Add the 'nand verify' command to perform a dump and fake-write
simultaneously, checking the read bits against those generated by the
write process. Appropriate user documentation for this command has
been added to the user guide as well.
The algorithm presently makes a relatively naive comparison. Some chips
that use ECC may not verify correctly using this implementation, but the
new documentation provides details about this limitation.
In some cases, the FILEIO_NONE access mode may be useful as a parameter
to indicate that file access should be disabled. High-level routines can
use it to skip file access calls, as 'fileio_open' will fail presently
if called to open a file using this mode.
This patch eliminates duplicated code in the the NAND 'dump' and 'write'
by using the new static helper functions.
These changes also fix a possible memory leak in nand dump command, in
the case that the dump file failed to open.
Overall, the changes should be functionally equivalent, but the
resulting code will be easier to improve and extend further.
This patch provides helpers APIs that will eliminate duplicated code in
the the NAND 'dump' and 'write' commands by factoring their common code
into static helper functions. These helpers may be useful for creating
new commands, as shown in the final patch to 'verify' flash from a file.
Several previously unreported error conditions now generate messages and
propogate the return codes, such as when the file fails to open and bad
arguments are given. These changes will fix a possible memory leak in
nand dump command, in the case that the dump file failed to open.
Overall, the changes should be functionally equivalent, but the
resulting code will be easier to improve and extend consistently.
Rewrite buf_cmp to use memcpy for bulk of comparison. Add static
helper to perform comparison of trailing byte, which uses another
static helper to perform a maksed comparison. The masked comparison
helper is used by the buf_cmp_mask to simplify its loop.
Improve types to use void *, unsigned, and return bool.
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Lots of files still include it, often through needless
duplicate inclusion of "log.h"; sigh.
This cleans up the inclusion graph a bunch, so there are
fewer inclusion paths, but it doesn't change much otherwise.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
downloadable algorithms actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also: "algorithm.h" doesn't need to include "types.h" again;
it already comes from a different header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Now the ARM11 cores can use the renamed arm_checksum_memory()
and arm_blank_check_memory() routines ... do so.
Sanity checked with "flash erase_check" of both NOR banks on an
OMAP2420 ... the algorithm code dumped four lines of of "poll"
status after each of almost 520 blocks (yes, *very* annoying) but
gave plausible results after producing that spam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Three changes: remove ARM11_HANDLER() in favor of normal structure
initialization syntax; fix goofy indentation in that structure; and
don't needlessly export arm11_register_commands(), it's only called
through that method table.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The arm7_9_checksum_memory() and arm7_9_blank_check_memory()
routines are not actually specific to the ARM7 and ARM9 core
generations ... they can work for any core which can run
algorithms using basic ARM (not Thumb) instructions.
Rename them; move the declarations to a more generic site;
likewise move the code (and tidy it a bit in the process).
NOTE: the blank_check() method falsely returned a success
status (0) on one error path, when the algorithm failed.
Fixed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously this flag was stored in "target_type", so that for example
if there were two ARM7TDMI targets in a scan chain, both would claim
to have been examined although only the first one actually had its
examine() method called.
Move this state to where it should have been in the first place, and
hide a method that didn't need exposure ... the flag is write-once.
Provide some doxygen. The examine() method is confusing, since it
isn't separating one-time setup from the after-each-reset stuff. And
the ARM7/ARM9 version is, somewhat undesirably, not leaving the debug
state alone after reset ... probably more of an issue for trace setup
than for watchpoints and breakpoints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Removes unused arm_jtag_buf_* helpers from arm_jtag.[ch]. These could
reappear if patches are provided to conver the tree to use them, but
this code should not be in the master tree until that series is ready.
Purge an unused routine from the tree and remove a layering violation.
If this code is needed, it should reappear somwhere in src/jtag/,
where struct scan_field gets defined.
It's completely unused; the obnoxious "DANGER!!!" comments
don't even explain what it was doing (shorthand SVN magic).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This fixes an issue due to the new command handler syntax caused by the mw handler playing with the args pointer before
using the CMD_NAME macro. Fix is to move this call above the lines changing args.
Create src/openocd.h to hold declarations previously made internally
by src/main.c and src/server/server.c. This ensures all functions
are verified to be in-sync at compile time (rather than at link),
making it easier to track down bugs.
Changed some printf format strings..
[dbrownell@users.sourceforge.net: shrink lines, fix indents]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Kick in ETM (and ETB) support for ARM11. Tested on OMAP 2420,
so update that configuration. (That's an ARM1136ejs, ETB,
OpenGL ES1.1, C55x DSP, etc.)
Also update the other ARM11 ETM + ETB targets in the tree
to set up these modules. (Not tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
These aren't desirable, given "standard" ETM support.
Also remove the now-unused arm11_find_target().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No point in having two identical examine methods for the
ARM7TDMI and ARM9TDMI drivers; move, rename, shrink, share.
Add a bit of doxygen; stop needlessly exporting a method.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Return NULL from etm_build_reg_cache() not ERROR_OK; and share
code on that fault path.
Let ETM code handle any tracking of its cache -- not callers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This will enable reusing many common ARM utilities, in
particular the ETM and ETB support. The ARM11 support
can still be much simplified after this patch, though.
Note: none of those common utilities kick in yet...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We have too many different registers, and too many version and
context dependent interpretations, for this type of bitfield
management to be scalable.
(Anyone who really wants bitfield interpretation *can* do that
in Tcl code...)
There are ... quite a few copies of the same ARM dummy registers.
There should eventually be one copy; this many is craziness.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Various cores with an ETB have its TAP misnamed ... either as a
boundary scan TAP or as the iMX "Secure JTAG Controller" (which
is, among other things, a JRC that could be used to shorten
scan chains).
Use the correct name for these TAPs, which we can recognize since
their IDs were assigned by ARM and these chips all document the
presence of an ETB. The 0x2b900f0f is ETB11; the 0x1b900f0f
is an older module, just called "ETB".
Also shrink the ETB's IR configuration; the default IR-Capture
value is fine, and the mask can specify that all four bits are
safe to check (per ARM documentation).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove the last external user of arm7_9_get_arch_pointers(), and
that annoying downcast utility. Add an is_arm7_9() predicate.
Stop returning specious success codes on various failure paths
in the ARM7/ARM9 commands which used that downcast utility.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Zachary T Welch
David Brownell
Krzysztof Dziuba
Dean Glazeski
Ferdinand Postema