Driver for DesignWare SPI controller, found on many SoCs (see compatible
list in Linux device tree bindings
Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml). This
implementation only supports MIPS as it was the only one available for the
tests, however, adding support for other architectures should require only
few adjustments. Driver relies on flash/nor/spi.h to find Flash chip info.
Driver internal functions support 24bit addressing mode, but due to
limitations of flash/nor/spi.h, it is not used. The reported writing speed
is about 60kb/s.
Lint, sanitizer and valgrind reported warnings were not related to the
driver.
Change-Id: Id3df5626ab88055f034f74f274823051dedefeb1
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8400
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Most of the work is already done by [1].
Remove few more '_s' suffix and also fix some comment referring to
the old name of the struct.
Link: https://review.openocd.org/c/openocd/+/8340
Change-Id: Ifddc401c3b05e62ece3aa7926af1e78f0c4a671e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8341
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The static analyser 'sparse' complains, while compiling a nor
driver, that the struct flash_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of flash_driver's declaration in driver.h
Fix some incorrect non-const declaration and remove redundant
forward declarations.
Change-Id: I5e41d094307aac4a57dfa9a70496ff3cf180bd92
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7662
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ic7db91fe37d1139d42c99e303b3243b6c8fe3ea2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7067
Tested-by: jenkins
1) The API of "info" callback in "struct flash_driver" has been
improved. Fixed buffers for strings
2) Removed the calls to snprintf() from the flash_driver.info
implementations. Many of them were used in an unsafe manner
(buffer overruns were possible).
Change-Id: I42ab8a8018d01f9af43c5ba49f650c3cb5d31dcb
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6182
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
Fix typos and duplicated words in comments and strings.
Change-Id: I64282c7018462deefeeb8e5f4d0d81942425b3fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5758
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
Use 'unsigned int' and 'bool' instead of 'int' where appropriate.
While at it, fix some coding style issues.
No new Clang analyzer warnings.
Change-Id: I700802c9ee81c3c7ae73108f0f8f06b15a4345f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4929
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Instances of struct flash_driver are never written to at runtime. For a
small amount of memory saving and also robustness (fewer things for
stray pointer writes to hit), mark them const.
Change-Id: Iadbbbc2fac0976d892699200000c5f02856729f3
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4803
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Make flash_driver methods protect() and protect_check()
optional.
Remove dummy definitions of these methods from the drivers
which do not implement protection handling.
Some drivers did not define protect method. It raised segfault
before this change and now it is handled properly.
Lot of drivers returned ERROR_OK from dummy protect()
- now flash_driver_protect() returns an error if not handled by the driver.
Change-Id: I2d4a0da316bf03c6379791b1b1c6198fbf22e66c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4765
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
some chips unprotect more than the range asked for. The
protect fn, must unprotect/protect minimally the range given.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Move the bulk of the flash.h file into flash/nor/core.h, leaving an
empty husk that will be removed in the next patch.
The NOR driver structure is an implementation detail, so move it into
its own private header file <flash/nor/driver.h> along with helper
declaration for finding them by name.
Sergey Matsievskiy
Antonio Borneo
Steven Chang
iosabi
Jan Matyas
Andreas Bolsch
Marc Schink
Christopher Head
Tomas Vanek
Marc Schink
Andreas Fritiofson
Spencer Oliver
Christopher Kilgour
Øyvind Harboe
Zachary T Welch