This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This makes the messages consistent with most of the rest of
the OpenOCD output.
Change-Id: I915a01187e7fc317e02483ac0bbd39ec077d6321
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Made sure that also outgoing GDB packets are logged,
not only the incoming ones.
- Improved the treatment of non-printable characters
in the packets to make it more robust.
Prior to this change:
- Outgoing packets were not printed unless OpenOCD was
re-compiled with _DEBUG_GDB_IO_.
- Non-prinable characters were only treated in incoming
'X' packets.
After this change:
- Both incoming and outgoing GDB packets are logged
on debug_level >= 3, so that both directions of the
GDB channel are visible.
- Non-printable characters are checked for in every packet
so that hey do not interfere with the terminal.
Change-Id: I0613e57ae5059b3279b0abcb71276cf5719a8699
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Without such reference, it could be difficult to find the example.
Change-Id: Ia9ffb06bc1a45446c2c7b53197ab3400e1d8a9e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6281
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Main improvement is in the doxygen comments.
Minimize the delta with kernel file.
Skip the functions hlist_unhashed_lockless() and
__list_del_clearprev() that are relevant only in kernel.
Remove gcc extension "omitted conditional operand".
Change-Id: I2e9ddb54cfe2fa5f7cf18f44726acd144e1f98b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6276
Reviewed-by: <rdiezmail-openocd@yahoo.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Current autocomplete filters-out some command reported by "info
commands". One of the filter rule concerns the command's private
data.
Every command registered by OpenOCD has its 'struct command' as
private data.
By ignoring commands without private data, we loose several TCL
commands registered by jimtcl, e.g. 'foreach', 'llength'.
By assuming that every command with non-NULL private data has
'struct command' as private data, we risk at best to access
inconsistent data, at worst to trigger a segmentation fault.
Export the already available functions:
- to check if a command has been registered by OpenOCD and
- to get the private data.
While there, rename jimcmd_is_ocd_command() as
jimcmd_is_oocd_command().
Don't filter-out jimtcl commands with no private data.
Check the private data only on OpenOCD commands.
Change-Id: Ib5bf8d2bc5c12440c0cfae438f637c38724a79b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6282
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
The helper jim-nvp does not comply with OpenOCD coding style due
to typedef of struct and CamelCase symbol names.
While it's trivial fixing the helper and all its current use in
the code, changing these APIs will potentially break a number of
patches pending in gerrit. Gerrit will not trigger any alert, but
the code will generate compile error after the merge.
Add the compile flag "-Wno-error=deprecated-declarations" to keep
as warning (not as error) the use of "deprecated" functions and
types.
Rename all the CamelCase symbols is lowercase and provide struct
prototypes in place of the typedef.
Add a DEPRECATED section to 'jim-nvp.h' where the old CamelCase
symbols and the old typedef are re-declared with compile attribute
'deprecated'.
With this change OpenOCD compiles, but generates warnings.
The remaining changes allover OpenOCD code will be fixed in a
separate patch for easier review.
The patches merged later that still use the old deprecated API
will compile with warnings. This will permit to identify and fix
these cases.
Change-Id: I786385d0f662dbb1be5be313ae42623156d68ce5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6183
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The memory allocated to hold the watchpoints is not freed at
OpenOCD exit.
Free the watchpoint memory at OpenOCD exit.
Change-Id: I518c9ce0dc901cde2913d752e3154734f878b854
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6210
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Use byte address select for 1 and 2 bytes length.
Use normal mode for 4 bytes length.
Change-Id: I28d182f25145d0635de64d0361d456f1ad96640e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6197
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Decrement the available watchpoints only when succeed setting it.
Initialize the available watchpoint with the correct value.
Change-Id: I0f93b347300b8ebedbcd9e718d4ba32b26cf6846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6196
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current implementation of OpenOCD does not support watchpoints for
cortex_a architecture. So, I replaced the add_watchpoint and
remove_watchpoint with the specific implementation for the
cortex a and using the breakpoint implementation and the arm
documentation [1] as reference. In particular, I have made the
following changes:
* added the following functions
- cortex_a_add_watchpoint
This wrapper function check whether there are any watchpoint
available on the target device by calling cortex_a_set_watchpoint.
- cortex_a_set_watchpoint
This function is responsible for settings the watchpoint register
pair. In particular, it sets the WVR and the WCR registers with
the cortex_a_dap command.
- cortex_a_remove_watchpoint
This wrapper function the selected watchpoint on the target device
by calling cortex_a_unset_watchpoint.
- cortex_a_unset_watchpoint
This function sets both the WVR and the WCR registers to zero, thus
unsetting the watchpoint.
[1]
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0464f/BCGDHIEJ.html
Change-Id: I86611dab474cb84836662af572b17636dc68e282
Signed-off-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Reviewed-on: http://openocd.zylin.com/3913
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
When a WAIT occurs the commands after the WAIT are replayed and the
STICKYORUN is cleared. However if another WAIT occurs during the
command replay, the command itself is resent but the STICKYORUN bit
shall also be cleared. If this is not done, the MEM-AP hangs.
Change-Id: I14e8340cd5d8f58f4de31509da96cfa2ecb630d1
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6278
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The corresponding bit for each macro is changed, but this is not
relevant in the code.
Change-Id: I7039464f5a3d55d008208f44952aadeb815bd5a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6212
Tested-by: jenkins
The implementation of command 'usage' is broken while checking the
line limit of 76 chars per line (e.g. 'usage load_image') and the
line wrapping is not correct. The same broken code is used for the
first output line of command 'help' too.
When call command_help_show_wrap(), include the command's name in
the string so the whole text would be wrapped.
Change-Id: Idece01ce54994db7e851d8522435ff764b11f3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6223
Tested-by: jenkins
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
Use the existing macro ARRAY_SIZE().
Rewrite the functions rtos_type.create() to simplify the logic.
Change-Id: I8833354767045d1642801d26944c9087a77add00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6261
Tested-by: jenkins
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Replace the custom macro dimof() with the OpenOCD macro
ARRAY_SIZE().
Change-Id: I2fe638444f6c16f2a78c1fd558b21550f76282d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6259
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
The target mem_ap appears as an ARM target, thus it allows the
execution of ARM specific commands causing the crash of OpenOCD.
E.g. 'arm mrc ...' can be executed and segfaults.
Replace the incorrect ARM magic number with a dedicated one.
While there, remove the 'struct arm', that is now holding only the
mem_ap's dap, and replace it with a pointer to the dap.
Change-Id: I881332d3fdf8d8f8271b8711607737b052a5699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6213
Tested-by: jenkins
Commit e216186fab ("helper/command: register full-name commands
in jim") and commit a7d68878e4 ("helper/command: unregister
commands through their full-name") introduce a LOG_DEBUG() message
each for command registration and unregistration.
The messages above are quite noisy and pollute the log when
debug_level is 3 or higher.
They can be useful to debug the command registration logic, but
for the other debug activities on OpenOCD are just noisy.
Already commit a03ac1ba30 ("helper/command: disable logging of
registered commands [RFC]") was merged to silent the first case
that is now back with additional logs.
Silent both log messages.
Use 'if (false)' to silent them, making easy to re-enable it when
or if someone needs it.
Change-Id: Id8a067e60e822d4ecbddcb036d081298f7e6181f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6220
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I101c76a638805d77c1ff356cf0f027552389e5d3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6216
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
The early documentation for armv8a report the debug register WFAR
as containing the address of the instruction that triggered the
watchpoint. More recent documentation report the register EDWAR as
containing the data memory address that triggered the watchpoint.
The name of macros CPUV8_DBG_WFAR0 and CPUV8_DBG_WFAR1 is not
correct as they point to the debug register EDWAR, so reading such
register returns directly the data memory address that triggered
the watchpoint. The code incorrectly passes this address value to
the function armv8_dpm_report_wfar(); this function is supposed to
adjust the PC value, decrementing it to remove the effects of the
CPU pipeline. This pipeline offset, that has no meaning on the
value in EDWAR, caused commit 651b861d5d ("target/aarch64: Add
watchpoint support") to add back the offset while comparing the
address with the watchpoint enabled.
The upper 32 bits of EDWAR are not valid in aarch32 mode and have
to be ignored.
Rename CPUV8_DBG_WFAR0/1 as CPUV8_DBG_EDWAR0/1.
Remove the function armv8_dpm_report_wfar().
Remove the offset while searching the matching watchpoint.
Ignore the upper 32 bits of EDWAR in aarch32 mode.
Fix a comment and the LOG text.
Change-Id: I7cbdbeb766fa18e31cc72be098ca2bc501877ed1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6205
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
The field 'wp_pc' was originally introduced in commit 55eeea7fce
("ARMv7a/Cortex-A8: report watchpoint trigger insn") in end 2009
to contain the address of the instruction which triggered a
watchpoint. Later on with commit 651b861d5d ("target/aarch64:
Add watchpoint support") it has been reused in to hold directly
the memory address that triggered a watchpoint.
Rename 'wp_pc' as 'wp_addr' and change its doxygen description.
While there, fix the format string to print the field.
Change-Id: I2e5ced1497e4a6fb6b38f91e881807512e8d8c47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6204
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Compile fails with error:
src/jtag/drivers/cmsis_dap.c:683:28: error: format specifies type
'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
" received 0x%" PRIx8, CMD_DAP_TFER, resp[0]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
Fix the format specifier.
Change-Id: I0a5a1a35452d634019989d14d849501fb8a7e93a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6255
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Despite of assert(is_packed) clang static analyser complains on use
of the uninitialized offset variable.
Cross compiling with latest x86_64-w64-mingw32-gcc hits warnings
src/target/armv7m.c: In function ‘armv7m_read_core_reg’:
src/target/armv7m.c:337:54: error: ‘reg32_id’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
It happens because mingw32 defines assert() without the attribute
"noreturn", whatever NDEBUG is defined or not.
Replace assert(is_packed) by if (is_packed) conditional and call
assert(false) in the else branch.
Change-Id: Id3c7dcccb65106e28be200b9a4d2b642f4d31019
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
The workaround for jimtcl 0.80 in commit 36ae487ed0 ("jimtcl:
add temporary workaround for memory leak in jimtcl 0.80") issues a
compile time error on macOS:
../src/helper/command.c:157:22: error: aliases are not
supported on darwin
__attribute__((weak, alias("workaround_createcommand")));
The OS is x86_64-apple-darwin19.6.0 and the compiler used is
x86_64-apple-darwin13.4.0-clang.
Restrict the workaround on Linux host only. The fix for 'expr'
syntax change is already merged and the workaround will be dropped
soon.
Change-Id: I925109a9c57c05f8c95b70bc7d6604eb1172cd79
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adam Jeliński <ajelinski@users.sourceforge.net>
Fixes: 36ae487ed0 ("jimtcl: add temporary workaround for memory leak in jimtcl 0.80")
Fixes: https://sourceforge.net/p/openocd/tickets/304/
Reviewed-on: http://openocd.zylin.com/6241
Tested-by: jenkins
Both GDB commands "target remote" and "target extended-remote" require
to have ":" right before port number.
e.g.
(gdb) target extended-remote :3333
Add ":" to the warning message so that users can copy & past it.
Change-Id: Id6d8ec1e4dfd3c12cb7f3b314064f2c35fa7ab55
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6237
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
We have TCL procedure and commands that we do not want to show in
the list of auto-completion. E.g. TCL wrappers for deprecated
commands, internal procedures that are not supposed to be exposed
to user, or even commands that the user decides to hide.
Create a TCL procedure to be called by telnet auto-complete code
in place of the hard-coded TCL command. The procedure will run the
same command and will filter-out the unwanted command names.
Initialize the list of commands to be filtered-out with the name
of the TCL procedure above, as it is considered as internal.
Change-Id: I2d83bbf8194502368c589c85cccb617e69128c69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6194
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
this change aims to provide a better gdb debugging experience,
by making gdb understand what's really happening.
before this change when hitting a watchpoint
- openocd reports "T05" to gdb
- gdb displays: Program received signal SIGTRAP, Trace/breakpoint trap.
after the change
- openocd reports "T05watch:20000000;" to gdb
- gdb displays:
Hardware watchpoint 1: *0x20000000
Old value = 16000000
New value = 170000000
...
Change-Id: Iac3a85eadd86663617889001dd04513a4211ced9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6181
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Nowadays, when it's difficult to buy STM32F030,
the use of GD32F130 seems to be an interesting functional alternative.
This is cortex-M3 and it works with the stm32f1x driver, but unfortunately not fully.
The main difference is another offset of user option bits
(like WDG_SW, nRST_STOP, nRST_STDBY) in option byte register
(FLASH_OBR/FMC_OBSTAT 0x4002201C).
Any use of functions like lock or unlock results in change default values of the those bits stored in flash.
Thus broken microcontroller is malfunctioning, e.g. flash block programming is interrupted
by unexpected active hardware watchog (after 0.4s).
This patch is a simplified version of #4592 done by Dominik Peklo (http://openocd.zylin.com/#/c/4592/).
GigaDevice GD32F1x0 & GD32F3x0 series devices share DEV_ID
with STM32F101/2/3 medium-density line,
however they use a REV_ID different from any STM32 device,
so can be succesfully detected.
Change-Id: I252cdf738d94983b70676a3497326f90c329e292
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Reviewed-on: http://openocd.zylin.com/6164
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a use of AH_BOTTOM from configure.ac. This macro is used by
autoheader to add '#include' of some include file to the end of
config.h.in and then to config.h. OpenOCD can be built with a custom
config.h, so it's preferable to move these '#include' statement directly
in the C files that need them dropping this unneeded dependency.
It also causes problems when I want to use the gnulib library (which
comes with its own Makefile, and does not have the same include path as
the top-level Makefile).
So this change touches a lot of files, but is actually really simple. It
does not affect functionality at all.
Change-Id: I52c70bf15eb2edc1dd10e0fde23b2bcd4caec000
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/6171
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Currently, all drscan commands will cycle through DR-PAUSE before reaching
TAP-IDLE. This patch provides a different path on FTDI driver.
This change is required for the ST On Chip Emulator (OnCE), to avoid
re-enabling the OnCE tap after every DRSCAN. This is because the OnCE
TAP (see ST Application Note AN4035) gets disabled if DR-PAUSE is entered
before DR-UPDATE.
With this commit, the current path:
DR-SHIFT -> DR-EXIT1 -> DR-PAUSE -> DR-EXIT2 -> DR-UPDATE -> IDLE
is changed to:
DR-SHIFT -> DR-EXIT1 -> DR-UPDATE -> IDLE
only if IDLE is the endstate (which is the driver default).
Before this patch, once the SHIFT sequence is complete, the driver would
normally move to the nearest stable state, which is DR-PAUSE, by clocking
out a '10' binary sequence. Then it would follow the path provided by
tap_get_tms_path() to reach endstate. It is done this way because
tap_get_tms_path() only supports stable states.
After this patch, the strategy is mostly the same, with the exception that,
if TAP_IDLE is the endstate, a '110' binary sequence is output after completing
the SHIFT sequence. This takes the TAP directly to IDLE, with no further action
required.
A scheme of the DR chain is shown below. A * character is used to mark the
stable states.
----------------------------------------------------------------------
| | 0
v 1 0 0 1 0 1 1 |
IDLE* -> SEL-DR -> CAPTURE -> SHIFT* -> EXIT1 -> PAUSE* -> EXIT2 -> UPDATE
| ^
1 | |
-----------------------------
Change-Id: Ib413e5c4c0bbf75dae0b4672119bae4ef03d0258
Signed-off-by: Luis de Arquer <luis.dearquer@inertim.com>
Reviewed-on: http://openocd.zylin.com/6123
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
auto-completion behavior:
- if there is only one matched command complete the user-command
- else if multiple matches add the common part then in second step
list all matched commands
- sub-commands are handled in the same way
- auto-completion restarts after these characters ';', '[', '{'
Change-Id: I1b81dd19191a5785e68d0bb5cd244e01a4dd0587
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6095
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The documentation of Jim_SetResultFormatted() reports that the jim
objects passed as arguments would be freed if have zero refcount.
Remove the useless Jim_IncrRefCount()/Jim_DecrRefCount().
Remove the dangerous Jim_FreeNewObj() that should trigger a double
free(). Not tested due to lack of aice adapter.
While there, rename some CamelCase symbol.
Change-Id: Ic56704c83d6391c38f6b0efa6566784d453bc0fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6190
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 7a731eb637 ("Added HostOS variable"), merged in 2009,
adds a TCL global variable 'ocd_HostOS' that reports in a string
the OS of the host.
This was proposed as a workaround for jimtcl that didn't define
the standard TCL variable 'tcl_platform(os)'.
With commit 42f3fb7b7f46 ("Determine platform_tcl() settings with
configure"), merged in 2010 and part of jimtcl 0.70 issued in
early 2011, jimtcl provides the requires TCL standard variable
'tcl_platform(os)'.
The variable 'ocd_HostOS' has never been used by any TCL script
distributed with OpenOCD.
Drop the TCL variable 'ocd_HostOS'.
Change-Id: I27858de35cc9d30df97145ca1ccd24877be4af11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6189
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If malloc() fails, the just allocated Jim_Obj will leaks.
Move Jim_IncrRefCount() before the malloc() and deallocate the Jim
object with Jim_DecrRefCount() on malloc() fail.
While there, add the 'out of memory' log and fix the CamelCase
name of the symbol tclOutput.
Change-Id: Ic733db229d5aa5d477d758ea9cb88cd81d7542cd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6188
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The files jim-nvp.[ch] were originally inside jimtcl, then in 2011
they were dropped by jimtcl and integrated in OpenOCD.
The initial purpose was to make them as an independent library,
thus the presence of an 'init' function. Being now part of OpenOCD
do not require the 'init' function anymore, that is still empty
and unused, plus its name is in violation of the coding style.
Drop the function Jim_nvpInit().
Change-Id: I429e10444c86a26dbdc22aa071315324dc5edc3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6187
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Accordingly to OpenOCD coding style, both typedef and Camelcase
symbols are forbidden.
The type '_Bool' is not used in the code, having 'bool' as
preferred choice.
Remove the definition of '_Bool' from 'types.h'.
Change-Id: I8863f9836ccd9166e0c69fa5d75d6fef79ae7bfb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6186
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The ELF typedef's 'Elf32_Sword' and 'Elf32_Hashelt' are not used
within OpenOCD. Plus, being their name in CamelCase require extra
effort to include them in the exceptions for checkpatch.
Remove the unused typedef's.
Change-Id: I18f039567edd5b24dbb41df5406c154f31022ae7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6178
Tested-by: jenkins
Reviewed-by: Christian Hoff <christian.hoff@advantest.com>
The existing code asserted in that case, which is not correct. This
would allow the user to crash OpenOCD with a bad ELF file, which is
not what we want. A proper error should be reported in that case and
OpenOCD should not crash.
Change-Id: Ied5a6a6fd4ee0fd163f3fe850d304a121ecbe33a
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/6172
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Libusb defines both the struct and a typedef to the struct using
the same struct name. It's then possible to use either 'struct x'
and 'x'. E.g.:
typedef struct libusb_device libusb_device;
OpenOCD is not consistent and uses a mix of 'struct x' and 'x'.
To make OpenOCD code uniform, stick at project's coding style and
use 'struct x' in place of the typedef'd name.
Change-Id: I901458b680e42830d3f371e47997157f91b7f675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6165
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit a7d68878e4 ("helper/command: unregister commands through
their full-name") introduces for the first time in OpenOCD the use
of jimtcl API Jim_DeleteCommand().
The prototype of Jim_DeleteCommand() has changed with jimtcl 0.80
and the current code doesn't build with jimtcl 0.79 or older. This
is an issue for those distributions, like Debian, that provide
jimtcl as a separate package/library and have not switched yet to
the new jimtcl version.
Add a compile-time condition to cope with the jimtcl API change.
Change-Id: Ic813ab7c0ebd3c8772f27775ba3912a47d5c275c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: a7d68878e4 ("helper/command: unregister commands through their full-name")
Reviewed-on: http://openocd.zylin.com/6191
Tested-by: jenkins
Uses CMSIS-DAP v 1.2 or higher protocol command DAP_SWD_Sequence
to write to DP TARGETSEL register. This write is not acknowledged
by device so we cannot use standard DAP_Transfer
Change-Id: Ib252d09570bcc2282be5f854e0ab9a0dfda06189
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6117
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
Commit 246782229f ("smp: replace commands smp_on/smp_off with
"smp [on|off]"") deprecates some multi-word comments, when openocd
was unable to properly handle mixes of multi-word commands and tcl
procedures having a common initial word.
This limitation is over, so move in startup.tcl the multi-word
commands deprecation, making it easy to remove them after a grace
period.
Change-Id: Icb550d1fa7559b95692d2a1244880da6c90ec0b2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5677
Tested-by: jenkins
Windows socket descriptor is not file descriptor, so when
using remote_bitbang on Windows, it fails with "fdopen:
failed to open write stream".
This patch removes the file write stream, replaces it
with socket write calls.
Change-Id: Ifd7c8a4139a5ac51ecd2846835a7a947a90fe16c
Signed-off-by: Yun Liu <liuyun.97@gmail.com>
Reviewed-on: http://openocd.zylin.com/6096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some CMSIS-DAP adapters keep buffered packets over
USB close/open so we need to flush up to 64 old packets
to be sure all buffers are empty.
Flush just after cmsis_dap_open() and in the case of command mismatch.
Change-Id: If21a118639e64d90635b4ecf81013d29a7b9f78d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6135
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Check returned HID report number (or the first byte of returned
bulk packet) which should be equal to the issued command or 0xff
in case of the command is not implemented.
Fix error return paths in cmsis_dap_init() to clean up the adapter
connection.
Don't fail cmsis_dap_init() when an unimportant function fails
(for the case the adapter doesn't implement some parts of protocol).
Change-Id: Ief8382aabe9915346b2273702fb2ff17bbb5eb1b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6121
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
The function's name was consistent with its purpose to handle
commands that were not at root level, thus not directly 'known'
by jimtcl.
Rename it as jim_command_dispatch() to highlight that now it is
a jim_handler and its purpose is to dispatch the call to the
proper command handler.
Change-Id: I9491a6d6459b8eb37a6c402abcae08388c693764
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5791
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that all commands are executed through the common handler
command_unknown(), the message about command execution is logged
by command_unknown(). There is no need, for "native" commands
(.jim_handler) at root level to log the message (again) by itself.
Remove calls to script_debug() apart from command_unknown().
Make script_debug() static as only used in command.c.
Change-Id: I9b2728b69e7643d6121c4b35a96bc825bcb5488d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5676
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
There is no need anymore to keep alive the tree of struct command.
Remove it and let jim to free() the command's struct command that
is referenced through command's private data.
Change-Id: I2cd84e0274a969ce200320e3a177ac20c7823da0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5675
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While keeping the struct command in place, unregister the jim
commands by scanning the list of jim commands through their
full-name.
Change-Id: I0e903fbc31172858b703d67ccd471809c7949e86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5674
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that every command has struct command as private data, use jim
to get access to the struct command to read the command mode,
instead of running through the tree of struct command.
Change-Id: Iddacdbac604714f6abe38a050daad245bdcfd20c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5673
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that the commands are registered using their full-name, the
full-name is in argv[0].
Don't rebuild the full-name but use directly argv[0].
Change-Id: Ic9e469ac39276367b8c47527e70791ff470fefbc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5672
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While still keeping the tree of struct command, stop registering
commands in jim by the root "word" only.
Register the full-name of the command and pass as private data the
struct command of the command itself.
Still use the tree of struct command to un-register the commands.
Some "native" commands (.jim_handler) share the same handler, then
the handler checks the command name to run the right code.
Now argv[0] returns the full-name of the command, so check the
name by looking in the struct command passed as private data.
Change-Id: I5623c61cceee8a75f5d5a551ef3fbf5a303af6be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5671
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The current implementation of "help" related commands is tightly
connected to the tree of struct command.
The TCL commands 'add_usage_text' and 'add_help_text' have to add
fake commands in the tree of struct command to handle the help of
TCL procs.
Move all the help texts in a list accessible from the struct
command_context and register the commands through their full name.
Keep the list sorted alphabetically by the command name, so the
result of commands 'help' and 'usage' will be sorted too.
Remove the associated help and usage during commands un-register,
but call help_del_all_commands() for the text added through TCL
commands 'add_usage_text' and 'add_help_text'.
The resulting help and usage output is not changed by this patch
(tested on all the help and usage strings in current master
branch).
Change-Id: Ifd37bb5bd374cba1a22cd7aac208505b4ae1e6fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5670
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A tcl proc can be executed anytime, in any command mode.
Let the command "command mode" to detect a tcl proc and return the
string "any".
Change-Id: I0559076c3063632ee0ea9a57a25f91060209b77f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5669
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Replace the "struct command *parent" parameter with a string that
contains the command prefix.
This abstracts the openocd code from the knowledge of the tree of
struct command.
This also makes unused the function command_find_in_context(), so
remove it.
Change-Id: I598d60719cfdc1811ee6f6edfff8a116f82c7ed6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5668
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In current code the current target is overridden whenever
jim_handler_data is not NULL. This happens not only with target
prefixed commands, but also with cti, dap and swo/tpiu prefixed
commands.
While this is not causing any run-time issue, by now, the
behaviour is tricky and makes the code cryptic.
Add a specific field to struct command for the target override so
the content of jim_handler_data can be restricted to command
specific data only (today only cti, dap and swo/tpiu).
Extend the API register_commands() to specify the presence of
either the command data or the override target.
The new API makes obsolete calling command_set_handler_data() to
set jim_handler_data, so remove it.
Change-Id: Icc323faf754b0546a72208f90abd9e68ff2ef52f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5667
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that target override is uniformly implemented for all types of
commands, there is no need for target-prefixed "native" commands
(.jim_handler) to sneakily extract the overridden target from the
struct command.
Modify the commands to use the standard API get_current_target().
Change-Id: I732a09c3261e56524edd5217634fa409eb97a8c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5666
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Today openocd registers the commands to jim with three methods:
1) "native" commands (.jim_handler) at root level are registered
directly as jim commands;
2) "simple" commands (.handler) at root level are registered
through the handler script_command();
3) all other commands not at root level are registered through the
handler command_unknown().
Apart from using different handler, other inconsistencies are
present:
a) command in 1) are not checked for their "mode", so are run with
no check about current mode (COMMAND_CONFIG or COMMAND_EXEC);
b) target_call_timer_callbacks_now() is called only for "simple"
commands and not for "native" commands;
c) target override is performed only for "simple" commands and not
for "native" commands.
Drop script_command() and extend command_unknown() to uniformly
handle all the cases above, fixing all the inconsistencies already
mentioned.
The handler's name command_unknown() is probably not anymore
appropriate, but will be renamed in a separate change.
Note: today all the commands in a) have mode CONFIG_ANY, apart for
"mem2array" and "array2mem" that have mode COMMAND_EXEC. But the
latter commands are registered during target init, so do not exist
during COMMAND_CONFIG and no issue is present.
Change-Id: I67bd6e47eb2c575107251b9192c676c27d4aabae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5665
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While registering a new command, jim accepts a pointer to command's
private data that will be accessible during the command execution.
Today openocd is not consistent and passes different private data
depending on the command, and then even overwrites it:
- "simple" commands (.handler) are registered with their own
struct command pointer as command private data;
- "native" commands (.jim_handler) at root level are registered
with NULL command private data;
- "native" commands (.jim_handler) not at root level are
registered with the struct command pointer of their root command
as command private data but, when executed, the command private
data is overwritten by the value in field jim_handler_data taken
from their struct command.
Uniform the usage of command private data by always set it to the
struct command pointer while registering the new commands.
Note: for multi-word commands only the root command is registered,
so command private data will be set to the struct command of the
root command. This will change later in this series when the full-
name of the command will be registered.
Don't overwrite the command private data, but let the commands that
needs jim_handler_data to get it directly through struct command.
For sake of uniformity, let function command_set_handler_data() to
set the field jim_handler_data also for "group" commands, even if
such value will not be used.
Now Jim_CmdPrivData() always returns a struct command pointer, so
wrap it in the inline function jim_to_command() to gain compile
time check on the returned type.
While there, uniform the code to use the macro Jim_CmdPrivData()
to access the command's private data pointer.
Change-Id: Idba16242ba1f6769341b4030a49cdf35a5278695
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5664
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
If current core is in EL0, it cannot use 'msr sctlr_el1, x0'
Change-Id: I04e60e39e4c84f9d9de7cc87a8e438f5d2737dc3
Signed-off-by: Cheng-Shiun Tsai <cheng.shiun.tsai@gmail.com>
Reviewed-on: http://openocd.zylin.com/6051
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The target mem_ap is a convenient way to access buses, memory and
peripherals behind an ARM AP.
The current implementation provides only access through OpenOCD
commands, because GDB remote protocol has to interact with a CPU
and has to operate on CPU states and registers.
Using GDB to access the memory is welcome, because GDB can resolve
the symbol's address from an ELF file and can nicely display the
content of complex struct and data types.
Extend mem_ap target with the bare minimal support for a remote
GDB connection, by emulating a fake basic ARM core. It means that
only a GDB that has support for ARM can be used (either 'aarch64',
'arm' or 'multiarch' GDB). This is not seen as a big limitation,
because the mem_ap target is mainly used on ARM based devices.
Add a minimalist register description for the fake CPU.
Fill the field 'debug_reason' as expected by GDB server.
Call the target halted event to reply to GDB halt requests.
For backward compatibility, don't open the GDB port by default. If
needed, it has to be specified at 'target create' or 'configure'
with the flag '-gdb-port'.
Change-Id: I5a1b7adb749746516f5d4ffc6193c47b70132364
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6034
Tested-by: jenkins
There are some breakpoint/watchpoint related code in armv8_dpm.c,
but seems not working for aarch64. Target aarch64 has its own
breakpoint implementation in aarch64.c. This commit follows the
same logic to add watchpoint support for target aarch64.
This commit also increases the size of stop_reason[] in function
gdb_signal_reply() since the old size is too small to fit in a
64-bit address, such as ffff8000115e6980.
Change-Id: I907dc0e648130e36b434220f570c37d0e8eb5ce1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/4761
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Kevin Burke <kevinb@os.amperecomputing.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Each one of CMSIS-DAP command handlers was responsible for setting
HID report number, which in case of USB bulk transport was not used
at all. The command had to be filled with 1 byte offset whereas
the response was read without an offset.
Introduce 'command' and 'response' pointers into struct cmsis_dap.
Use them for filling the command and read the response respectively.
CMSIS-DAP command parameter are now at positions as documented in
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__Commands__gr.html
Adjust buffer allocation for HID and USB bulk transports.
While on it, use h_u32_to_le() and h_u16_to_le() instead of per-byte
writes.
Change-Id: Ib0808d6826ba0e254c1007ace8b743405536332a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6120
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The hidapi cmsis-dap backend is using a packet_size of
64+1: 64 is the bMaxPacketSize0 and 1 is the hid Report-Id.
In hidapi::hid_write(), the packet_size is decremented by 1 and
stored for the next transfer.
The packet_size is now valid bMaxPacketSize0=64,
so when hid_read() is called, libusb_bulk_transfer() finishes w/o timeout.
For the libusb bulk backend, the same packet_size of 64+1 is used,
but there's no hid_write() to decrement and store it for the next read.
So the next time a read is done, it will try to read 64+1 bytes.
Fix this by putting the packet logic within each backend.
Use calloc() to allocate the struct cmsis_dap to be on safer side.
Change-Id: I0c450adbc7674d5fcd8208dd23062d5cdd209efd
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5920
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Now that the old drivers have been converted to libusb1, there is
no need to keep the build dependency from libusb0.
Drop libusb0 from configure and makefiles, remove the libusb0
helper and remove libusb0 and libusb-compat from the README files.
Change-Id: Icc05be74ae5971ba6cbb67d39107c709a4d826e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5993
Tested-by: jenkins
Marc Schink
R. Diez
Tim Newsome
Adrian Negreanu
Jan Matyas
Antonio Borneo
Chengyu Zheng
micbis
Tarek BOCHKATI
Tomas Vanek
Yasushi SHOJI
Evgeniy Didin
Daniel Anselmi
Peter Lawrence
asier70
Luis de Arquer
Christian Hoff
Florian Meister
Yun Liu
Cheng-Shiun Tsai
Liming Sun