Could this cause confusion as data sent to write would be flipped
and then if the caller subsequently used the data, e.g. a
compare mismatch might happen?
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The patch below fixes step <address> on mips_m4k.
Spencer Oliver <spen@spen-soft.co.uk>:
The current code is used on all other arch's - is
there a underlying issue with those aswell ?
Add a working area that is preserved between calls to
mips_m4k_bulk_write_memory - this gives us a speed increase
of approx 3kb/sec during flash writes to the pic32mx.
This area is released during a resume/reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Hi everyone,
I figured since I was poking around in the breakpoint code on other arches, I'd
add this change to those arches that don't do it already. This patch propagates
the return code of <arch>_set_breakpoint() up the call stack. This ensures that
the higher layer breakpoint infrastructure is aware that an error ocurred, in
which case the breakpoint is not recorded.
Normally I wouldn't touch code that I can't test, but the code is very
uniform across architectures, and the change is rather benign, so I figured
after careful inspection that it is safe. If the maintainers or others think
this is imprudent, the patch can be dropped.
Also changed the error code to something more appropriate in two cases where
hardware resources are unavailable.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The PIC32MX does not support the ejtag software reset - it is
optional in the ejtag spec.
We perform the equivalent using the microchip specific MTAP cmd's.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The mips_m4k_assert_reset has now been restructured
so the variant ejtag_srst is not required anymore.
The ejtag software reset will be used if the target does not
have srst connected.
Remove ejtag_srst from docs.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- add mips support for target algorithms.
- added handlers for target_checksum_memory and target_blank_check_memory.
- clean up long lines
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
If fastdata access fails, then fallback to default mips_m4k_write_memory
Remove unnecessary fastdata loader verify check
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Uses chaining of command_registration structures to eliminate all
target_type register_callback routines. Exports the command_handler
registration arrays for those target types that are used by others.
Create a generic register_cache_invalidate(), and use it to
replace three all-but-identical core-specific routines:
- armv4_5_invalidate_core_regs()
- armv7m_invalidate_core_regs
- mips32_invalidate_core_regs() too.
Make cache->num_regs be unsigned, avoiding various errors.
Net code shrink and simplification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The quit entry point was not being invoked. Just a source
of confusion at this point. XScale ran 100x reset upon
quit, but that code made no sense, wasn't commented
and never invoke.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Øyvind Harboe
Stefan Mahr
Drasko DRASKOVIC
Andrew Lyon
Spencer Oliver
Mike Dunn
Antonio Borneo
David Claffey
Zachary T Welch
David Brownell
dbrownell
oharboe
duane
zwelch