Reintroduce checkpatch problem, because now we can handle them better.
Change-Id: Ib81b9910433ae1a240630b898edb19da8d2d5d83
Signed-off-by: Tim Newsome <tim@sifive.com>
The static analyser 'sparse' complains, while compiling a nor
driver, that the struct flash_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of flash_driver's declaration in driver.h
Fix some incorrect non-const declaration and remove redundant
forward declarations.
Change-Id: I5e41d094307aac4a57dfa9a70496ff3cf180bd92
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7662
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a nand
driver, that the struct nand_flash_controller is declared in the
file as non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of nand_flash_controller's declaration in driver.h
While there, drop the unused/commented boundary scan controller.
Change-Id: I7dc32cef55be13ba537abe0f4c47b135d837126c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7661
Tested-by: jenkins
Add static type to symbols that are not used elsewhere.
Detected through 'sparse' tool.
Change-Id: I2bdac5d2b06a6dbed5c27bfdb1cf36eee90ad823
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7594
Tested-by: jenkins
On 32 bit hosts, gcc should consider constants without suffix as
32 bits values. Adding a cast to convert it to 64 bits should not
be enough.
Use the suffix 'ULL' to guarantee it is a 64 bit.
Detected through 'sparse' tool.
Change-Id: If6be35bd3cbbc7c3a83e0da1407e611f07ff6e06
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7593
Tested-by: jenkins
If the file read abnormally, need to close it which was opened before.
Signed-off-by: panciyan <panciyan@eswincomputing.com>
Change-Id: I6142f154741dcd38088b7add2793219ee4dd2ae9
Reviewed-on: https://review.openocd.org/c/openocd/+/7546
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'flash list' as OpenOCD command.
While there:
- format in a human readable way the output dictionary list, while
preserving the structure of its TCL data;
- add the mandatory 'usage' field.
Change-Id: I1ee69870d3ab3c1cfc46cd2b8ec03de6b2300bd6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7486
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
All DIDs are taken from "SAM R34/R35 Errata Sheet" (DS80000834A).
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: Ie35f58e61bb02919c0676c91938c90192481d995
Reviewed-on: https://review.openocd.org/c/openocd/+/7521
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to the datasheets these MCUs have 40Kb RAM.
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: I52b8a0c86035bccd6f3c1a478bb2e558bca4ae86
Reviewed-on: https://review.openocd.org/c/openocd/+/7520
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This probably crept in when merging in upstream in the past.
Change-Id: Iccce4515b6b5d4a90773f6d432754b065fb240bb
Signed-off-by: Tim Newsome <tim@sifive.com>
A bunch of new SPI flash (Adesto, Cypress, XTX Tech, mainly octal)
IDs and SPI FRAM (Infineon) IDs added. Backward compatible change
of ID interpretation: The previously unused 4th byte now acts
as continuation code (0x7F) count for manufacturer id, cf.
JEDEC JEP106BC. Currently this affects only some recent octal flash
and FRAM devices, which are only supported by stmqspi and cmspi
flash drivers.
Change-Id: Ibdcac81a84c636dc68439add4461b959df429bca
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6929
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Polling the target makes no harm during PSoC 4 flash write in the current
OpenOCD code. Don't mask it.
Change-Id: I6625ded0162ee3a96b92188844d0d2d6c30101c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7162
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Simply move numicro M0 flash write assembly to contrib/loaders. Also,
modify corresponding Makefile and generated numicro_m0.inc.
To make the path more general, this patch rename the path
"contrib/loaders/flash/numicro_m4" to "contrib/loaders/flash/numicro" as
well.
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9adea24c2b3c97319a9b015cf50257f3d131dc26
Reviewed-on: https://review.openocd.org/c/openocd/+/7346
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is picked from the flash part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support flashing Nuvoton's Cortex-M4 chips: M541 & NUC442/472 series.
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9dc69eccb851df14c1b0ce2f619d7b3da0aa92aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7329
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is picked from the flash part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
It reorders Nuvoton MCU part list and spreads out the way to define the
banks' base address & size of the parts.
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I1f21f54dfdf53e5b8ea04d803347d1dbc8c321a0
Reviewed-on: https://review.openocd.org/c/openocd/+/7339
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Do not read ID from SPI flash and suppress autodetection
if non-zero flash bank size is configured.
Change-Id: Idcf9ee6ca17f9fa89964a60da7bf11e47b4af5e7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7241
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The HiFive Inventor uses this flash chip, so adding it will allow for
openocd to be used to program it. These values were taken from the
chip's documentation.
Signed-off-by: Fawaz Tirmizi <fawaz@rivosinc.com>
Change-Id: I15c9d35f99d4500f73134cdc2d1b9ab6279b491c
Reviewed-on: https://review.openocd.org/c/openocd/+/7135
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Flashing a SAMD21J17D was failing during NVM erase. The samd21
datasheet specifies that one cause of error conditions is executing an
NVM command while the previous command is still running. The solution
is to wait for INTFLAG.READY after a command is issued.
SAMD21J17A was not exhibiting this problem. Perhaps the later silicon
revision has slower NVM erase times.
Signed-off-by: Dan Stahlke <dan@stahlke.org>
Change-Id: I19745dae4d3fc6e3a7611dcac628e067cb41e0f0
Reviewed-on: https://review.openocd.org/c/openocd/+/7391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The variable retval is assigned a value that is never used.
Scan-build reports:
Although the value stored to 'retval' is used in the
enclosing expression, the value is never actually read
from 'retval'.
Drop the dead assignment.
Change-Id: I11588dee748a55d52aa7f35bc1967b7df55af7fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7379
Tested-by: jenkins
target_run_flash_async_algorithm expects the source_buffer to have
at least 2 words reserved for read and write pointers in addition to the
FIFO buffer. If the size of the data to be flashed is <= 8 bytes then
the flash function will fail with "corrupted fifo read pointer" error.
Ensure the allocated buffer is big enough to hold both FIFO buffer and
read/write pointers.
Change-Id: I09c22eaac517b8cfea8e0b463f5deb6b98afd267
Signed-off-by: Simon Smiganovski <simon.smiganovski@fruitcore.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7342
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable retval is assigned a value that is never used, as it
is reassigned few lines below.
Drop the dead assignment.
Change-Id: Id4e9134408fab3e04936d36e95724bf8d3ab55aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7304
Tested-by: jenkins
ST-Link v2 dongles can be used with many cortex-m parts, but they have
one limitation -- they can only perform 8-bit and 32-bit writes to the
target. 16-bit writes are done using a pair of 8-bit writes. While not
usually an issue, in the case of the at91samd flash driver, the 16-bit
'command' register must have both halves written in the same
operation.
Fortunately, this register has two pad bytes above it in the address
space, making it safe to always access with 32-bit operations.
Change-Id: I44b0db9406982a8db5818c0533d3101618741db2
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7234
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The num_reg_params parameter of target_run_algorithm() was not
updated when setting "sp" was introduced. Therefore "sp" as the last
register parameter was not passed to a target algo.
Introduce a new helper variable with correct count of register parameters
and use it everywhere needed.
Change-Id: I934a71380783d98917167f1569145808ef23540f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7225
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Change-Id: Idf3bce842b4507c1f12692b5fbcd6730637de9db
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7216
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Flash read_id/erase/write operation on running target failed
in target_run_algorithm() anyway. It generated lot of error messages.
Check the target state and bail out early if target is running.
Change-Id: I903f5f38c8e61016e5002b235e5f07803bd2ec4e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
SPI flash erase often takes longer than the fixed timeout 3 seconds.
Introduce a configurable timeout_ms parameter to rp2040_call_rom_func().
Compute the erase timeout from the number of blocks to be erased.
While on it make the timeouts shorter for connect flash, flush cache and
enter/exit xip (1 second is enough).
Change-Id: I552bfa317ee17064de3a54ec2f0c63e84ba87222
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7214
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The size of the flash write buffer should be rounded
down to the multiply of flash page size.
Using write chunks of unadjusted size results in write of chunks
unaligned to flash pages.
Change-Id: If7931362ee193dff4dc2df7ec78f13530658cf08
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7187
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tim Newsome
Antonio Borneo
panciyan
Andrew Lalaev
Daniel Anselmi
Andreas Bolsch
Marc Schink
Daniel Serpell
Tomas Vanek
Jian-Hong Pan
Zale Yu
Tarek BOCHKATI
Fawaz Tirmizi
Kyle Schwarz
Dan Stahlke
Simon Smiganovski
Keith Packard