are up and running. The examination and validation is actually
"optional" from the point of view of GDB + telnet servers.
Multiple targets should work fine with this.
- jtag_speed is dropped(divisor is increased), if jtag examination and
validation fails.
- the chain is validated 10x to catch the worst jtag_speed offences
- added LOG_SILENT that can be used to shut up log. Feeble
ersatz for try+catch.
- GDB register packets are now always replied in order to make sure
that GDB connect works. If the target is not halted, then these
packets contain dummy values.
git-svn-id: svn://svn.berlios.de/openocd/trunk@483 b42882b7-edfa-0310-969c-e2dbd0fdcd60
--enable-presto_ftd2xx and --enable-presto_libftdi
- completed trace point support for use with ARM7/9 DCC
- completed debug message output with support for HEX dumps (1, 2 or 4 byte quantities)
- fixed bug in delete_debug_msg_receiver (thanks to Pavel Chromy)
- fixed bug in image_add_section (thanks to Pavel Chromy)
- at91sam7 sector erase reworked (thanks to Pavel Chromy)
- merge consecutive sections during flash image write to work around possible section alignment issues with LPC2000 targets
git-svn-id: svn://svn.berlios.de/openocd/trunk@194 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for usbprog (thanks to Benedikt Sauter)
- make OpenOCD listen for WM_QUIT messages on windows (thanks to Pavel Chromy)
- register at_exit handler to do necessary unregistering (thanks to Pavel Chromy)
- added dummy ETM capture driver to allow ETM to be registered without a capture driver
git-svn-id: svn://svn.berlios.de/openocd/trunk@180 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed bug in jtag.c where JTAG command type was wrong for PATHMOVE commands
- added lattice ISP cable (experimental)
- properly initialize parallel port (clear tristate bit)
- fixed jtag/Makefile.am that failed with some versions of autotools
- print error number if read() in gdbserver.c failed on Windows
- fixed handling of opcodes with bits 27-25 b011 (comment was correct, code had a bug)
- added support for AT91SAM7SE internal flash
git-svn-id: svn://svn.berlios.de/openocd/trunk@122 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for loading .bit files into Xilinx Virtex-II devices
- added support for the Gateworks GW16012 JTAG dongle
- merged CFI fixes from XScale branch
- a few minor fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@116 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added access to ARM920T vector catch register (via generic register mechanism)
- don't disable linefills on ARM920T cores - this lead to lockups when accessing lines already contained in cache
- read content of ARM920T cache and tlb into file (arm920t read_flash/read_mmu commands)
- memory reading improved on ARM7/9, can be further accelerated with new "arm7_9 fast_memory_access enable" command (renamed from fast_writes)
- made in_handler independent from in field (makes the handler more flexible)
- added timeout to ft2232 when using D2XX library
- fixed STR7x protection bit handling on second bank (thanks to Bernard)
- added support for using the OpenOCD on AT91RM9200 systems (thanks to Anders Larsen)
- fixed AT91SAM7 flash handling when not running from 32kHz clock (thanks to Anders Larsen)
git-svn-id: svn://svn.berlios.de/openocd/trunk@90 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- unified 'ftd2xx' and 'ftdi2232' into a single interface 'ft2232'. The library used to access the hardware is choosen during configure with --enable-ft2232_ftd2xx or --enable-ft2232-libftdi.
git-svn-id: svn://svn.berlios.de/openocd/trunk@83 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Added state-move support to ftd2xx and bitbang JTAG drivers (required for XScale, possibly useful for other targets, too)
- various fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@78 b42882b7-edfa-0310-969c-e2dbd0fdcd60
oharboe
mifi
drath