Add a header comment referencing useful XScale specs.
Make most data static, and the tables readonly.
Scrub extra blank lines.
Return fault codes from one routine.
Remove a needless NOP methood.
(BUGFIX) When we update R0, mark R0 as dirty/valid ... not R15/PC!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix formatting and layout bugs in the new "translating configuration
files" bit. Make it a section within the chapter about config files.
Add a crossreference.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We added two overridable procedures; document them, and the
two jtag arp_* operations they necessarily expose.
Update the comment about the jtag_init_reset() routine; it's
been obsolete for as long as it's had SRST support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Startup now mostly works, except that the initial target state
is "unknown" ... previously, it refused to even start.
Getting that far required fixing the ircapture value (which
can never have been correct!) and the default JTAG clock rate,
then providing custom reset script.
The "reset" command is still iffy. DCSR updates, and loading
the debug handler, report numerous DR/IR capture failures.
But once that's done, "poll" reports that the CPU is halted
(which it shouldn't be, this was "reset run"!), due to the
rather curious reason "target-not-halted".
Summary: you still can't debug these parts, but it's closer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This abstracts the "jtag arp_init-reset" call into a method
called from OpenOCD startup and reset processing.
Platforms which have different requirements for how such hard
resets must be performed can now override "init_reset" instead
of needing to rebuild custom hacked versions of the server.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is clearly noted in the hardware spec (section 5.2.3); it
works around a chip erratum: "If the MPU_RESET signal is used,
it may cause the EMIFS bus to lock."
I seem to have a board with such an initial build. The chip
is labeled XOMAP. Presumably, parts without that "X" prefix
(eXperimental) resolve this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Observed:
openocd: core.c:318: jtag_checks: Assertion `jtag_trst == 0' failed.
The issue was that nothing disabled background polling during calls
from the TCL shell to "jtag_reset 1 1". Fix by moving the existing
poll-disable mechanism to the JTAG layer where it belongs, and then
augmenting it to always pay attention to TRST and SRST.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Among other things this causes startup errors to kick in the
fallback "reset harder" logic during server startup. Comments
are also updated a bit, explaining what the various error paths
signify (in at least my observation).
There's one class of validation error that we can still plausibly
ignore: when wrong IDCODE values are observed.
This change seems to have helped make an OMAP5912 behave much
more reliably. There's still some post-reset flakiness, but
it's unrelated to scan verification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Without some extra delay after releasing SRST, we seemed to
be trying to talk to the TAP before it was ready to respond.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Also, talk about "mainline" not "trunk".
The release.txt and release.sh files need more updates.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2825 b42882b7-edfa-0310-969c-e2dbd0fdcd60
At least some FT2232 based adapters don't necessarily come up
in the expected state, with SRST and TRST disabled. Since
other adapters could suffer the same problem, let's avoid
needing to patch every driver and just force *all* adapters
to initialize those values properly at server startup.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2824 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Instead of just assuming all IDCODE-deprived TAPs violate the
JTAG spec (they don't!), just require TAPs with such problems
to be declared with proper ircapture/irmask values. Example,
with mask and value of zero.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2823 b42882b7-edfa-0310-969c-e2dbd0fdcd60
It had a very little bit of content; move that to the more extensive
chapter on config file guidelines, and give more current "ls" output
to show the available library code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2820 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- revert to previous default: don't talk JTAG during SRST
- add "srst_nogates" flag, the converse of "srst_gates_jtag"
- with no args, display the current configuration
And update the User's Guide text with bullet lists to be a bit more clear.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2818 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- The guess-rev.sh script is now a tweaked version of "setlocalversion" as
seen in Linux, U-Boot, and various other projects. When it finds source
control support (git, hg, svn) it uses IDs from there. Else (specific
to this project) it reports itself as "-snapshot", e.g. from gitweb.
I verified this new "guess-rev.sh" script runs under Cygwin.
- Also update the generic version strings to be like "0.3.0-dev" (during
development) instead of the very long "0.3.0-in-development". These also
show up in the PDF docs. For better tracking, we might eventually change
these strings to include the version IDs too.
- Change the startup banner version strings so they include the guess-rev
output. Development and release versions with GIT will be like
Open On-Chip Debugger 0.3.0-dev-00282-g7191a4f-dirty (2009-10-05-20:57)
Open On-Chip Debugger 0.3.0 (2009-10-05-20:57)
instead of the previous SVN-specific (even when using git-svn!)
Open On-Chip Debugger 0.3.0-in-development (2009-10-05-01:39) svn:exported
Open On-Chip Debugger 0.3.0 (2009-10-05-01:39) Release
git-svn-id: svn://svn.berlios.de/openocd/trunk@2809 b42882b7-edfa-0310-969c-e2dbd0fdcd60
David Brownell
Wookey
Øyvind Harboe
Rabeeh Khoury
John Rigby
dbrownell
oharboe