Commit Graph

8201 Commits

Author SHA1 Message Date
Tomas Vanek 66d924f787 flash/nor/kinetis: implement flash bank deallocation
Change-Id: I8ef80eae646d3b3eb7f6dd42067f8516adc5abef
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4415
Tested-by: jenkins
2018-04-10 06:18:35 +01:00
Tomas Vanek c8c20b7c0b flash/nor: handle flash write alignment/padding in the infrastructure
Most of flash drivers have to ensure proper flash write block alignment
and padding. As there was no support for it in the flash infrastructure,
each driver does it its own way. Sometimes this part of code is not properly
tested and contains bugs.

flash_write(_unlock) joins all image sections targeted to one flash bank
using padded areas as a glue. This solves alignment problems on section
boundaries but imposes other problems.

Introduce new flash bank parameters write_start_alignment,
write_end_alignment and minimal_write_gap.
New flash drivers can just properly set these values instead of handling
alignment by its own.

Adapt infrastructure (namely flash_write_unlock(), handle_flash_fill_command()
and handle_flash_write_bank_command()) to prepare write data padded
to an alignment required by the flash bank.

Rework flash_write_unlock() to discontinue write block when the gap
between sections is bigger than minimum specified in minimal_write_gap.
minimal_write_gap is set to one sector by default.

Change-Id: I4368dd402dfaf51c193bcbf1332cffff092b239b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4399
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
2018-04-10 06:17:52 +01:00
Tomas Vanek a867e36f78 target armv7m: multi-block erase check
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
	flash read_bank 0 /dev/null
takes 48 seconds.

erase_check without this change:
	flash erase_check 0
takes horrible 149 seconds!!

And the same command with the change applied takes 1.8 seconds.
Quite a difference.

Remove the erase-value=0 version of algorithm as the new one can check
for any value.

If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.

Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
2018-04-10 06:17:00 +01:00
Tomas Vanek eb8912ec38 target, flash: prepare infrastructure for multi-block blank check
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.

The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).

Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.

default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.

Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
2018-04-10 06:16:40 +01:00
Niklas Söderlund f00d9bb1d7 tcl/target: Add Renesas R-Car R8A7791 M2W target
Add configuration for the Renesas R-Car R8A7791 M2W target.
This is an SoC with two Cortex A15 ARMv7a cores, both cores
are supported.

This patch is based on initial submission by Adam Bass and
improvements by Niklas Söderlund.

Change-Id: I297da62b9ce71ad222a401d98e6bcb8502427673
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Adam Bass <adam.bass@renesas.com>
Cc: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-on: http://openocd.zylin.com/4485
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-09 20:18:29 +01:00
Paul Fertser 6e356cbfe2 HACKING: document practices to improve code quality
Change-Id: I58a7d978b7d5bca3037c4535f06746b9f4411950
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4343
Tested-by: jenkins
2018-04-09 09:05:58 +01:00
Paul Fertser 70b15f989f configure: disable all drivers when zy1000 is enabled
This also fixes the transport_is_hla FIXME.

Change-Id: I33960f373f11e3e203f9aed9c6d02bf7ca48ac97
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4473
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-09 09:04:46 +01:00
Tomas Vanek dbd7e80eb4 gdb_server: gdb_memory_map() rework
Use sector sizes instead of bank size.

Detect a gap between sectors and emit xml blocks accordingly.

Detect sector overflow over the bank size.

Change-Id: If0e0e44b0c3b93067b4d717c9c7b07c08582e57b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4436
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-07 20:34:28 +01:00
Armin van der Togt 4f2c3e6c4f rtos: Fix XPSR_OFFSET for cortex_m4f stacking
Structures rtos_standard_Cortex_M4F_stacking and 
rtos_standard_Cortex_M4F_FPU_stacking in rtos_standard_stackings.c 
where using rtos_standard_Cortex_M3_stack_align for the stack-align 
function. This function calls rtos_Cortex_M_stack_align with 
XPSR_OFFSET = 0x3c. This offset is correct for cortex-M3 but not for 
cortex-M4F and cortex-M4F with fpu. This patch adds stack_align 
functions for M4F an M4F_FPU

Change-Id: If6a90b1898fccbb85619a10f3aef5277dd88ce47
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Reviewed-on: http://openocd.zylin.com/4037
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-07 20:33:39 +01:00
Matthias Welwarsky db456e209f target: free target SMP list on shutdown
On SMP targets, the "target smp" command creates a list of targets
that belong to the SMP cluster. Free this list when a target gets
destroyed on shutdown. For simplicity, the complete list is free'd as
soon as the first target of the SMP cluster is destroyed instead of
individually removing targets from the list.

Change-Id: Ie217ae1efb2e819c288ff3b1155aeaf0a19b06be
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-07 20:33:01 +01:00
Tomas Vanek 414213a5ea target/arm_adi_v5: extend apcsw command to accept arbitrary bits
apcsw command was limited to SPROT bit only.

Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7

Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-07 20:31:37 +01:00
Tim Newsome 2e2bb14b27 Add gdb_report_register_access_error command
With this option enabled (it's disabled by default) errors accessing
registers are returned to gdb. Otherwise they are ignored and success is
reported to gdb. (This is the current behavior.)

We want this for RISC-V, but there's still some cleanup that needs to be
done before that can be upstreamed.

Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I7e56109ea52d18b780c14a07fb35f9e6e8979da4
Reviewed-on: http://openocd.zylin.com/4452
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
2018-04-07 20:31:14 +01:00
Matthias Welwarsky 0dba1815e6 arm_adi_v5: Add ability to ignore the CSYSPWRUPACK bit
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.

Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-07 20:30:12 +01:00
Stefan Arnold be87994d60 flash/nor/at91samd: Add "nvmuserrow" command.
Add option "nvmuserrow" to "at91samd" for changing and reading the register at 0x804000 which represents various fuses.

Change-Id: I6382cc4ac15e6b9681e2f30b0ae60397a6289c3b
Signed-off-by: Stefan Arnold <sarnold@sh-sw.de>
Reviewed-on: http://openocd.zylin.com/4260
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-06 10:37:31 +01:00
Tomas Vanek b08900badc nrf51: Add HWID 0x008F again
HWID originally added in commit 7829f31a6d
was accidentally omited during refactoring in commit
52885d2b53

While on it move old ingeneering sample of 51822 to block of 51822 rev 1

Change-Id: Ie9f15563792a27a72e71df6edbcc6b04490370ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4437
Tested-by: jenkins
2018-04-04 21:27:33 +01:00
Tomas Vanek 7829bb701f drivers/kitprog: workaround KitProg firmware bug of missing ZLP
KitProg firmware does not send a zero length packet at the end of the bulk-in
transmission of a length divisible by a bulk packet size. This is inconsistent
with the USB specification and results in jtag_libusb_bulk_read()
waits forever when a transmission of specific size is received.

Limit bulk read size to expected number of bytes for problematic tranfer sizes.
Use 1 second timeout as the last resort.

Change-Id: Ice80306424afd76e9fbc6851911ffd5109c84501
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4426
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
2018-04-04 21:26:59 +01:00
Cody P Schafer a28dea0fe4 target/cortex_m: avoid dwt comparator overflow
Avoid ever overflowing the DWT_COMPARATOR array by allocating space for
16 comparators (the field is masked by 0xf).

On a stm32f767zi chip (on a nucleo-767zi board) I've been seeing crashes
with address sanitizer enabled due to its (apparent) 10 present
comparators. This appears to be due to
https://sourceforge.net/p/openocd/tickets/178/.

In non-address sanitizer builds, this would likely cause some random
memory to be written to in some cases. (see above bug for observations).

Change-Id: I2b7d599eb326236dbc93f74b350c442c9a502c4b
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4458
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-04 21:24:53 +01:00
Michele Sardo 6e6f90d1af Fix for warnings detected by clang static analyzer
Fix for potential memory leakage and for unused/unreported return error code

Change-Id: Ifb2c95b60637c3a241ad4bf41d1a328c92ccea4b
Signed-off-by: Michele Sardo <msmttchr@gmail.com>
Reviewed-on: http://openocd.zylin.com/4476
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-04-04 21:23:57 +01:00
Tomas Vanek 7690a74b09 flash/nor: implement flash bank deallocation in drivers with simple alloc
All drivers which simply allocate one driver_priv memory block
per each bank now use default_flash_free_driver_priv()

Change-Id: I425bf4213c3632f02dbe11ab819c31eda9b2db62
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4417
Tested-by: jenkins
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-04-04 20:14:18 +01:00
Robert Jordens 3d3b45af46 xilinx-dna.cfg: generic tools for reading Xilinx Device DNA
Most Xilinx FPGA devices contain an embedded, unique device identifier.
The identifier is nonvolatile, permanently programmed into the FPGA, and is
unchangeable providing a great serial / tracking number.

This commit adds generic support for reading the Xilinx Spartan 6 and 7
Series (Kintex, Artix, Ultrascale) Device DNA. The code is similar to
the function in fpga/xilinx-xc6s.cfg for Spartan 6 but the register
addresses are different and the logic has been simplified.

The code was not placed in xilinx-xc7.cfg. The approach of defining taps
in the same file as library code to use them is fundamentally broken on
boards that have more than one FPGA or other chips. This commit (like
the addition of support for Xilinx XADC) starts to remedy that by
splitting library code from board-specific fixed definitions.

The support code is sourced in the Kasli and KC705 board support files
as it was tested on these boards.

Change-Id: Iba559c7c1b7e93e1270535fd9e6650007f3794da
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4396
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 16:22:42 +01:00
Robert Jordens 27473588a4 tcl/fpga/xilinx-xadc.cfg: add support for XADC
The 7 Series FPGAs contain an on-chip 12 bit ADC that can probe die
temperature, internal power supply rail voltages as well as external
voltages. The XADC is available both from fabric as well as through the
JTAG TAP.

This code implements access throught the JTAG TAP.

https://www.xilinx.com/support/documentation/user_guides/ug480_7Series_XADC.pdf

Change-Id: I6cef4d0244add71749fa28b58a736302151cc4dd
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4395
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 12:53:50 +01:00
Tomas Vanek 6eba3777fc jtag/core, target: unregister JTAG events
Also call adapter_exit() before command_exit() as the latter releases
Jim interpreter so JTAG events should be released before.

Fixes memory leak reported by valgrind

Change-Id: I493f3fcba34ea2b4234148e79a4e329c866e0f05
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4474
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:15:23 +01:00
Tomas Vanek 37deb37593 target: fix display halt message logic
If a target is run from gdb and then stopped from OpenOCD telnet interface,
halt does not show message with status and PC registers.

While on it rename 'display' to 'verbose_halt_msg' and use bool type
instead of int.

Change-Id: Ibe6589015b302e0be97258b06938c297745436a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4475
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:14:56 +01:00
Tomas Vanek f035b0851b flash/nor: implement flash bank deallocation on OpenOCD exit
Change-Id: I8fcf09b2a85b3b68743f5fd68a31edea933b9b17
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4414
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:13:09 +01:00
Robert Jordens 38607b2e56 tcl/board: add support for Kasli
Kasli is an open hardware FPGA board. It is part of the Sinara family of
devices designed to control quantum physics experiments (see Sayma_AMC
for other boards already suppported by openocd).

Kasli was developed as part of the opticlock project. It features a
Xilinx Artix 7 100T FPGA, DDR3 RAM, a clock reconstruction and
distribution network, four 6 Gb/s transceiver links (three SFP and
one SATA) as well as interfaces to up to 12 Eurocard Extension Modules
(EEMs).

https://github.com/m-labs/sinara/wiki/Kasli
http://www.opticlock.de/en/

Change-Id: I88b5e9f16b79e1e731056c45da6b5e1448d2c0e7
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4341
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:08:21 +01:00
Robert Jordens 33f70625d7 sayma_amc: add Sayma AMC board definition
Change-Id: I4a3dc5fe2d81b6906099af8cc1a360b3cf4a6b80
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4237
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:08:10 +01:00
Robert Jordens ca3228dda6 kcu105: add support for Xilinx KCU105
* Development board with Kintex Ultrascale XCKU040
* Dual SPI 256 MBit flash, supported through xilinx_bscan_spi

Change-Id: I478ec7481beedd270bfba8af56a93301b0ee3028
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4189
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:07:58 +01:00
Robert Jordens 7944ebb694 xilinx-xcu: add Xilinx Ultrascale tap data
The Ultrascale series is a bit more complicated to handle since with the
stacked and interconnected dies the IR gets longer. This adds support
for all currently known chips from the Ultrascale family.

Change-Id: Ibac325dd6fadc76f73cc682b1c62c1a5f39f0786
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4188
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 10:07:49 +01:00
Matthias Welwarsky 2231da8ec4 target: restructure dap support
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
  instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
  longer references the dap, daps are now independently
  created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
  power cycle)
- update documentation
- update target files

Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 09:58:21 +01:00
Matthias Welwarsky 7274090456 tcl/board: add configuration for the avnet ultrazed-eg starter kit
also contains target configuration for the Xilinx UltraScale+
platform

Change-Id: I6300cbc85c1ed71df71d8aaca59500bbf18f0093
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4467
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 09:48:35 +01:00
Matthias Welwarsky f444c57bf2 arm_cti: add cti command group
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.

Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-30 09:48:03 +01:00
Matthias Welwarsky 1756f393e4 aarch64: add cpsr bitfields to target description
provide meta information for the cpsr so gdb can display the status
flags and not only a hexadecimal number

Change-Id: I9d3fb29153780adbea389d7e4175d5e19bddc256
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4460
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-27 09:15:43 +01:00
Matthias Welwarsky 0808c6e8a3 tdesc: bitfields may carry a type
a bitfield may carry a type (bool or int), add support for that.

Change-Id: Ic831a9b8eac8579e8fdd7d0f01b7f1c9259e6739
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4459
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-27 09:15:27 +01:00
Tomas Vanek 78a44055c5 transport: add transport_is_hla()
and move declaration of all transport_is_xxx() functions to transport.h

Change-Id: Ib229115b5017507b49655bc43b517ab6fb32f7a6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4469
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-20 11:48:44 +00:00
Paul Fertser 828ee07657 server: bind to IPv4 localhost by default
Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.

If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.

Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
2018-03-18 12:59:43 +00:00
Matthias Welwarsky ffd6b78a2c aarch64: fix debug entry from EL0
If we enter debug state from EL0, some registers are not accessible.
Temporarily move to EL1H and back to gain access. Also, fix
armv8_dpm_modeswitch() to not immediately restore the previous state
on elevating the privilege level.

Change-Id: Ic2a92109230ff4eb6834c00ef544397a5b7ad56a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4461
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-16 08:58:06 +00:00
Matthias Welwarsky 935f0c5cc2 gdb_server: fake step if thread is not current rtos thread
gdb assumes that a rtos can make any thread active at will in response
to a 'Hg' packet. It further assumes that it needs to step-over after
setting a breakpoint on frame #0 of any non-current thread. Both
assumptions are not valid for an actual rtos. We fake the step-over to
not trigger an internal error in gdb. See
https://sourceware.org/bugzilla/show_bug.cgi?id=22925 for details.

Change-Id: Ida60cd134033c1d58ada77b87fe664a58f61e2c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4448
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-16 08:57:20 +00:00
Matthias Welwarsky cbf7889873 gdb_server: fix ignored interrupt request from gdb during stepping
Normally, when a ctrl-c is received from gdb, a SIGINT is reported back
unconditionally to tell gdb that the target has stopped in response.
However when a rtos support was configured, the rtos awareness overwrote
the signal with an actual thread state, which gdb then ignored and got
stuck without the user able to interrupt.

Change-Id: I40fd62333e020a8c4d9df0079270e84df9c77f88
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4445
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-03-16 08:56:38 +00:00
Tomas Vanek a4cdce0129 gdb_server: prevent false positive valgrind report
Change-Id: Ia59fdf8a23043889840122859b0c5bdb5f757703
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4420
Tested-by: jenkins
2018-03-15 17:10:33 +00:00
Tomas Vanek ff23980434 drivers/ftdi: free allocated memory
Also uses calloc() for mpsse_ctx->write_buffer to prevent a false
positive valgrind report
"Syscall param ioctl(USBDEVFS_SUBMITURB).buffer points to uninitialised bytes(s)"

Change-Id: I91963371d15c21ea0fee4c40c1da86174db44520
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4418
Tested-by: jenkins
2018-03-15 17:10:16 +00:00
Tomas Vanek 71f5f6eb14 src/jtag/hla: free allocated memory in hl_interface_quit()
Change-Id: If6ead00e47021c88e4c106b4aeaf038db87ff50b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4413
Tested-by: jenkins
2018-03-15 17:09:56 +00:00
Tomas Vanek 7ad11de2fa target/target: free what leaked in target_destroy()
Free event_action, fileio_info and working area.

Change-Id: Iac81230423e92304b8e2c971d0ec71a96b693fc4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4412
Tested-by: jenkins
2018-03-15 17:09:30 +00:00
Tomas Vanek 63d7688245 jtag/core: free all taps and daps in adapter_quit()
Change-Id: I74496f6ddfb0a72b2933e8d682a73a694b8d107b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4411
Tested-by: jenkins
2018-03-15 17:09:09 +00:00
Tomas Vanek 33a3355304 server: free strduped port numbers
Although the leak is negligible, the clean heap on exit will ease
valgrind testing.

Change-Id: I3a7a9c8e8dc7557aa51d0b9caa244537e5e7007d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4410
Tested-by: jenkins
2018-03-15 17:08:53 +00:00
Tomas Vanek ae5b30ae96 openocd.c: call server_quit() for cmd line with -c shutdown
If OpenOCD command line contains -c shutdown, server_quit() is not called.
Though if -c init is also on command line, gdb_server is already initialized.

Call server_quit() on both successful and failure exit from command line.

Change-Id: I6df41c5df045b61d84a5515d1abaa5dc96bc30ac
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4409
Tested-by: jenkins
2018-03-15 17:08:34 +00:00
Tomas Vanek a0b76360b8 tcl/target: warn if a Kinetis MCU is connected to a high level adapter
Make sure the user is aware he can lock the device though unlock is not
possible without access to MDM-AP.

Change-Id: I92676530e95d19489c6739748a99c2895849f90f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4403
Tested-by: jenkins
2018-03-15 17:07:56 +00:00
Paul Fertser 437925c141 doc: fix xref texinfo warning
Change-Id: Iff1ba5836e3a4f352903c3a5ae73c7d992306d42
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4466
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
2018-03-15 13:40:53 +00:00
Tomas Vanek 6f700d2b1c doc: make gdb-attach description understandable
Change-Id: I31babf4e3bbe7c94f26818d938699562a4a26d48
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4465
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-03-13 10:55:35 +00:00
Matej Kogovsek ffb93ef371 jtag: drivers: add support for FT232R sync bitbang JTAG interfaces
Change-Id: Ib88a9e270f5c2a50902a137bcc97fdefd5aad1c6
Signed-off-by: Matej Kogovsek <matej@hamradio.si>
Reviewed-on: http://openocd.zylin.com/4215
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-03-13 08:47:46 +00:00
Paul Fertser 6e76e56e2e target: hla: check return value of hl_dcc_read
This should fix "Assigned value is garbage or undefined" warning
reported by clang:
http://build.openocd.org/job/openocd-clang/doclinks/1/report-391318.html

Change-Id: Ib9488fadca871814328501e415f88822291e0c96
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4332
Tested-by: jenkins
2018-03-13 08:42:17 +00:00