The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new FL1-K family is replacing the FL-K family. The data from all
three was based on the datasheet. In addition the 8MB S25FL164K was
tested successfully with OpenOCD on a custom board.
Change-Id: Idafeed86da12a481c0db92cc0de7ba28f50c2252
Signed-off-by: Anders <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's possible for us to fail to read the part ID code so make sure that
part_info is initialized to NULL before attempting to do so, otherwise
we could proceed and use it uninitialized and then segfault.
Change-Id: I0a3f3d3947690b66f0981b5046340449521e0b33
Signed-off-by: Jack Peel <jack.peel@synapse.com>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2276
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This combination is known to work properly with 2MHz JTAG clock.
Change-Id: Ie5ec3d3b415efbb13faee7d34e0c7f862b78350c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2266
Tested-by: jenkins
Without this SheevaPlug debugging interface can't be matched.
Change-Id: Ifca149130d03c1aa165ed1123e8540e49485f023
Reported-by: Andreas Schneider <schneider.andi@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2265
Tested-by: jenkins
Since now auto-detection for flash size works nicely, there's no
reason to keep numerous configs around.
Change-Id: If0cbc37985abf17ef7c1f7d0688e76500fac228f
Signed-off-by: Vanya Sergeev <vsergeev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1960
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds config to allow JTAG debugging of an ARM core of a modern
hybrid SoC by Research Centre "Module"
(http://www.module.ru/en/company/). К1879ХБ1Я is targetted at set-top
boxes and other multimedia equipment, the official SDK is Linux-based.
Change-Id: Ib2ae5784d25699f952682e66b025a3f677a76d5d
Signed-off-by: Бурага Александр <dtp-avb@yandex.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2272
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the research by Eldar, TINY-H adapter has nTRST connected
to ACBUS0 directly via a 100 Ohms series resistor. I think it's safe
to assume the older TINY adapter does the same.
See high-res photos at [1].
This patch should fix issues with JTAG for the case when nTRST is
actually connected but is missing from the config.
[1] https://wikidevi.com/wiki/Olimex_ARM-USB-TINY-H
Change-Id: Iaaee7be30536ebb502802d38b82cd9573408f854
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2247
Tested-by: jenkins
Reviewed-by: demokmail <demokmail@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Luckily, TI's website has predictable URLs for the datasheets, so it
was trivial to download all the pdfs corresponding to the currently
available 71 TivaC devices. Then they were processed with pdftotext
and parsed by this script:
BEGIN { capture = -1 }
/^Device Identification 0 \(DID0\)$/ { state = "waitingclass0" }
/^Device Identification 1 \(DID1\)$/ { state = "waitingpartno0" }
/^CLASS$/ { if (state == "waitingclass0") state = "waitingclass"
else if (state == "waitingclass") capture = 4 }
/^PARTNO$/ { if (state == "waitingpartno0") state = "waitingpartno"
else if (state == "waitingpartno") capture = 4 }
(FNR == 3) { family = $2 }
{
if (capture >= 0) {
if (capture == 0) {
if (state == "waitingclass")
class = $0
else if (state == "waitingpartno")
partno = $0
}
capture--
}
}
END { print "{" class ", " partno ", \"" family "\"}," }
Change-Id: I6820c409fe535f08394c203276b5af4406fe8b92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2262
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should make current Tiva C parts usable apart from the protection.
Runtime tested on TM4C123GXL (Blizzard) and TM4C1294XL (Snowflake).
Change-Id: Ia64e9d39fbd2b7049578bbfade72435e5203ddf5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2257
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This struct and libusb_get_device_descriptor() method are not present
in libusb-0.1 API, so when libusb-1.0 is unavailable, this code breaks
the build. Fix by using the appropriate struct (which is apparently
filled automatically on device initialisation).
While at it, change return values for consistency with the callers.
Change-Id: I7d85ab9a70401a155a65122397008ae4d81382fe
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2252
Tested-by: jenkins
Reviewed-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is for mx6q TO1.1.
Change-Id: Id6af2ed232fc19be9bf49eb6d2df0004c6668698
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2253
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
Commit f701c0cb seems to have introduced a regression for non-JTAG
transports as the newly created "tap" (DAP actually) ended up being
disabled, thus resulting in total lack of functionality.
This was exposed by a debug log demonstrating ftdi SWD transport
connection to mdr32f9q2i, the target wasn't examined on init and
couldn't be reset.
Change-Id: If53cbe800d4adc177aa3ac3219860e7fa15b3e49
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2261
Tested-by: jenkins
Reviewed-by: Angus Gratton <gus@projectgus.com>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This was very helpful when debugging programs during async loading.
Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds initial support for the STM32L0 family, specifically the ID
code 417 variant. The 'L0 has 128B rather than 256B pages as well as a
different number of pages per sector. It also has several key registers
and register sets in different locations from the STM32L1xx parts.
This change therefore takes the opportunity to reorganize part information into
a const table (it was previously determined by a set of control statements) and
abstracts away some of the low-level details to make them generic for L1 and
L0 parts.
We also include the first bank's size (for dual bank parts) in the new
device information table (and correct that size for the 0x437 variant
which is 256 rather than 192KB).
The 'L0 parts will not use the built-in loader/helper for Flash writing.
Tested on STM32L053 (dicovery board and Nucleo board) and STM32L152
(discovery board).
Change-Id: I57f7a8ab02caee266de71b31ae82a50d85728a0b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This was somehow missed in the chip ID table and of course that's
exactly the one on my board (as such, tested on hardware).
Change-Id: I212d7c729d979e0357f1d4635f40935e25fe6ff3
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2260
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fitted to various Analog Devices ADuCM36x dev boards.
Change-Id: Ib3691704c0ecd2f8cba1abba284aee695d6bc135
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2244
Tested-by: jenkins
As Daniel pointed out, since the rewrite of the USB Blaster driver, the
initialization behaviour has change. The initial flush of the FIFOs is
not longer done with a specific USB setup packet, but with a write
filling up the blaster queues.
The problem is, quoting Daniel :
When the CPLD is in bit banging mode (as is usually the case), the
first 0x00 byte sets all pins to low and disables the output
driver. Disabling the output drivers is a few nanoseconds slower
than changing a pin from high to low, so I see a spike towards GND
on my reset line when that byte is sent over USB. The spike is too
short to have an effect on the board.
When the 4096 0x00 bytes are processed and the TMS=1 is to be
generated, all I see is several microseconds of low level on all
pins, resetting my board.
This patch changes the way the initialization is done :
- at driver init, nothing is sent towards the usb-blaster
This gives time for init script to setup PIN6 and PIN8 (resets)
- at the very first driver command, the initialization is done :
- the output is in bit bigbang mode
- the PIN6 and PIN8 are computed according to init script
- the 4096 computed output is sent
Change-Id: If7ceee957f6b59bcb27c8f912f1cfdd0f94f75ed
Reported-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/2229
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even though changing transport is impossible, reselecting it should be
harmless.
Change-Id: I6c1c2786134e826f47f848b590e6d712b6fd2206
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2251
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When you source a JTAG-SWD converter config, any other transport
doesn't make any sense, so just autoselect it right there.
Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369
Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2248
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In particular -f and -s options may contains paths that can easily
exceed the (old) 128 bytes buffer.
Change-Id: Ifc198536549f50663e8e588519bb9ef75dcd172c
Signed-off-by: Cristian Maglie <c.maglie@bug.st>
Reviewed-on: http://openocd.zylin.com/2241
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- stlink_usb_get_rw_status() had a bug where FAULT or WAIT responses
in read/write operations were ignored, leading to incomplete data.
- Added wrapper stlink_cmd_allow_retry to handle
SWD_AP_WAIT/SWD_DP_WAIT statuses in most commands. These statuses
appear if an SWD read or write received a WAIT ACK response from the
target more than 4 times in a row. The driver retries the operation
(with exponential backoff) before failing outright (in testing 1
retry was always enough.)
- As part of the implementation of stlink_cmd_allow_retry a large
number of lines of boilerplate were refactored.
- Fleshed out stlink_usb_error_check and added it to some more code
paths so WAIT or FAULT responses are logged to debug. WAIT responses
will be logged even if they are subsequently retried, which should
help in case the retries have subtle side effects (none
anticipated.)
Tested with two targets: STLINK F0 Discovery, Nordic NRF51822. Only
tested with STLINK V2 programmers.
Change-Id: I9af24e8f0121b035356dbb9978d6bbf4feb2e4d3
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2201
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to Nordic Semiconductor Product Anomaly Notice (document
NRF51822-PAN), item 16, some revisions of nRF51822 sometimes reset
without all RAM blocks enabled. This was noted on NRF51822-QFAA rev
CA/C0, only 8KiB of memory was accessible.
This patch turns on all RAM following a debugger induced reset
(matches specified behaviour.)
Change-Id: I4f8be4ec3d1271da7fe5bc9a084fdcb2968535bb
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2202
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the -irlen parameter was required even though it is not
a part of the SWD or CMSIS-DAP transports.
This may eventually need to be changed for CMSIS-DAP once that
supports JTAG as well.
Change-Id: Ia02b67840c19c7cf1c7a75063648c0174176a311
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2226
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This workaround broke usage with at least the I.MX6Q.
The comment implies that talking to the J-Link dongle itself should
fail if the target isn't reset, which sounds really strange. I'm
guessing it just triggered another bug in OpenOCD or Segger FW which
might have been fixed since. Revert and wait and see if there are any
failure reports.
Tested with Kwikstik (J-Link + Kinetis K40), not with the mentioned
adapter.
Change-Id: I97f555efe079bd99c098bf483491d9509b2363ad
Signed-off-by: Roy Spliet <rspliet@mpi-sws.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2147
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
During the initialisation a driver might need to communicate with the
target (e.g. sending jtag2swd sequence), so when doing so it should
honour the user-specified speed.
Change-Id: If84fea6057fda9edcf2c0a653edfbab2500e3cdd
[andrew.smirnov@gmail.com: fix khz/hz confusion]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2224
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Austin Phillips
Andrey Skvortsov
Anders
Andrey Yurovsky
Andreas Fritiofson
Nemui Trinomius
Paul Fertser
Vanya Sergeev
Бурага Александр
Angus Gratton
Spencer Oliver
Robert Jarzmik
Eldar Khayrullin
Oleksij Rempel
Cristian Maglie
Andrey Smirnov