when last==first==0 then mass erase is executed, it's faster.
the page marking was wrong in this case.
Change-Id: I5c579d59b5c4778cf057cb5986e086abdd4209b2
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/232
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the flash module clock was set according to a spreadsheet from freescale, now it's set according to the configuration file used by the Freescale Flash Programmer.
both work, but i think it's better to use the one used by a software that's made by Freescale (should be correct...)
Change-Id: I382197a3eb43dd47ff4b9b83d5e05008d5613fc6
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/223
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the unlocking procedure erases the flash mem (even if it wasn't locked), so it should be marked as erased after unlocking.
Change-Id: I5cc6a1e1d6cf4e1f243de532eff54111ffd66187
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/222
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
if JTAG debug request fails then halting with a reset should be attempted.
the failure was ignored previously.
Change-Id: Ibec08e2e97f962d164a110c21aaa80bfc17b7f1a
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/221
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
i had assumed two possible halt/debug states:
- halted + debug mode
- running + not debug mode
turns out this one also exists
- halted + NOT in debug mode
added code to handle this in an appropiate way.
Change-Id: Ia0ddcd55d1890c90d100a9e6f5e84ed8dda812a3
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/220
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
now the flash algorithm running on the 568013 checks the buffer_empty bit (instead of the command_finished bit) before trying to write a new word to the flash mem.
this should speed up the flashing procedure. since it is open loop, this change may reduce the risk of failure. flashing will fail if JTAG speed is such that the flash module cannot keep up.
also, the USTAT register is only read once, as suggested in the flow chart provided by freescale (per. ref. manual @ 6-11)
the last step of the flow chart, exiting after commands are complete, is not implemented.
the algorithm will stay waiting for more data. it is up to the PC side to *not* send more data.
Change-Id: I47fe4b50de7da85f80868f5986a89a7e2152616c
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/219
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
moved reset_jtag to the top, since it will be needed in future changes.
also send a define to the .h
Change-Id: I53ef9c02ffa70e7d0416364525a6fbfef855e222
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/216
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
added logging of target error codes to enable automatic error handling from tcl.
the plan is to use a computer to execute a series of tcl commands, the changes allow simple parsing of return messages to detect errors.
Change-Id: Ia98d3bd036e1b6065b475ffff6c1d30baeaf7417
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/215
Tested-by: jenkins
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes an issue when init is called before init_targets has been
executed.
Make sure init_targets is called before init.
Change-Id: Icd5bd4c2a8eea2e399d9de4e331a77560e9672ac
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/235
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Fix error introduced in recent commit.
Correct the name of the board file.
Change-Id: I46bca8329812fb24bc4f8d316be9e7cba9b56496
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/234
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Initial support for SPEAr320 chip and for evaluation
board named EVAL_SPEAr320CPU.
Change-Id: I85524655769bcc610294a26db47a7a399256fbb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/231
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Initial support for SPEAr300 chip and for evaluation
board named EVALSPEAr300.
Currently supports only those parts in common with
SPEAr310.
Change-Id: I8075aa721cf3dfaac561ee51e5df4ce9a2992e3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/230
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code to autodetect DDR was wrong and not complete.
Replaced with a parameter passed to TCL proc.
Split DDR configuration in the two cases of single and
dual DDR chip, using single chip as default.
Change-Id: If39aa518670398e8e4f207d7db6e812a49743e15
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/229
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
DDR controller activation should not be in DDR chip
specific code, but in generic DDR controller part.
Change-Id: If1b178228352b48b0097d7b9b300005fb5bb4fb6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/228
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The support for SPEAr3xx family members does not require
dedicated files for each member.
Join the initialization scripts in a single file.
Change-Id: I45e9dc64809a6f52c4592e3e0eef5529394887c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/227
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The initialization of RAS enable and clock is required by
all SPEAr3xx devices
Change-Id: Iea4cd0902e4da219475d7f35b4c25fc87ec6b902
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/226
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The initialization of memory port 1 is required by
SPEAr310 only
Change-Id: I9d655da1026795f02ff2f82aed36441068cf266d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/225
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ST-AN was mentioned but there was no reference
Change-Id: Ie065f8faba94d63cf391a994ec895692d499394e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/224
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The configuration script check for libusb-1.0 availability first and only
if not found check for libusb-0. So if both libraries are installed on the
system the build script will use libusb-1.0
It's possible to force compiling with libusb-0 with the --enable-libusb0 switch.
If the driver support only libusb0 the script check anly for it.
Change-Id: I7eb045d4e2bd553abefad53f3f4023ff46b0f5f6
Signed-off-by: Mauro Gamba <maurillo71@gmail.com>
Reviewed-on: http://openocd.zylin.com/33
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This reverts commit 0ef5a90d93c5a026bcf70132e60e957ae339d1e1
Causes older versions of gcc to break - need to look into a better fix.
This passed through the jenkins build as we originally did not build this module - we do now.
Change-Id: Iafeac8442b2249269ff45a52ccd3e2870920f635
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/214
Tested-by: jenkins
fix issue when using tms_sequence short
see Trac #31
Change-Id: I22a9cd2af59eae4d8a276dae60b6a99d05af53bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/201
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The calculation for reg_packet_size in gdb_get_registers_packet() could
generate a wrong result in the case of multiple registers whose size is
not a multiple of 8.
The current calculation sums the sizes for all registers then rounds the result
up to the next multiple of 8.
Instead it should round each register size up individually and sum the results for all registers.
Change-Id: Idfb5e5eeee0e69a6889dbe9769c0bf17feacb63b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
gdb_memory_map() correctly calculates the target specific number of flash banks, but then uses the total number (all targets) instead of the target specific number to construct its GDB response, causing a crash.
Change-Id: I3f8639b3e90303a59753ebe140ce4fff96fd5db0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/199
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Based on the K40/Kwikstik config files
Change-Id: Icb3adc7126bacea65209b712ebaa0eb3b894372e
Signed-off-by: Tomas Frydrych <tomas@sleepfive.com>
Reviewed-on: http://openocd.zylin.com/210
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Don't call a variable num_pages if it holds the flash size. Also rearrange
flash size to num_pages calculation to avoid divide-by-zero if there will
be a device with < 1024 byte pages someday.
Change-Id: I2febea39694a2f9750de141f52ec88ae1599c086
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/211
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
in_mask and in_idx are just another encoding of the same state information
that is already kept in bitq_in_state.bit_pos so derive them from that
instead of maintaining them separately.
Change-Id: I4ac6bbe923698a8c1090a785b8babcbb90f82931
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/207
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this at least checks the post conditions after convoluted code.
Change-Id: Idfa8cbedce5288d8bae5743687949f141dfb07b2
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/187
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
in_buff is only ever set to field->in_value and that pointer is still
available when the parsing is restarted so it could just as well be used
directly, removing the need for the static variable.
Change-Id: I3dd7a8315ed5c5bdc3bfb74044f89492bca9816c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/206
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
field->in_value is already checked so it must be non-null here, which means
the else clause can never execute so the entire buffer allocation and
handling code is completely dead.
Change-Id: Id465012a7e607349401d554fc7a8e5db7e967998
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/205
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Check whether the destination is in the program flash or NVM regions,
in the former case, use the normal longword mechanism, not the fast NVM
write.
Change-Id: I7366b7c8919928ee690252df83b99701776aee82
Signed-off-by: Tomas Frydrych <tomas@sleepfive.com>
Reviewed-on: http://openocd.zylin.com/194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a successor to the Flyswatter cable and is very close to the original.
The new revision is based on FT2232H.
Change-Id: Icc6efcf0e4f9d8a10b65df8679b4973f6b375a9f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: David Anders <danders@tincantools.com>
Reviewed-on: http://openocd.zylin.com/193
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Before this commit, openocd used to segfault when probing flash
of an at91sam7x512 (which contains 2 banks of flash). This was due
to the way it systematically insert a new flash bank without setting
its name.
Then, when get_flash_bank_by_name_noprobe() is called, it is doing
a strcmp() on the non-initialized bank->name.
This commit prevents allocation of second probed bank if it is already
allocated (for example, if it is set in a target config file). If a
new bank really needs to be allocated, it ensures that a default name
is set.
Change-Id: I38d15bef1fda2ec746efad37171975136cf7b371
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/171
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
there are no comments about what the rules w.r.t. null pointers
are and it is inconsistent.
It's simply a bug in the app if we ask about the properties of a null
pointer w.r.t. what kind of target it is. It's equally wrong to say
that it is an arm target as that it isn't an arm target.
Change-Id: I0925a6a5c8b38e594ffa7c3ca4390487b5e9b718
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/168
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The CPLD on the xds100v2 expects to see a rising edge on PWR_RST to
enable the outputs. This patch creates that transition correctly by
fixing the direction register for PWR_RST.
THe CPLD will also loop back the data if the LOOPBACK signal is
asserted. Set this signal to an output and keep it clear.
This was tested with a TI DM3730 Beagleboard xM.
Change-Id: I4ea216bef6ae5c40e935741af5c69dc844d5d494
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-on: http://openocd.zylin.com/189
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
rodrigo_l_rosa
Spencer Oliver
Antonio Borneo
Mauro Gamba
Robert Pasz
Philip Nye
Tomas Frydrych
Felix Ruess
Andreas Fritiofson
Øyvind Harboe
Marek Vasut
Aurelien Jacobs
Kyle Manna