This adds a set of helper functions with the aim to make it possible
to flash mass-market devices without RTFMing altogether (i.e. to
obsolete GPL-violating proprietary tjtag and other similar software).
Real-life tested on an RT-N16 and WRT54GL.
Change-Id: I197a9b28a5f386803f081057c4b4ebf2f9c447b1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1850
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested flashing a real v1.1 device.
Change-Id: Ie0d202b9fded8b92e731d93e0ef17be415a75fc8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1852
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".
The RAM setup is not done as it would require considerable efforts
without much practical gain.
The only issue I noticed so far is that "reset" doesn't actually reset
the chip.
Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.
Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.
Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
To be consistent with gdb_port and telnet_port, allow tcl_port
to be run to display the configured port number, while still
not allowing the user to change it after configuration.
Change-Id: Ibe6aedb3bd447f2985e42dd8246358481a047dd6
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1857
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* openocd.berlios.de -> openocd.sourceforge.net
* Update link to AM/DM37x Technical Reference Manual (ver R)
* "ICEpick" is properly spelled "ICEPick" according to TI
Change-Id: Ie04458e82c97ef766ec03bd9b9f27edadf5d1cb2
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1856
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
grammar fixes and so on.
Change-Id: Iaeb603447ecd9f77f1d49ce77044431442f4f219
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1855
Reviewed-by: Bill Traynor <btraynor@gmail.com>
Tested-by: jenkins
Reviewed-by: Francois Lorrain <francois.lorrain@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is not in the Intel hex file format specification but
some hex files may include comments (i.e. Altera USB-Blaster II
firmware) starting with '#'.
This patch makes image_ihex_buffer_complete_inner to skip
comment lines.
Change-Id: Id1f57d84d75da45e592f1c72b2b8c29193bc14e3
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1842
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
S25FL256S device tested on mbest LPC4357 EVM, S25S128S untested but
from the same data sheet.
Change-Id: Idf58416aab08671fe29d22c3c34c2118b25a9d45
Signed-off-by: Steve Moorby <steve.moorby60@gmail.com>
Reviewed-on: http://openocd.zylin.com/1844
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Try to detect the flash parameters based on the MCU SDID register. The hope
is that this works for K and KL series MCUs but it has only been tested on
a K21. YMMV.
Change-Id: Idfe71383a449065267f393b09ee3c3b24ac6a803
Signed-off-by: Per Ekman <pekenator@gmail.com>
Reviewed-on: http://openocd.zylin.com/1823
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On all platforms, search for scripts in
$HOME/.openocd
${run_prefix}${pkgdatadir}/site
${run_prefix}${pkgdatadir}/scripts
On Windows, set run_prefix to the runtime path of the executable, minus
${bindir}. This is to enable the install dir to be moved anywhere, as long
as the structure of the install dir is kept intact. On all other platforms,
run_prefix is empty.
The script paths can now be adjusted on Windows builds the normal way; by
overriding pkgdatadir at build time. For example, to create a Windows
package layout of
bin/openocd.exe
scripts/interface/...
scripts/target/...
you can do
configure --prefix= --enable-... and then
make pkgdatadir= DESTDIR=/some/path clean all install
Also, remove the unused PKGLIBDIR define.
Change-Id: If2c8228fc80c598d763efad21c5f51695ff9b6cf
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1796
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The set command was missing the $ prefix on the SJC_TAPID variable
and so would fail if SJC_TAPID was set
Change-Id: Ib9af58f5188bd8a2bc3f888309f203d624476c27
Signed-off-by: Alex Murray <alex.murray@cohdawireless.com>
Reviewed-on: http://openocd.zylin.com/1811
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch remove the hardcoded libraries. Also a check for
libftdi1 installations was added. This check fix an issue
with gentoo and maybe other systems.
Change-Id: Ieff9ec4d66ee0f3e6b22261a10e4cab9f26b6b51
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1759
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on Nemuisan Tokusei's. Untested, but original config was reported
to work ok.
Change-Id: Ic991dce55bfca266880081fe2bbd9e6e263b0fc0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1803
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
all other at91 cfg files already has this fix.
It also fix "No flash at address 0x...." error when JTAG chain consist of
more than one at91sam7sx cores during attempt to flash other than first mcu
in chain.
Change-Id: I7785d9103d0fc494b6a823e2c73f850373ffe112
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1812
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32F42xxx & STM32F43xxx series boudary scan TAP-ID are differ from
STM32F405xx/07xx & STM32F415xx/17xx.
And Section number was also fixed for RM0090 rev5.
Tested on a STM32F427IIT6 and STM32F429ZIT6.
Change-Id: Ie9c54c55b97b9c396ace752d94ea2ad916cc8479
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1808
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
get_flash_bank_by_addr() iterates through all flash banks
trying to auto_probe() every bank, even if bank can belongs to
target other than requested, and this other target can be
in non-halted state, which leads to error message and
operation abort.
Same situation in gdb_new_connection() and gdb_memory_map():
get_flash_bank_by_num() tries to auto_probe() requested bank,
so first get bank by get_flash_bank_by_num_noprobe(), check
if it belongs to current connection's target and skip
get_flash_bank_by_num() (actually autoprobing) if not.
Change-Id: I48b3f93dddcd9283394f14ad2de3248397c75ab3
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1813
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add a command to specify the serial string and pass it to the find helper.
Actual matching was already supported for both serial and product but was
using hard coded string indices. Instead use the indices from the device
descriptor.
Change-Id: I17c7538e5ad301ef41eace1ee70a202adab23bb4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1816
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a Cortex-M1 controller targetting aviation appliances.
Contributed (and live-tested) by 8daemon.
Change-Id: I133d6122cf6492b51ddbdbd800c16ba121d51bf3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1818
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Working against openmoko gta02 target, including TRST and SRST (the
stupid samsung chip fully resets under trst, so it's actually of
little use here).
Change-Id: I831124659fc12efbccef536f07d15509c2112f92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1814
Tested-by: jenkins
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit 2493671e2d added a default flash
padded value to the wrong file, should have been stm32lx.c not stm32f1x.c.
Change-Id: Idab634a03ccb28609cc977a92ac2b138d1e8d859
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1833
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Check reg_list[i]->feature for NULL pointers before checking feature->name
in order to avoid NULL access.
Change-Id: If20401a6c5aa5e1e29f0fcf9bb95585b49658832
Signed-off-by: Luca BRUNO <lucab@debian.org>
Reviewed-on: http://openocd.zylin.com/1809
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Jens Bauer <jens@gpio.dk>
The current way of detecting the sector size of the internal
flash does not work for all Kinetis MCUs. Add support for the
K21 flash by detecting the specific model from the SDID register
and picking the correct sector size based on that.
Change-Id: I41f678353e45a44561af8a3398bdd4479dfeea4f
Signed-off-by: Per Ekman <pekenator@gmail.com>
Reviewed-on: http://openocd.zylin.com/1764
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The default_flash_read() function seems to work ok.
Change-Id: Ia34c4642405f669ff63310fa8c641098b771a401
Signed-off-by: Per Ekman <pekenator@gmail.com>
Reviewed-on: http://openocd.zylin.com/1763
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the flash is not ready (MDM_STAT_FREADY is 0) then
dap_syssec_kinetis_mdmap() would act as if the MDM_STAT_SYSSEC bit was
set and erase the flash. Wait until MDM_STAT_FREADY is set before
checking the MDM_STAT_SYSSEC bit.
Change-Id: I5c3352f625599016625ed9be8787033f49bfacea
Signed-off-by: Per Ekman <pekenator@gmail.com>
Reviewed-on: http://openocd.zylin.com/1762
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Attempt to use target_buffer_set_u32_array to convert to target endian
arrays rather reimplementing code.
This also removed cfi_fix_code_endian as its functionality is also
repeated.
Change-Id: I7c359dbe46ea791cd5f6fb18d8b0fb6895c599d3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1783
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When programming large FPGAs the generated SVF files might contain really
long SDR scans. They won't fit in the 1MiB jtag scan page at all, so in
this case the allocated page needs to be bigger. The current code was
silently corrupting memory.
One particular example was sent by Volter targetting XC3S4000. It has an
SDR 11316992 bits long, that is 1414624 bytes.
Change-Id: I39f18d7e0654f2dbdf37df58c837c9ec1fb2aa2a
Reported-by: "Voltner, Jiří" <j.voltner@era.aero>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1792
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add device ID 0x437, a dual-bank part with 512KB total. This one used
the Medium+/HD flash size register to read the flash size in Kb rather
than the 0/1 code in the Medium+ parts.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Change-Id: I870fe3bb1b473939b7211c3b2edb44b4b3643648
Reviewed-on: http://openocd.zylin.com/1790
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the TMS570 Cortex-R4 MCU from TI and their USB stick
development kit, TMDX570LS31USB. Tested attaching, reset/halt/run, and
reading and writing memory and registers.
Change-Id: I12d779cef0c2b834f9bcf722307f35677cc4bd8f
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1788
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some MB9Ax (especially few internal SRAM model) fails programming
because of wrong SRAM basic-address on running algorithm.
Default SRAM basic-address must be 0x20000000.
This patch is fixing default SRAM basic-address and ramcode offset.
Tested on a MB9BF618T and MB9AF112K.
Change-Id: Ibda9aceb4c317bcae0dcce9f6d0fd1c4b5d81952
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1793
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The trace command was opening a file named with the source frequency.
This change correctly passes the filename that is specified.
Change-Id: Ia2eb8eda0e1e0f4f44b05c3a0ce7bef3bda51446
Signed-off-by: Alan Bowman <alan.michael.bowman@gmail.com>
Reviewed-on: http://openocd.zylin.com/1800
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by grepping for pointer casts.
Change-Id: I42ef3ebcce9fc6391154888b48601ede8377c34e
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1771
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
if data size is bigger than transfer buffer, all portions are
transferred from/to the same target address - address advance
after successful transmission missed.
Change-Id: I79a6c388af197ac062d2807e397a2d7947400520
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1679
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Found by grepping for pointer casts.
Also rewrite to reduce scope and allocate the few bytes needed on stack
instead of on heap.
Change-Id: Ia2a369fb612e807b981ee60ebcfd9c09c2fbdf4c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1779
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by grepping for pointer casts.
Some additional cast can be removed if hexify/unhexify arguments are
changed to a more suitable type.
Change-Id: I13796b056f00976979bf0e754de3aa7648f7f321
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Using the right parameter type, there's no need to resort to casting.
Change-Id: I8aec852431ead26e24793fd6fac8781353963bf2
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1777
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Because of the cast, the const decoration on the parameter provided no
guarantee against modification since it was silently discarded.
Change-Id: Ib83ade955e1a61ee2175c690620437b5e19cbb6a
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1776
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by grepping for pointer casts.
Change-Id: Ie2d698310b077c3849266e81df8e6a808cbc6896
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1775
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser
Robert P. J. Day
Franck Jullien
Steve Moorby
Per Ekman
Mathias K
Andreas Fritiofson
Alex Murray
Ed Maste
Sergey A. Borshch
Nemui Trinomius
Sergio Chico
Andrey Yurovsky
Spencer Oliver
Luca BRUNO
Dongxue Zhang
Alan Bowman