this batch of fixes should be pretty straightforward
rename of 'index' and an 'i' local variable shadowing.
'index' conflicts with a global name.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Added a function 'pll_v03_setup' to set up PLLs and clock
dividers on DM365 and DM368.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Here is a patch to fix a startup in C100 (arm1136). Basically make sure
that UART is configured before using it.
Michal
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
found by code inspection. There are many other places in
CFI where LOG_ERROR() should be called similarly...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when a write/unlock/erase failed during write_image, then
an error was not propagated back up so e.g. flash write
image from tcl scripts would not throw an exception.
Also flash filling speed was printed even when the
operation failed. Output is now less confusing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
failure to write to memory was not propagated.
This is an interesting case of broken error handling:
with exceptions we wouldn't have had this at all,
and I also wonder if there is a GCC option to warn
about these kinds of potential bugs.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Parameter "type" of function armv4_5_mmu_translate_va()
is now not used.
Remove the parameter and the "enum" listing its values.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function armv4_5_mmu_translate_va() now properly signals
errors in the return value.
Remove former error handling by setting variable "type" to
value "-1".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function arm920t_write_memory() default return value
should be ERROR_OK.
All cases of local errors are handled immediately and
not further propagated.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 0538081246
introduces a compile time warning:
arm920t.c: In function ‘arm920t_write_memory’:
arm920t.c:567: warning: ‘retval’ may be used uninitialized in this function
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
any read/write operation to memory can fail.
block write algorithm error propagation was broken
in that it would continue after an error was reported
writing data to ram or the algorithm failing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
JTAG_MOVESTATE is misleading, this cmd is only used
for reset.
JTAG_PATHMOVE should be used otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hello,
"stm32x mass_erase" return ERROR_OK even if something goes wrong.
Here is a summary of changes :
* in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error
detected in FLASH_SR register;
* in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the
returned value of stm32x_mass_erase().
I don't know if there is reason to always return ERROR_OK ?
Gaëtan
ETM analyze produced no output when the trace buffer was empty.
This patch provides users with a clue.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Every time command "flash probe #" is executed, memory
structures are re-allocated without preventive free()
of former areas, causing memory leak.
Also, memory allocation does not check return value,
determining segmentation fault in case of out of memory.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
It might be possible to get this target going without
RCLK, but it would require more careful analysis and
usage of the reset events.
Enable fast memory accesses.
Tested on an at91sam9260 custom board w/external DRAM
and flash.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
- As this is a complete unit, including jtag we might as welli nclude
the jtag cfg.
- Add missing id for the str750 that is also in the jtag chain.
- Reduce jtag startup speed to 500kHz.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
We request a id register read at the end of ahbap_debugport_init
but we never actually run the queue. In some cases this causes a
segfault.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Register name fix; ref. TI document sprueh7d
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
I was finally able to figure out the cause of this problem. There are two
parts to the patch. The first patch modifies the configuration file I
originally generated for the Atmel AT91SAM9G20 board and achieves the
following:
+++ Splits the reset-init handler into a reset-start handler for some of the
initial configuration activities and keeps the remainder in the reset-init
handler as was the case before. This was the real issue that was causing
the timing problems I identified before. This solution was confirmed with
an o-scope on actual target hardware.
+++ Adds a new instruction in the reset-start handler to disable fast memory
accesses in the reset-start handler. When the target jtag clock is started
out at 2 kHz during system clock initialization, memory writes (i.e.
register write to enable external reset pin -- basically to RSTC_MR) are
naturally slow and cause GDB keep-alive issues (refer to PATCH 2/2 for
additional fixes).
+++ Modifies the configuration file to use srst_only reset action. The
reset-start/reset-init handler split also now allows the correct behavior to
be used in the configuration file (previously had to use both SRST and TRST
even though only SRST is actually used and connected on the evaluation
board).
+++ Adds external NandFlash configuration support to take advantage of flash
driver added earlier. Doesn't fix any bugs but adds functionality that was
marked as TBD before and thrown in when I did other work on the
configuration file.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This second half of the patch is proposed to clean up some GDB keep alive
issues on arm7_9 targets that start up with very slow clocks. If an attempt
is made to write to key registers on the processor with a slow jtag speed,
GDB timeout warnings appear on the console (at least mine) when "reset halt"
or "reset init" commands are issued from the gdb client:
*** BEFORE PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1026). Workaround: increase "set remotetimeout" in GDB
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1027). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1004). Workaround: increase "set remotetimeout" in GDB
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
I added additional keep alive steps in areas that troubleshooting revealed
were causing problems. I only did this however for non-fast write memory
accesses. I don't think most people would be using fast memory accesses to
write to memory when the jtag and system clocks are slow anyway.
If you disagree with my feeling, think there is a more elegant way to handle
the problem, or think the patch will cause other unforeseen problems with
other targets, let me know. As you can see below, the patch does eliminate
the problem on my development station and I suspect that it will benefit
others.
*** AFTER PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
Gary Carlson
Gary Carlson, MSEE
Principal Engineer
Carlson-Minot Inc.
tcl "puts" didn't work because the logging code sensored strings
that did not include a '\n'. The correct thing is to sensor
empty strings, which are used to keep gdb connection alive.
The tcl "puts" code broke apart strings which do contain '\n' in
order to implement the -nonewline argument, which is how it
got hurt by the bug in log.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Øyvind Harboe
Thomas Koeller
michal smulski
Antonio Borneo
gcembed
Spencer Oliver
Jon Povey
Freddie Chopin
Gary Carlson