we should have caught them all - hopefully.
Change-Id: I35435317fccaf5ad0216244d69f76db6857bb582
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/381
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
On wrong parameters a error is signalized to the calling function.
Change-Id: I484443fdb39938e20382edc9246d5ec546a5c960
Signed-off-by: Mathias K <kesmtp@freenet.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/282
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
Could this cause confusion as data sent to write would be flipped
and then if the caller subsequently used the data, e.g. a
compare mismatch might happen?
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The patch below fixes step <address> on mips_m4k.
Spencer Oliver <spen@spen-soft.co.uk>:
The current code is used on all other arch's - is
there a underlying issue with those aswell ?
Add a working area that is preserved between calls to
mips_m4k_bulk_write_memory - this gives us a speed increase
of approx 3kb/sec during flash writes to the pic32mx.
This area is released during a resume/reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Hi everyone,
I figured since I was poking around in the breakpoint code on other arches, I'd
add this change to those arches that don't do it already. This patch propagates
the return code of <arch>_set_breakpoint() up the call stack. This ensures that
the higher layer breakpoint infrastructure is aware that an error ocurred, in
which case the breakpoint is not recorded.
Normally I wouldn't touch code that I can't test, but the code is very
uniform across architectures, and the change is rather benign, so I figured
after careful inspection that it is safe. If the maintainers or others think
this is imprudent, the patch can be dropped.
Also changed the error code to something more appropriate in two cases where
hardware resources are unavailable.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The PIC32MX does not support the ejtag software reset - it is
optional in the ejtag spec.
We perform the equivalent using the microchip specific MTAP cmd's.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The mips_m4k_assert_reset has now been restructured
so the variant ejtag_srst is not required anymore.
The ejtag software reset will be used if the target does not
have srst connected.
Remove ejtag_srst from docs.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- add mips support for target algorithms.
- added handlers for target_checksum_memory and target_blank_check_memory.
- clean up long lines
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
If fastdata access fails, then fallback to default mips_m4k_write_memory
Remove unnecessary fastdata loader verify check
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Uses chaining of command_registration structures to eliminate all
target_type register_callback routines. Exports the command_handler
registration arrays for those target types that are used by others.
Create a generic register_cache_invalidate(), and use it to
replace three all-but-identical core-specific routines:
- armv4_5_invalidate_core_regs()
- armv7m_invalidate_core_regs
- mips32_invalidate_core_regs() too.
Make cache->num_regs be unsigned, avoiding various errors.
Net code shrink and simplification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Spencer Oliver
Mathias K
Øyvind Harboe
Stefan Mahr
Drasko DRASKOVIC
Andrew Lyon
Spencer Oliver
Mike Dunn
Antonio Borneo
David Claffey
Zachary T Welch
David Brownell