The CMSIS-DAP used by NXP's LS1012ARDB board only supports JTAG,
and not SWD. Calling cmsis_dap_cmd_DAP_SWD_Configure returns with an
error (and doesn't actually do anything in the debugger).
Wrap the call to cmsis_dap_cmd_DAP_SWD_Configure in a check for
swd_mode, to make sure initialisation doesn't fail needlessly.
Change-Id: Id7e568cb6e36886bd7c5b3699d198a77a51c28c9
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4294
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change-Id: Ieea1b0dec88818e9e8d5c8c5d54aa8959556d77b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4275
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The SWDIO buffer has to be enabled, by setting SWDIO_OE, for data on
SWDIO to reach the target. Explicitly do this before sending the
switch sequences for JTAG-to-SWD, etc.
This makes the code insensitive to the state of SWDIO_OE specified in
ftdi_layout_init. It used to work only on adapters with a non-inverted
SWDIO_OE inited to 1, or inverted SWDIO_OE inited to 0.
Change-Id: I4b9e520ac1c7ce2a437251a05fc036bc68de718e
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4270
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Similar to the Sheevaplug fix inf95f8b70fbd0f7e9c91a2d9006b1abb2dd07ebf2
the OpenRD device has its JTAG interface on the first channel of the
ft2232, which is 0 for the new driver but was 1 for the old one. Correct
the config file appropriately. Also the device description was missing
the trailing " B" and thus not picking up the device correctly. Finally
add an adapter_khz setting in the OpenRD board configuration file - set
to 2MHz to match the Sheeva variant.
Confirmed as working thanks to Phil Hands providing me access to his
hardware to test on.
See also Debian Bug#793214; https://bugs.debian.org/793214
Change-Id: Ifacf53124eaa330bbbdf36dfa79e3256bf2a5201
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4254
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The dhcsr_save variable was used to save the value of
cortex_m->dcb_dhcsr so it could be restored later. However, all writes
in between the save and the restore use mem_ap_write_atomic_u32, not
cortex_m_write_debug_halt_mask, which means cortex_m->dcb_dhcsr isn’t
changed anyway. Delete the unnecessary local.
Change-Id: I064a3134e21398e1ecfc9f1fa7efd7b020b52341
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4240
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In cortex_m_assert_reset, in two locations, DHCSR is written directly
using mem_ap_write_u32. This means that the cached version,
target_to_cm(target)->dcb_dhcsr, is not updated when these writes are
performed, so subsequent writes to DHCSR that use
cortex_m_write_debug_halt_mask will change those bits back to their old
values which, unless modified in that particular invocation, come from
the cache. This causes an actual, observable bug on an STM32F7 in which
running “reset run” immediately after “program” can in some cases result
in execution proceeding with C_MASKINTS set (it is cleared on line 1021
but is then set immediately afterward in cortex_m_clear_halt), causing
failure of the application. Replace these mem_ap_write_u32 calls with
cortex_m_write_debug_halt_mask calls to do the same jobs.
Change-Id: Id35ca7f6057c2df2ba9cd67c53a73b50816d0b71
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4239
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
GCC7 with -Wall warns about possible string truncation with
snprint()-type functions with "directive output may be truncated writing
1 byte into a region of size between 0 and 9
[-Werror=format-truncation=]" + "note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 12" (or similar). Fix this by
increasing sizes of buffers.
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Ib848f2a56dd658783534158947ae1be7c0e99d45
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4175
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
GCC7 with -Wextra warns about switch-case blocks which fallthrough with
"this statement may fall through [-Werror=implicit-fallthrough=]". This
can be fixed by adding "special" comments: "/* fallthrough */".
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Iba0be791dbdd86984489b2d9a0592bb59828da1e
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4174
Tested-by: jenkins
Add "arm semihosting_cmdline [argv0 argv1 ...]" for setting the
command line arguments for the debuggee.
[andreas.fritiofson@gmail.com]: Dynamic allocation, empty default
Change-Id: I831ddd161d602f251940e29608a154e9590fdee1
Signed-off-by: Christian Groessler <chris@groessler.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3106
Tested-by: jenkins
This config covers the 4x Cortex A53 CPUs. A custom connector
is required from J14 to standard ARM JTAG on v1 boards. However
v2 hardware should have a standard FTSH-105-01-L-DV connector.
Pinmuxing code to enable JTAG pins is included in l-loader-poplar
repository, so board is flashed with open source code, JTAG
is available at very early boot. Alternatively the following
pokes can be issued from U-Boot to enable JTAG (e.g. to debug
hisilicon SDK).
mw 0xf8a210ec 0x130;
mw 0xf8a210f0 0x130;
mw 0xf8a210f4 0x130;
mw 0xf8a210f8 0x130;
mw 0xf8a210fc 0x130;
mw 0xf8a21100 0x130;
Change-Id: I2b83dfcb3dc5461c1620f94dd99aa7b31fdda59b
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-on: http://openocd.zylin.com/4161
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Renaming of all nrf51 NOR flash code to nrf5, as to prepare the
code for being able to flash nrf51 and nrf52 chips.
The nrf51 command is retained for backwards compatability.
"nRF5" is also the name Nordic Semiconductor uses to describe
both the nrf51 and nrf52 chips.
Change-Id: I5f4e3f1ec780184b28ad44f735a746e68908c502
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4209
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This cleans up the list of supported nrf51 chips considerably.
Change-Id: Ic74685657bb72a8703c0a49df4c48c54604ec2a7
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4208
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Trying to read the L0 idcode at the L1 idcode address 0xE0042000 often
resulted in an uncatched error. Reading at the right L0 address 0x40015800
afterwards results in reading 0. So access to the device is denied..
Change-Id: I6de92cf99a5d5d46c72f9ba055613cbc5753a951
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3883
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
in some cases we need something to test if uart is actually
properly connected.
Change-Id: I5a16b053164b34bb30ae8370753be12887a85c51
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Finally we can use this driver by default!
Change-Id: I09d215d1bd1dc16873a7379637e6869af65ad8f1
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4193
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Make this error message more useful by providing the port number
that we tried to bind to.
Change-Id: Ieb18adf0725a6ae99c77ebfaadc49d64ed407bbe
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-on: http://openocd.zylin.com/4157
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
TDO and TMS: Safest values given it's an evaluation board
and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
high impedance (tri-stated).
Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for Blue Gecko and Mighty Gecko chips from
Silabs.
They have different EFM32_MSC_REGBASE and LOCK register offset.
Based on the original patch from Andreas Kemnade.
Change-Id: I166c14960ced7c880b68083badd1b31372fefabe
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-on: http://openocd.zylin.com/4034
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: chrysn <chrysn@fsfe.org>
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.
See also Debian Bug#837989; https://bugs.debian.org/837989
Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Use unsigned constant for left shift operation in order to avoid the
following error with GCC >= 6.0:
../src/flash/nor/stm32f2x.c: In function ‘stm32x_handle_unlock_command’:
../src/flash/nor/stm32f2x.c:1324:67: error: left shift of negative value [-Werror=shift-negative-value]
stm32x_info->option_bytes.optcr2_pcrop = OPTCR2_PCROP_RDP | (~1 << bank->num_sectors);
Change-Id: I0ac082bd0dbb8dc2f61ffff8fdf486ab7962d2e0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4207
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Anton Fosselius <anton.fosselius@gmail.com>
Reviewed-by: Esben Haabendal <esbenhaabendal@gmail.com>
If no serial number is specified, disable TCP/IP device discovery to
ensure that a user does not unintentionally operate on a remote device.
Change-Id: I6a7e913b8b679fae003825468cd86d2014849b29
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4214
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If multiple devices are attached, do not automatically use the first
device found. Otherwise, a user may unintentionally operate on the
wrong device.
Change-Id: I08c4110b82e911e9e3e744d41830ffc6c56c44bf
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4213
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use a human-readable error description rather than just the error name
in log messages.
Change-Id: Iab4ff7a7e4d9993983a07eab9f462820d4ee8190
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4212
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
libusb is now optional for libjaylink because support for TCP/IP
devices is always available.
Change-Id: I03f2566f8e1703276671ac0f353f72394d21f2f0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4204
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Update to latest Git version and bump required libjaylink package
version to 0.2.0.
This version introduces support for devices with TCP/IP interface (e.g.
SEGGER Flasher ARM) and an additional debug level for I/O messages.
Change-Id: I030236aa704a91d1bb1843dd30010865947747e0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4202
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This partially reverts commit 56d163ce79.
That change certainly caused more pain than gain.
Change-Id: Ifb126abd1e6b89d29db8bf6a7b8af5dfc815c163
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4159
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A common use case seen in the wild is echoing a string of commands to an
existing openocd instance via netcat. The sequence of ; separated
commands can easily run over the line limit of only 256 chars.
Increasing this dramatically reduces surprises, at the expense of a tiny
amount of extra ram usage.
Change-Id: I2389d99d316a96b5fa03f0894b43c412308e12c4
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4132
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
They're never used, so just drop them.
Change-Id: Ie137deed3e7258f9d6af7e0cb508e73df0f53ee0
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4131
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
IDs for STM32F722, F723, F413 and F423 added, handling of PCROP
for F722/723 and additional nWPRT bits for F413/423 implemented.
The additional protection bit positions for F413/423 conflict
with other options bits for the F7xx variants, additionally the
last two sectors share a common bit.
Protection for F413 and F767/777 now use protection blocks
rather sectors for dealing with protections bits.
Checking for halted state in 'lock' and 'unlock' removed: When
PCROP is activated in F723, halted state is not detected properly,
but lock/unlock sequence is required to disable PCROP.
Tested with STM32F723E-Disco, STM32F413ZH-Nucleo.
Change-Id: Ie6ddab47a9ae8461087d369b4f289b7f9d1e031c
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4045
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change ftdi SWD driver and CMSIS-DAP to use it instead of LOG_DEBUG().
Change-Id: I17ba3de2086c7159209db61fba3faf067dfc5023
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3805
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A footnote in RM0038r14.
Change-Id: Ic31894d846fbbe917a7290b2b7ff8fb582bb65da
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4198
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If a MCU has FlexNVM partitioned as EEPROM backup only
(no data flash), kinetis_probe_chip() detects zero fcfg2_maxaddr1
and adjusts flash banks count to 1, what is obviously wrong.
The change limits the test to devices without FlexNVM.
Computation of program flash/FlexNVM blocks is now more robust.
Missing case 0x07 is added to switch (fcfg1_depart)
Change-Id: I0bd6030a0fe1ab62aeb0223bbdf2aee1505bf6a0
Reported-by: simon.haines@scalardata.com
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4180
Tested-by: jenkins
Reviewed-by: Simon Haines <simon.haines@scalardata.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I2692b9877a7f877104528f279a69e8cc1cfbcdbf
Reported-by: David Miller Lowe <milhead@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4173
Tested-by: jenkins
Reviewed-by: Miller Lowe <miller.lowe@trailtech.net>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch improves the OSRunning check. If the rtos_running check
fails, update_threads will return an error rather than attempt to update
the thread list using bad values.
Change-Id: I8614c325504d3a9ab19aebb6862b1fe445a0c8e7
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4166
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch corrects a number of style infractions in RTOS support for
uC/OS-III. These were missed during initial review last year prior to
the 0.10.0 release.
Change-Id: Ia2139f6ca381d4087fd8ee989f7a03ac474d7440
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4120
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Bas Vermeulen
Robert Jordens
Marc Schink
Jonas Norling
Jonathan McDowell
Christopher Head
Freddie Chopin
Andreas Fritiofson
Tim Newsome
Peter Griffin
Slowcoder
Uwe Bonnes
Oleksij Rempel
Robert Foss
Diego Herranz
Andrea Merello
Fabio Utzig
Paul Fertser
Karl Palsson
Andreas Bolsch
Tomas Vanek
Steven Stallion