> support.
The last format is used by kernel and other drivers.
Change-Id: I6528970d3af4f6a8bf7b27a0f7a763b5957fdf2b
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4631
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: poll all targets in SMP node after halt
The periodic poll scans all the targets in the same order they
have been declared in the configuration file.
When one target in a SMP node halts, the transition is detected
in the following poll and this triggers a halt request to all the
other cores of the SMP node.
The targets that will be polled afterwards will be identified as
"halted", but the targets already scanned will remain as
"running" until the next periodic poll.
This creates a race condition with GDB; GDB sets the breakpoints
when runs the target and removes them as soon as the target is
halted. When it receives the halt event, it starts removing the
breakpoints and fails on the targets that are still reported as
"running".
Fixed by polling all the targets in the SMP node before informing
GDB about the halt event.
This implementation is almost copy/paste from the one in aarch64.
Change-Id: Id2bd99f1e56b014e48e9e34ccb891b4219c518f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4622
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Emcraft imx8 SOM BSB support
Tested with Olimex ARM-USB-TINY-H adapter
Simple commands work fine but there are currently issues when attaching
remote gdb or running virt2phys:
https://sourceforge.net/p/openocd/tickets/201/
Change-Id: I86ccf1d93c5d23870bb522f92b3e2af190d529e8
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-on: http://openocd.zylin.com/4646
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* arm_adi_v5: remove useless cast to int
The field ap_num in struct adiv5_private_config is already of type int.
Casting it to type int has no sense.
Change-Id: Ida642e808c02591bb58609425eccd096d404e2c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4666
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nrf5: time-based timeout waiting for flash controller
Change-Id: Id214df154dc359ca130c8d8fe1554d106621b9cd
Signed-off-by: Kai Geissdoerfer <kai.geissdoerfer@tu-dresden.de>
Reviewed-on: http://openocd.zylin.com/4648
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nrf5: support for nRF52840 Q1AAC0
Change-Id: Id3280dadece84e1d68544936e44d506c7930a55d
Signed-off-by: Kai Geissdoerfer <kai.geissdoerfer@tu-dresden.de>
Reviewed-on: http://openocd.zylin.com/4649
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* doc: fix use of deprecated config file in the example
Commit 31c58c139d ("jtag: drivers: stlink: handle all versions with
single config") deprecates the use of "interface/stlink-v2-1.cfg" in
favor of a unique config file "interface/stlink.cfg".
Update the example in the documentation.
Change-Id: I1aed7c70e15f4edb4f81a3ee8e3bce575fde873b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4667
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Added support for STM32L4X option bytes writing.
Enables the programming of Write protection lock bits.
- Updated/re-factored with option_read, option_write and option_load commands.
Change-Id: I86358c7eb1285c3c0baac1564e46da8ced5fd025
Signed-off-by: Thomas Søhus <tls@ceepro.dk>
Reviewed-on: http://openocd.zylin.com/4654
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Clarify what exactly the RISC-V code supports.
Change-Id: I8da657426cc52c738ab41bfb0164cbc6721c0aef
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4655
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: fix typo
The subunit of the debug unit is called the Flash Patch and Breakpoint
unit, abbreviated (by ARM no less) as FPB, not FBP.
Change-Id: Ia2f08470da705f0f1518feeca878f0f500507308
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4675
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* contrib/60-openocd.rules: provide hint to reload udev rules
No need to reboot the Linux box when new rules are added to udev.
Suggest the command in the script header.
Change-Id: Ie95383bfd73914a3d2e2c05d77fa3eb32e68b7e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4665
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* target/stm32: make APCSW cacheable
Change-Id: I7c5c9720ded329848647f17db95f845e46c01c19
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4674
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/atsamv: make APCSW cacheable
Change-Id: Ic00d3192642c682f370a6f7f8b70ae29744eb746
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4678
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* gdb_server: avoid gdb server for virtual targets
Virtual targets, like mem_ap, do not or cannot implement the required
functionality to accept a GDB connection. In the case of mem_ap, the
method get_gdb_reg_list() is missing and a following connection from
gdb causes OpenOCD to segfault.
OpenOCD opens a GDB port for each target; it's always possible to
connect, by mistake, GDB to one virtual target.
Add a method to check if the target supports GDB connections (for the
moment just checking if get_gdb_reg_list is implemented).
Skip opening a gdb server for every targets that don't support GDB
connections.
Change-Id: Ia439a43efe1a9adbb1771cd9d252db8ffa32eb9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4676
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/target: Add Renesas R-Car Gen3 targets
Add configuration for the Renesas R-Car Generation 3 targets.
These are SoCs with Cortex A57s, A53s, and R7s. All cores
are supported.
Change-Id: I795233210e4f647a1a2a0adea7c058ae98b5db70
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4669
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car Salvator-X(S) boards.
Add configuration for the Renesas R-Car Salvator-X
and Renesas R-Car Salvator-XS boards.
Change-Id: I898008f56adb31908d30760f18217583fabf1c51
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4670
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* flash/nrf5: support for nRF52810
Change-Id: I01c430bfa593d20ea7a51c90d67052e374d239b3
Signed-off-by: Anders Westrup <anders@westrup.se>
Reviewed-on: http://openocd.zylin.com/4680
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Slowcoder <slowcoder@gmail.com>
* drivers: cmsis-dap: fix connection in JTAG mode
Commit 5aceec2412 ("drivers:
cmsis-dap: pull up common connect code") breaks the driver and it
cannot connect anymore in JTAG mode.
The issue is caused in cmsis_dap_init() by anticipating the call to
cmsis_dap_usb_open(), which then sets cmsis_dap_handle and makes the
following test to always fail.
Actually the original code was quite tricky:
if (swd_mode)
do something that also sets cmsis_dap_handle;
if (cmsis_dap_handle == NULL)
do something for !swd_mode;
Convert the sequence of tricky "if"s in a single "if-then-else" to
handle clearly the cases swd_mode and !swd_mode.
Change-Id: I359a23bf26a3edc2461f4352daa0be83e78868f7
Fixes: 5aceec2412 ("drivers: cmsis-dap: pull up common connect code")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4697
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* register: support non-existent registers
This patch fixes a number of bugs caused by incomplete support for
non-existent registers. This is needed for targets that provide optional
registers or non-linear register numbers.
Change-Id: I216196e0051f28887a2c3da410959382369eed80
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* rtos: support gdb_get_register_packet
This patch adds support for p packet responses by targets configured
with RTOS support. This change required moving to a rtos_reg struct,
which is similar to struct reg used by targets, which resulted in
needing to update each stacking with register numbers. This patch also
allows targets with non-linear register numbers to function with RTOSes
as well.
Change-Id: I5b189d74110d6b6f2fa851a67ab0762ae6b1832f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4121
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: add support for architecture element
This change adds optional support for a target to report architecture
information in the target description to GDB. This is needed by some GDB
implementations to properly support remote target with custom behavior.
More information on the architecture element can be found here:
https://sourceware.org/gdb/onlinedocs/gdb/Target-Description-Format.html#Target-Description-Format
Change-Id: I57b19cae5ac3496256e4e5cc52cf6526ca5c322d
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4078
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag: make cmd_queue_scan_field_clone public
This patch makes the cmd_queue_scan_field_clone function public. This
permits targets to insert fields without affecting the submitted
scan_field list. This will be used in an upcoming target implementation
that needs to insert additional padding bits.
Change-Id: I8fbd3b9b4e413432471f4f1444048932c8fa189e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4082
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* esirisc: support eSi-RISC targets
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* rtos: check symbol list when updating uCOS-III
This patch corrects a crash in uCOS-III on a new GDB connection when
RTOS autodetection is not used. The crash was caused by not checking if
the symbol list had been loaded prior to updating threads.
Change-Id: I64c5133e02fe22fc8d14584cc40d87b49c935b0b
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4719
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* ftdi: demote unhelpful debug messages
Some protocols make use of empty scan fields for optional padding, which
causes the log to fill with unhelpful messages that a field is empty.
The remaining LOG_DEBUG messages in ftdi_execute_scan have been demoted
to DEBUG_JTAG_IO such that these messages are only seen when debugging
JTAG.
Change-Id: I61fd4551411ce851da34e67d003bca5d7a71cd92
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4112
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* tcl: Add support for the Numato Lab Mimas A7 board
The Mimas A7 FPGA board has FTDI FT2232 whose channel B is connected to
Artix-7 FPGA's JTAG interface. Hence, OpenOCD can easily interface with
it via the its ftdi driver interface. Tested to be working great up to
30 MHz.
Change-Id: Ieda015fbc6135bf95ad5a069cbf38650da45911e
Signed-off-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-on: http://openocd.zylin.com/4720
Tested-by: jenkins
Reviewed-by: Tim "mithro" Ansell <me@mith.ro>
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/arm_adi_v5: fix sync CSW cache on apreg write
Commit 0057c71ab6 updates the OpenOCD
cached values of CSW and TAR registers if these registers are modified
by an apreg command.
The condition to force the update of CSW cache is incorrect and it will
erase the default CSW value.
Moreover, calling mem_ap_setup_csw() does not honor the value requested
in the apreg command because such value is incorrectly bitwise or-ed
with csw_default.
Fix it by updating csw_value, instead of erasing csw_default, and writing
directly in CSW register the new value from the command line.
Change-Id: I40273cb64d22ccfb9b6d3499bd39b586eb60de38
Fixes: 0057c71ab6 ("target/arm_adi_v5: sync CSW and TAR cache on apreg write")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4679
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: Add Arty-S7 Spartan 7 FPGA Development Board
Change-Id: I8bfe780cb67a1777d5112a68e8a9781bfe4f2038
Signed-off-by: William D. Jones <wjones@wdj-consulting.com>
Reviewed-on: http://openocd.zylin.com/4525
Reviewed-by: Robert Jordens <jordens@gmail.com>
Tested-by: jenkins
Reviewed-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* xilinx-xc7: Add additional IDCODEs.
Add/detect missing IDCODEs for the Spartan 7 family and Artix 25T
and Artix 12T.
Change-Id: Ib6c83c5592e90df1eb8e715e79b279da9a95f9c6
Signed-off-by: William D. Jones <wjones@wdj-consulting.com>
Reviewed-on: http://openocd.zylin.com/4428
Reviewed-by: Robert Jördens
Tested-by: jenkins
Reviewed-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: fix temporary breakpoint during step
Commit c8926d1457 introduces the
context and hybrid breakpoint types beside existing SW and HW
types. The new field "asid" is non-zero only for these new types.
The commit above did not properly initialize "asid" to 0 for a
temporarily HW breakpoint used during single step. This causes
cortex_a_unset_breakpoint() to identify this breakpoint as of
type "hybrid".
Identified through valgrind error:
Conditional jump or move depends on uninitialised value(s)
Actually valgrind triggers a total of 10 messages about use of
uninitialized variables, but they are all caused by the first
conditional jump bases on "asid != 0".
Fixed by initializing "asid" to 0 in cortex_a_step().
Fixes: c8926d1457 ("cortex_a hybrid & context breakpoints")
Change-Id: Ib674d8457d1e02e10332fd9d73554d13719ef93d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4613
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* zynq_7000: Add zynqpl_program command
This allows for programming the PL part of the Xilinx Zynq 7000
Change-Id: I89e86c0f381951091f6948c46802d17d7f1f3500
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4177
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/target.c: adding keep_alive() to while loop.
Adding the call to keep_alive() to suppress warnings when
running the async flash algorithm. Issue observed when
loading large pieces of code on slower debuggers.
Change-Id: I7660fa05f68ebd7be07b2ca0a55b0f3b6ae718f3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/4686
Tested-by: jenkins
Reviewed-by: Jesse Marroquin
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* drivers/cmsis-dap: speed up sending multiple HID requests
The performance of CMSIS-DAP in long data transfers was improved substantially in
ef02b69b14. But it not as good as some
other USB/MCU based adapters. Using HID and therefore interrupt endpoint
is slower than USB bulk transfer.
CMSIS-DAP adapter implements multiple HID buffer handling and OpenOCD already
reads number of buffers from info command.
This change adds capability to sumbit more than one HID requests before
driver waits for a HID response. This scenario is used for long transfers only.
Results show about double speed on USB FS and ~140% speed on USB HS:
| w/o this change | with multi HIDrq
-----------------------------------------+-----------------+-----------------
Open source CMSIS-DAP, USB FS, adapter_khz 1000
dump_image ram32k.bin 0x1fffe000 0x8000 | 23.225 KiB/s | 45.901 KiB/s
load_image ram32k.bin 0x1fffe000 | 23.324 KiB/s | 46.552 KiB/s
Cypress' Kitprog in CMSIS-DAP mode, USB FS, adapter_khz 1000 (over firmware limit)
dump_image ram64k.bin 0x20000000 0x10000 | 15.537 KiB/s | 42.558 KiB/s
load_image ram64k.bin 0x20000000 | 15.605 KiB/s | 43.291 KiB/s
Atmel's EDBG, USB HS, adapter_khz 10000 (#3945 applied)
dump_image ram384k.bin 0x20400000 0x6000 | 248.402 KiB/s | 345.250 KiB/s
load_image ram384k.bin 0x20400000 | 256.039 KiB/s | 365.945 KiB/s
Change-Id: I9edbe018086176d357c6aaba5d6b657a5e5e1c64
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4080
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl: target: omit apcsw for hla
When using stlink for CM7 targets we have to rely on its firmware
to do the right thing as direct DAP access is not possible.
Change-Id: Ieee69f4eeea5c911f89f060f31ce86ed043bdfd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4732
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/at91samd: add SAMR21E19A DID
While on it correct RAM amount of SAMR21x16A devices
Change-Id: Ie9ab9de1551bdceff17af7597a9a2ee41f5aebe0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4734
Reviewed-by: Eduardo Montoya
Tested-by: jenkins
* arm_adi_v5: do not deactivate power domains while trying to clear sticky error
At OpenOCD start-up the operation of clearing the sticky error in
CTRL/STAT register ignores the current value of the power domains
bits CDBGPWRUPREQ and CSYSPWRUPREQ in the same register and
incorrectly set them to zero.
This abrupt disable does not follow the requirement in IHI0031 to
wait for the acknowledgment of power disabled before continuing.
The power domains are then re-enabled immediately after; it is
possible that such short disable period has passed undetected or
has been tested only on devices that do not implement the power
domains.
Anyway, this sequence is incorrect and can generate unexpected
and hard-to-debug issues while OpenOCD attaches to a running
target that implements power domains.
Anticipate the initialization of dap->dp_ctrl_stat and use it
while clearing the sticky bit. This has the additional effect of
avoiding a power disable in the error recovery part of the
function dap_dp_read_atomic().
Keep the same sequence of read/write in dap_dp_init() to avoid
breaking the initialization of some problematic target.
Add comments to document these choices.
Change-Id: I8d6da788f2dd11909792b5d6b69bc90fbe4df25d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4677
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* flash/nor/stm32f1x: Use of protection blocks, improved option bytes handling
Handle write protection status in blocks instead of sectors, removing
unnecessary complexity in the process. Now closer to stm32f2x.
Support sequential modification of option bytes by read/modify/write
directly to option bytes area instead of always starting with the
currently loaded bytes from FLASH_OBR/WRPR registers.
Added new command 'options_load' to force re-load of option bytes w/o
having to power cycle target.
Change-Id: I5c76191e29c17a1e11482df06379d10ca8d6d04d
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4576
Tested-by: jenkins
Reviewed-by: Jan Vojtěch <honza.vojtech@gmail.com>
* target/cortex_a: remove unused code controlled by "fast_reg_read"
The variable fast_reg_read is always zero, causing some code to
never be executed.
Such code try to read the target registers by dumping them in
memory and then reading back the memory through the debugger. But
it is broken due to lack of cache and MMU management.
This code also uses the broken memory_ap access that is going to
be removed soon.
Remove all the code that depends on fast_reg_read not zero.
Add a missing check on arm_dpm_read_current_registers() return.
Keep the unused function cortex_a_dap_write_coreregister_u32()
to balance the used "read" version.
Change-Id: If2ff28a8c49eb0a87dc85207f5431978efd158db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4746
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: remove buggy memory AP accesses
The armv7m debug port provides a direct access to the CPU memory
bus, allowing the debugger to bypass the CPU for every memory
operation.
The armv7a debug port doesn't offer the same feature, mainly
because CPU caches and MMU makes the direct memory access more
tricky. Nevertheless most SoC with armv7a provide direct memory
access through an AHB bus available on another DAP access port,
different from the debug port.
The original port of cortex_a in OpenOCD was inspired from the
working cortex_m code, and provided optional memory access
through the AHB, if present.
The code for AHB access is problematic and partially buggy due
to incomplete management of cache coherency and missing check of
page boundary during virtual address operations.
With the commit 5d458cf727
("target/mem_ap: generic mem-ap target") we have a clean support
for memory access through system buses connected to DAP AP, which
obsoletes the buggy memory AP hack in cortex_a.
Remove any code that uses the memory AP accesses in cortex_a.
Change-Id: I7cd1f94885e5817448058953e043d8da90dea3cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4748
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/arm_dpm: uniform names of exported functions
The name of the function dpm_modeswitch() does not follow the
common style of the other function names in the same file.
Rename it as arm_dpm_modeswitch().
Change-Id: Idebf3c7bbddcd9b3c7b44f8d0dea1e5f7549b0eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4756
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: remove duplicate code to read target registers
The functions cortex_a_dap_{read,write}_coreregister_u32() are
duplicate of the functions dpm_{read,write}_reg().
Remove both duplicated functions in cortex_a.c while export only
dpm_read_reg(), since dpm_write_reg() is currently not used.
Rename dpm_read_reg() as arm_dpm_read_reg() to keep uniform the
naming style.
Change-Id: I501bc99dc402039e630c47917a086a0bb382782c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4747
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
* armv7a: ARMv7-A MMU tools
factor out mmu-related code from armv7a.c, add a 'dump' command for
page tables.
Change-Id: Ic1ac3c645d7fd097e9d625c7c8302e7065875dd4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag/bitq: array boundary overflow
The for loop inside bitq_path_move function is not correct, this will
overflow the cmd->path array and produces an unpredictable result.
Change-Id: I81e3bc9ee6d1dd948acd2fe4c667103ac22bb26f
Signed-off-by: xuguangxiao <szgxxu@qq.com>
Reviewed-on: http://openocd.zylin.com/4733
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/stm32h7x: Fix documentation of reset_config
The stm32h7x.cfg does not specify connect_assert_srst or
connect_deassert_srst in its reset_config. The comment claims that it
will therefore connect in reset. However, per the manual, the default
configuration is actually connect_deassert_srst, not
connect_assert_srst. In actual fact, connect_assert_srst does not work
on the STM32H7 because, while SRST is asserted, everything on the AXI
bus is inaccessible. The CPU core is accessible, but since the
examine-end event handler also pokes at the DBGMCU peripheral, that will
fail in connect_assert_srst mode. So using connect_deassert_srst is
appropriate, so fix the comment accordingly.
Change-Id: If3e32e871fb19cc61183bdf911b7c5efd80b62e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4741
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* docs: fix typo in manual
Change-Id: I28717105eb2a907b0cb4b03f4b5ff1f47194413b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4751
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* README: fix stlink instructions
Since 31c58c139d there is a unified config
for all stlink versions.
Change-Id: Id736063496ecd96e2024ed69dcb67a22c44b80bb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4672
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Permit null target on TCL connection
In previous versions of OpenOCD, it was possible to connect to the TCL
RPC interface without a current target. In `tcl_new_connection`, the
curent target would be queried by number, and the possibility of a null
current target was handled properly.
In commit bb9d9c6026, the
`get_target_by_num` call was replaced by a `get_current_target` call,
without noticing that `get_current_target` aborts if there is no current
target, whereas `tcl_new_connection` is perfectly able to handle that
situation.
Provide a `get_current_target_or_null` function for use by consumers who
are OK with a null current target, and use it in `tcl_new_connection`.
Change-Id: I06f7e1e149f1169e23c73ba328c7ad9f9425cc2a
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4730
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
* riscv_get_thread_reg_list matches new prototype.
None of the existing test cases cause this function to be called. I
suspect it never gets called, since it is weird to have a function that
only returns the GPRs as a full list of registers.
Change-Id: Ib54f182c1b2fc4dd711c877cb5c9b3e0af77461d
* Fix conflict resolutions.
Change-Id: I5228c308a08ee54530f8c1cadac2afe1c974d41e
* WIP upstream review feedback.
See http://openocd.zylin.com/#/c/4656/
The main change is to get rid of macros that contain a return statement.
Change-Id: Iff79a8aa7c40ee04a8d1f07d973f9b29d4899d5c
* Remove unaligned head/tail code.
From inspection it's not clear to me that this is necessary at all. I've
been unable to make a test case that results in anything besides a
4-byte aligned flash to happen. Sections that aren't multiples of 4 are
common, and appear to work fine.
Change-Id: Idb6109ca015ae06b9d8f16bd883f9c8f5c51087d
* Move fespi native code into contrib/loaders
As suggested by http://openocd.zylin.com/#/c/4656/
Change-Id: I275012aa8a1ef6a0e8a2ec8ebe8643d87de24407
* Reenable hw mode if errors happen without it.
Change-Id: I1220033c13d02e8a441992bd6daa0ec3b5acbfca
* Default flash to not protected.
Requested by upstream review.
Change-Id: I61753bd9909d7f21ef6624037a865072c18bd1d8
No need to reboot the Linux box when new rules are added to udev.
Suggest the command in the script header.
Change-Id: Ie95383bfd73914a3d2e2c05d77fa3eb32e68b7e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4665
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch corrects a spelling error in uCOS-III-openocd.c.
Change-Id: I6d1923ff1f5e6361358c45cec3dd6c08ca9ccef0
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4659
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Adding flash programming support for Maxim Integrated MAX32XXX
devices.
Change-Id: I5b0f57a885f9d813240e4bc2d9f765b743e1cfc3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/3543
Tested-by: jenkins
Reviewed-by: Ismail H. KOSE <ihkose@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* flash/nor: Add support for TI CC26xx/CC13xx flash
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
* flash/nor/nrf5: remove is_erased setting and autoerase before write
Cached flash erase state in sectors[].is_erased is not reliable as running
target can change the flash.
Autoerase was issued before flash write on condition is_erased != 1
Remove autoerase completely as it is a quite non-standard feature.
Change-Id: I19bef459e6afdc4c5fcaa2ccd194cf05be8a42b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4400
Tested-by: jenkins
* src/flash/tms470: remove testing of sectors[].is_erased state
The erase check routine checked sectors only if is_erased != 1
Check sector unconditionally.
While on it fix clang static analyzer warnings.
Change-Id: I9988615fd8530c55a9b0c54b1900f89b550345e9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4401
Tested-by: jenkins
* tcl/target/stm32f7x: configure faster system clock in reset-init
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/psoc5lp: fix compile issue on GCC 8.1.0
Issue already identified by Alex https://sourceforge.net/u/alexbour/
in ticket #191https://sourceforge.net/p/openocd/tickets/191/
src/flash/nor/psoc5lp.c:237:2: error: ‘strncpy’ output
truncated before terminating nul copying 2 bytes from a
string of the same length [-Werror=stringop-truncation]
Fix it by assigning the value to the array elements.
Change-Id: I22468e5700efa64ea48ae8cdec930c48b4a7d8fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4563
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm: Add PLD command to ARM disassembler.
Updates the ARM disassembler to handle PLD (PreLoad Data) commands.
Previously handled by printing a TODO message. There are three forms of
the command: literal, register, and immediate. Simply decode based off
of the A1 encoding for the instructions in the ARM ARM. Also fixes mask
to handle PLDW commands.
Change-Id: I63bf97f16af254e838462c7cfac80f6c4681c556
Signed-off-by: James Marshall <jcmarsh@gwmail.gwu.edu>
Reviewed-on: http://openocd.zylin.com/4348
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* mips_m4k.c: Fix build with --disable-target64
Replace PRIx64 with TARGET_PRIxADDR to avoid build problems
when --disable-target64 is used during configure.
Change-Id: I054a27a491e86c42c9386a0488194320b808ba96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4566
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/arm_adi_v5: sync CSW and TAR cache on apreg write
When using apreg to change AP registers CSW or TAR we get internal
cached value not valid anymore.
Reuse the setup functions for CSW and TAR to write them.
Invalidate the cached value before the call to force the write, thus
keeping original apreg behaviour.
Change-Id: Ib14fafd5e584345de94f2e983de55406c588ac1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4565
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: keep CSW and TAR cache updated
The call to dap_queue_ap_write() can fail and the value in CSW and
TAR becomes unknown.
Invalidate the OpenOCD cache if dap_queue_ap_write() fails.
Change-Id: Id6ec370b4c5ad07e454464780c1a1c8ae34ac870
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4564
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target: Add Renesas R-Car R8A7794 E2 target
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7790 H2 Stout board
Add configuration for the Renesas R-Car R8A7790 H2
based Stout ADAS board.
Change-Id: Ib880b5d2e1fab5c8c0bc0dbcedcdce8055463fe2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4497
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7791 M2W Porter board
Add configuration for the Renesas R-Car R8A7791 M2W
based Porter evaluation board.
Change-Id: Iaadb18f29748f890ebb68519ea9ddbd18e7649af
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4498
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7794 E2 Silk board
Add configuration for the Renesas R-Car R8A7794 E2
based Silk evaluation board.
Change-Id: I504b5630b1a2791ed6967c6c2af8851ceef9723f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
NOTE: This requires SW7[1] in position 1 (default is 0)
Reviewed-on: http://openocd.zylin.com/4532
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Factor out common R-Car Gen2 code
Factor out the code shared by all R-Car Gen2 boards into a single
file to get rid of the duplication.
Change-Id: I70b302c2e71f4e6fdccb2817dd65a5493bb393d8
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4533
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag/drivers/cmsis-dap: fix connect in cmsis_dap_swd_switch_seq()
The proc cmsis_dap_swd_switch_seq() is part of the SWD API for
this interface driver. It is valid only when the interface is
used in SWD mode.
In this proc there is the need to call, in sequence, first
cmsis_dap_cmd_DAP_Disconnect() then cmsis_dap_cmd_DAP_Connect().
The latter call requires the connection mode as parameter, that
inside cmsis_dap_swd_switch_seq() can only be CONNECT_SWD.
The current implementation is not correct and in some cases can
pass mode CONNECT_JTAG. Moreover, JTAG is optional in CMSIS-DAP
and passing mode CONNECT_JTAG triggers an error with SWD-only
interfaces.
Use mode CONNECT_SWD in SWD specific cmsis_dap_swd_switch_seq().
Change-Id: Ib455bf5b69cb2a2d146a6c8875387b00c27a5690
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4571
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: return error if breakpoint address is out of range
If the "Flash Patch and Breakpoint" unit is rev.1 then it can only
accept breakpoint addresses below 0x1FFFFFFF.
Detailed info in "ARM v7-M Architecture Reference Manual", DDI0403E
at chapter "C1.11 Flash Patch and Breakpoint unit".
Print a message and return error if the address of hardware
breakpoint cannot be handled by the breakpoint unit.
Change-Id: I95c92b1f058f0dfc568bf03015f99e439b27c59b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4535
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/stm32: Report errors in wait_status_busy
Flash operation errors that occur during algorithm programming are
reported via the algorithm return value. However, Flash operation
errors that occur during non-algorithm work (erasing, programming
without a work area, programming the last non-multiple-of-32-bytes on
an H7, etc.) generally end with a call to stm32x_wait_status_busy,
which reads the status register and clears the error flags but fails
to actually report that something went wrong should an error flag
(other than WRPERR) be set. Return an error status from
stm32x_wait_status_busy in those cases. Correct a log message
accordingly.
Change-Id: I09369ea5f924fe58833aec1f45e52320ab4aaf43
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4519
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32: Eliminate working area leak
On a specific early-return path, an allocated working area was not
freed. Free it.
Change-Id: I7c8fe51ff475f191624086996be1c77251780b77
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4520
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32h7: Fix incorrect comment
The name of the bit according to the reference manual is inconsistency
error, not increment error.
Change-Id: Ie3b73c0312db586e35519e03fd1a5cb225673d97
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4521
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* target: fix 'bp' command help message
"asid" and "length" are separate arguments of the command.
Put space between them.
Change-Id: I36cfc1e3a01caafef4fc3b26972a0cc192b0b963
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4511
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Add ARM v8 AArch64 semihosting support
This patch implements semihosting support for AArch64. This picks
code from previously submitted AArch64 semihosting support patch
and rebases on top of reworked semihosting code. Tested in AArch64
mode on a Lemaker Hikey Board with NewLib and GDB.
Change-Id: I228a38f1de24f79e49ba99d8514d822a28c2950b
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4537
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* GDB fileIO stdout support
This patch fixes gdb fileio support to allow gdb console to be used as stdout.
Now we can do something like
gdb <inferior file>
(gdb) tar ext :3333
(gdb) load
(gdb) monitor arm semihosting enable
(gdb) monitor arm semihosting_fileio enable
(gdb) continue
Here: Output from inferior using puts, printf etc will be routed to gdb console.
Change-Id: I9cb0dddda1de58038c84f5b035c38229828cd744
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4538
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target: armv8: Avoid semihosting segfault on halt
Avoid a NULL pointer dereference when halting an aarch64 core.
Change-Id: I333d40475ab26e2f0dca5c27302a5fa4d817a12f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4593
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: target: Add NXP LS1012A config
As seen on the FRDM-LS1012A board.
Change-Id: Ifc9074b3f7535167b9ded5f544501ec2879f5db7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4594
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: board: Add NXP Freedom FRDM-LS1012A config
An update for the K20 CMSIS-DAP firmware can be found here:
https://community.nxp.com/thread/387080?commentID=840141#comment-840141
Change-Id: I149d7f8610aa56daf1aeb95f14ee1bf88f7cb647
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4595
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: only trigger once the event gdb-detach at gdb quit
When GDB quits (e.g. with "quit" command) we first execute
gdb_detach() to reply "OK" then, at GDB disconnect (either TCP
or pipe connection type), we execute gdb_connection_closed().
In case GDB is killed or it crashes, OpenOCD only executes the
latter when detects the disconnection.
Both gdb_detach() and gdb_connection_closed() trigger the event
TARGET_EVENT_GDB_DETACH thus getting it triggered twice on clean
GDB quit.
Do not trigger the event TARGET_EVENT_GDB_DETACH in gdb_detach()
and let only gdb_connection_closed() to handle it.
Change-Id: Iacf035c855b8b3e2239c1c0e259c279688b418ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4585
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* gdb_server: set current_target from connection's one
In a multi-target environment we are supposed to have a single
gdb server for each target (or for each group of targets within
a SMP node).
By default, the gdb attached to a server sends its command to
the target (or to the SMP node targets) linked to that server.
This is working fine for the normal gdb commands, but it is
broken for the native OpenOCD commands executed through gdb
"monitor" command. In the latter case, gdb "monitor" commands
will be executed on the current target of OpenOCD configuration
script (that is either the last target created or the target
specified in a "targets" command).
Fixed in gdb_new_connection() by replacing the current target
in the connection's copy of command context.
Change-Id: If7c8f2dce4a3138f0907d3000dd0b15e670cfa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4586
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/image: make i/j unsigned to avoid ubsan runtime error
src/target/image.c:1055:15: runtime error: left shift of 128 by 24 places cannot be represented in type 'int'
Change-Id: I322fd391cf3f242beffc8a274824763c8c5e69a4
Signed-off-by: Cody Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4584
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/stm32f7x: Clear stuck HSE clock with CSS
Change-Id: Ica0025ea465910dd664ab546b66f4f25b271f1f5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4570
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* psoc5lp: fix erase check, add free_driver_priv
psoc5lp_erase_check() was not properly adapted to the new
armv7m_blank_check_memory() in the hot fix 53376dbbed
This change fixes handling of num_sectors in dependecy of ecc_enabled.
Also add comments how ecc_enabled influences num_sectors.
Add pointer to default_flash_free_driver_priv() to all psoc5lp flash
drivers to keep valgrind happy.
Change-Id: Ie1806538becd364fe0efb7a414f0fe6a84b2055b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4569
Tested-by: jenkins
* target: atmel samd10 xplained mini
cortex m0+ on a tiny board, with an mEDBG (CMSIS-DAP) debug interface.
Change-Id: Iaedfab578b4eb4aa2d923bd80f220f59b34e6ef9
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: add SAMD11 Xplained Pro evaluation board
Change-Id: Id996c4de6dc9f25f71424017bf07689fea7bd3af
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4507
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Adds SAMD11D14AU flash support.
Corrects names of SAMD11D14AM and SAMD11D14ASS per datasheet.
Change-Id: I8beb15d5376966a4f8d7de76bfb2cbda2db440dc
Signed-off-by: Christopher Hoover <ch@murgatroid.com>
Reviewed-on: http://openocd.zylin.com/4597
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nds32: Avoid detected JTAG clock
AICE2 doesn't support scan for the maximum clock frequency of
JTAG chain. It will cause USB command timeout.
Change-Id: I41d1e3be387b6ed5a4dd0be663385a5f053fbcf9
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/4292
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl: Distinguish between sectors and blocks in status messages
Use the right word in flash protect command status messages based on
whether the target bank defines num_prot_blocks. Minor message style
tidy-up.
Change-Id: I5f40fb5627422536ce737f242fbf80feafe7a1fc
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4573
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* drivers: cmsis-dap: pull up common connect code
Just a minor deduplication
Change-Id: Idd256883e5f6d4bd4dcc18462dd5468991f507b3
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* drivers: cmsis-dap: Print version info when available
No need to wait until after connecting, might help diagnose part information by
printing earlier.
Change-Id: I51eb0d584be306baa811fbeb1ad6a604773e602c
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3404
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor: add support for TI MSP432 devices
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/at91sam4: fix sam4sa16c flash banks and its gpnvms count
There was already a github fork that had this fixed, but as we try
to use the latest, non-modified version of all software we use,
I would like to have this fix in the next releases of OpenOCD so
that if people uses $packagemanager, they will not have issues flashing
the last part of the flash of sam4sa16c chips.
Additionally, I've added some more logging related to the flash
bank that was used, and the chip ID that was detected.
Change-Id: I7ea5970105906e4560b727e46222ae9a91e41559
Signed-off-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4599
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* flash/nor/stm32lx: Add revision 'V' for STM32L1xx Cat.3 devices
Change-Id: Ic92b0fb5b738af3bec79ae335876aa9e26f5f4cd
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4600
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid null target->semihosting references.
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: Add HWID 0x139 (52832 rev E0)
Change-Id: I71b7471ccfcb8fcc6de30da57ce4165c7fb1f73f
Signed-off-by: James Jacobsson <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4604
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target: Fix segfault for 'mem2array'
Call 'mem2array' without arguments to reproduce the segmentation
fault.
Change-Id: I02bf46cc8bd317abbb721a8c75d7cbfac99eb34e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4534
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/armv7m_trace: Fix typo in enum
Change-Id: I6364ee5011ef2d55c59674e3b97504a285de0cb2
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3904
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/armv7m_trace: Use prefix for enums
Change-Id: I3f199e6053146a1094d96b98ea174b41bb021599
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3905
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/aarch64: Call aarch64_init_debug_access() earlier in aarch64_deassert_reset()
On Renesas R-Car, calling 'reset halt' and 'reset init' always made DAP inaccessible. Calling 'reset' and 'halt' seperatly worked fine.
The only differences seems to be the point in time when aarch64_init_debug_access() is called. This patch aligns the behaviour.
Change-Id: I2296c65e48414a7d9846f12a395e5eca315b49ca
Signed-off-by: Dennis Ostermann <dennis.ostermann@renesas.com>
Reviewed-on: http://openocd.zylin.com/4607
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* server: Improve signal handling under Linux
Commit 5087a955 added custom signal handlers for the openocd
server process.
Before this commit, when openocd is run as a background process
having the same controlling terminal as gdb, Control-C would be
handled by gdb to stop target execution and return to the gdb prompt.
However, after commit 5087a955, the SIGINT caused by pressing
Control-C also terminates openocd, effectively crashing the
debugging session. The only way to avoid this is run openocd in
a different controling terminal or to detach openocd from its
controlling terminal,
thus losing all job control for the openocd process.
This patch improves the server's handling of POSIX signals:
1) Keyboard generated signals (INT and QUIT) are ignored
when server process has is no controlling terminal.
2) SIGHUP and SIGPIPE are handled to ensure that .quit functions
for each interface are called if user's logs out of X
session or there is a network failure.
SIG_INT & SIG_QUIT still stop openocd
when it is running in the foreground.
Change-Id: I03ad645e62408fdaf4edc49a3550b89b287eda10
Signed-off-by: Brent Roman <genosensor@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3963
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* armv7a: read ttbcr and ttb0/1 at every entry in debug state
Commit bfc5c764df avoids reading
ttbcr and ttb0/1 at every virt2phys translation by caching them,
and it updates the cached values in armv7a_arch_state().
But the purpose of any (*arch_state)() method, thus including
armv7a_arch_state(), is to only print out and inform the user
about some architecture specific status.
Moreover, to reduce the verbosity during a GDB session, the
method (*arch_state)() is not executed anymore at debug state
entry (check use of target->verbose_halt_msg in src/openocd.c),
thus the state of translation table gets out-of-sync triggering
Error: Address translation failure
or even using a wrong address in the memory R/W operation.
In addition, the commit above breaks the case of armv7r by
calling armv7a_read_ttbcr() unconditionally.
Fixed by moving in cortex_a_post_debug_entry() the call to
armv7a_read_ttbcr() on armv7a case only.
Remove the call to armv7a_read_ttbcr() in armv7a_identify_cache()
since it is (conditionally) called only in the same procedure
cortex_a_post_debug_entry().
Fixes: bfc5c764df ("armv7a: cache ttbcr and ttb0/1 on debug
state entry")
Change-Id: Ifc20eca190111832e339a01b7f85d28c1547c8ba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4601
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Avoid dereferencing NULL pointer.
If a NULL pointer is passed, don't attempt to increment it. This avoids
passing the now not-NULL pointer on and eventually segfaulting. Also
remove some unnecessary temporary variables.
Change-Id: I268e225121aa283d59179bfae407ebf6959d3a4e
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4550
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Remove FSF mailing address.
Checkpatch complains about this (FSF_MAILING_ADDRESS).
Change-Id: Ib46a7704f9aed4ed16ce7733d43c58254a094149
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* drivers: cmsis_dap_usb: implement cmd JTAG_TMS
Simply add a wrapper around cmsis_dap_cmd_DAP_SWJ_Sequence()
Change-Id: Icf86f84b24e9fec56e2f9e155396aac34b0e06d2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4517
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* arm_adi_v5: put SWJ-DP back to JTAG mode at exit
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add RISC-V support.
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* usb_blaster: Don't unnecessarily go through DR-/IR-Pause
There is no need to pass through DR-/IR-Pause after a scan if we want to
go to DR-/IR-Update. We just have to skip the first step of the path to
the end state because we already did that step when shifting the last
bit.
v2:
- Fix comments as remarked in review of v1
Change-Id: I3c10f02794b2233f63d2150934e2768430873caa
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/4245
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* cortex_a: fix virt2phys when mmu is disabled
When the MMU is not enabled on debug state entry, virt2phys cannot
perform a translation since it is unknown whether a valid MMU
configuration existed before. In this case, return the virtual
address as physical address.
Change-Id: I6f85a7a5dbc200be1a4b5badf10a1a717f1c79c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4480
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* drivers: cmsis-dap: print serial if available
Helpful for sanity checking connections
Change-Id: Ife0d8b4e12d4c03685aac8115c9739a4c1e994fe
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3405
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: make a variable local
The vec_ids variable is not referenced anywhere other than the vector
catch command handler. Make it local to that function.
Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4606
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: fix compile error for uninitialized variable
Commit ad6c71e151 introduced the
variable "mmu_enabled" whose pointer is passed to cortex_a_mmu()
that initialises it.
This initialization is not visible to the compiler that issue
a compile error.
The same situation is common across the same file and the usual
workaround is to initialize it to zero; thus the same fix i
applied here.
Ticket: https://sourceforge.net/p/openocd/tickets/197/
Fixes: commit ad6c71e151 ("cortex_a: fix virt2phys when mmu is disabled")
Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4619
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* mips_m4k: add optional reset handler
In some cases by using SRST we can't halt CPU early enough. And
option PrRst is not available too. In this case the only way is
to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself.
For example by writing to some reset register.
This patch is providing possibility to use user defined reset-assert
handler which will be enabled only in case SRST is disabled. It is
needed to be able switch between two different reset variants on run
time.
Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4404
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target: add config for Qualcomm QCA4531
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable
Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4405
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add config for 8devices LIMA board
More information about this board can be found here:
https://www.8devices.com/products/lima
Change-Id: Id35a35d3e986630d58d37b47828870afd107cc6a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4406
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target|board: move common AR9331 code to atheros_ar9331.cfg
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add DDR2 helper
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add documentation and extra helpers
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add DPTechnics DPT-Board-v1
it is Atheros AR9331 based IoT dev board.
Change-Id: I6fc3cdea1bef49c53045018ff5acfec4d5610ba6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4424
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* fpga/altera-10m50: add all device id
add all currently know Intel (Alter) MAX 10 device ids
Change-Id: I6a88fef222c8e206812499d41be863c3d89fa944
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4598
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target|board: Add Intel (Altera) Arria 10 target and related board
Target information about this SoC can be found here:
https://www.altera.com/products/fpga/arria-series/arria-10/overview.html
Achilles Instant-Development Kit Arria 10 SoC SoM:
https://www.reflexces.com/products-solutions/development-kits/arria-10/achilles-instant-development-kit-arria-10-soc-som
Change-Id: Id78c741be6a8b7d3a70f37d41088e47ee61b437a
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4583
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/riscv: fix compile error with gcc 8.1.1
Fix compile error:
src/target/riscv/riscv-011.c: In function ‘slot_offset’:
src/target/riscv/riscv-011.c:238:4: error: this statement may fall through
[-Werror=implicit-fallthrough=]
switch (slot) {
^~~~~~
src/target/riscv/riscv-011.c:243:3: note: here
case 64:
^~~~
Fixes: a51ab8ddf6 ("Add RISC-V support.")
Change-Id: I7fa86b305bd90cc590fd4359c3698632d44712e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4618
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* server: explicitly call "shutdown" when catch CTRL-C or a signal
Every TCL command can be renamed (or deleted) and then replaced by
a TCL proc that has the same name of the original TCL command.
This can be used either to completely replace an existing command
or to wrap the original command to extend its functionality.
This applies also to the OpenOCD command "shutdown" and can be
useful, for example, to set back some default value to the target
before quitting OpenOCD.
E.g. (TCL code):
rename shutdown original_shutdown
proc shutdown {} {
puts "This is my implementation of shutdown"
# my own stuff before exit OpenOCD
original_shutdown
}
Unfortunately, sending a signal (or pressing CTRL-C) to terminate
OpenOCD doesn't trigger calling the original "shutdown" command
nor its (eventual) replacement.
Detect if the main loop is terminated by an external signal and
in such case execute explicitly the command "shutdown".
Replace with enum the magic numbers assumed by "shutdown_openocd".
Please notice that it's possible to write a custom "shutdown" TCL
proc that does not call the original "shutdown" command. This is
useful, for example, to prevent the user to quit OpenOCD by typing
"shutdown" in the telnet session.
Such case will not prevent OpenOCD to terminate when receiving a
signal; OpenOCD will quit after executing the custom "shutdown"
command.
Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4551
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* zy1000: fix compile error with gcc 8.1.1
The fall-through comment is not taken in consideration by gcc 8.1.1
because it is inside the braces of a C-code block.
Move the comment outside the C block.
Change-Id: I22d87b2dee109fb8bcf2071ac55fdf7171ffcf4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4614
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl.c: fix flash bank bounds check in 'flash fill' command handler
Steps to reproduce ( STM32F103 'Blue Pill', 128KiB of flash ):
> flash fillh 0x0801FFFE 00 1
wrote 2 bytes to 0x0801fffe in 0.019088s (0.102 KiB/s)
> flash fillw 0x0801FFFE 00 1
Error: stm32f1x.cpu -- clearing lockup after double fault
Error: error waiting for target flash write algorithm
Error: error writing to flash at address 0x08000000 at offset 0x0001fffe
Change-Id: I145092ec5e45bc586b3df48bf37c38c9226915c1
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4516
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: add command "dpreg"
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.
Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
$dap_name dpreg reg [value]
Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: add free_driver_priv
Change-Id: I429a9868deb0c4b51f47a4bbad844bdc348e8d21
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/4608
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: add support for NuttX
This patch introduces RTOS support for NuttX. Currently,
only ARM Cortex-M (both FPU and FPU-less) targets are supported.
To use, add the following lines to ~/.gdbinit.
define hookpost-file
eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end
And please make sure the above values are the same as in
src/rtos/nuttx_header.h
Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com>
Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com>
Reviewed-on: http://openocd.zylin.com/4103
Tested-by: jenkins
Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* server/server: Add ability to remove services
Add the ability to remove services while OpenOCD is running.
Change-Id: I4067916fda6d03485463fa40901b40484d94e24e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4054
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: fix incorrect comment
The code sets C_MASKINTS if that bit is not already set (correctly). Fix
the comment to agree.
Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4620
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target/stm32f0x: Allow overriding the Flash bank size
Copy & paste from another stm32 target.
Change-Id: I0f6cbcec974ce70c23c1850526354106caee1172
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4575
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/target: add Allwinner V3s SoC support
Change-Id: I2459d2b137050985b7301047f9651951d72d9e9e
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4427
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/arm_adi_v5: allow commands apsel and apcsw during init phase
The current implementation of apsel cannot be executed during the
initialization phase because it queries the DAP AP to retrieve and
print the content of IDR register, and the query is only possible
later on during the exec phase.
But IDR information is already printed by the dedicated command
apid, making redundant printing it by apsel too.
Being unable to run apsel during initialization, makes also apcsw
command (that depends on apsel) not usable in such phase.
Modify the command apsel to only set the current AP, without making
any transfer to the (possibly not initialized yet) DAP. When run
without parameters, just print the current AP number.
Change mode to COMMAND_ANY to apsel and to apcsw.
Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4624
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: allow command dacrfixup during init phase
There is no reason to restrict the command "cortex_a dacrfixup"
to the EXEC phase only.
Change the command mode to ANY so the command can be used in
the initialization phase too.
Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4623
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/armv7a_cache: add gdb keep-alive and fix a missing dpm finish
Depending on range size, the loop on cache operations can take quite
some time, causing gdb to timeout.
Add keep-alive to prevent gdb to timeout.
Add also a missing dpm->finish() to balance dpm->prepare().
Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4627
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add detail to `wrong register size` error.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Id31499c94b539969970251145e42c89c943fd87c
Reviewed-on: http://openocd.zylin.com/4577
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* doc: fix typo in cortex_m maskisr command
Change-Id: I37795c320ff7cbf6f2c7434e03b26dbaf6fc6db4
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4621
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: restore C_MASKINTS after reset
The cortex_m maskisr user-facing setting is not changed across a target
reset. However, the in-core C_MASKINTS bit was always cleared as part of
reset processing, meaning that a cortex_m maskisr on setting would not
be respected after a reset. Set C_MASKINTS based on the user-facing
setting value rather than always clearing it after reset.
Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4605
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: update all uses of interface/stlink-v2-1 to interface/stlink
Change-Id: I5e27e84d022f73101376e8b4a1bdc65f58fd348a
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4456
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/riscv/riscv-011: fix compile warning about uninitialized variable
In MSYS2 MinGW 64-bit
git clone git://git.code.sf.net/p/openocd/code openocd
$ gcc --version
gcc.exe (Rev1, Built by MSYS2 project) 8.2.0
./bootstrap
./configure --prefix=
$ cat config.status | grep CFLAGS
CFLAGS='-g -O2'
make bindir = "bin-x64"
depbase=`echo src/target/riscv/riscv-011.lo | sed 's|[^/]*$|.deps/&|;s|\.lo$||'`;\
/bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF $depbase.Tpo -c -o src/target/riscv/riscv-011.lo src/target/riscv/riscv-011.c &&\
mv -f $depbase.Tpo $depbase.Plo
libtool: compile: gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF src/target/riscv/.deps/riscv-011.Tpo -c src/target/riscv/riscv-011.c -o src/target/riscv/riscv-011.o
src/target/riscv/riscv-011.c: In function 'poll_target':
src/target/riscv/riscv-011.c:1799:6: error: 'reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
reg_cache_set(target, reg, ((data & 0xffffffff) << 32) | value);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/target/riscv/riscv-011.c:1686:17: note: 'reg' was declared here
unsigned int reg;
^~~
cc1.exe: all warnings being treated as errors
make[2]: *** [Makefile:3250: src/target/riscv/riscv-011.lo] Error 1
Change-Id: I6996dcb866fbace26817636f4bedba09510a087f
Signed-off-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
Reviewed-on: http://openocd.zylin.com/4635
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Checkpatch complains about this (FSF_MAILING_ADDRESS).
Change-Id: Ib46a7704f9aed4ed16ce7733d43c58254a094149
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Added cc3220sf flash driver to support the TI CC3220SF
microcontrollers. Implemented flash driver to support the
internal flash of the CC3220SF. The implementation does not
support the serial flash of the CC32xx family that requires
connection over UART, and not via JTAG/SWD debug. Added config
files for both CC32xx devices (no flash) and CC3220SF (with
flash).
Updated to implement comments from code review.
Additional updates to handle remaining comments from review.
Additional updates per review.
Added code to only request aligned writes and full 32-bit
words down to flash helper algorithm. Updated for recent
changes in OpenOCD flash code.
Removed cc32xx.cfg file made obsolete by this patch.
Change-Id: I58fc1478d07238d39c7ef02339f1097a91668c47
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4319
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for the XDS110 debug probe using the APIs in the
probe's firmware. Includes support for older versions of the
firmware (with reduced performance) and support for a newer
version that includes OpenOCD specific APIs. Tested on various
TI LauchPads including MSP432P4, MSP432E4, CC2650, CC2652, and
CC3220SF.
Updated to add better support for swd switch. Removed issues found with
clang static analysis.
Updated to add rules entry for the XDS110 probe and Tiva DFU mode (which
affects both XDS110 and ICDI probes).
Change-Id: Ib274143111a68e67e80003797c6a68e3e80976b2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4322
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
It was giving this error:
ERROR: Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. OpenOCD already
includes a copy of the GPL.
Change-Id: Iae50c2b38f1845d826d7d631072c8c3ded8859da
Flash loaders refactored to the new style - use generated .inc
instead of hexadecimal machine code in the flash driver source.
Change-Id: If65a2099589e210f9450819b467d67819fd841fc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4439
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Flash loaders refactored to the new style - use generated .inc
instead of hexadecimal machine code in the flash driver source.
Change-Id: If65a2099589e210f9450819b467d67819fd841fc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4439
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:
1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:
The previous logic was erroneous. The delay in clock cyles from a bit
written to the jtag interface to a bit read by the jtag interface is:
* The number of BYPASSed TAPs before this (jtagspi) tap
* The length of the jtagspi data register (1)
* The number of BYPASSed TAPs before this one.
I.e. it is just the number of enabled TAPs. This also gets rid of the
configuration parameter DR_LENGTH.
3. Use marker bit to start spi transfer
If there are TAPs ahead of this one on the JTAG chain, and we are in
DR-SHIFT, there will be old bits toggled through first before the first
valid bit destined for the flash.
This delays the begin of the JTAGSPI transaction until the first high bit.
4. New jtagspi protocol
A JTAGSPI transfer now consists of:
* an arbitrary number of 0 bits (from BYPASS registers in front of the
JTAG2SPI DR)
* a marker bit (1) indicating the start of the JTAG2SPI transaction
* 32 bits (big endian) describing the length of the SPI transaction
* a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
* an arbitrary number of cycles (to shift MISO/TDO data through
subsequent BYPASS registers)
5. xilinx_bscan_spi: clean up, add ultrascale
This is tested on the following configurations:
* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E
Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When both SRST and TRST asserted, 'u' is sent to remote bitbang.
Fix for correct handling of such a case
Change-Id: I2a93ff71f5bbae658e6c0c3649a9fbcca2c5a14b
Signed-off-by: Aleksey Shargalin <myokaski@gmail.com>
Reviewed-on: http://openocd.zylin.com/4283
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds support for Blue Gecko and Mighty Gecko chips from
Silabs.
They have different EFM32_MSC_REGBASE and LOCK register offset.
Based on the original patch from Andreas Kemnade.
Change-Id: I166c14960ced7c880b68083badd1b31372fefabe
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-on: http://openocd.zylin.com/4034
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: chrysn <chrysn@fsfe.org>
Active watchdog forces reset during armv7m_checksum_memory()
in verify_image command if run just after reset init.
COP watchdog in KL series and WDOG32 in KE1 series
have longer timeout however they need to be disabled too.
The change extends 'kinetis disable_wdog' command to optionally
probe the chip and use appropriate algorithm to disable watchdog.
Setting of cache type is also split from flash_support flags.
Tcl command 'kinetis disable_wdog' is called in reset-init event.
Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3901
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Udev rules for Ambiq Micro ftdi based EVK's.
Two new vid:pid's: 2AEC:6010, and 2AEC:6011.
Udev rule for multi-target Debug board 2AEC:1106
Change-Id: Id7430d0c70647752375230f4024be9f7a2ba95ce
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3980
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Fix "couldn't use loader, falling back to page memory writes" error on
stm32l0 which was caused by the use of cortex-m3 instructions in the
flash loader code. The loader is rewritten using cortex-m0 compatible
instructions
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Change-Id: If23027b8e09f74e45129e1f8452a04bb994c424e
Reviewed-on: http://openocd.zylin.com/4036
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Modern desktop systems with systemd recommend this way to give users
access to devices. We change permissions to sane value along the way.
See e.g. https://lists.debian.org/debian-devel-announce/2016/11/msg00008.html
We also change the filename to put it in order with 71-seat.rules, 60
is default for dh_installudev so pick that as a reasonable value.
Change-Id: I15f6fb1b6be853ac097d0ca91955609f9e5eb9cf
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/2804
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Avoid special rules to generate array at compile time by shipping
the generated file. Convert to Makefile build like the other
loaders.
Change-Id: I5a05edddcfaff3d395086cd3aa33120f8a7aa9dc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3864
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch introduces RTOS support for uC/OS-III. Currently, only
FPU-less ARM Cortex-M targets are supported. Due to the configurability
of the RTOS, an OpenOCD-specific file must be linked along with the
project to determine the correct offsets within the OS_TCB structure.
In addition to the above, a crash was fixed in rtos_get_gdb_reg_list
such that RTOS support could be used between resets without restarting
OpenOCD and support for the Hg packet was cleaned up.
Change-Id: Ide004a689e6b886185df665c00fb644629eb31d1
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3556
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* port to new migen
* streamline package/part specification
* add pullup (Series3, Series6) and pullnone (Series7) for unused pins
as xilinx impact/vivado do it.
* specify respective toolchains
* build Series7 with vivado (broader support, faster)
* point to prebuilt bitstreams at https://github.com/jordens/bscan_spi_bitstreams
Change-Id: Ibfef3d78f855b754425f3e6131e2e49fa111e09a
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/3173
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Robert Jördens
Reviewed-by: William D. Jones
Reviewed-by: Tim "mithro" Ansell <mithro@mithis.com>
arm-none-eabi target triplet defaults to Little Endian, and so far any
submitted machine code snippets have been verified to be Little Endian.
However a user might override [ARM_]CROSS_COMPILE with an armeb toolchain,
potentially resulting in invalid machine code.
Let's be safe and enforce Little Endian mode for assembler and compiler.
Change-Id: I9cefe24689eaded25d60ffb1f254b254e8d76f9d
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3498
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Instead of using ARM_ prefixed variables and an "arm" target,
use CROSS_COMPILE, AS, OBJCOPY. This requires to switch from ?= to =
to avoid the host assembler getting invoked.
This allows to handle kinetis_ke subdirectory like fm4 and xmc1xxx.
Change-Id: I7ea0bf119f6c4716f4d6002794004730af49eef4
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3505
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add a Makefile that orchestrates the other loader Makefiles.
It assumes that the clean target can be run without cross toolchain.
at91sam7x does not successfully build and is not really needed either,
therefore left out.
Add an exception to .gitignore for any contrib/loaders Makefile.
Change-Id: I74456b768472f3190a1721bcf41a777bb8daf973
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3504
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv4_5_crc.inc, and convert the code to target
endianness the least intrusive way.
Change-Id: I7452b2c7e679dae14f9cda5f89bc81c16fc12cad
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3473
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Add rules to build armv4_5_erase_check.inc, and convert the code to
target endianness the least intrusive way.
Drop an unused word from the assembler sources to make the ARM bytecode
fully match that of armv4_5.c and to not break ARMv4 assumptions.
This completes the build rules for contrib/loaders/erase_check directory.
Change-Id: I36be7a944e26142088195fa3fb072d4e577bf328
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3135
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv7m_crc.inc and include it via preprocessor.
Change-Id: I4482c7acb8454de28bdf210d9f06c0720ada490a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The original ULINK adapter has been introduced by Keil in 2002 and got
replaced in 2008 by the incompatible ULINK2. It is not listed on their
website any more. For information about it, browse archive.org
for http://www.keil.com/ulink1/ or http://www.keil.com/ulink/
Change-Id: Ie52d381580acab53ddb40499594dbdc2d27ef1b6
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3371
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This udev rule makes the Altera USB Blaster clone I have on my desk
accessible to the plugdev group.
Change-Id: Ic5e8052c66a270b6a6f89e29de49d9785f18fc1e
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/3423
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Cortex-M0+ and M4 motor control MCUs KV10, KV11, KV30, KV31,
KV42, KV44 and KV46 added to SDID identification.
Watchdog disable code changed to work on Cortex-M0+ (KV1x)
Protection size set to 1K for 16K flash devices (KV10Z16)
- cherry picked from Andrey Smirnov's change #2051
Change-Id: Ia6f4868eaf7e2cb6ad6a736210c703a67e0027be
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3235
Tested-by: jenkins
Reviewed-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Old code waited only for 7 bytes and didn't handle buffer wrap-around, but
was functional despite.
Change-Id: Iceaf7be1e51368b2ec0a8722cc9ac16d12f9aa63
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3140
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tim Newsome
Antonio Borneo
Steven Stallion
Kevin Gillespie
Edward Fewell
Tomas Vanek
Michele Sardo
Robert Jordens
Aleksey Shargalin
Ake Rehnman
Alexandre Torgue
Andrea Merello
Forest Crossman
Karl Palsson
Armin van der Togt
Jiri Kastner
Andreas Fritiofson
Andreas Färber
Alexander Kurz
Christopher Head
Uwe Bonnes