Init the ARMv7-M magic number. Define predicate verifying it.
Use it to resolve a lurking bug/FIXME: make sure the ARMv7-M
specific DAP ops reject non-ARMv7-M targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The semihosting interface has a strange convention for read/write where
the unused amount of buffer must be returned. We failed to return the
total buffer size when the local read() call returned 0.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
srst_asserted and power_restore can now be overriden to do
nothing. By default they will "reset init" the targets and
halt gdb.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When the TAR cache was explicitly invalidated, don't bother
printing it; the actual hardware status is more informative.
Provide some doxygen for the MEM-AP setup routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
If the MEM-AP cache is invalid, don't display it; just report that
invalidity as an error. (This bug has been observed with "mdw 0 32"
after just a "reset halt". Some code is being wrongly bypassed...)
If it's valid, display that cache at DEBUG level, not ERROR. Also,
don't assume it's an AHB-AP; it could be another flavor of MEM-AP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reject invalid AP numbers (256+) as Tcl operation parameters.
Shrink one of the overlong lines.
Add my copyright to the ADIv5 code (multiple contributions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make messages reference "DAP" if they're actually transport-agnostic, or
"JTAG-DP" when they're JTAG-specific. Saying SWJ-DP is often wrong (on
most Cortex-A8 chips) and is confusing even if correct (since we don't
yet support SWD).
Rename a JTAG-specific routine to jtagdp_transaction_endcheck() to highlight
that it's JTAG-specific, and that identify DAP clients undesirably depending
on JTAG. (They will all need to change for SWD support.)
Shrink a few overlong lines of code. Copy a comment from code removed
in a previous patch (for the ARMv7-M "dap baseaddr" command).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make the ARMv7-M DAP code reuse the command handler for "dap baseaddr".
For some reason, this DAP command wasn't converted earlier.
This is a code shrink and simplification; it also removes a needless
transport dependency on JTAG.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The term "DPM" is probably not well known ("Device Power Management"?),
so identify its source in the current ARM architecture specification.
It's relevant to ARMv6, ARMv7-A, and ARMv7-R ... but not "M" profiles.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cygwin would fail to reopen a previously written file if the mode is
not given.
Simplified converting the open flags and made sure the win32 O_BINARY
bit is set.
Added define for systems that do not support O_BINARY.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
SYS_FLEN would be called before a write on a descriptor to check its size.
Currently lseek would fail with -1 when given the stdout/stderr descriptor.
Changing to use fstat seems to be the standard way of handling this.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
ARMv7-M defines a "lockup" state that's entered in certain double
fault sequences which can't be recovered from without external help.
OpenOCD has previously ignored this.
Issue a diagnostic saying the chip has locked up, and force exit
from this state by halting the core. It's not clear this is the
best way to handle lockup; but there should now be less confusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add space missing after the invalid ACK value. On init, say
which AP is being used, and don't assume it's an AHP-AP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
If the target and openocd are idling, the log should normally
be silent at level 3. (Given no verbose logging options.)
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The breakpoint/watchpoint message was wrong for Feroceon and
Dragonite, which have only one working watchpoint unit.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This fixes a bug whereby GDB's breakpoints weren't activated.
The root cause is a confused interface to resume(). Fix by
almost ignoring the "handle breakpoints" parameter; it only
seems related to the case of skipping breakpoint-at-PC.
Update a few coments to clarify what's happening.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Doxygen: don't be needlessly verbose; alphabetically sort members
TODO: add random bits; clarify which manuals are referenced
ARM disassembler: mention a few opcodes that still aren't handled
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update the comments about DP registers and some of the bitfields.
Remove inappropriate (and unused) DP_ZERO declaration.
Add some (currently unused) #defines needed for SWD protocol support,
based on previous patches from Andreas Fritiofson and Simon Qian.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
If GDB halts unexpectedly, print reason: srst assert or power
out detected.
If polling fails, then things are a bit trickier. We do not
want to spam telnet or the log with polling failed messages.
Leave that case be w/a comment in a code for now.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Skip over a bkpt instruction if found on resume/step.
Only software breakpoints known to OpenOCD are currently handled.
So this handles the special case of either a user added bkpt
or library added, eg. semi-hosting support.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Don't just complain about an invalid ACK; say what the
value was, to help troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Until we manage breakpoints at runtime (patches not ready for 0.4)
the only way this code should touch them is to disable them at server
startup (a previous debug session may have left them active).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add doxygen and other comments for what's more or less the lowest
level JDAG-DP primitive, to access JTAG_DP_{A,D}PACC registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Teach most remaining ARM cores how to use the "reset-assert" event.
Same model as elsewhere: iff a handler is provided for that event,
use that instead of trying to assert SRST (which may be unavailable,
or inappropriate since it resets too much). Else no change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Shrink some overlong lines. Add my 2009 copyright.
Move a declaration to the beginning of its block.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates three aspects of debugger/exception interactions:
- Save the user's "vector_catch" setting, and restore it after reset.
Previously, it was obliterated (rather annoyingly) each time.
- Don't catch BusFault and HardFault exceptions unless the user says
to do so. Target firmware may need to handle them.
- Don't modify SHCSR to prevent escalating BusFault to HardFault.
Target firmware may expect to handle it as a HardFault.
Those simplifications fix several bugs. In one annoying case, OpenOCD
would cause the target to lock up on ome faults which triggered after
the debugger disconnected.
NOTE: a known remaining issue is that OpenOCD can still leave DEMCR
set after an otherwise-clean OpenOCD shutdown.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
DCC downloads should be enabled for any self repecting
openocd config file for arm7/9. Print out note about
it otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Allow targets to run checks post reset. Used to check
that e.g. DCC downloads have been enabled.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Use correct tcl syntax to throw exception.
the syntax is "return -code error" not "return -error"
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing.
Don't use "&function"; its name is its address.
Unrelated: fix typo in one "target.c" usage message.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Uupdate some helptext to be more accurate.
Don't use "&function"; functions are like arrays, their address
is their name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Fix the User's Guide to say where the magic CP15 bits are defined;
and add comments in case someone provides mcr/mrc methods.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Deprecate the "pass an instruction opcode" flavor of cp15
access in favor of the "arm mcr ..." and "arm mrc ..."
commands, which offer fewer ways to break things.
Use the same EBNF syntax in the code as for the user's guide.
Update User's Guide to say where to find those magic values
(which table in the ARM920 TRM).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Deprecate the "pass an instruction opcode" flavor of cp15 access
in favor of the "arm mcr ..." and "arm mrc ..." commands, which
offer fewer ways to break things.
Use the same EBNF syntax in the code as for the user's guide.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Uupdate some helptext to be more accurate.
Fix the User's Guide in a few places to be more consistent (mostly
to use brackets not parentheses) and to recognize that parameter may
be entirely optional (in which case the command just displays output,
and changes nothing). Also reference NXP, not Philips, for LPC chips.
Don't use "&function"; functions are like arrays, their address
is their name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Fix the User's Guide in a few places to be more consistent (mostly
to use brackets not parentheses) and to recognize that parameter may
be entirely optional (in which case the command just displays output,
and changes nothing). Also reference NXP, not Philips, for LPC chips.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines, remove some empties.
Add a couple comments about things that should change: those
extra TCK cycles for MEM-AP reads are in the wrong place (that
might explain some problems we've seen); the DAP command tables
should be shared, not copied.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide;
no angle brackets in either place.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines, remove some empties.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines; remove some empties.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide helptext which was sometimes missing; update some of it
to be more accurate (mostly they display something w/no args).
Usage syntax messages have the same EBNF as the User's Guide.
In some cases, *exactly* what the user's guide shows... e.g.
talking about "offset" not "address" for trace_image.
Don't use "&function"; functions are like arrays, their name
is their address.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell
Nicolas Pitre
Øyvind Harboe
Spencer Oliver
Edgar Grimberg