Fixes issue with big endian hosts and mis-aligned data on some hosts.
Fixes unaligned access exception on hosts that do not support unaligned
access when debugging some arm targets.
Signed-off-by: Jason Moehlman <jmoehlma@linux-software.com>
Change-Id: I6bc6fb1b3c3565b256674b9ef43ed2afd14f5178
Reviewed-on: http://openocd.zylin.com/996
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Other than a larger memory layout these new devices also have an extra
MER1 bit to perform the mass erase.
Change-Id: I7110a05bac95c1707160d1f5622181664291eb4a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/985
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
No function writes to MIPS32_PRACC_PARAM_IN addresses and probably has no much sense.
Any attempt to write to those addresses should be an error.
Change-Id: Iebea5fa9954e2cd56ad34976dd7d25009c6e6388
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/975
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Current code needs 101 pracc accesses for this function, this code needs 12 less.
There is a singularity in this code, is the only function that restore
a register from param out instead from pracc stack. Obviously the register
was previously stored at param out. This save 2 pracc accesses.
Change-Id: Ie95b6f983a3198dafc0eab2dd5acc11f871a8d83
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/958
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
All the the loads are done with lui and ori instructions, there is
no need to save any register, they will be overwritten.
Like in the previous patch, for speed optimization in write code,
same instructions can be saved if the lower half word or the upper
half word is 0.
If the lower half word is 0, it can be loaded with only a lui instruction.
If the higher half word is 0 it can be done with an ori instruction with register 0.
This code saves 10 pracc accesses at a minimum, and 40 at a maximum,
obviously if register 2 to 31 are 0 or a half word is 0
Current code needs 91 pracc accesses.
Change-Id: I892c5b440191d0c7a474c96845d41c373b7fc637
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/957
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
All the writes are done by the new function mips32_pracc_write_mem_generic().
The code is similar to the read generic code.
The reuse of register 15 as memory base address saves 3 pracc accesses.
The first write takes 13(12) pracc accesses and for additional writes 3(2).
Loading miniprograms should take 25% less time and loading fastdata transfer
handler code should be over 2x faster.
Change-Id: Ia3b24ba084af33be99da19f00a7fd4d1b291f350
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/956
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Really nothing new that not explained in previous patches.
The code is expanded as needed, there are no loops in pracc code.
For the first value pracc accesses are reduced from 39 to 16
and for aditional values from 10 to 3.
dump_image should work around 3x faster.
Change-Id: I37c9b13395c09eb52a91f10cdb6cbaedef8ab98b
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/955
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This function is highly optimized, there is not much to
improve.
Loading the base address for pracc access with the new
defined MIPS32_PRACC_BASE_ADDR saves one instruction.
The memory address is loaded in too steps. First the upper
address is loaded. The lower address is passed as an offset in
the memory load instruction.
The offset is signed, if the lower address is in the range of
0x8000 to 0xffff the offset is a negative value, and the upper
address must be incremented by 1.
Pracc accesses are now 12 instead of 14.
Change-Id: I286945b240ed5c5d5cc540780a41a8a5fa075da3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/952
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
MIPS32_PRACC_BASE_ADDR is defined as 0xFF200000. Now is
possible to load the base address with a lui instruction and
only one pracc access.
Offsets to the pracc code addresses are defined to simplify the code
and probably make it a bit more readable or self-explained.
Change-Id: I853dd2d7fad52745931cc6e6be68c0ae156d897e
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/951
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
The function mips_ejtag_read_debug() is defined in mips_ejtag.c
and is called only by mips_m4k_debug_entry() for reading the
CP0 debug register. The comment in this function is obviously wrong.
There is a generic function to read CP0 registers with similar code.
A call to mips32_cp0_read() should work in the same way.
The purpose of reading the debug register is to test if the DSS
bit is set and clear the SSt bit.
It is faster and easier if the SSt bit is cleared without any check.
Remark: DSS bit set only means that a debug single-step exception
ocurred, but it is not possible to step over a sdbbp instruction,
in this case DSS will not be set and the SSt bit not cleared by code.
Resume command at another address will step, so really the behavior
is not the same.
Change-Id: Ibd35f80e0f7669976d96f4ed813830cecf587971
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/950
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code is a bit large compared to mips_ejtag_step_enable().
With the mips32 xori instruction the code can be
reused.
The number of pracc accesses are reduced from 18 to 7.
Change-Id: If3974ebd64da4461c22b089796646990e68e1b72
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/944
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This reverts commit 452248af1d. This change
breaks all non-high speed adapters. The patch was not tested and did not get
any review.
Change-Id: Ib38fd242a202fd7c5a8711d9f857cd8f586df44e
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/973
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit c4ab127b40 introduces a copy&paste error which affects
the detection of the current thread.
As a result, the stack of the current thread won't be detected
correctly in most cases.
Change-Id: Ib46b8f64be8053d7e9103f427c66796963214419
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/974
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
An issue was observed when using an async algorithm with a target that had
not been previously reset beforehand. The target would enter a infinite
loop within target_run_flash_async_algorithm.
Add a timeout that will at least prevent this issue from happening. and also
suggest the user resets the target.
Change-Id: I5277e0d64e252d3d353e8d5bc9889a37fdc63060
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/949
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The order of the mrc/mcr command matches the ARM Architecture Reference
Manual. This patch corrects the help information for mrc/mcr.
Change-Id: I1f0e6a628a3644124591a6aa291b8a58cfd93b44
Signed-off-by: Karl Kurbjun <kkurbjun@gmail.com>
Reviewed-on: http://openocd.zylin.com/914
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If we halt due to a breakpoint make sure that we do not remove it during a
step, only remove breakpoints we have created.
Change-Id: I060168e54e53637d4fbf3cbcf62072efdb353807
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/947
Tested-by: jenkins
This occurs when stepping past a breakpoint on a even address with
maskisr option set to auto
With -d3 the following log message appears in this case:
"Debug : Interrupt handlers didn't complete within time,
leaving target running"
Cause : Given a breakpoint is set on the lower half word and the PC is on
the upper half word. When another breakpoint is now set on the current PC
then resuming the core will not result in a break on the newly set
breakpoint. This has been observed on a STM32F1x, STM32F2x (CM3) but not
on a STM32F0x (CM0). It's not clear if this is a STM32F1/F2 only or a
general CM3 problem.
Change-Id: I384813f3bfdf935373b5e23cdb2d7f243c70cc00
Signed-off-by: Peter Horn <peter.horn@bluewin.ch>
Reviewed-on: http://openocd.zylin.com/864
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added in spi device table SPI Flash Winbond W25Q64CV 64Mbit
Its Device ID 0x001740ef is the same as Spansion S25FL064K (may
be a clone?)
Change-Id: I3cdbd182a0ccde75c78684cb9d54c76059bf34e0
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/928
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ChibiOS code was derived from other RTOS support code which
does not honor the target vs. host endiness.
The other RTOS code still needs to be fixed.
Change-Id: Idf42cfaa30945289bf1756ad6491fff84913eda9
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/962
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The stacking of ChibiOS/RT depends on the usage of an FPU. If the
FPU is enabled the FPU registers are also saved on context switch.
This patch adds automatic detection of FPU for armv7m targets.
Note: With this patch, openocd will only output an error message
warning that the FPU is enabled.
For further FPU support, the correct stacking information
also needs to be added.
Change-Id: I0984cbd9180f247ba2fa610e74a6413cc54239ea
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/961
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We already have the address of the ReadyList provided by gdb.
It is wrong to resolve that address a second time and it only
works by accident.
Change-Id: I82fa2360931c416290cd7f83e1883f86f90dedc2
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/959
Reviewed-by: Joel Bodenmann <joel@unormal.org>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems ST have changed the ref manual (RM0313 rev1) and reverted to using
letters rather than numbers for the stm32f3x family.
Change-Id: I3a87ec9b0b2447d57dfef98603d30e28fe9ac927
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/926
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
The rtos layer was incorrectly handling a qCRC packet as a qC packet.
Make sure we check for the qCRC packet and return unhandled so the gdb
server gets a chance to handle it.
This packet is used in the gdb compare-sections cmd.
Change-Id: I21f8e5fa7225fccd13d65cf9e40186895065a7e3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/933
Tested-by: jenkins
Reviewed-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
All the packets received will be at start of the packet buffer, so use
more efficient strncmp.
Change-Id: Ib9c45d8f53425367006b1f880c1bde27f03a6cf9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/932
Tested-by: jenkins
Reviewed-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
The meminfo command cannot exist if the malloc.h header is not
present.
Cannot get the mac address without sys/ioctl.h and SIOCGIFHWADDR
defined
Change-Id: Ifc0fb98c3a60c53ad2e19473e08b34c460529d0b
Signed-off-by: Edgar Grimberg <edgar.grimberg@gmail.com>
Reviewed-on: http://openocd.zylin.com/912
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
rtos->current_thread is of type int64_t. All other commands already
respect this.
Change-Id: I9951946ff2a09c53cd78c6ab882c80cdd2ab7ac6
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/917
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Use ARRAY_SIZE in helper/types.h to determine the size of the
symbol list.
Change-Id: Icc9838323510f8602efa5d0162a4daed33f863b9
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/935
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
linux_get_symbol_list_to_lookup allocates to few memory. On 64 bit
systems the error did not show due to char* being twice its size,
leaving accidentally enough space.
This patch makes linux_get_symbol_list_to_lookup behave identical
to all other RTOS.
Change-Id: I290ea241fb20b65585c8be14609a92fdbd2a307d
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/934
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This reverts commit 1e7e594452.
For some reason the above commit added a reply to the restart command - this is
not required as per the gdb docs.
Newer versions of gdb (7.0 and above) will complain about this reply.
Change-Id: Ieeae3dcf44d798a91dfc6f7348da982c2ce1be31
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/910
Tested-by: jenkins
Reviewed-by: Joel Bodenmann <joel@unormal.org>
Seems after a reset the stlink is not clearing the vector catch (VC_CORERESET)
in the Debug Control Register.
This has the side effect if the user presses an external reset the core will
halt, this patch fixes that.
Change-Id: Ic3b2c3991b79cacbbd901c02b79613c2e204e71f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/905
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Seems versions of gdb > 6.8 require an W stop reply after receiving a
kill packet.
Without this we receive the following error from gdb:
gdb/thread.c:72: internal-error: inferior_thread: Assertion `tp' failed.
Change-Id: I86765a321f0429c9b517fe13ded0ee2dbd4b2f87
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/911
Tested-by: jenkins
Reviewed-by: Joel Bodenmann <joel@unormal.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Flash algorithm for LPC17xx/LPC2xxx was trying to "reuse" previously
allocated working area on next flashing which is not possible -
working areas are freed automatically on reset. This caused all but
first flashing attempts to fail. As there is no point in storing pointer
to working area, it was converted to local variable.
Change-Id: I939946325ff9eecc4861c0f51ab0f73871a3d7b9
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do some cleanup in lpc2000.c - concatenate short lines into single
longer lines, move variable declarations to "just before" they are
used, etc.
Change-Id: Ia7b9f0307dd4857ee8e15c8a6d4d7b5c4392fd80
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/861
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds ChibiOS/RT support. This patch requires at least
ChibiOS/RT development version starting from SVN revision 4734.
Note, that the Thread structures depend not only on the target
but also on the ChibiOS configuration at build time.
To correct this ChibiOS includes a new "memory signature" which
specifies the offsets.
Special thanks go to Peter Stuge and Spencer Oliver for their
continous input and feedback to this patch.
Change-Id: I842bf7ba6c2309a4efe93d29ea6cd0784a8b22a3
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/901
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
No change to code, just fix some formatting issues.
Change-Id: I177430a99bfecbf90a1ddf623321c29d4db516b0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/906
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Commit 43902905bb fixed a bug but also
introduced a regression. The RTOS GDB packet handler is always called,
not only when an RTOS is actually configured, so it is important to
check if an RTOS has been configured or not before actually processing
the qSymbol packet.
Change-Id: I1aed54f6c2817e1ebf99ddcda051df4554ea5a3a
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/907
Tested-by: jenkins
Since stlink is a special case it presents the same CPU core under a
different name, so copy the configuration to account for that.
Change-Id: I9febf79b388301bde6211d185b5b8161cdadb9ff
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/652
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
With the current timeout setting i = 10 in drtc_run_timeout()
I get "Error: too many retries waiting for DTC status" when
loading a program into the FLASH of an STM32F1.
By experimentation a value of i = 22 was found to be the minimum
on my system. Therefore the value has been increased to i = 50.
Change-Id: Ib67fc648ccaad305871b81c2c39e49de53c330a0
Signed-off-by: Peter Horn <peter.horn@bluewin.ch>
Reviewed-on: http://openocd.zylin.com/863
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The erase time for the option byte page is not directly specified but is
assumed to be the same as the other pages (or mass erase) which is 20 to
40 ms. The current timeout value is 10 which means 10 ms plus the time to
poll the status flag that many times.
With faster interfaces or drivers (such as when using the ftdi driver
instead of the ft2232 driver) the adapter delay is not enough in some
cases, unless the jtag freq is reduced as a workaround. The result is a
"timed out waiting for flash" error when trying to write the options.
Increase the timeout to a minimum of 100 ms, which is in line with the
other erase timeouts. Also make defines of both the erase and the program
timeouts.
Change-Id: Ia86e71505033c52b60ef30092000689fbb547a18
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/902
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The pointer must be non-null here since we returned if allocation failed.
Change-Id: I9b75099ed3b3870c815d1df5760ed1f3fe1d20d6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/866
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Working area pointers shouldn't be re-used, so there's no point in storing
them in the flash bank struct. Make all such pointers local.
Change-Id: Iab65b4e8b475fed7fc72fb8928f54590fa69d260
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/865
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Matthias Blaicher submitted a patch at http://openocd.zylin.com/#/c/891/
to fix the false positive; when no RTOS was detected OpenOCD used the
last RTOS in the list.
While reviewing the code affected by Matthias' patch a rewrite seemed
appropriate, to make the code readable.
Matthias has abandoned his change and this change also fixes the false
positive.
Change-Id: Ic3327ccd036da52ba0a7e21ef93018205e74149c
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/895
Reviewed-by: Matthias Blaicher <matthias@blaicher.com>
Tested-by: jenkins
The new code is almost functionally equivalent to the old.
The function now returns 0 instead of -1 if target->rtos has not yet
been allocated. All call sites only test for success, and in practise
that is also the only thing that matters; if the function successfully
iterated to the next RTOS or not.
Other than that the only difference is that the code is now readable.
Many thanks to Matthias Blaicher for the fix to the iteration error!
Change-Id: I3342826f653b5e46c99ad1f58eec26ff10795c33
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/894
Reviewed-by: Matthias Blaicher <matthias@blaicher.com>
Tested-by: jenkins
The new code is almost functionally equivalent to the old; besides
error handling the only difference is that the code is now readable.
Many thanks to Matthias Blaicher for pointing out an iteration error
in the rtos_try_next() change, which also affected this change.
Change-Id: If38b87439e9de2303b220b3a7e3200ceaa8391da
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/893
Tested-by: jenkins
Reviewed-by: Matthias Blaicher <matthias@blaicher.com>
In FLASHD_ErasePages AT91C_EFC_FCMD_EPA is used to erase sectors.
According to the datasheet FARG[15:2] defines the page from which
the erase will start.This page must be modulo 4, 8, 16 or 32
according to the number of pages to erase. FARG[1:0] defines the
number of pages to be erased. Previously (firstpage << 2) was used
to conform to this, seems it should not be shifted... Changed it
to (firstPage) | erasePages.
Change-Id: I791cc7fc4faf056623ad5a6c7e860315306098a1
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/830
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If configure is executed without --enable-ft2232_ftd2xx then the bus blaster
or presto will fail to build with unresolved external ftd2xx_status_string.
Make sure we run the ftd2xx build test if --enable-usb_blaster_ftd2xx is enabled.
Change-Id: I09d270d6fcd083d77f6785b8969d9acb3dfef11d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/892
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
as well as not being required, as it is already included by jim-nvp.h.
It also makes the doxygen output a bit clearer to read.
Change-Id: Ia2bed7142b4a56b48b1ecf0734e63f860dcd1014
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/859
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
adapter_init expects jtag_get_speed (via ftdi_khz) to return a valid
fallback speed if the adapter does not support rclk. The call was failing
and so was the rest of the adapter init.
The makes the new ftdi driver emulate the old ftdi driver.
Change-Id: Ic7fac7d201241eb181e98f1ba7111f159731f6e0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/839
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch fixes the bug reported here:
http://sourceforge.net/mailarchive/message.php?msg_id=28350157
When using Rlink under Linux, openocd exits with:
"Error: Read of endpoint 2 returned -75, expected 17"
The return value of -75 translates into EOVERFLOW. The cause is a wrong output buffer size argument passed to dtc_run_download().
Change-Id: I5d056705181ab6a6d4355524df06a0ea9c605961
Signed-off-by: Peter Horn <peter.horn@bluewin.ch>
Reviewed-on: http://openocd.zylin.com/862
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Moved common SPI flash driver code (device table,
common commands) into flash/nor/spi.c and spi.h.
Updated flash/nor/stmsmi.c to reflect this refactor.
Change-Id: I141644b0af71d3835f29f06dd15b505a00e5b6ec
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/782
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This driver implements a bitbang jtag interface using gpio lines exported via
sysfs.
The aim of this driver implementation is to use system GPIOs but to avoid the
need for an additional kernel driver.
A config suitable for RaspberryPi is included.
Change-Id: Ib2acf720247a219768d1cbfeebd88057ed2d7b8b
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Reviewed-on: http://openocd.zylin.com/762
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stlink interface currently does not support 16bit read/writes.
Until a fix is included we issue a error that this is unsupported.
Change-Id: I4552cf2bd3b29e90ecc905325b743c08e2b92d67
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/808
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In at91sam3.c for Atmel SAM3 flash support, there are arithmetic errors in the functions sam3_page_read() and sam3_page_write().
Address locations are computed incorrectly due to an extra addition operation. This leads to memory locations being skipped during
flash writes and reads.
Smaller programs are written successfully into flash, with memory gaps, while larger programs of legitimate size fail because the
skipped memory is not utilized and therefore unavailable.
The changes address this condition, and have been tested with an Atmel SAM3X-EK evaluation board.
Change-Id: I9ea3b9ed0130b71cbc32b2294e31a6a2bc71b47a
Signed-off-by: Chuen Chou <zhouquan27@gmail.com>
Reviewed-on: http://openocd.zylin.com/806
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the target does not support SYSRESETREQ we fall back to using VECTRESET.
This however does not reset the peripherals and we issue a warning to the user
to suggest using a reset-init script.
Also suggest that using hardware srst will give them the same functionality
as using SYSRESETREQ.
Change-Id: Ie1781c4b849fed66c52222e6539735537c879fb3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/802
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In function pic32mx_write_block() if the parameter
offset is not a multiple of row size the row offset
(offset % row_size) will be ignored by the flash
controller, shifting the code to the beginning of
the row.
Word programming gets it right.
Change-Id: I134913e3d533688f791bbcb0c6e8983524197f3c
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
So the user can view the current port number these cmds were changed to COMMAND_ANY.
However this means that the user can also attempt to change the port number after init,
even though this is not supported. Issue a warning that this is not supported.
Change-Id: I3d20dcd81277e7d994240a8e314f27672ff760c4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/788
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The last bit of a scan is clocked during TAP movement so it's necessary
for the last field to have at least one bit. Strip trailing empty fields
and make sure the TAP is not affected if there's nothing to scan. Clients
probably shouldn't add empty fields so add a debug message to be able to
track and fix them.
Change-Id: I27552568bc11146570b9b99ed8a1ae81b5fb2c50
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/794
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
When there's no data to scan in or out, we still use the clock data out
command and fill the buffer with zeroes, so make sure the buffer is
checked for available space.
Change-Id: Ia6005c40c81f7fdb89379f1b5023fe383184d210
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/793
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently only the adapter speed is printed, which can be rather misleading
when DEBUG_INFO is disabled, all the user sees is
6000 kHz
instead lets print
adapter speed: 6000 kHz
Change-Id: I8f02a63f47344457e3c3d0a6774157fa18206440
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/797
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add single "scripts" folder to search path for Windows OpenOCD builds
that don't use cygwin
bin/openocd.exe
scripts/interface/dummy.cfg
scripts/target/at91eb40a.cfg
Do some refactoring of current code (thx to Andreas).
Change-Id: Idbb08d1368b06f25da44f4f9ab1511db992b1724
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/785
Tested-by: jenkins
Offset calculation into buffer was wrong and code would read outside buffer
if count was not a multiple of four.
Change-Id: Ied625b10221423d5a5f25d27ce1edd8c2c3eca8a
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/749
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The number if longwords or "sections" (Freescale term) written for a Kinetis
flash write (4, 8, or 16 bytes depending on the part density/granularity) are
now rounded up to ensure there are no truncations when the desired write is
not a multiple of the minimum write size.
Change-Id: I8db40a8769d8ac5393a46cbf4e5ff0df82faf916
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/738
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
For example in a pic32mx220, pic32mx unlock don't work
if adapter_khz is set to 5000 or more.
A short delay after asserting reset fix the problem.
Change-Id: I62e493edfcea585c36c8de77a969cebac7227b96
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/790
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Always scan out all bits, but make sure only the allowed number of bytes
end up in the caller-provided buffer. Discard the rest by adding another
scan field when size < 4.
Rewrite the endianness callback to avoid reading outside allocated memory.
Make it directly usable as a callback without the need for a wrapper. Move
the shared callback to a more suitable home in arm7_9_common.
This fixes the regressions introduced in commits
991ed5a2b6cb90d32e38
and
c3074f377c
Change-Id: Ia8bde8c5a9844e89a1d6c0bc8534cd26f02f8d11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The function wait_for_pracc_rw() fails if Pracc bit is 0.
The variable ejtag_ctrl is loaded with the content of the
control register in the first scan.
In the second scan Pracc bit is scanned out as 0, letting
the proccesor go. The result is unpredictable.
All the strange data corruption when scanning at certain
frequencies, or the strange delays needed when entering
or leaving fasdata area are retated to this bug.
Now the code works at any scan frequency, tested up to 15000Khz
and indepently of processor speed, tested at 31.25Khz and 4/8Mhz.
Change-Id: Iedfd81d06d6af4bc738a521f720e42323025b268
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/769
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
working_area::user has never been used so lets remove it.
Change-Id: I1200311b34248549c1fe30c9f675e6129b7bebee
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/781
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Retest the condition when needed, instead of abusing the common_magic
field as a flag. There are only two options here. Either it's an armv7m or
it's another arm. is_arm(...) will return true even for armv7m, so it's
imperative to check in the right order.
Change-Id: Ic227f19f7babf1b0b0fe075f9a3abc4eabc7d5f1
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By Initialising the param_table we remove the clang warning's.
We are also make sure we are not passing any rogue values to lpc2000_iap_call.
Change-Id: Idb3b0077d1dae5f03dedab1d46d01140fe9ffb10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/777
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reorder to allocate all memory after COMMAND_PARSE_NUMBER call.
This removes a clang warning about un-released memory
Change-Id: I8dbeb664a6467077157015bd879bc0aefc5e8614
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/776
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the flash class was defined as FC_FLEX_RAM then this would always drop
through to the default handler.
This bug was found by clang, so untested.
Change-Id: I2d9fe6415dd216728a145519400f7b9ef1bd3c3a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/773
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Check that the target is valid before calling any target functions.
Change-Id: I538fccc79d5ec89976e14beab02cb20490b299bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/766
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
make distcheck is used to make packages with OpenOCD release, this
command uses information from Makefile.am files to know which files
should be included in the package and which can be left only in
repository. This patch makes a few headers from recent JTAG drivers
and one txt file with info about target tcl config files included in
released packages.
Change-Id: I91202290633a30f53624a8c7d9a0ebf72c40772b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/767
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Jason Moehlman
Spencer Oliver
Salvador Arroyo
Freddie Chopin
Matthias Blaicher
Karl Kurbjun
Peter Horn
Gianluca Renzi
Sergey Borshch
Evan Hunter
Peter Stuge
Edgar Grimberg
Andreas Fritiofson
Paul Fertser
Olivier Schonken
George Harris
Marc Reilly
Chuen Chou
Christopher Kilgour
Martin Nowak
Alexander Osipenko