Found by clang.
Change-Id: Iaa952b063779f4d392d8bdc62a3e7ce9daef2740
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1498
Tested-by: jenkins
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Uppercase device/family names and change them to be more specific and
consistent across all STM32 families.
High-density STM32F10x has a Rev Y according to RM0008 Rev 14, so add
it.
I have a STM32F30x Rev Y, sitting on my desk, but it isn't described in
the reference manual. Add it as well.
Split the STM32L1xx Medium+ Density devices based on ID, to match the
reference manual. If I read it correctly, the Medium+ devices have
different revision mappings depending on their package/device ID. I have
no real devices to examine, however.
Change-Id: I5b95e5fa3cdeba219aa96838ea06ec1bb62bd921
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1497
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Factor out common bit masking and printing code and use intermediate
strings to avoid buffer size handling.
Change-Id: I7d8c12df11ade6cdca8c917b5524372daa498bf4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1496
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These chips are capable of reading the flash registers while they're
running.
Change-Id: I76b90b2bae1aa79b5a063b2073faa5d3ed93cfd7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1495
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The device was correctly used in stm32lx_probe but missing from stm32lx_get_info.
Change-Id: If288b8df3210a945e727e4e27cfbdb948db32fc7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1491
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
gcc (Gentoo Hardened 4.6.3 p1.13) produces a warning about the variable
assigned but not used. write() can sometimes write less than the specified
count so it's marked with warn_unused_result in the system headers and its
return value can't be ignored. The most correct solution would be to have a
loop writing the buffer until all bytes are written or an error is
returned but here it's impractical.
Change-Id: I75f7482e2b26fe0e6d70d34947518d3a8f0afe5c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1490
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Double const is bogus and breaks the build on Clang 3.3.
Change-Id: I9f9394d17f66289ac74ae6dd48f3165483b72e9e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1489
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
This fixes the build with Clang 3.3.
Change-Id: I729b4791c16178cdd4a87f7e1c04019da2c84b26
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1488
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes a bunch of errors like this:
aice_usb.c: In function 'aice_pack_htdc':
aice_usb.c:63:4: error: cast increases required alignment of target type [-Werror=cast-align]
Compile-tested only.
I think this can be seen as another justification for an ARM Jenkins
build target.
Also, the aice code I've seen so far seems to be assuming it runs on a
little-endian machine so probably there're some endianness issues
hiding. Hsiangkai, please get an old PowerPC Mac (or at least some
fast usb-equipped MIPS SOHO WiFi AP/router for which you can
cross-compile OpenOCD with OpenWrt) and do some real-life testing for
your code on Big-Endian. I propose it to be a requirement for any
non-trivial code submitted by a commercial entity of reasonable size.
Change-Id: I45e05257687d0020d7172b26a8666ebc1950e00c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1477
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When cross-compiling, current configure script fully ignores libftdi
unavailability and proceeds with LIBS having -lftdi -lusb, that
results in a non-obvious failure much later.
Try to verify libftdi is available by checking if ftdi_new function is
linkable.
Change-Id: I4f593d8ada1f38f82e7f1baa1a4b37b09619e1b4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1473
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It pointed to the Flyswatter 1 page.
Change-Id: Ib7e82669a31cad2bf8f6ba4a60b25ef9920b2584
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1478
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The currently used image is 404 so use an inline image instead.
Change-Id: I56a0d187fd06dc2c5c370e6532d89815ccec63d6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1451
Tested-by: jenkins
On XScale architecture, to write debug control register DCSR
and activate JTAG debug (ie. to choose Halt Mode), the
enabling can only be done while the board is held in reset
state (ie. PXAxx #RST line held low).
The current implementation writes to the register before
asserting the SRST line. Swap the order to activate the SRST
line before writing to DCSR.
Change-Id: I914b9d53d39bdeb5fe4ee5e11068cafafe0da4d2
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1458
Tested-by: jenkins
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Replace hexadecimal masks for vector catching with words
representing the caught exception, such as dabt for data
abort, etc ...
This way, the new xscale command is :
- xscale vector_catch
Reads back to the user the current vector catching status
- xscale vector_catch reset dabt pabt
Sets the caught vectors to data abort and prefetch abort
for example.
This is mostly taken from Cortex-M3 openocd code.
Change-Id: I66591d5796f0e07f0f31edc8d28722e1e48aa8c5
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1456
Tested-by: jenkins
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Only the support for at91sam3s8b is tested on real hardware.
Change-Id: I4ce23bc2f6131d9cf3ff1b301ab9e470d20845ab
Signed-off-by: Ulf Wetzker <ulf.wetzker@eas.iis.fraunhofer.de>
Reviewed-on: http://openocd.zylin.com/1424
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update is untested due to missing hardware.
Change-Id: Ibe286b741ebbb1c8ae0bd3dea4b8f3e12320ab34
Signed-off-by: Ulf Wetzker <ulf.wetzker@eas.iis.fraunhofer.de>
Reviewed-on: http://openocd.zylin.com/1423
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to the "AT91SAM ARM-based Flash MCU SAM3S Series datasheet"
(http://www.atmel.com/Images/doc11090s.pdf) p. 30 the lock region
size for the at91sam3sd9 family is 32 kbyte.
This fix is only based on the datasheet due to missing hardware.
Change-Id: Ic47b0642e4f11a60de477eaa0167038103b8ff15
Signed-off-by: Ulf Wetzker <ulf.wetzker@eas.iis.fraunhofer.de>
Reviewed-on: http://openocd.zylin.com/1422
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add Thumb-2 code to write flash memories that don't support DQ5 polling
* Make sure default values for unlock commands are set even if there is no PRI information given by the flash
* Add a fixup to disable DQ5 polling for the SST 39VF3201C
Change-Id: Ib08cf20547d0f500d5f78241521e6b49050c3d40
Signed-off-by: IS2T development team <dev.is2t@gmail.com>
Reviewed-on: http://openocd.zylin.com/1449
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This prevents segmentation fault that can occur on cortex_a targets if
gdb connection is established before it's halted and CPSR examined.
Change-Id: Id996200e0fd95440496509c1fecaabbdbf425e23
Tested-by: Henrik Nordstrom <hno@squid-cache.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
if gdb server (openocd) answers qfThreadInfo with an empty string during boot,
gdb will not request thread info anymore. to keep thread awareness in gdb,
we have to answer with a non empty string, 'l' indicates an end of list,
and is a valid answer here.
Change-Id: I7870a5db1090c786f306db16a25871e69b8a9760
Signed-off-by: Zied Guermazi <guermazi.zied@gmail.com>
Reviewed-on: http://openocd.zylin.com/1432
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
soft_reset_halt was only really intended for the older arm arch, eg. armv4/5.
Newer arch such as armv7m/mips do not need this as they have better alternatives.
Change-Id: Ifb360680b7e4bfa5365f3c79d82574bded952b45
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1442
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add pin controls (pin6 and pin8). These pins can be
controled either :
- with a fixed value (0 or 1)
- by TRST or SRST reset signal (driven low when signal
activated).
Change-Id: Ie6a3e57fc6ba6a38fdb9a009c976e3febab8f578
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1448
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Fixes are:
- Discard any stale data from the previous connection.
- Disable CR/LF translation on the (virtual USB) serial port.
- Increase the average USB packet size. The 1 KiB buffer was underutilised.
- Option "buspirate_speed fast" now works out of the box.
- Some extra comments, error checking, etc.
Change-Id: I72c49d943a8ce9c5e5d1644ef90cb1482f93c618
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/1437
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fixes regression introduced in 9785f51f that caused write outside
allocated memory during probe of devices with <1024K flash.
Reported-by: Alexander Pakhomov <ker0sin@yandex.ru>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: Ifba8833e436064624efbf678162538fd351a5702
Reviewed-on: http://openocd.zylin.com/1450
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
mips_m4k_bulk_write_memory was only called from target_write_buffer as an
optimization when the word count was large enough.
Remove mips_m4k_bulk_write_memory from the target type, causing the default
implementation to call the regular mips_m4k_write_memory instead.
Perform the dispatch to bulk write in mips_m4k_write_memory, enabling the
optimization for target_write_memory() writes with size 4, in addition to
target_write_buffer() writes.
It also enables making the choice of bulk write vs regular write
specifically for the architecture and not relying on the generic target
code to make a sensible decision.
Change-Id: I295f21a67ceaa195802403f2518ea2e0a025c1c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1215
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
This will enable the user to use either name when calling flash driver cmds.
For example the stm32f3x family use the same flash driver as the stm32f1x, so
the user has to use 'stm32f1x mass_erase 0' which can be confusing.
Now the user can also use 'stm32f3x mass_erase 0' with the same result.
Change-Id: I14280674c8dfa2ce1c01e327af7f38e36150462c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1428
Tested-by: jenkins
If mem_ap_sel_write_atomic_u32 fails then tmp_buff may not be released.
Detected by clang.
Change-Id: I3d5416bd47d0eea61f61ec02ac5e43c82f114108
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1433
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Ignore version of Boundary Scan TAP in newer revisions of the str9.
Change-Id: I6e205f8c731f07078c469e686025857c180f3a6d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1436
Tested-by: jenkins
Change scope of the variable gdb_reg_list_idx from global to module.
Change-Id: Ib8273c0769c11c1d5a338e4711efbddb8e8a0243
Signed-off-by: Jim Norris <u17263@att.net>
Reviewed-on: http://openocd.zylin.com/1441
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This makes libusb handling more consistent: if any driver requires
libusb, first check for libusb-1 availability, if not found and
libusb0 is ok for this case, try libusb0.
A user-visible bug fixed by this is that when a user was selecting a
driver that required libusb-1 but was lacking the necessary dev files
or libraries, configure didn't complain (but the build was failing of
course).
--enable-stlink doesn't really require libusb-1 but since it's using the
same automake symbol HLAADAPTER, ti_icdi is getting built too which needs
libusb1 unconditionally. Since using libusb-0.1 makes little sense anyway,
leave that as is.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I630a4ad9e4583743d45b2233bf5d8f4e5c0aab82
Reviewed-on: http://openocd.zylin.com/1434
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Print a user-friendly message when libusb_open() fails, e.g.
Error: libusb_open() failed with LIBUSB_ERROR_ACCESS
when there's a permissions problem.
Also output a configure warning if libusb older than 1.0.9 is detected.
Change-Id: I800f71f06672fe06c0a98a4e469f853b5021bcfe
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1430
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a config file for TIAO USB Multi-Protocol Adapter.
Based on schematics from http://www.mediafire.com/?zv158nnx1gv0cy2
Cc: Volkan K <volkan-k@users.sourceforge.net>
Change-Id: I0dfd93b0b1e558e4ccd7c94c005c099947ec94df
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
962b3eb40c included the old GPL address.
Change-Id: I7affbdc3fc1c9251ea90796ab9eeef4d56ba4308
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1440
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds support for JTAG programming by bitbanging GPIOs exposed on
the RaspberryPi's expansion header.
Tested by connecting directly to an STM32VLDiscovery board, without any
additional circuity. I observed maximum about 4MHz on the TCK pin with an
old analogue 'scope and about 100kHz when setting the speed to 100kHz.
Busyloop waiting is needed because even with a single 0ns nanosleep call
(with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low
to be useful.
The speed testing with adapter_khz 2000 gave the following results:
sudo chrt -f 1 nice -n -19 ./src/openocd \
-f interface/raspberrypi-native.cfg \
-c "set WORKAREASIZE 0x2000" \
-f target/stm32f1x.cfg -c "adapter_khz 2000"
wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s)
dumped 131072 bytes in 1.445699s (88.538 KiB/s)
This is 3.7 times faster for writing and 14.3 times faster for reading
compared to the generic sysfsgpio driver; probably the writing speed is
limited by the target itself here and reading speed might be considerably
higher too with appropriate connection and a capable target.
BCM2835 name is choosen over BCM2708 because the published peripherals
datasheet uses the particular model name and not family name.
Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/758
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updated OpenJTAG driver from www.openjtag.org to work with latest version of OpenOCD.
Change-Id: I2917f4e5835fb9ca5265e81dc38515fa97ae9503
Signed-off-by: Ryan Corbin <corbin.ryan@gmail.com>
Reviewed-on: http://openocd.zylin.com/1406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add target code for Andes targets.
Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andes AICE uses USB to transfer packets between OpenOCD and AICE.
It uses high-level USB commands to control targets instead of using
JTAG signals. I define an interface as aice_port_api_s. It contains
all basic operations needed by target-dependent code.
Change-Id: I117bc4f938fab2732e44c509ea68b30172d6fdb9
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1256
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Fritiofson
Spencer Oliver
Paul Fertser
Laszlo Papp
John Szakmeister
Robert Jarzmik
Ulf Wetzker
IS2T
Zied Guermazi
Evan Hunter
Antonio Borneo
R. Diez
Brent Roman
Giuseppe Barba
Jim Norris
Ryan Corbin
Hsiangkai Wang