Add support for the TI K3 family AM273 SoC.
For further details, see https://www.ti.com/lit/pdf/spruiu0
Change-Id: Ifa21d0760831f4f525ecd976fb8d086ffdbc9e9f
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7950
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Add support for the TI K3 family AM263 SoC.
For further details, see https://www.ti.com/lit/pdf/spruim2
Change-Id: I9a91b3d675511661dfc2710a7183bd59b98da133
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7948
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the TI K3 family AM243 SoC. This SoC is built on the
same base of AM642, so reuse the configuration with the exception of
Cortex-A53 which is not available on this device.
For further details, see https://www.ti.com/lit/pdf/spruim2
Change-Id: I971ba878b0f503e5120f6853634776eb61d05080
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7946
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Sort the documentation for the TI K3 parts alphabetically.
Change-Id: I2c40714ad590e3d9232a6f915c157d677e0c3610
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7945
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The AM2x family of K3 SoCs typically do not contain a Cortex-A53 or
A72 processor. So, make the cpu "up" functions available when armv8
processor count > 0.
Change-Id: I985b194fe7cc63e4134ad84ccd921cc456eb412f
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7944
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Convert the memory access ap port num as a variable to allow support
for the AM2x family of K3 SoCs.
Change-Id: Ibd96c94055721f60d95179dab21d014c15b0f562
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7943
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Convert the Cortex-R5 ap port num as a variable to allow support for
the AM2x family of K3 SoCs.
Change-Id: I7dc8b459dca8b5f21395230b5cb782b14538bd48
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7942
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Convert the sysctrl ap port num as a variable to allow support for the
AM2x family of K3 SoCs.
Change-Id: I1b5b55e48240e6654779dd636fdf07bca055e192
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7941
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This allows programmatically determining the debug reason.
Change-Id: I0c3e85cebb6dc28fc0fc212beca84a484ac654a5
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7952
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Fixes below Sparse tool warning.
warning: symbol 'breakpoint_watchpoint_remove_all' was not declared.
Should it be static?
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I4af1d5aa54abcb45f746b877513ba0b5fccbeb47
Reviewed-on: https://review.openocd.org/c/openocd/+/7955
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Enhance `mips32_read_config_regs` to better detect MIPS32 ISA,
DSP, and FPU features, allowing user to get more detailed
target information.
Most of these information will be used in MIPS m/iAptiv support.
Change-Id: I23571a626ec64fa019acac91bdbfcb434373bfc1
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7911
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This patch forces a read of register from the target
in the get_reg command in case the register cache
does not hold a valid value at that moment.
Note that the command "reg" already handles it
correctly, no fix is needed there.
Change-Id: I75fad25188e94ee4e06162ab6d600ea24dbf590a
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7958
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The original documents from Jedec since JEP106BG, do not report
the entry for "21 NXP (Philips)", replaced by "c".
It's clearly a typo.
Keep the line from JEP106BF.01 for "NXP (Philips)".
Change-Id: I273c8c5ecf48336ce5189b484a7236273ba90184
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7954
Tested-by: jenkins
In jtag_libusb_open I've added a parameter for delivering the device
description for which this function should search and adjusted all
callers of this function. A new driver for WCH CH347 JTAG chips
will use this new parameter.
See also: https://review.openocd.org/c/openocd/+/7937
Change-Id: I85e1d7b1f7912ba5e223f0f26323ff3b7600e17d
Signed-off-by: EasyDevKits <info@easydevkits.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The iManufacturer is also a member of structure libusb_device_descriptor.
No need to output a check message by checkpatch.sh
Change-Id: Ibbb2eb9cde3482c8d4d6ea784f51a973eb36f8c5
Signed-off-by: EasyDevKits <info@easydevkits.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7936
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add result check for mips32_pracc_read_regs in mips32_save_context.
Change-Id: Ie796d2b05a9feb11e246c2d0771b52cad4fb70db
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7932
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This makes it easier to look at log files where multiple gdb instances
are connected.
Change-Id: Ic5aca52b32ee03ac35ffbed9a2fc552abb0a1cba
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7895
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Previously, when listing the watchpoints, OpenOCD printed
numbers 0, 1 and 2 representing READ, WRITE and ACCESS type
watchpoints.
This patch changes it to 'r', 'w' and 'a'. This increases the
clarity as what type the watchpoint actually is.
Change-Id: I9eac72dfd0bb2a9596a5b0c080a3f584556ed599
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7909
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This patch adds the "all" option to the rwp command.
It removes all watchpoints, much like rbp all removes
all breakpoints.
Change-Id: Id58dd103085e558f17afa4a287888cf085566ca9
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7907
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously, if you ran a tcl command in capture like so:
"capture { reg 0x1000 hw }"
Such command did overwrite the tcl result if LOG_LVL_INFO or
lower was logged during it.
This patch changes it by prepending the log to the tcl result instead.
As the tcl results should not be lost during capture.
Change-Id: I37381b45e15c931ba2844d65c9d38f6ed2f6e4fd
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7902
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
If wp/bp is missing at address rwp/rbp won't return zero code (on smp).
Now it fixed.
Fixes: 022e438292 ("target: Change policy of removing watchpoints/breakpoints.")
Change-Id: I3a3c245f7088fc23227b286d2191fc7f3edba702
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7910
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the ARM MCRR/MRRC instructions which require the use of
two registers to transfer a 64-bit co-processor registers. We are going
to use this in a subsequent patch in order to properly dump 64-bit page
table descriptors that exist on ARMv7A with VMSA extensions.
We make use of r0 and r1 to transfer 64-bit quantities to/from DCC.
Change-Id: Ic4975026c1ae4f2853795575ac7701d541248736
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Chalfant <michael.chalfant@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Firstly, create the TPIU nrf52.tpiu if using the nrf52 target. This is
standard, using AP 0 and TPIU base address 0xE0040000.
Secondly, add a pre_enable handler for this TPIU which configures the
TRACEMUX field of the TRACECONFIG register. This register is reset
every time the MCU resets, so the pre_enable handler creates a
reset-end handler to ensure the register remains set.
Change-Id: I408b20fc03dc2060c21bad0c21ed713eee55a113
Signed-off-by: Frank Plowman <post@frankplowman.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7901
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
While we can read and write from memory from the view of various
processors, all K3 debug systems have a AXI Access port that allows
us to directly access memory from debug interface. This port is
especially useful in the following scenarios:
1. Debug cache related behavior on processors as this provides a
direct bypass path.
2. Processor has crashed or inaccessible for some reason (low power
state etc.)
3. Scenarios prior to the processor getting active.
4. Debug MMU or address translation issues (example: TI's Region
Address Table {RAT} translation table used to physically map
SoC address space into R5/M4F processor address space)
The AXI-AP port is the same for all processors in TI's K3 family.
To prevent a circular-loop scenario for axi-ap accessing debug memory
with dmem (direct memory access debug), enable this only when dmem is
disabled.
Change-Id: Ie4ca9222f034ffc2fa669fb5124a5f8e37b65e3b
Reported-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7899
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The Texas Instruments' K3 devices are a mix of AMP and SMP systems.
The operating systems used on these processors can vary dramatically
as well. Introduce a RTOS array variable, which is keyed off the cpu
to identify which RTOS is used on that CPU. This can be "auto" or
"hwthread" in case of SMP debug etc.
For example:
AM625 with an general purpose M4F running Zephyr and 4 A53s running SMP
Linux could be invoked by:
openocd -c 'set V8_SMP_DEBUG 1' -c 'set RTOS(am625.cpu.gp_mcu) Zephyr' \
-c "set RTOS(am625.cpu.a53.0) hwthread" -f board/ti_am625evm.cfg
Change-Id: Ib5e59fa2583b3115e5799658afcdd0ee91935e82
Reported-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7898
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Describe the SMP Armv8 cores in SMP configuration with coreid
explicitly called out. This allows for gdb session to call the smp
behavior clearly.
Change-Id: Ie43be22db64737bbb66181f09d3c83567044f3ac
Signed-off-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7897
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When _v8_smp_targets is used with V8_SMP_DEBUG=1, describe the targets
as SMP targets. However, the variable expansion is not in the context of
a proc, and a typo in referring to global $_v8_smp_targets causes this
to fail. Just refer to $_v8_smp_targets directly.
Change-Id: Iffe5fd2703bed6a9c840284285e70b8a8ce84e17
Signed-off-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7896
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Currently, instruction cache is being invalidated in
arc_{un,}set_breakpoint() regardless of whether the breakpoint's type is
HW or SW. For SW breakpoints, this has no net effect as the caches are
flushed as a by-product of overwriting instructions in main memory and
is thus merely unnecessary; but for HW breakpoints this invalidation is
not preceded by a flush and might lead to loss of data. This patch
removes the invalidate() call altogether to correct this undesired
behavior for HW breakpoints.
With this patch applied, all supported HW breakpoint tests from the gdb
testsuite are now passing with the arc-openocd backend.
Change-Id: I3d252b97f01f1a1e2bf0eb8fb257bdab0c544bc2
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7767
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The comment above armv8_dpm_read_current_registers() doesn't match
the implementation, as the function reads all the registers from
ARMV8_PC and above.
The registers currently read are not relevant to answer to the
usual GDB initial request through the 'g' packet. Plus the lack of
differentiation per core state (AArch32 vs AArch64) causes the
read of not existing registers in AArch32 triggering errors, as
tentatively fixed by https://review.openocd.org/5517/
Fix the code to read the registers initially required by GDB.
Modify the comment to report the register list in AArch32 and in
AArch64.
Keep the extra checks inside the read loop, even if they are
mostly irrelevant; this could prevent errors if someone needs to
extend the number of registers to read.
The current implementation of the register's description in
OpenOCD does not allow to discriminate among AArch32 and AArch64
registers. Add a TODO comment to highlight it.
Change-Id: Icd47d93c19a9e1694a7b51bbc5ca7e21a578df41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7887
Tested-by: jenkins
The secure microcontroller Infineon SLx2 uses a custom Cortex-M33.
The register CPUID reports value 0x490FDB00.
Reference link to the product:
Link: https://www.infineon.com/cms/en/about-infineon/press/market-news/2022/INFCSS202211-034.html
Change-Id: I8911712c55bd50e24ed53cf49958352f470027a5
Signed-off-by: Ahmed Boughanmi <boughanmi.external@infineon.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7879
Reviewed-by: Karl Palsson <karlp@tweak.au>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds error reporting when unknown image type is specified.
Previously, OpenOCD replied with an empty string.
Change-Id: I16220b1f5deb3b966a21731f0adf7911a78e8959
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7883
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Previously, the bcm2835_peri_base value would be printed as a decimal
value despite having a "0x" prefix, implying it should be a hex value.
BCM2835 GPIO: peripheral_base = 0x1056964608
Now, the value is correctly converted to hexidecimal.
BCM2835 GPIO: peripheral_base = 0x3F000000
Change-Id: Id59185423917e6350f99ef68320e2102a3192291
Fixes: b41b368255 ("jtag/drivers/bcm2835gpio: extend peripheral_base to off_t")
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
and DP_SELECT_DPBANK.
Use the defined symbols instead of magic numbers.
Change-Id: I19c86b183e57e42b96f76eed180c0492cd67bee1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7539
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DP_SELECT_APSEL and DP_SELECT_APBANK is no more used in ADIv6.
Change-Id: I4176574d46c6dc8eb3fe3aef6daab6e33492c050
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7538
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
add refresh command for lattice devices
rename gowin reprogram to refresh
rename virtex2 program to refresh
Change-Id: I9da83a614b96da3e947ac4608b0a291b1d126914
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7839
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on cologne
chip gatemate devices.
Change-Id: Ifa1c4ca6e215d7f49bd21620898991af213812e9
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7838
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on intel devices using
a proxy bitstream.
Change-Id: Ib947b8c0dd61e2c6fa8beeb30074606131b1480f
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7837
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on xilinx devices
using a proxy bitstream.
Change-Id: I68000d71de25118ed8a8603e544cff1dc69bd9ba
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7836
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Nishanth Menon
Peter Collingbourne
Erhan Kurubas
Evgeniy Naydanov
Walter Ji
Marek Vrbka
Oliver Graute
Marc Schink
Antonio Borneo
Kirill Radkin
Tomas Vanek
EasyDevKits
Parshintsev Anatoly
Tim Newsome
Florian Fainelli
Frank Plowman
Dubravko Srsan
Artemiy Volkov
Ahmed Boughanmi
Vincent Fazio
Peter Mamonov
Daniel Anselmi