It had a very little bit of content; move that to the more extensive
chapter on config file guidelines, and give more current "ls" output
to show the available library code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2820 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- revert to previous default: don't talk JTAG during SRST
- add "srst_nogates" flag, the converse of "srst_gates_jtag"
- with no args, display the current configuration
And update the User's Guide text with bullet lists to be a bit more clear.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2818 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- The guess-rev.sh script is now a tweaked version of "setlocalversion" as
seen in Linux, U-Boot, and various other projects. When it finds source
control support (git, hg, svn) it uses IDs from there. Else (specific
to this project) it reports itself as "-snapshot", e.g. from gitweb.
I verified this new "guess-rev.sh" script runs under Cygwin.
- Also update the generic version strings to be like "0.3.0-dev" (during
development) instead of the very long "0.3.0-in-development". These also
show up in the PDF docs. For better tracking, we might eventually change
these strings to include the version IDs too.
- Change the startup banner version strings so they include the guess-rev
output. Development and release versions with GIT will be like
Open On-Chip Debugger 0.3.0-dev-00282-g7191a4f-dirty (2009-10-05-20:57)
Open On-Chip Debugger 0.3.0 (2009-10-05-20:57)
instead of the previous SVN-specific (even when using git-svn!)
Open On-Chip Debugger 0.3.0-in-development (2009-10-05-01:39) svn:exported
Open On-Chip Debugger 0.3.0 (2009-10-05-01:39) Release
git-svn-id: svn://svn.berlios.de/openocd/trunk@2809 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Bugfix the error message so it shows the disliked value, and add
a debug message showing each TAP's IR capture value, all N bits.
This just changes diagnostics ... it still ignores the parameters
given to us at TAP declaration time.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2801 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The model is that this fires after scanchain verification, when it's
safe to call "jtag tapenable $TAPNAME". So it will fire as part of
non-error paths of "init" and "reset" command processing. However it
will *NOT* trigger during "jtag_reset" processing, which skips all
scan chain verification, or after verification errors.
ALSO:
- switch DaVinci chips to use this new mechanism
- log TAP activation/deactivation, since their IDCODEs aren't verified
- unify "enum jtag_event" scripted event notifications
- remove duplicative JTAG_TAP_EVENT_POST_RESET
git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- don't needlessly export this function
- handle "case 0" debug method-of-entry better (silent by default)
The "case 0" is a valid debug entry mode so it doesn't deserve the
warning int now gets. But it probably means that OpenOCD confused
itself somehow; or that it confused the ARM9EJS target.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2799 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- ETB
* report _actual_ hardware status, not just expected status
* add a missing diagnostic on a potential ETB setup error
* prefix any diagnostics with "ETB"
- ETM
* make "etm status" show ETM hardware status too, instead of
just traceport status (which previously was fake, sigh)
- Docs
* flesh out "etm tracemode" docs a bit
* clarify "etm status" ... previously it was traceport status
* explain "etm trigger_percent" as a *traceport* option
ETM+ETB tracing still isn't behaving, but now I can see that part of
the reason is that the ETB turns itself off almost immediately after
being enabled, and before collecting any data.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2790 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Improve and clarify the wording of the introduction.
- Add section on version taggging.
- Some other minor corrections.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2788 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The release process itself does not use this support yet, but it allows
packagers to automate the process of managing their own tags, if they
patch the source code before releasing binaries. The release processes
should be revised to incorporate this feature to support -rc packages.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2786 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- The NEWS step failed due to an empty commit comment.
- The final release step would have failed, because the steps to switch
from the secure to insecure repository (and back again) require both
switch and a URL relocation steps
git-svn-id: svn://svn.berlios.de/openocd/trunk@2782 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Don't issue needless JTAG resets ... only do them after
errors. Normal exit now leaves every TAP in BYPASS.
- Fix an unlikely memory leak on one fault path.
- Remove the oddball limitation that invalid capture LSBs
trigger errors only for TAPs that support IDCODE.
Re the JTAG reset: there are too many of them, and they can
(and do!) change system state. So the needless ones should
get removed. This one was especially pointless.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2777 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Commands were supposed to have been "arm11 memwrite ..."
not "memwrite ..."
- Get rid of obfuscatory macros
- Re-alphabetize
- Add docs for "arm11 vcr"
git-svn-id: svn://svn.berlios.de/openocd/trunk@2776 b42882b7-edfa-0310-969c-e2dbd0fdcd60
dbrownell
David Brownell
oharboe
mlu
zwelch