Issue warning to user when unlocking or writing the option bytes.
The new settings will not take effect until a target reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Issue warning to user when unlocking or writing the option bytes.
The new settings will not take effect until a target reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This is a copy and paste of arm926ejs. Not tested, but
ready for testing at least. There is a good chance that
it will work if the generic armv4_5 fn's are robust enough...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Copy of the 926ejs function. I have tested it only using
my rtems application (where virtual address mapping == physical).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Sometimes MS-Windows users try to use filesystem names which include
the "#" character. That's generally unwise, since it begins Tcl
comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
reset init would get stuck in an infinite loop when
e.g. khz was too high. Added timeout. This is a copy
of paste of a number of such bugfixes in the arm11
code.
Arm11 code reviewed for further such infinite loop bugs
and I couldn't find any more. Xing fingers it's the last
one...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Not all cores and boards support adaptive clocking, so qualify
all advice to use it to depend on core and board support.
It's primarily ARM cores which support this; and many of the
newer ones (like Cortex-M series) don't.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Doxygen output was previously titled "OpenOCD Reference Manual",
which was quite misleading ... the User's Guide is the reference
manual which folk should consult about how to use the software.
Just rename it to match how it's been discussed previously, and to
bring out its intended audience: developers of this software. As a
rule, Doxygen is only for folk who work with the code it documents.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide doxygen for many of the public ADIv5 interfaces (i.e. the ones
called from Cortex core support code).
Add FIXMEs (and a TODO) to help resolve implementation issues which
became more apparent when trying to document this code:
- Error-prone context-sensitivity (queued/nonqueued) in many procedures.
- Procedures that lie by ignoring errors and wrongly claiming success.
Also, there was no point in a return from dap_ap_select(); it can't fail,
and no caller checks its return status. Clean that up, make it void.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Init the ARMv7-M magic number. Define predicate verifying it.
Use it to resolve a lurking bug/FIXME: make sure the ARMv7-M
specific DAP ops reject non-ARMv7-M targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Have the User's Guide and BUG handling notes both reference
the fact that we now have a bug database at SourceForge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Segger publishes some documentation on this protocol;
reference it, so future maintainers can know it exists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Moved board specific settings from target/at91r40008.cfg to a new
file board/ethernut3.cfg.
Set correct CPUTAPID. Reset delay increased, see MIC2775 data sheet.
Increased work area size from 16k to 128k.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove long-obsolete text about "erase_check" affecting "flash info" output.
Move parts of that text to "protect_check", where it's still relevant; and
update the "flash info" description to mention the issue.
(This is still awkward. It might be best to make "protect_check" mirror
"erase_check" by dumping what it finds, so "flash info" doesn't dump any
potentially-stale cache info.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For STR7x flash, the device cannot be queried for the protect status.
The solution is to remove the protection on reset init. The driver
also initialises the sector protect field to unprotected.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The default state of the STR7 flash after a reset init is unlocked.
The information in the flash driver now reflects this.
The information about the lock status cannot be read from the
flash chip, so the user is informed that flash info might not
contain accurate information.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The semihosting interface has a strange convention for read/write where
the unused amount of buffer must be returned. We failed to return the
total buffer size when the local read() call returned 0.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Test cases ran on v0.4.0-rc1 for a number of targets:
AT91FR40162
LPC2148
SAM7
STR710
STR912
The goal of the testing session was to prove basic functionality of OpenOCD for different targets.
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
srst_asserted and power_restore can now be overriden to do
nothing. By default they will "reset init" the targets and
halt gdb.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When the TAR cache was explicitly invalidated, don't bother
printing it; the actual hardware status is more informative.
Provide some doxygen for the MEM-AP setup routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sometimes we saw two strange blank spaces at the beginning
of the telnet lines.
progress
ogress
>
This patch fixes this problem:
progress
progress
>
The code changes are *reasonably* clean, but perhaps it could be
made a bit more elegant, but I didn't want to change things after
I finished diagnosis/testing & submitting the patch.
The problem was that logging can send the text and the newline
separately in two different requests and the telnet code would
incorrectly remove the prompt from the end of a line.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the MEM-AP cache is invalid, don't display it; just report that
invalidity as an error. (This bug has been observed with "mdw 0 32"
after just a "reset halt". Some code is being wrongly bypassed...)
If it's valid, display that cache at DEBUG level, not ERROR. Also,
don't assume it's an AHB-AP; it could be another flavor of MEM-AP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reject invalid AP numbers (256+) as Tcl operation parameters.
Shrink one of the overlong lines.
Add my copyright to the ADIv5 code (multiple contributions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make messages reference "DAP" if they're actually transport-agnostic, or
"JTAG-DP" when they're JTAG-specific. Saying SWJ-DP is often wrong (on
most Cortex-A8 chips) and is confusing even if correct (since we don't
yet support SWD).
Rename a JTAG-specific routine to jtagdp_transaction_endcheck() to highlight
that it's JTAG-specific, and that identify DAP clients undesirably depending
on JTAG. (They will all need to change for SWD support.)
Shrink a few overlong lines of code. Copy a comment from code removed
in a previous patch (for the ARMv7-M "dap baseaddr" command).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make the ARMv7-M DAP code reuse the command handler for "dap baseaddr".
For some reason, this DAP command wasn't converted earlier.
This is a code shrink and simplification; it also removes a needless
transport dependency on JTAG.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Building with clang took a few very small changes. The change to
helper/log.h is because clang doesn't like an expression where the
result is unused. In helper/system.h, I just defined true and false
since clang doesn't have them builtin.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "-f" is a shortcut for "-c" ... and providing any "-c" options
means the "openocd.cfg" file isn't implicitly used. Both the User's
Guide and the manual page were weak on these points, which has led
to some confusion.
Also update the manual page to include highlights of the search path
mechanism, including the facts that it exists and that "-s" adds to it.
Stop saying only the current directory is involved; the OpenOCD
script library is quite significant.
(Missing: complete manpage coverage of the search path, including a
FILES section listing all components and saying where the script
library is found.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The term "DPM" is probably not well known ("Device Power Management"?),
so identify its source in the current ARM architecture specification.
It's relevant to ARMv6, ARMv7-A, and ARMv7-R ... but not "M" profiles.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cygwin would fail to reopen a previously written file if the mode is
not given.
Simplified converting the open flags and made sure the win32 O_BINARY
bit is set.
Added define for systems that do not support O_BINARY.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
SYS_FLEN would be called before a write on a descriptor to check its size.
Currently lseek would fail with -1 when given the stdout/stderr descriptor.
Changing to use fstat seems to be the standard way of handling this.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
ARMv7-M defines a "lockup" state that's entered in certain double
fault sequences which can't be recovered from without external help.
OpenOCD has previously ignored this.
Issue a diagnostic saying the chip has locked up, and force exit
from this state by halting the core. It's not clear this is the
best way to handle lockup; but there should now be less confusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add space missing after the invalid ACK value. On init, say
which AP is being used, and don't assume it's an AHP-AP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
isspace() parameter must be an integer, else a 'char' gets
used as an array index (sigh).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
More SVF fixes:
* Treat all content between parentheses as part of the same
parameter; don't (wrongly) treat whitespace as a delimiter.
* Use isspace() to catch that whitespace; it's not all single
spaces, newlines etc are also valid.
* When parsing bitstrings, strip leading whitespace too.
So for example, these are equivalent and should (now) be OK:
"TDI( 1234 )"
"TDI( 1 2 3 4 )"
"TDI(00 12 34 )"
"TDI(
00 12
34)"
[dbrownell@users.sourceforge.net: comment updates; trivial cleanup]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
If the target and openocd are idling, the log should normally
be silent at level 3. (Given no verbose logging options.)
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
See http://forum.sparkfun.com/viewtopic.php?p=90983#90983 for discussion;
basically, the SVF parser wrongly expects "TDI (123)" but the space is
optional and it should accept "TDI(123)" too.
In the same way, "TDI(123)TDO(456)" should work too.
Rather than update the command parsing, this just makes sure the expected
spaces are present.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The breakpoint/watchpoint message was wrong for Feroceon and
Dragonite, which have only one working watchpoint unit.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell
Spencer Oliver
Øyvind Harboe
Marc Pignat
Viktar Palstsiuk
Ethan Eade
Harald Kipp
Edgar Grimberg
Nicolas Pitre
Alex Austin
simon qian