Commit Graph

3 Commits

Author SHA1 Message Date
Matthias Welwarsky 2231da8ec4 target: restructure dap support
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
  instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
  longer references the dap, daps are now independently
  created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
  power cycle)
- update documentation
- update target files

Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 09:58:21 +01:00
Andreas Färber 0c8ec7c826 Fix spelling of ARM Cortex
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.

Cf. http://www.arm.com/products/processors/index.php

Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.

Found via:

  git grep -i "Cortex "
  git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
  git grep -i "CortexM"

Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-05-20 21:38:03 +01:00
Jacob Palsson 45a86f8e2a tcl/target: add CC2538 and CC26xx target files (with cJTAG procedure)
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.

These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.

The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.

Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2015-02-11 15:22:40 +00:00