Lets be consistent and use strndup to allocate the debug buffer.
Change-Id: I535ad270ebfeae6e09d28372ab3749c822971223
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/245
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Compile error is encountered when _DEBUG_GDB_IO_ is set,
due to duplicate variables.
Fixed by renaming the variable.
Change-Id: I729c06e317fdb899142c9ceaf543b7f580088807
Signed-off-by: James Zhao <jamzhao@gmail.com>
Reviewed-on: http://openocd.zylin.com/243
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The calculation for reg_packet_size in gdb_get_registers_packet() could
generate a wrong result in the case of multiple registers whose size is
not a multiple of 8.
The current calculation sums the sizes for all registers then rounds the result
up to the next multiple of 8.
Instead it should round each register size up individually and sum the results for all registers.
Change-Id: Idfb5e5eeee0e69a6889dbe9769c0bf17feacb63b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
gdb_memory_map() correctly calculates the target specific number of flash banks, but then uses the total number (all targets) instead of the target specific number to construct its GDB response, causing a crash.
Change-Id: I3f8639b3e90303a59753ebe140ce4fff96fd5db0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/199
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The fix is inline with the Linux coding style that forbids
assignment in if condition
Change-Id: I0b9d0b419d9c8b7a8c755e048d5faf72d1658ba2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/87
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
by immediately polling again when we have received a message from
the target instead of waiting 100ms, we can hope for much better
performance. More than 100x? :-)
Change-Id: Ieaf0c6c8b6e5addc482895670ffbf9a743e07a29
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/27
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
- works on Cortex-M3 with ThreadX and FreeRTOS
Compared to original patch a few nits were fixed:
- remove stricmp usage
- unsigned compare fix
- printf formatting fixes
- fixed a bug with overrunning a memory buffer allocated with malloc.
Fix a bunch of typos.
Most are in code comments, so nothing should break. UNKOWN_COMMAND and
CMD_UNKOWN are not used elsewhere, so correcting the spelling should
also not break anything.
the error values is not part of the interface to the user,
so they should never be printed in LOG_INFO or LOG_USER.
Printing them in LOG_DEBUG() rarely makes much sense but
is OK.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this never panned out and there are enough mistakes in
the code that probably nobody used this.
Use the tcl server and implement a standalone http
app instead works fine.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
gdb connect can fail when the flash has not been probed.
During gdb connect, the flash layout is reported, but this
can not be automatically detected for a target that is
powered up and OpenOCD supports connecting to gdb server
even if the target is powered down.
The solution is to turn of the gdb_memory_map feature.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
commit 50d5441e2a caused
native windows build to fail.
Firstly this patch fixes the build issue, but it also disables support
for named pipes under Windows. Windows does not support posix named
pipes.
A cross-platfom access layer will need creating before support can be
enabled again.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
there was special support to support pressing 'x' to quit
openocd. ctrl-c is sufficient. The main server loop is already
complicated enough.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by using ctrl-z instead of line end, multi-line tcl scripts
can be handled.
Testing: send ctrl-z a couple of times to make telnet enter the
mode where it sends ctrl-z unencoded.
Programs that talk to the tcl_server can send ctrl-z to
indicate end of tcl-let to be executed without having
to worry about telnet protocols.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
c->sin.sin_port does not contain a valid port number so just use
service->port as this is always correct.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
No segmentationfault when sending commands to tcl-server.
modified: src/server/server.c
modified: src/server/tcl_server.c
modified: src/server/tcl_server.h
by ack'ing memory writes immediately and reporting either
at next memory write or stepi/continue time. GDB will then
send off a new packet that is ready by the time the previous
packet has been written to target memory.
On faster adapters this can be as much as 10% improvement.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Sometimes we saw two strange blank spaces at the beginning
of the telnet lines.
progress
ogress
>
This patch fixes this problem:
progress
progress
>
The code changes are *reasonably* clean, but perhaps it could be
made a bit more elegant, but I didn't want to change things after
I finished diagnosis/testing & submitting the patch.
The problem was that logging can send the text and the newline
separately in two different requests and the telnet code would
incorrectly remove the prompt from the end of a line.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Rather than issuing a halt and then stepi/resume, just
wait for target to halt.
Issue a sterner warning via gdb console that any gdb
register changes will be ignored in this case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Report each region of same-size sectors separately, instead of
incorrectly reporting that every sector has the same size.
This is a longstanding bug on NOR flash chips with non-uniform
sector sizes. It was largely hidden by other bugs in flash
handling. When some of those were recently fixed, this one was
exposed as a regression on str710.
[oyvind.harboe@zylin.com: update the loop to behave on str7 ]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Put the memory map logic into its own subroutine.
This will make it a bit easier to package bugfixes,
and simplifies the query packet handling.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make most methods static; net minor object code shrink.
Likewise various data symbols; no net change.
Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The gdb_port command can be invoked during normal execution
to report the port used for gdb, whereas it was listed as
CONFIG stage only, which caused an error when excuting
it to return the reported error.
Also in line with the grander goal of making more commands
available during all "modes" (perhaps retiring config mode),
there is no particular reason to limit gdb_port to the
config stage.
Regression was introduced in:
b3bf1d12b2 aka
v0.4.0-rc1-32-gb3bf1d1
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove useless space/tab at end of lines.
Remove spaces in indentation and replace with tab.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
By exhausting data on input, the performance will be more
consistent + the code more clearly distinguishes between
polling and processing. A test showed gdb packet load
performance go from ~1550kByte/s to 1650kBytes/s + being
more stable.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This fixes the issue under native win32 of the socket interface not being
enabled (via WSAStartup) before init is called from a script.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Use a separate variable for iterating GDB service port numbers than
the one set by the user. Restores the behavior of returning the
original port number and only incrementing the port used on success.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "server.h"
the following form should be used.
#include <server/server.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "flash.h"
the following form should be used.
#include <flash/flash.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "target_request.h"
the following form should be used.
#include <target/target_request.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "target.h"
the following form should be used.
#include <target/target.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "register.h"
the following form should be used.
#include <target/register.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "image.h"
the following form should be used.
#include <target/image.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "breakpoints.h"
the following form should be used.
#include <target/breakpoints.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "jtag.h"
the following form should be used.
#include <jtag/jtag.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "log.h"
the following form should be used.
#include <helper/log.h>
The exception is from .c files in the same directory.
The new stubs for httpd and ioutil gave errors like:
ioutil_stubs.c: In function ‘ioutil_init’:
ioutil_stubs.c:27: error: implicit declaration of function ‘LOG_DEBUG’
ioutil_stubs.c:28: error: ‘ERROR_OK’ undeclared (first use in this function)
ioutil_stubs.c:28: error: (Each undeclared identifier is reported only once
ioutil_stubs.c:28: error: for each function it appears in.)
Fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add httpd_stubs.c to provide no-op implementations of httpd_start()
and httpd_stop().
Allows these routines to be called unconditionally and ensures the
libocdserver ABI remains unchanged regardless of whether this feature
was built-in or not.
Prints a DEBUG message when the stub implementation is included.
Finish removing references to the 'interp' global variable from the
command module, encapsulating all reference via command_context.
Eliminates use of the global entirely, so it can be removed. Hurrah!
Moves the telnet and TCL server startup to server_init(), moving their
respective command registration in to server_register_commands().
Adds proper error checking for these particular startup processes.
Moves the core server startup to openocd_main(), improving related error
checking and preparing to defer 'init'.
Rework gdb_init to create flexible APIs (gdb_target_add_{one,all}) and
static helper (gdb_target_start) for starting GDB services. Eliminates
duplicated code and provides general mechanisms for adding GDB services.
The 'init' command is updated to call the new API, and later patches can
decouple its policy of adding all targets therein.
Provides the new capability to use both piped and TCP servers when
multiple targets are defined. The first target fills the pipe, and
others will be started on TCP ports (unless disabled, i.e. gdb_port=0).
Several of the sites now using target_type_name() really
ought to be using an instance-specific name. Create a
function called target_name(), accessing the instance's
own (command) name.
Use it in several places that really should be displaying
instance-specific names. Also in several places which
were already doing so, but which had no wrapper to call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There are two names that may matter on a per-target basis.
One is a per-instance name (for example, "at91sam7s.cpu").
The other is the name of its type (for example, "arm7tdmi"),
which is shared among multiple targets.
Currently target_get_name() returns the type name, which is
misleading and is rarely appropriate for target diagnostics.
Rename that as target_type_name().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Updates httpd_start() to use register_commands() for 'readform' and
'writeform' commands. Adds server/httpd.h to export the new signatures
for this function (and httpd_stop), which allows removing the obsoleted
declarations inside openocd.c.
Updates all command parsing of simple "enable" and "disable" arguments.
A few case in the tree use a tri-state or extended arguments, which
cannot use this simple macro.
Simlifies the xscale icache/dcache command handler logic.
Moves definitions for each layer into their own file, eliminating
layering violations in the built-in TCL code. Updates src/Makefile.am
rules to include all files in the final startup.tcl input file, and
others Makefile.am rules to distribute the new files in our packages.
No need to indirect from registered integers to pointers.
Just stash the pointers directly in the register struct,
and don't even bother registering.
This is a small code shrink, speeds register access just
a smidgeon, and gets rid of another rude exit() path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Create src/openocd.h to hold declarations previously made internally
by src/main.c and src/server/server.c. This ensures all functions
are verified to be in-sync at compile time (rather than at link),
making it easier to track down bugs.
By using CALL_COMMAND_HANDLER, parameters can be reordered, added, or
even removed in inherited signatures, without requiring revisiting
all of the various call sites.
Added gdb_sync feature that allows GDB to sync up to target state.
Issue "monitor gdb_sync" and the next stepi, will return immediately
with updated register values to GDB.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2754 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Øyvind Harboe
Spencer Oliver
James Zhao
Philip Nye
Antonio Borneo
Jie Zhang
Freddie Chopin
Michel Jaouen
Broadcom Corporation (Evan Hunter)
Uwe Hermann
Spencer Oliver
sb-sf
Jun Ma
Matthias Bode
David Brownell
Zachary T Welch
oharboe
dbrownell
duane
ntfreak
zwelch