Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Commit 246782229f ("smp: replace commands smp_on/smp_off with
"smp [on|off]"") deprecates some multi-word comments, when openocd
was unable to properly handle mixes of multi-word commands and tcl
procedures having a common initial word.
This limitation is over, so move in startup.tcl the multi-word
commands deprecation, making it easy to remove them after a grace
period.
Change-Id: Icb550d1fa7559b95692d2a1244880da6c90ec0b2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5677
Tested-by: jenkins
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
By default GDB timeouts after 2 seconds, even if this value can be
modified with GDB command "set remotetimeout".
On OpenOCD side, the default event for GDB attach is to halt the
target and wait it to halt. But here the default timeout of the
halt command is 5 seconds!
If the target cannot be halted (e.g. it's kept in reset by another
core or the debugger doesn't have enough privileges) then GDB will
timeout while OpenOCD is still waiting and is unable to
communicate with GDB.
Decrease the halt timeout to 1 second in the default GDB attach
event handler.
Change-Id: I231c740816bb6a0d74b0bc679a368a6cbfb34824
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5687
Tested-by: jenkins
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this patch contains several changes to run control and state
handling together with gdb:
- graceful handling of target/gdb desync on resume, step and halt
- a default gdb-attach event executing the "halt" command, to meet gdb
expectation of target state when it attaches
- call target_poll() after Ctrl-C command from gdb
- call target_poll() after resume and step through a vCont packet
- fix log message forwarding on vCont stepping, also move an aarch64
log message from INFO to DEBUG level to prevent messing up the gdb
console during source-line stepping
- fix oversight in vCont support that messes up breakpoint handling
during stepping
Change-Id: Ic79db7c2b798a35283ff752e9b12475486a1f31a
Fixes: d301d8b42f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4432
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The '-defer-examine' option to target create allows declaring targets
that are present on the chain, but not fully functional. They will
be skipped by the initial arp_examine as well as arp_examine after
reset.
Manual examine using 'arp_examine' is needed to examine them, with the
idea that some kind of actions is neeed to bring them to a state where
examine will succeed (if at all possible).
In order to allow value less options to target command, I had to relax
the goi.argc check in jim_target_configure().
Change-Id: I9bf4e8d27eb6476dd9353d15f48965a8cfd5c122
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3076
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This adds init_board procedure that behaves exactly the same as
init_targets - it can be overriden by "next level" scripts. This
procedure is executed after init_targets, allowing common stuff (jtag
chain, memory, flash, ...) to be configured in target script (via
init_target) and leaving rest (like additional memory, reset
configuration, reset-init handlers, ...) to be done in init_board.
This makes init_targets scheme more complete and easier to use - current
board scripts will not need new init_targets, because everything can be
"packed" in init_boards. Moreover it solves the problem of variables
being set in init_targets (executed after init), which were not
accessible by "linear" scripts (parsed before init). All that has to be
done is to enclose all code in board config file in init_board
procedure.
Change-Id: I0736b1ff9873a687966407d62b58ccf29a8e597b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/427
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
this allows configuration scripts to export a init_targets proc
rather than setting up the target directly.
This allows for new conventions in how to set up target vs. board
script and how to transfer default settings between board and
target scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Use correct tcl syntax to throw exception.
the syntax is "return -code error" not "return -error"
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Moves definitions for each layer into their own file, eliminating
layering violations in the built-in TCL code. Updates src/Makefile.am
rules to include all files in the final startup.tcl input file, and
others Makefile.am rules to distribute the new files in our packages.
Marc Schink
Antonio Borneo
Tomas Vanek
Oleksij Rempel
Oleksij Rempel
Matthias Welwarsky
Paul Fertser
Spencer Oliver
Freddie Chopin
Øyvind Harboe
Zachary T Welch