Highlight that the "-expected-id" probably comes from vendor
documentation, and that it *should* be used where possible.
Don't use ircapture/irmask in examples, to help discourage
use of those params when they're not required. Explain a
bit better about why/when those params get used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fail watchpoint_add() if it's the same address but the
parameters are different ... don't just assume having
the same address means the same watchpoint! (Note that
overlapping watchpoints aren't detected...)
Handle unrecognized return codes more sanely; don't exit()!
And describe command params right.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Expose most DWT registers via Tcl; there are a few more, but
those are mostly for profiling along with the ITM. Having
this set available enables operations which aren't possible
with just the standard watchpoint operations.
The cycle counter may be interesting. Turn it on after reset
by setting the LSB of the dwt_ctrl register, and it counts
CPU clocks. You can program the comparator 0 watchpoint to
trigger on a given cycle count, rather than a data address.
Likewise, comparator 1 may be able to match data values given
address matches from one or two other comparators. (Not all
hardware supports this capability though; try it. That is
something the standard watchpoint methods should eventually
handle, for the single address case.)
Minor cleanup: remove needless functional indirection for
exposing the v7m architctural registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There's no reason to read which interrupts are enabled from
the NVIC; that state isn't used. Plus, it's highly dynamic
since firmware can change it at any time; remove the support
for those state records.
Remove duplicate definition of DWT_CTRL address; shrink a line.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix the watchpoint error checks, and do them in add(), not later
in set() when it's mostly too late. Support the full range of
watchpoint sizes (1 to 32K bytes each), and check alignments.
Minor cleanup of DWT access: shrink lines, use "+" for address
calculations, comment a few issues. Add debug message reporting
DWT capabilities, matching the message for FBP, and some minor
code and spec review comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add Doxygen for the exported ARMv7-M interfaces.
Make the non-exported stuff static. Remove functions and
data which are now observably unused.
Add comment about a small speedup that the run_algorithm()
logic could use. Shrink a few too-long lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
improve default target->read/write_phys_memory, produce
more sensible error messages if the mmu interface
functions have not been implemented yet vs. will
not be implemented(e.g. cortex m3).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The quit entry point was not being invoked. Just a source
of confusion at this point. XScale ran 100x reset upon
quit, but that code made no sense, wasn't commented
and never invoke.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Previous patch somehow made GCC lose some of its cookies;
work around, zero-init that struct.
Clean up code from the previous patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Config for Intel's "Lubbock" PXA255 development board. Even more
so than the PXA255 itself, this is obsolete. AFAIK this was the
first generally available development platform for PXA255. Intel
stopped providing these after other devel boards became available.
One interesting thing about this board from the OpenOCD perspective
is probably its flash configuration. Each bank is 32 bits wide,
built from two 16-bit StrataFlash chips wired in parallel. This
doubles throughput ... it reads/writes 32 bits in the time a single
chip takes to write just 16 bits.
This conf mostly works, given XScale bugfixes, but has some issues
(notably: no access to the on-board SDRAM) flagged by FIXMEs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We currently do something unusual: version codes in config.in get
updated after the release, which means that "git describe" won't
match up to development version labels. Comment that trouble spot.
We can fix this by switching away from the major/minor/micro type
release numbering, as various other projects have done. The major
numbers basically don't tend to change, and doing a good job with
micro versions is so annoying that they rarely change either.
Contrast releases to git snapshot tarballs. Mention that
releases have some quality-improvement focus, with special
non-"dev" version IDs. Explain more about version IDs,
using "openocd -v" to see them, etc;
Make release milestone info be less specific about timing,
and presume we have both a merge window and an RC stage.
Rework the release process information to match reality a
bit more closely. Reference the version.sh script (in one
place the wrong script was referenced). Bugfix branches
get special treatment, while non-bugfix releases are more
or less what *defines* being the mainline branch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "source" command isn't accepted by ASH; easy to fix.
Failures with "-e" are harder to fix. Remove the "-e"
(for now) and force bash, for safety.
Un-obfuscate the release steps, by using names instead
of numbers. Comment the version-number manipulation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Various include files require some other include files
to be included first. Copied solution from net/if.h.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
To support breakpoints, flush data cache line and invalidate
instruction cache when 4 and 2 byte words are written.
The previous code was trying to write directly to the physical
memory, which was buggy and had a number of other situations
that were not handled.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Fixed bug: if virtual address for working memory was not specified
and MMU was enabled, then address 0 would be used.
Require working address to be specified for both MMU enabled
and disabled case.
For some completely inexplicable reason this fixes the regression
in svn 2646 for flash write in arm926ejs target. The logs showed
that MMU was disabled in the case below:
https://lists.berlios.de/pipermail/openocd-development/2009-November/011882.html
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This change is necessary to debug AT91SAM9260 on my PC with a
FT2232H dongle.
Signed-off-by: Dimitar Dimitrov <dinuxbg@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Mention the autoprobing as a tool that may be useful when
figuring out how to set up; and add a section showing how
to use that mechanism (with an example).
Strengthen the differences between config and run stage
descriptions; add a section for the latter.
Mention Dragonite.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For some reason, all the interals are documented by default.
This is wrong for two basic reasons:
- We need to focus on public interfaces, since those are
the architectural interfaces and relationships.
- Since virtually nothing has doxygen support yet, this
maximizes the noise, and minimizes the usefulness of
doxygen output.
So don't expose so much by default.
Gets rid of the runtime warning "stm32.bs: nonstandard IR mask"
[dbrownell@users.sourceforge.net: line lengths, note issue, section ref]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Just use the array of names we're given, ignoring indices.
The "reserved means don't use" patch missed that change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This gets rid of runtime warnings from the use of numbers.
STM32 and LPC2103 were tested. Other LPC updates are the
same, and so are safe. The CFI updates match other tested
changes now in the tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There were a few more changes worth mentioning, including support
for more JTAG adapters, boundary scan improvements, another NAND
driver, and the Win64 stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I'm suspecting this code can never have worked, since the
original commit (svn #335) in early 2008.
Fix is just copy/paste from another (working) function.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add interface configs for two new high speed JTAG
adapters from Olimex. They need some other speed
related tweaks to work well at high speed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Implement XSVF support for detailed state path transitions,
by collecting sequences of XSTATE transitions into paths
and then calling pathmove().
It seems that the Xilinx tools want to force state-by-state
transitions instead of relying on the standardized SVF paths.
Like maybe there are XSVF tools not implementing SVF paths,
which are all that we support using svf_statemove().
So from IRPAUSE, instead of just issuing "XSTATE DRPAUSE"
they will issue XSTATES for each intermediate state: first
IREXIT2, then IRUPDATE, DRSELECT, DRCAPTURE, DREXIT1, and
finally DRPAUSE. This works now.
Handling of paths that go *through* reset is a trifle dodgey,
but it should be safe.
Tested-by: Wookey <wookey@wookware.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Unneeded exports cause confusion about the module interfaces.
Make most functions static, and fix some line-too-long issues.
Delete some now-obviously-unused code.
The forward decls are just code clutter; move their references
later, after the normal declarations. (Or vice versa.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Unneeded exports cause confusion about the module interfaces.
Only the Feroceon code builds on this, so only routines it
reuses should be public.. Make most remaining functions
static, and fix some of the line-too-long issues.
The forward decls are just code clutter; move their references
later, after the normal declarations. Turns out we don't need
even one forward declaration in this file.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Hex parser uses a fixed number of sections. When the
number of sections in the file is greater than that, the
stack get corrupted and a CHECKSUM ERROR is detected
which is very confusing.
This checks the number of sections read, and increases
IMAGE_MAX_SECTIONS so it works on my file.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Øyvind Harboe
David Brownell
Krzysztof Kajstura
Dimitar Dimitrov
Freddie Chopin
Spencer Oliver
Michael Roth
Zachary T Welch
Franck HÉRÉSON