* Change: In Anabatic::AutoContactTerminal::getNativeConstraintBox(),
when the anchor is a RoutingPad (which must be always the case),
perform the true computation of it's position based on the
segment occurrence. It is a important change, previously the
area was in fact the "center line" of the connector while now
it is really an area (mandatory for "half-offgrid" terminals of
real technologies).
The change is not complete yet, the area should be shrinked
by the half size of a VIA, because the area applies to the center
coordinate of the VIA (to be done quickly).
* Bug: In Anabatic::AutoContactTurn::updateTopology(), when a dogleg
is created (restore connexity after a layer change) the layer of
the VIA, based on the segments it connects to must be re-computed
*after* the dogleg has been made.
* Change: In all files of Anabatic, when comparing two layers, no longer
use the Layer pointer itself, but the layer mask. This allow a
transparent management of both real and symbolic layers (which
do share the same mask). Real metal layers (not VIAs) will be
BasicLayer and symbolic metal layers will be RegularLayer.
* New: Anabatic::Configuration::selectRpComponent(), select the best
RoutingPad component for metal1 terminals. Look for the metal1
component with the biggest accessibility on-grid.
RoutingPad using other metals are left untoucheds.
* New: New function Anabatic::Vertex::getNeighbor(Edge*) to get the
neighbor Vertex through an Edge*. This method allows to write
clearer code as we no longer need to access the neighbor through
the underlying GCell.
Also add proxies for GCell methods in Vertex.
* Bug: In Anabatic::Dijkstra::_toSources(), in the ripup stage, when
a component with multiples vertexes is reached *and* two of it's
vertexes are reached *at the same time* (one from which we backtrack
and one still in the queue) extraneous edges may be created by
_materialize(). Case occurs on snx/c35b4, "abc_5360_n903_1".
To solve this, Dijkstra::_toSource() is modificated, the "from"
edges of the newly reacheds vertexes are reset to NULL, *except*
for the one we will be backtracking from. That is, the one given
in the source argument.
* Change: In Anabatic::NetBuilder class, put the various Hooks and
RoutingPad sorting functions as class ones.
* Bug: In AutoSegment::setLayer(), raise the SegInvalidatedFayer flag.
This unset flag was causing AutoContactTurn::updateTopology()
to not work as expected and making gaps, this was the cause of
the last remaining warnings about layer connexity.
* New: In AnabaticEngine::invalidateRoutingPads() this method is a temporary
workaround for a Hurricane problems. When an instance is moved, the
RoutingPads that use it must be moved accordingly, but they are not
invalidated so they stay in the wrong QuadTree.
New method ::_resizeMatrix() to be called when the associated Cell
is resized.
* Bug: In AutoHorizontal::getConstraints() and AutoVertical::getConstraints(),
the *target* constraints where never merged.
* Change: In AutoHorizontal::getCells() and AutoVertical::getGCells(),
now return a boolean to tell if it was ok (must not encounter a NULL
GCell while progessing from source to target).
* New: In Anabatic::Configuration and Anabatic:Session, create new methods:
- getDHorizontalLayer()
- getDhorizontalDepth()
- getDHorizontalWidth()
- getDHorizontalPitch()
And so on for Vertical and Contact.
They supply depth-independant informations about the H/V layers to
build the initial detailed routing.
The AutoSegment::create() methods have been modificated accordingly.
* New: In Anabatic::GCell, add two new types "StdCellRow" and "ChannelRow"
for implementing 2-Metal blocks.
Rename the GCell::setXY() method in GCell::setSouthWestCorner(),
move the contents of GCell::updateContactsPosition() into it and
suppress it.
WARNING: In case of a GCell shrink this may cause problems. But for
now we only expand...
New method GCell::getNetCount() to count the number of Net going
though the GCell.
* Change: In Anabatic::Edge, add specific support for capacity of 2-Metal
routing channels.
* Change: In Anabatic::Dijsktra various methods, replace the "gcell->isMatrix()"
calls by "not gcell->isAnalog()". Add more check so that the methods
pertaining to the analog routing (GRData) are not called in digital
mode.
* New: In Anabatic::Dijkstra::materialize(), add support for 2-Metal specific
cases. That is, always break in case of vertical pass-through or
U-turn. The global routing must always be broken in H-Channel.
* New: In Anabatic::GCell & Anabatic::Edge, make use of the Session mechanism
to ensure the revalidation. The "::revalidate()" method is then moved
as "::materialize()" (overload of Go) and "::_invalidate()" becomes
"::invalidate()"
* Change: In LoadGlobalRouting, cosmetic rename of SortHkByX in SortHookByX.
* New: In GCellTopology, added support for building 2-Metal topologies.
* ForkStack is now an object attribute as many methods do need it.
* To push segments/hook on the stack, a new method "push()" is
available. Perform NULL and fromHook checking. Can also setup
_southWestContact or _northEastContact if it is the "from" edge.
* N/S/E/W edges are now vector as in digital channel mode there
can be more than one.
* Added build topological build methods:
- doRp_2m_Access() RoutingPad stem access.
- _do_2m_1G_1M1() North or south access.
- _do_2m_2G_1M1() North AND south access.
- _do_2m_xG() H-Channel routing.
* New: In Anabatic::Matrix, new ::resize() function, as Cell can be resizeds.
* New: In Anabatic::Vertex, new static method ::getValueString() for a
friendly text rendering.
* New: In Katana::DigitalDistance, support for channel routing.
* Change: In KatanaEngine::digitalSetup() and KatanaEngine::runGlobalrouter(),
for channel routing, calls to setupPowerRails() and
protectRoutingPads() must be called after the core block has
been fully dimensionned.
::runGlobalrouter() contains the code tasked with the grid creation
and channel sizing.
* New: In KatanaEngine: Added support for core block, for 2-Metal routing.
May be expanded for over-the-cell routing in the future.
Added methods :
- isDigitalMode()
- isAnalogMode()
- isMixedMode()
- isChannelMode()
- getBlock() / addBlock()
- setupChannelMode()
- createChannel()
* New: In Katana, new class Block to manage core blocks and perform
channel routing.
* New: In Katana::Session, new convenience method "isOpen()".
in Dijkstra.cpp/.h, Edge.cpp/.h, GCell.cpp/.h:
*Change: GlobalRouting wires can have different wires' width. One Net's wires has one width only.
in NetRoutingProperty.cpp/.h, PyNetRoutingProperty.cpp/.h:
*New: A wire width parameter is added. It can be set through python script.
* Change: In Hurrican::Component::_preDestroy(), the cascaded destruction
of slaves Components and subsequent ring merge and Rubber creation
was using set<> sorted on pointer values. This was making the order
of destruction of the slaves components non-deterministic. Now the
sets are sorted according to their id (see Entity).
* Change: In Hurricane::SharedProperty, the _ownerSet is now a vector<>
instead of a set<>. This will slow the search process, but hopefully
this is needed only during construction/destruction of a Property
so the slow down shouldn't be too much.
This has also an impact on Hurricane::Relation.
* Bug: In Anabatic::RawGCellsUnder, *again*, the north and east borders
of the whole area *are* includeds (shut up disgraceful warning).
* New: In Anabatic::GCell, add a display mode to select between boundary
display (for analogic) and density display (for numeric).
* Bug: In KatanaEngine::runGlobalRouter(), do not check if an Edge cannot
be desatured when the vector or overloaded Edges is empty.
(one less disgraceful warning)
* New: In GraphicKatanaEngine::drawGCell(), support for drawing the GCells
in density mode. Use the fire scale and the MaxDensity mode.
Setup the GCell drawing mode in GraphicKatanaEngine::initGCell().
* Change: In GraphicKatanaEngine::drawEdge(), adjust the various thresholds
for showing the Edge and its label.
* New: In CRL Core, adds "anabatic.gcell.displayMode" to the set of Anabatic
parameters.
Adjust the showing threshold for GCells in "display.conf" so when the
zoom level is low, we still can see the density map.
* Change: In Anabatic:
- Long wires, going straight accross multiple GCells were splitted
into a long sequence of segment+contact, one for each gone-through
GCell. It was memory-consuming and algorithmically inefficient.
Now there is only one straight wire.
As a consequence, Edges now store the list of all segments
going through them. That way we do not need to load a Net into
Dijkstra before riping up some of it's segment. The ripup mechanims
can now be implemented right at AnabaticEngine level, without
dependencies over Dijkstra. Note that long wires are automatically
broken in two if we need to attach a new branch on it (breakAt()).
And fused back into one if a branch is removed (unify()).
* Bug: In Hurricane, in tstream (Commons.h), in the *template* overload of
operator<<(), do not use the operator<<() of ostream as it will be
looked up in "stage 1" (template definition) and so will miss all the
overloads added later and built over getString<>(). Instead, make use
of getString<>(), which, as another template will be looked up in
"stage 2" (template instanciation) and at that point will have all the
needed template specialisation of getString<>().
We also need to define new stream manipulators to be able to create
a matching template overload not dependant from the implementation.
To avoid name clashes, we prefix a 't'. For now, only 'tsetw()' is
refined.
As a side effect, we cannot directly print bit-fields into the stream,
we must go through an intermediate variable (happens once in AutoContact).
* New: In Anabatic:
- In AnabaticEngine, keep track of overflowed edges.
- In AnabaticEngine, getNetsFromedge() to lookup all nets going
through an Edge.
- In Configuration, read the Kite "reserved local" parameter to
decrease the Edge capacity (it's a guessing of the cost of the
local routing).
- In Edge, add an attribute to know if there is an associated
segment of the current net (set by Dijkstra::_traceback()).
Transparently manage the overflowed edges.
- In GCell_Edges, correct a filtering bug when not all sides are
selecteds.
- New GCell::getEdgeTo() to find the edge between two adjacent
GCells.
- New GCell::unrefContact() to automatically removes global contacts
no longer used by any global segments (used during the ripup
step).
- In Dijkstra::load(), now able to "reload" and already partially
or completly routed net (look for Contact of "gcontact" layer
and their attached segments).
- In Dijkstra, keep the last net loaded until the next one is.
Put the cleanup operations in an isolated function "_cleanup()".
- In Dijkstra::_selectFirstsource() and run(), load first source
component made of multiple vertexes.
- In Dijkstra::_trackback(), link the Net segments to the Edges.
- New Dijkstra::ripup(), Dijkstra::_propagateRipup() to perform
the ripup of one edge of a Net (must be loaded in Dijkstra first).
Dijkstra::_tagConnecteds() setup the connexId of a set of Vertexes
- that are connecteds through edges *with* segments.
- In GraphicAnabaticengine & GlobalRoute.cpp, embryo of a global
routing tool with ripup & reroute.
* Bug: In Anabatic:
- In _propagate(), on reaching a target, forgot to remove it from
the queue before pushing it back with the new distance. It also
simplificate the core algorithm as target as treated normal nodes.
* New: In Anabatic:
- Update cdebug to use the fastest macro version.
- More readable drawings of GCells and Edges.
- Added timer support.
- The distance is now computed in DbU::Unit (aka long) and not in
normalized float.
- The distance function is now a callback (std::function<>) that
can be changed (a default is provided at initialization).
- New concept of branch in the agglomerated connex component.
Each trace back part create a "branch" (tagged with a "branchId").
When a node is reached with the same distance, but from two
different branches, choose the the branch that was lastly created.
This create a slightly different tree which grows outward from
the newest branches.
- Makes the horizontal edges *slightly* longer than the vertical ones
to skew the tree to use vertical edges, as it is usually less
congested than the horiontal one (due to metal1 cell terminals).
It is also my understanding that it is useful to reduce the
number of vias, whithout introducing a via cost.
* New: In Bootstrap:
- Script sprof.py to perform sprof & demangle libraries execution
profile.
* ToDo: In Anabatic:
- Corner optimization. Sometimes when two corners are possible, the
wrong one is choosen. That is, one of it's edge cannot be used for
further grow of the tree.
* Bug: In Anabatic:
- In Dijktra::load(), do not create Contact while looping over the Net's
components (for RoutingPads).
- In Dijkstra::propagate(), reset the connexId of reached Vertexes
on updating the stamp to avoid using connexId from previous runs.
Push the vertexes on the queue while backtracking (with a distance
of 0.0). Do not reset the "_from" as we need it in Dijkstra::toWires()
to know how were the routing is.
- In Edge::getDistance(), convert to float more early so the normalisation
do not always end up in zero.
- In GCell::_add(), when the axis of the new edge is equal to one already
on the given side, adds it *after* the existing edge and not before.
(to be coherent with the way GCells are split in two)
- In GCell::hcut() and GCell::vcut(), create an Edge if is equal to X/Y Max,
*but* the new chunk is flat. The new chunk is then expected to expand
"below".
- In GraphicsAnabaticEngine::drawGCell(), display the id of the GCell in
a small box at the center of it's bounding box. Nothing displayed for
flat GCells, to avoid cluttering.
* Bug: In Anabatic:
- In Edge, materialize was done before the Edge get it's final position.
Must be invalidated afterwards for the UpdateSession to put him in
the correct QuadTree.
- Functional (debugged) Dijkstra skeleton.
* Change: In Hurricane, in CellWidget, enable the drawing of ExtensionGos
according to the the threshold paramaters (as layers do).
* Change: In CRL Core, provide DrawingStyle for Anabatic::GCell &
Anabatic::Edge. Use the exact name of the ExtensionGo.
In kite.conf, add settings for the size of an edge as the optimal
size may change between analog & digital designs.
* New: In Anabatic:
- Support for fast position query using a matrix.
- Computation of the Edge capacity, based on the routing gauge parameters.
- Graphic display of the edges capacity. Added configuration
parameters to size the bounding box of an Edge.
* Bug: In Anabatic:
- GCell::_moveEdges was both too complex (some cases never arise the
way we divide GCells) and bugged.
Jean-Paul Chaput
EricLaoGitHub