[test] add a new arch to validate that clock network tap supports subtiles
This commit is contained in:
tangxifan
parent
e4d7192e50
commit
e6c508f081
|
|
@ -0,0 +1,506 @@
|
|||
<?xml version="1.0"?>
|
||||
<!--
|
||||
Architecture with no fracturable LUTs
|
||||
|
||||
- 40 nm technology
|
||||
- General purpose logic block:
|
||||
K = 4, N = 4
|
||||
- Routing architecture: L = 4, fc_in = 0.15, Fc_out = 0.1
|
||||
|
||||
Details on Modelling:
|
||||
|
||||
Based on flagship k6_frac_N10_mem32K_40nm.xml architecture. This architecture has no fracturable LUTs nor any heterogeneous blocks.
|
||||
|
||||
|
||||
Authors: Jason Luu, Jeff Goeders, Vaughn Betz
|
||||
-->
|
||||
<architecture>
|
||||
<!--
|
||||
ODIN II specific config begins
|
||||
Describes the types of user-specified netlist blocks (in blif, this corresponds to
|
||||
".model [type_of_block]") that this architecture supports.
|
||||
|
||||
Note: Basic LUTs, I/Os, and flip-flops are not included here as there are
|
||||
already special structures in blif (.names, .input, .output, and .latch)
|
||||
that describe them.
|
||||
-->
|
||||
<models>
|
||||
<!-- A virtual model for I/O to be used in the physical mode of io block -->
|
||||
<model name="io_inpad">
|
||||
<output_ports>
|
||||
<port name="inpad"/>
|
||||
</output_ports>
|
||||
</model>
|
||||
<model name="io_outpad">
|
||||
<input_ports>
|
||||
<port name="outpad"/>
|
||||
</input_ports>
|
||||
</model>
|
||||
</models>
|
||||
<tiles>
|
||||
<tile name="io_top" area="0">
|
||||
<sub_tile name="fpga_input" capacity="6">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_input"/>
|
||||
</equivalent_sites>
|
||||
<output name="inpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="left"></loc>
|
||||
<loc side="top"/>
|
||||
<loc side="right">fpga_input[0:5].clk[0:0]</loc>
|
||||
<loc side="bottom">fpga_input[0:5].inpad[0:0]</loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
<sub_tile name="fpga_output" capacity="6">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_output"/>
|
||||
</equivalent_sites>
|
||||
<input name="outpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="left">fpga_output[0:1].outpad[0:0]</loc>
|
||||
<loc side="top"/>
|
||||
<loc side="right">fpga_output[2:3].outpad fpga_output[0:5].clk[0:0]</loc>
|
||||
<loc side="bottom">fpga_output[4:5].outpad[0:0]</loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
</tile>
|
||||
<tile name="io_right" area="0">
|
||||
<sub_tile name="fpga_input" capacity="3">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_input"/>
|
||||
</equivalent_sites>
|
||||
<output name="inpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="left">fpga_input[0:2].inpad[0:0] fpga_input[0:2].clk[0:0]</loc>
|
||||
<loc side="right"/>
|
||||
<loc side="top"></loc>
|
||||
<loc side="bottom"></loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
<sub_tile name="fpga_output" capacity="3">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_output"/>
|
||||
</equivalent_sites>
|
||||
<input name="outpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="left">fpga_output[0:0].outpad[0:0] fpga_output[0:2].clk[0:0]</loc>
|
||||
<loc side="right"/>
|
||||
<loc side="top">fpga_output[1:1].outpad[0:0]</loc>
|
||||
<loc side="bottom">fpga_output[2:2].outpad[0:0]</loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
</tile>
|
||||
<tile name="io_bottom" area="0">
|
||||
<sub_tile name="fpga_input" capacity="4">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_input"/>
|
||||
</equivalent_sites>
|
||||
<output name="inpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="right">fpga_input[0:3].clk[0:0]</loc>
|
||||
<loc side="bottom"/>
|
||||
<loc side="top">fpga_input[0:3].inpad[0:0]</loc>
|
||||
<loc side="left"></loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
<sub_tile name="fpga_output" capacity="4">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_output"/>
|
||||
</equivalent_sites>
|
||||
<input name="outpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="right">fpga_output[0:1].outpad[0:0] fpga_output[0:3].clk[0:0]</loc>
|
||||
<loc side="bottom"/>
|
||||
<loc side="top">fpga_output[2:2].outpad[0:0]</loc>
|
||||
<loc side="left">fpga_output[3:3].outpad[0:0]</loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
</tile>
|
||||
<tile name="io_left" area="0">
|
||||
<sub_tile name="fpga_input" capacity="4">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_input"/>
|
||||
</equivalent_sites>
|
||||
<output name="inpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="right">fpga_input[0:3].inpad[0:0] fpga_input[0:3].clk[0:0]</loc>
|
||||
<loc side="left"/>
|
||||
<loc side="top"></loc>
|
||||
<loc side="bottom"></loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
<sub_tile name="fpga_output" capacity="4">
|
||||
<equivalent_sites>
|
||||
<site pb_type="fpga_output"/>
|
||||
</equivalent_sites>
|
||||
<input name="outpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="right">fpga_output[0:1].outpad[0:0] fpga_output[0:3].clk[0:0]</loc>
|
||||
<loc side="left"/>
|
||||
<loc side="top">fpga_output[2:2].outpad[0:0]</loc>
|
||||
<loc side="bottom">fpga_output[3:3].outpad[0:0]</loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
</tile>
|
||||
<tile name="clb" area="53894">
|
||||
<sub_tile name="clb">
|
||||
<equivalent_sites>
|
||||
<site pb_type="clb"/>
|
||||
</equivalent_sites>
|
||||
<input name="I" num_pins="10" equivalent="full"/>
|
||||
<output name="O" num_pins="4" equivalent="none"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<fc in_type="frac" in_val="0.25" out_type="frac" out_val="0.20">
|
||||
<fc_override port_name="clk" fc_type="frac" fc_val="0"/>
|
||||
</fc>
|
||||
<pinlocations pattern="custom">
|
||||
<loc side="right">clb.I[0:1] clb.O[0:0]</loc>
|
||||
<loc side="left">clb.I[2:3] clb.O[1:1] clb.clk</loc>
|
||||
<loc side="top">clb.I[4:6] clb.O[2:2]</loc>
|
||||
<loc side="bottom">clb.I[7:9] clb.O[3:3]</loc>
|
||||
</pinlocations>
|
||||
</sub_tile>
|
||||
</tile>
|
||||
</tiles>
|
||||
<!-- ODIN II specific config ends -->
|
||||
<!-- Physical descriptions begin -->
|
||||
<layout tileable="true" perimeter_cb="true">
|
||||
<auto_layout aspect_ratio="1.0">
|
||||
<!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
|
||||
<row type="io_top" starty="H-1" priority="90"/>
|
||||
<row type="io_bottom" starty="0" priority="91"/>
|
||||
<col type="io_right" startx="W-1" priority="92"/>
|
||||
<col type="io_left" startx="0" priority="93"/>
|
||||
<corners type="EMPTY" priority="101"/>
|
||||
<!--Fill with 'clb'-->
|
||||
<fill type="clb" priority="10"/>
|
||||
</auto_layout>
|
||||
<fixed_layout name="2x2" width="4" height="4">
|
||||
<!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
|
||||
<row type="io_top" starty="H-1" priority="90"/>
|
||||
<row type="io_bottom" starty="0" priority="91"/>
|
||||
<col type="io_right" startx="W-1" priority="92"/>
|
||||
<col type="io_left" startx="0" priority="93"/>
|
||||
<corners type="EMPTY" priority="101"/>
|
||||
<!--Fill with 'clb'-->
|
||||
<fill type="clb" priority="10"/>
|
||||
</fixed_layout>
|
||||
</layout>
|
||||
<device>
|
||||
<!-- VB & JL: Using Ian Kuon's transistor sizing and drive strength data for routing, at 40 nm. Ian used BPTM
|
||||
models. We are modifying the delay values however, to include metal C and R, which allows more architecture
|
||||
experimentation. We are also modifying the relative resistance of PMOS to be 1.8x that of NMOS
|
||||
(vs. Ian's 3x) as 1.8x lines up with Jeff G's data from a 45 nm process (and is more typical of
|
||||
45 nm in general). I'm upping the Rmin_nmos from Ian's just over 6k to nearly 9k, and dropping
|
||||
RminW_pmos from 18k to 16k to hit this 1.8x ratio, while keeping the delays of buffers approximately
|
||||
lined up with Stratix IV.
|
||||
We are using Jeff G.'s capacitance data for 45 nm (in tech/ptm_45nm).
|
||||
Jeff's tables list C in for transistors with widths in multiples of the minimum feature size (45 nm).
|
||||
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply drive strength sizes in this file
|
||||
by 2.5x when looking up in Jeff's tables.
|
||||
The delay values are lined up with Stratix IV, which has an architecture similar to this
|
||||
proposed FPGA, and which is also 40 nm
|
||||
C_ipin_cblock: input capacitance of a track buffer, which VPR assumes is a single-stage
|
||||
4x minimum drive strength buffer. -->
|
||||
<sizing R_minW_nmos="8926" R_minW_pmos="16067"/>
|
||||
<!-- The grid_logic_tile_area below will be used for all blocks that do not explicitly set their own (non-routing)
|
||||
area; set to 0 since we explicitly set the area of all blocks currently in this architecture file.
|
||||
-->
|
||||
<area grid_logic_tile_area="0"/>
|
||||
<chan_width_distr>
|
||||
<x distr="uniform" peak="1.000000"/>
|
||||
<y distr="uniform" peak="1.000000"/>
|
||||
</chan_width_distr>
|
||||
<switch_block type="wilton" fs="3"/>
|
||||
<connection_block input_switch_name="ipin_cblock"/>
|
||||
</device>
|
||||
<switchlist>
|
||||
<!-- VB: the mux_trans_size and buf_size data below is in minimum width transistor *areas*, assuming the purple
|
||||
book area formula. This means the mux transistors are about 5x minimum drive strength.
|
||||
We assume the first stage of the buffer is 3x min drive strength to be reasonable given the large
|
||||
mux transistors, and this gives a reasonable stage ratio of a bit over 5x to the second stage. We assume
|
||||
the n and p transistors in the first stage are equal-sized to lower the buffer trip point, since it's fed
|
||||
by a pass transistor mux. We can then reverse engineer the buffer second stage to hit the specified
|
||||
buf_size (really buffer area) - 16.2x minimum drive nmos and 1.8*16.2 = 29.2x minimum drive.
|
||||
I then took the data from Jeff G.'s PTM modeling of 45 nm to get the Cin (gate of first stage) and Cout
|
||||
(diff of second stage) listed below. Jeff's models are in tech/ptm_45nm, and are in min feature multiples.
|
||||
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply the drive strength sizes above by
|
||||
2.5x when looking up in Jeff's tables.
|
||||
Finally, we choose a switch delay (58 ps) that leads to length 4 wires having a delay equal to that of SIV of 126 ps.
|
||||
This also leads to the switch being 46% of the total wire delay, which is reasonable. -->
|
||||
<switch type="mux" name="0" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<!--switch ipin_cblock resistance set to yeild for 4x minimum drive strength buffer-->
|
||||
<switch type="mux" name="ipin_cblock" R="2231.5" Cout="0." Cin="1.47e-15" Tdel="7.247000e-11" mux_trans_size="1.222260" buf_size="auto"/>
|
||||
</switchlist>
|
||||
<segmentlist>
|
||||
<!--- VB & JL: using ITRS metal stack data, 96 nm half pitch wires, which are intermediate metal width/space.
|
||||
With the 96 nm half pitch, such wires would take 60 um of height, vs. a 90 nm high (approximated as square) Stratix IV tile so this seems
|
||||
reasonable. Using a tile length of 90 nm, corresponding to the length of a Stratix IV tile if it were square. -->
|
||||
<segment name="L1" freq="0.900000" length="1" type="unidir" Rmetal="101" Cmetal="22.5e-15">
|
||||
<mux name="0"/>
|
||||
<sb type="pattern">1 1</sb>
|
||||
<cb type="pattern">1</cb>
|
||||
</segment>
|
||||
<segment name="L4" freq="0.100000" length="4" type="unidir" Rmetal="101" Cmetal="22.5e-15">
|
||||
<mux name="0"/>
|
||||
<sb type="pattern">1 1 1 1 1</sb>
|
||||
<cb type="pattern">1 1 1 1</cb>
|
||||
</segment>
|
||||
</segmentlist>
|
||||
<complexblocklist>
|
||||
<!-- Define I/O pads begin -->
|
||||
<!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
|
||||
<!-- Not sure of the area of an I/O (varies widely), and it's not relevant to the design of the FPGA core, so we're setting it to 0. -->
|
||||
<pb_type name="fpga_input">
|
||||
<output name="inpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<mode name="physical" disable_packing="true">
|
||||
<pb_type name="iopad" blif_model=".subckt io_inpad" num_pb="1">
|
||||
<output name="inpad" num_pins="1"/>
|
||||
</pb_type>
|
||||
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
||||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="clk" input="fpga_input.clk" output="ff.clk"/>
|
||||
<!-- Create a selector between registered/combinational I/O -->
|
||||
<direct name="inpad" input="iopad.inpad" output="ff.D"/>
|
||||
<mux name="mux1" input="iopad.inpad ff.Q" output="fpga_input.inpad">
|
||||
<delay_constant max="4.5e-11" in_port="iopad.inpad" out_port="fpga_input.inpad"/>
|
||||
<delay_constant max="4.243e-11" in_port="ff.Q" out_port="fpga_input.inpad"/>
|
||||
</mux>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<!-- IOs can operate as either inputs or outputs.
|
||||
Delays below come from Ian Kuon. They are small, so they should be interpreted as
|
||||
the delays to and from registers in the I/O (and generally I/Os are registered
|
||||
today and that is when you timing analyze them.
|
||||
-->
|
||||
<mode name="inpad">
|
||||
<pb_type name="inpad" blif_model=".input" num_pb="1">
|
||||
<output name="inpad" num_pins="1"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="inpad" input="inpad.inpad" output="fpga_input.inpad">
|
||||
<delay_constant max="4.243e-11" in_port="inpad.inpad" out_port="fpga_input.inpad"/>
|
||||
</direct>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<mode name="inpad_registered">
|
||||
<pb_type name="inpad" blif_model=".input" num_pb="1">
|
||||
<output name="inpad" num_pins="1"/>
|
||||
</pb_type>
|
||||
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
||||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="clk" input="fpga_input.clk" output="ff.clk"/>
|
||||
<direct name="inpad" input="inpad.inpad" output="ff.D">
|
||||
<pack_pattern name="registered_io" in_port="inpad.inpad" out_port="ff.D"/>
|
||||
</direct>
|
||||
<direct name="ff2inpad" input="ff.Q" output="fpga_input.inpad"/>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<power method="ignore"/>
|
||||
</pb_type>
|
||||
<pb_type name="fpga_output">
|
||||
<input name="outpad" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<!-- A mode denotes the physical implementation of an I/O
|
||||
This mode will be not packable but is mainly used for fabric verilog generation
|
||||
-->
|
||||
<mode name="physical" disable_packing="true">
|
||||
<pb_type name="iopad" blif_model=".subckt io_outpad" num_pb="1">
|
||||
<input name="outpad" num_pins="1"/>
|
||||
</pb_type>
|
||||
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
||||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="clk" input="fpga_output.clk" output="ff.clk"/>
|
||||
<!-- Create a selector between registered/combinational I/O -->
|
||||
<direct name="outpad-D" input="fpga_output.outpad" output="ff.D"/>
|
||||
<mux name="mux1" input="fpga_output.outpad ff.Q" output="iopad.outpad">
|
||||
<delay_constant max="4.5e-11" in_port="fpga_output.outpad" out_port="iopad.outpad"/>
|
||||
<delay_constant max="4.243e-11" in_port="ff.Q" out_port="iopad.outpad"/>
|
||||
</mux>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<!-- IOs can operate as either inputs or outputs.
|
||||
Delays below come from Ian Kuon. They are small, so they should be interpreted as
|
||||
the delays to and from registers in the I/O (and generally I/Os are registered
|
||||
today and that is when you timing analyze them.
|
||||
-->
|
||||
<mode name="outpad">
|
||||
<pb_type name="outpad" blif_model=".output" num_pb="1">
|
||||
<input name="outpad" num_pins="1"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="outpad" input="fpga_output.outpad" output="outpad.outpad"/>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<mode name="outpad_registered">
|
||||
<pb_type name="outpad" blif_model=".output" num_pb="1">
|
||||
<input name="outpad" num_pins="1"/>
|
||||
</pb_type>
|
||||
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
||||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="clk" input="fpga_output.clk" output="ff.clk"/>
|
||||
<direct name="inpad" input="fpga_output.outpad" output="ff.D">
|
||||
<pack_pattern name="registered_io" in_port="fpga_output.outpad" out_port="ff.D"/>
|
||||
</direct>
|
||||
<direct name="ff2outpad" input="ff.Q" output="outpad.outpad"/>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<power method="ignore"/>
|
||||
</pb_type>
|
||||
<!-- Define I/O pads ends -->
|
||||
<!-- Define general purpose logic block (CLB) begin -->
|
||||
<!--- Area calculation: Total Stratix IV tile area is about 8100 um^2, and a minimum width transistor
|
||||
area is 60 L^2 yields a tile area of 84375 MWTAs.
|
||||
Routing at W=300 is 30481 MWTAs, leaving us with a total of 53000 MWTAs for logic block area
|
||||
This means that only 37% of our area is in the general routing, and 63% is inside the logic
|
||||
block. Note that the crossbar / local interconnect is considered part of the logic block
|
||||
area in this analysis. That is a lower proportion of of routing area than most academics
|
||||
assume, but note that the total routing area really includes the crossbar, which would push
|
||||
routing area up significantly, we estimate into the ~70% range.
|
||||
-->
|
||||
<pb_type name="clb">
|
||||
<input name="I" num_pins="10" equivalent="full"/>
|
||||
<output name="O" num_pins="4" equivalent="none"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<!-- Describe basic logic element.
|
||||
Each basic logic element has a 4-LUT that can be optionally registered
|
||||
-->
|
||||
<pb_type name="fle" num_pb="4">
|
||||
<input name="in" num_pins="4"/>
|
||||
<output name="out" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<!-- 4-LUT mode definition begin -->
|
||||
<mode name="n1_lut4">
|
||||
<!-- Define 4-LUT mode -->
|
||||
<pb_type name="ble4" num_pb="1">
|
||||
<input name="in" num_pins="4"/>
|
||||
<output name="out" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<!-- Define LUT -->
|
||||
<pb_type name="lut4" blif_model=".names" num_pb="1" class="lut">
|
||||
<input name="in" num_pins="4" port_class="lut_in"/>
|
||||
<output name="out" num_pins="1" port_class="lut_out"/>
|
||||
<!-- LUT timing using delay matrix -->
|
||||
<delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
|
||||
261e-12
|
||||
261e-12
|
||||
261e-12
|
||||
261e-12
|
||||
</delay_matrix>
|
||||
</pb_type>
|
||||
<!-- Define flip-flop -->
|
||||
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
||||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="direct1" input="ble4.in" output="lut4[0:0].in"/>
|
||||
<direct name="direct2" input="lut4.out" output="ff.D">
|
||||
<!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
|
||||
<pack_pattern name="ble4" in_port="lut4.out" out_port="ff.D"/>
|
||||
</direct>
|
||||
<direct name="direct3" input="ble4.clk" output="ff.clk"/>
|
||||
<mux name="mux1" input="ff.Q lut4.out" output="ble4.out">
|
||||
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
||||
<delay_constant max="25e-12" in_port="lut4.out" out_port="ble4.out"/>
|
||||
<delay_constant max="45e-12" in_port="ff.Q" out_port="ble4.out"/>
|
||||
</mux>
|
||||
</interconnect>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="direct1" input="fle.in" output="ble4.in"/>
|
||||
<direct name="direct2" input="ble4.out" output="fle.out[0:0]"/>
|
||||
<direct name="direct3" input="fle.clk" output="ble4.clk"/>
|
||||
</interconnect>
|
||||
</mode>
|
||||
<!-- 6-LUT mode definition end -->
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<!-- We use a full crossbar to get logical equivalence at inputs of CLB
|
||||
The delays below come from Stratix IV. the delay through a connection block
|
||||
input mux + the crossbar in Stratix IV is 167 ps. We already have a 72 ps
|
||||
delay on the connection block input mux (modeled by Ian Kuon), so the remaining
|
||||
delay within the crossbar is 95 ps.
|
||||
The delays of cluster feedbacks in Stratix IV is 100 ps, when driven by a LUT.
|
||||
Since all our outputs LUT outputs go to a BLE output, and have a delay of
|
||||
25 ps to do so, we subtract 25 ps from the 100 ps delay of a feedback
|
||||
to get the part that should be marked on the crossbar. -->
|
||||
<complete name="crossbar" input="clb.I fle[3:0].out" output="fle[3:0].in">
|
||||
<delay_constant max="95e-12" in_port="clb.I" out_port="fle[3:0].in"/>
|
||||
<delay_constant max="75e-12" in_port="fle[3:0].out" out_port="fle[3:0].in"/>
|
||||
</complete>
|
||||
<complete name="clks" input="clb.clk" output="fle[3:0].clk">
|
||||
</complete>
|
||||
<!-- This way of specifying direct connection to clb outputs is important because this architecture uses automatic spreading of opins.
|
||||
By grouping to output pins in this fashion, if a logic block is completely filled by 6-LUTs,
|
||||
then the outputs those 6-LUTs take get evenly distributed across all four sides of the CLB instead of clumped on two sides (which is what happens with a more
|
||||
naive specification).
|
||||
-->
|
||||
<direct name="clbouts1" input="fle[3:0].out" output="clb.O"/>
|
||||
</interconnect>
|
||||
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
||||
<!-- Place this general purpose logic block in any unspecified column -->
|
||||
</pb_type>
|
||||
<!-- Define general purpose logic block (CLB) ends -->
|
||||
</complexblocklist>
|
||||
</architecture>
|
||||
Loading…
Reference in New Issue