yosys/techlibs/greenpak4/cells_sim_digital.v

`timescale 1ns/1ps

/*
 This file contains simulation models for GreenPAK cells which are possible to fully model using synthesizeable
 behavioral Verilog constructs only.
 */

module GP_2LUT(input IN0, IN1, output OUT);
	parameter [3:0] INIT = 0;
	assign OUT = INIT[{IN1, IN0}];
endmodule

module GP_3LUT(input IN0, IN1, IN2, output OUT);
	parameter [7:0] INIT = 0;
	assign OUT = INIT[{IN2, IN1, IN0}];
endmodule

module GP_4LUT(input IN0, IN1, IN2, IN3, output OUT);
	parameter [15:0] INIT = 0;
	assign OUT = INIT[{IN3, IN2, IN1, IN0}];
endmodule

module GP_CLKBUF(input wire IN, output wire OUT);
	assign OUT = IN;
endmodule

module GP_DCMPREF(output reg[7:0]OUT);
	parameter[7:0] REF_VAL = 8'h00;
	initial OUT = REF_VAL;
endmodule

module GP_DCMPMUX(input[1:0] SEL, input[7:0] IN0, input[7:0] IN1, input[7:0] IN2, input[7:0] IN3, output reg[7:0] OUTA, output reg[7:0] OUTB);

	always @(*) begin
		case(SEL)
			2'd00: begin
				OUTA <= IN0;
				OUTB <= IN3;
			end

			2'd01: begin
				OUTA <= IN1;
				OUTB <= IN2;
			end

			2'd02: begin
				OUTA <= IN2;
				OUTB <= IN1;
			end

			2'd03: begin
				OUTA <= IN3;
				OUTB <= IN0;
			end

		endcase
	end
endmodule

module GP_DELAY(input IN, output reg OUT);

	parameter DELAY_STEPS = 1;
	parameter GLITCH_FILTER = 0;

	initial OUT = 0;

	generate

		if(GLITCH_FILTER) begin
			initial begin
				$display("ERROR: GP_DELAY glitch filter mode not implemented");
				$finish;
			end
		end

		//TODO: These delays are PTV dependent! For now, hard code 3v3 timing
		//Change simulation-mode delay depending on global Vdd range (how to specify this?)
		always @(*) begin
			case(DELAY_STEPS)
				1: #166 OUT = IN;
				2: #318 OUT = IN;
				2: #471 OUT = IN;
				3: #622 OUT = IN;
				default: begin
					$display("ERROR: GP_DELAY must have DELAY_STEPS in range [1,4]");
					$finish;
				end
			endcase
		end

	endgenerate

endmodule

module GP_DFF(input D, CLK, output reg Q);
	parameter [0:0] INIT = 1'bx;
	initial Q = INIT;
	always @(posedge CLK) begin
		Q <= D;
	end
endmodule

module GP_DFFI(input D, CLK, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	initial nQ = INIT;
	always @(posedge CLK) begin
		nQ <= ~D;
	end
endmodule

module GP_DFFR(input D, CLK, nRST, output reg Q);
	parameter [0:0] INIT = 1'bx;
	initial Q = INIT;
	always @(posedge CLK, negedge nRST) begin
		if (!nRST)
			Q <= 1'b0;
		else
			Q <= D;
	end
endmodule

module GP_DFFRI(input D, CLK, nRST, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	initial nQ = INIT;
	always @(posedge CLK, negedge nRST) begin
		if (!nRST)
			nQ <= 1'b1;
		else
			nQ <= ~D;
	end
endmodule

module GP_DFFS(input D, CLK, nSET, output reg Q);
	parameter [0:0] INIT = 1'bx;
	initial Q = INIT;
	always @(posedge CLK, negedge nSET) begin
		if (!nSET)
			Q <= 1'b1;
		else
			Q <= D;
	end
endmodule

module GP_DFFSI(input D, CLK, nSET, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	initial nQ = INIT;
	always @(posedge CLK, negedge nSET) begin
		if (!nSET)
			nQ <= 1'b0;
		else
			nQ <= ~D;
	end
endmodule

module GP_DFFSR(input D, CLK, nSR, output reg Q);
	parameter [0:0] INIT = 1'bx;
	parameter [0:0] SRMODE = 1'bx;
	initial Q = INIT;
	always @(posedge CLK, negedge nSR) begin
		if (!nSR)
			Q <= SRMODE;
		else
			Q <= D;
	end
endmodule

module GP_DFFSRI(input D, CLK, nSR, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	parameter [0:0] SRMODE = 1'bx;
	initial nQ = INIT;
	always @(posedge CLK, negedge nSR) begin
		if (!nSR)
			nQ <= ~SRMODE;
		else
			nQ <= ~D;
	end
endmodule

module GP_DLATCH(input D, input nCLK, output reg Q);
	parameter [0:0] INIT = 1'bx;
	initial Q = INIT;
	always @(*) begin
		if(!nCLK)
			Q <= D;
	end
endmodule

module GP_DLATCHI(input D, input nCLK, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	initial nQ = INIT;
	always @(*) begin
		if(!nCLK)
			nQ <= ~D;
	end
endmodule

module GP_DLATCHR(input D, input nCLK, input nRST, output reg Q);
	parameter [0:0] INIT = 1'bx;
	initial Q = INIT;
	always @(*) begin
		if(!nRST)
			Q <= 1'b0;
		else if(!nCLK)
			Q <= D;
	end
endmodule

module GP_DLATCHRI(input D, input nCLK, input nRST, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	initial nQ = INIT;
	always @(*) begin
		if(!nRST)
			nQ <= 1'b1;
		else if(!nCLK)
			nQ <= ~D;
	end
endmodule

module GP_DLATCHS(input D, input nCLK, input nSET, output reg Q);
	parameter [0:0] INIT = 1'bx;
	initial Q = INIT;
	always @(*) begin
		if(!nSET)
			Q <= 1'b1;
		else if(!nCLK)
			Q <= D;
	end
endmodule

module GP_DLATCHSI(input D, input nCLK, input nSET, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	initial nQ = INIT;
	always @(*) begin
		if(!nSET)
			nQ <= 1'b0;
		else if(!nCLK)
			nQ <= ~D;
	end
endmodule

module GP_DLATCHSR(input D, input nCLK, input nSR, output reg Q);
	parameter [0:0] INIT = 1'bx;
	parameter[0:0] SRMODE = 1'bx;
	initial Q = INIT;
	always @(*) begin
		if(!nSR)
			Q <= SRMODE;
		else if(!nCLK)
			Q <= D;
	end
endmodule

module GP_DLATCHSRI(input D, input nCLK, input nSR, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	parameter[0:0] SRMODE = 1'bx;
	initial nQ = INIT;
	always @(*) begin
		if(!nSR)
			nQ <= ~SRMODE;
		else if(!nCLK)
			nQ <= ~D;
	end
endmodule

module GP_IBUF(input IN, output OUT);
	assign OUT = IN;
endmodule

module GP_IOBUF(input IN, input OE, output OUT, inout IO);
	assign OUT = IO;
	assign IO = OE ? IN : 1'bz;
endmodule

module GP_INV(input IN, output OUT);
	assign OUT = ~IN;
endmodule

module GP_OBUF(input IN, output OUT);
	assign OUT = IN;
endmodule

module GP_OBUFT(input IN, input OE, output OUT);
	assign OUT = OE ? IN : 1'bz;
endmodule

module GP_PGEN(input wire nRST, input wire CLK, output reg OUT);
	initial OUT = 0;
	parameter PATTERN_DATA = 16'h0;
	parameter PATTERN_LEN = 5'd16;

	reg[3:0] count = 0;
	always @(posedge CLK) begin
		if(!nRST)
			OUT <= PATTERN_DATA[0];

		else begin
			count <= count + 1;
			OUT <= PATTERN_DATA[count];

			if( (count + 1) == PATTERN_LEN)
				count <= 0;
		end
	end

endmodule

module GP_POR(output reg RST_DONE);
	parameter POR_TIME = 500;

	initial begin
		RST_DONE = 0;

		if(POR_TIME == 4)
			#4000;
		else if(POR_TIME == 500)
			#500000;
		else begin
			$display("ERROR: bad POR_TIME for GP_POR cell");
			$finish;
		end

		RST_DONE = 1;

	end

endmodule

module GP_SHREG(input nRST, input CLK, input IN, output OUTA, output OUTB);

	parameter OUTA_TAP = 1;
	parameter OUTA_INVERT = 0;
	parameter OUTB_TAP = 1;

	reg[15:0] shreg = 0;

	always @(posedge CLK, negedge nRST) begin

		if(!nRST)
			shreg = 0;

		else
			shreg <= {shreg[14:0], IN};

	end

	assign OUTA = (OUTA_INVERT) ? ~shreg[OUTA_TAP - 1] : shreg[OUTA_TAP - 1];
	assign OUTB = shreg[OUTB_TAP - 1];

endmodule

module GP_VDD(output OUT);
       assign OUT = 1;
endmodule

module GP_VSS(output OUT);
       assign OUT = 0;
endmodule