Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.8 USB Other' updated the link to the USBprog tool:
http://shop.embedded-projects.net/
Change-Id: I7fa453934ac6a7889e01b22b7e0cb07f42ee168d
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/591
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.8 USB Other' updated the URL to the Versaloon-Link to:
http://www.versaloon.com
Change-Id: Idd92333cb3d87d1b89dfb282134332387df5a0fc
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/592
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.9 IBM PC Parallel Printer Port based' fixed link to
the Wiggler2 project and removed the alternate URL text to retain
style consistency with the other URLs in the document:
http://www.ccac.rwth-aachen.de/~michaels/index.php/hardware/armjtag
Change-Id: I879db1c6eaf683ca6475a0f466f987087c9d60d0
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/593
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In section '2.9 IBM PC Parallel Printer Port Based' fixed link to
ST's flashlink PDF and removed alternate URL text:
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/
DATA_BRIEF/DM00039500.pdf
Change-Id: I99702dd00d4145784baee1f63b5998bf79e06678
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/594
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In Section 2.7 USB ST-LINK based made these two changes:
"they only works with" to "they only work with"
"following method's" to "following methods"
Change-Id: Idfe6c11c3fa6f2157d01697cd7f480a9d495c8e2
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/590
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updated the link for the usbjtag project to the correct URL:
http://elk.informatik.fh-augsburg.de/hhweb/doc/openocd/usbjtag/usbjtag.html
Added a NOTE to indicate the axm0432_jtag as no longer being
available from the axman.com page.
Change-Id: I70727303dad58d9dc0c5f9b7cce219288b762042
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/583
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added the Flyswatter2 to section 2.3 USB FT2232 Based hardware
list.
Change-Id: I6a382644b5a0313d30afb5a97d0a9ea00f01efa9
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/584
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch fixes the link to the Zylin ZY1000 JTAG Probe webpage.
The ZY1000 product line was acquired by Ultimate Solutions, Inc. in May 2011.
Change-Id: If68cd45a0c47aa20b2e4bb62939b2c505c8c8c2e
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/571
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Added support to the FT2232 driver for the FT2232H-based
Digilent HS1 adapter.
Change-Id: Iab6cc15f299badaf115615b5d4d785ecb2273c27
Signed-off-by: Stephane Bonnet <bonnetst@hds.utc.fr>
Reviewed-on: http://openocd.zylin.com/558
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
when -ignore-version is used we should mask of the upper 4bits not 8bits.
Change-Id: I9ffe24c2aeeb414677357a647609fdf018890194
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/473
Tested-by: jenkins
A period or comma must follow the closing brace of an @xref.
Change-Id: Ida5dc3600eca328d95b0a8f6b5c9fe0a0f3ba820
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/475
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
A period or comma must follow the closing brace of an @xref.
Change-Id: I272f1e7fac8f1fee4844f485b0b8e2e4e9cf352d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/456
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This patch adds init_board concept information to OpenOCD manual.
Additionally a link from init_targets chapter to new chapter about
init_board is added.
Change-Id: I09b9aaa1cf68b94f35701224f641cae9811a5bcf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/440
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a note to the docs about the original stlink being broken under linux.
Change-Id: Ib440d78e5c7d31eeace99f611a76fcf701bfb8bc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/433
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
The lm3s variant is not required as this is handled in the
target script - see tcl/target/stellaris.cfg.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
this will allow us to use multiple jlink at the same time as when
the USB-Address is specified the PID change from 0x0101 to
(0x101 + usb_adress)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This piggy backs on JTAG so it's not yet pretty, but that
seems unavoidable so far given today's OpenOCD internals.
SWD init and data transfer are unfinished and untested, but
that should cause no regressions, and will be addressed by
the time drivers start using this infrastructure. Checking
in whould get the code working better sooner, and turn up any
structural/architectural issues while they're easier to fix.
The debug adapter drivers will provide simple SWD driver
structs with methods that kick in as needed (instead of JTAG).
So far just one adapter driver has been updated (not yet
ready to use or circulate).
The biggest issues are probably
- fault handling, where the ARM Debug Interface V5 pipelining
needs work in both JTAG and SWD modes and
- missing rewrite of block I/O code to work on both of our
Cortex-ready transports (Current code is hard-wired to JTAG);
relates also to the pipelining issue.
- omitted support to activate/deactivate SWO/SWV trace (this is
technically trivial, but configuring what to trace is NOT.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
----
doc/openocd.texi | 17 ++
src/jtag/core.c | 3
src/jtag/interface.h | 4
src/jtag/jtag.h | 2
src/jtag/swd.h | 114 +++++++++++++++++++
src/jtag/tcl.c | 2
src/target/adi_v5_swd.c | 281 ++++++++++++++++++++++++++++++++++++++++++++++--
src/target/arm_adi_v5.c | 8 +
src/target/arm_adi_v5.h | 3
9 files changed, 425 insertions(+), 9 deletions(-)
STMicroelectronics controller SMI is not SPEAr specific.
Rename it and change name to every symbol in the code.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Olivier Schonken
Bill Traynor
Stephane Bonnet
Spencer Oliver
Øyvind Harboe
Freddie Chopin
Timo Ketola
Erik Ahlén
Uwe Hermann
Spencer Oliver
Richard Uhler
Jie Zhang
Peter Horn
Michel Jaouen
Phil
Jean-Christophe PLAGNIOL-VILLARD
Aaron Carroll
David Brownell
Antonio Borneo