It has been seen on some stm32 targets that the flash size register that
is probed by the driver may contain an invalid size.
This change enables the user to override the probed value.
Change-Id: I09359e59a96f9133d3d939670957d32a830a944e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1132
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
This makes sure we are using privileged mode when executing any loaders.
Change-Id: I18bf32ec92e1c76a66ab25e3712652bc3650b332
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1108
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
To simplify things change over to using the generic core_mode struct rather
than maintaining a armv7m specific one.
Change-Id: Ibf32b785d896fef4f33307fabe0d8eb266f7086f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/966
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updated as per ST RM0033 rev 5
Change-Id: I627fdab69b440b75b8e4f7c474216538fa5273a4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1001
Tested-by: jenkins
Other than a larger memory layout these new devices also have an extra
MER1 bit to perform the mass erase.
Change-Id: I7110a05bac95c1707160d1f5622181664291eb4a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/985
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Working area pointers shouldn't be re-used, so there's no point in storing
them in the flash bank struct. Make all such pointers local.
Change-Id: Iab65b4e8b475fed7fc72fb8928f54590fa69d260
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/865
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove a lot of the repetitive code in stm32f1x flash probe by converting
the large if-selector to a switch, moving the common checks outside it and
concentrating the failure handling to a single point.
Do the same with stm32f2x and stm32lx for consistency.
Change-Id: Ic0ecfb1533c49f5d2108cda5fd20c8372d7c71ef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/746
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some variants read 0 for the flash size register, rather than
failing lets assume we have max flash fitted.
Change-Id: Ie1fb4e73606f49268a6fd5921c3aef75bc4790d3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/744
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Use default_flash_blank_check, this will use the much faster
blank_check_memory handler if supported - 15x quicker on stm32f4.
Otherwise it will fall back to using the slower default_flash_mem_blank_check.
Change-Id: Ia231b3e95468c9e92594dbdbe1fa2d69e1506fc3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/632
Tested-by: jenkins
This enable the stm32f2x flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 1048576 bytes from file stm32f4x.bin in 30.453804s (33.625 KiB/s)
after - wrote 1048576 bytes from file stm32f4x.bin in 23.679497s (43.244 KiB/s)
This also fixes a bug that was in the old flash loader.
The old loader waited while bit16 of the status reg was 0, the new
loader waits until this bit is 0 as stated in the flash spec.
Bizarrely this bug did not effect programming on any tested parts.
Change-Id: I3efc94d42cbe81283673a8f4203700638080af6e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/460
Tested-by: jenkins
The ref manuals for the stm32f2x (RM0033 Rev4) and stm32f4x (RM0090 rev1)
are unclear to the address of the flash size register (F_ID).
According to contacts @ ST this is the correct address, the manuals will be
updated in due coarse.
Change-Id: If9fb83b3100458d17038cf27c2b23355e1dc5a9e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/448
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
This allows us to detect a device arrata where the device id returned is
incorrect.
This issue only effects stm32f4x Rev A silicon.
Change-Id: Ic9f4985f9abf562f97322dcf484199f0a4eb01bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/354
Tested-by: jenkins
The stm32 drivers have been using 0x7ff as the DEV_ID mask, this should
have been 0xfff.
Change-Id: I232469620969d6dd1b9a2a2aa15ec18b947dbb05
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/352
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
add checking of the current flash lock status before performing the unlock sequence (which would fail in an unlocked state)
Change-Id: I693294c9cd2f59e69cb5bf3338120052fd680b1e
Signed-off-by: Bruno FLEURETTE <bruno.fleurette@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/363
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This uses the same controller as the stm32f2x family.
Change-Id: I931a9ceb0cd1219514d14b8b59475179e543dd0f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/338
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
On wrong parameters a error is signalized to the calling function.
Change-Id: I484443fdb39938e20382edc9246d5ec546a5c960
Signed-off-by: Mathias K <kesmtp@freenet.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/282
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Add verification of the flash unlock sequence and return an error if the
flash is still locked.
Add mass erase subcommand.
Change-Id: Id586b1eaf983a3f25b933847dd6608c15bf0b07e
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/281
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use consistent names for the stm32 family flash drivers, eg.
stm32x -> stm32f1x
stm32f2xxx -> stm32f2x
this makes it easier to add support for newer stm32 families.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Spencer Oliver
Andreas Fritiofson
Bruno FLEURETTE
Mathias K
Spencer Oliver