There were a couple of problems with previous implementation:
* Misalligned read would return ERROR_OK and print all zeroes.
* CMDERR_BUSY for abstract access was improperly handled:
According to the spec, no assumptions can be made about DM_DATA*
contents in such a case, but these were considered valid values from
memory.
* A fallback to one element read was implemented when DMI_STATUS_BUSY
occurred during batch reads, even though this can be accounted for.
Change-Id: I09174c61c951b2bb97a529b7f0aa5afaa995179b
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Board config file for ESP32-S3, to allow communication with
the builtin USB-JTAG adapter.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1310f5db30f7df38fe9344f7ba2334611b53863e
Reviewed-on: https://review.openocd.org/c/openocd/+/7749
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This config file enables communication over USB-JTAG with
ESP32-C3, ESP32-S3, ESP32-H2 and ESP32-C6 chips
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Iceea26972588d8c4919d1f3248684ece48ca9121
Reviewed-on: https://review.openocd.org/c/openocd/+/7748
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory region addresses are not in use for now.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9a2189e956ae59b56245ec914ab16719df857b2d
Reviewed-on: https://review.openocd.org/c/openocd/+/7762
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Right after target halt, some activities needs to be done
such as printing exception reason, disable wdts and reading
debug stubs information.
Missing activities will be submitted in the next patches.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I27aad5614d903f4bd7c8d6dba6bfb0bdb93ed8dc
Reviewed-on: https://review.openocd.org/c/openocd/+/7757
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ifb0122f3b98a767f27746409499733b70fb7d0e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I36c86fe4ebc99928ce48a5bff8cb9580a0fa3ac0
Reviewed-on: https://review.openocd.org/c/openocd/+/7746
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9181737d83eeba4e983b6a455b8a1523f2576dd2
Reviewed-on: https://review.openocd.org/c/openocd/+/7745
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Consolidate commonly used commands and variables from
chip config files into functions in esp_common.cfg.
This includes "jtag newtap," "target create,"and "configure -event."
Enhances code reusability and simplifies maintenance.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9e8bf07a4a15d4544ceb564607dea66837381d70
Reviewed-on: https://review.openocd.org/c/openocd/+/7744
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
See section 57.6.1 in RM0432.
Change-Id: Ic4977aee74d1838f420c1d9ff19925d09f8f6e2b
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add more ultrascale devices. Set instruction codes for SSI devices
such that refresh/program read_stat and user registers will work.
Change-Id: Id0a0706f4016eb8a4732725a5b72ae61efd73421
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7716
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Adding a single file for each different ir-length.
Change-Id: Iba3dd55b91c28fdb4d0cafa1ededd939fe61a267
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7715
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
1. update RISCV_MAX_HARTS to 2^20 according to SPEC
2. remove RISCV_MAX_REGISTERS, it's not used anywhere anymore
3. add parentheses
Change-Id: Iadf0fa1ba3bbe5b9420b8430883e140db87f4f9e
Signed-off-by: Mark Zhuang <mark.zhuang@spacemit.com>
If a target where a software breakpoint was set is not currently
available, but there are other targets in the same SMP group that are
available, then we can use those to remove the software breakpoint.
Change-Id: I9faa427c7b3aee31504e6e6599539e6f29b58d8f
Signed-off-by: Tim Newsome <tim@sifive.com>
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use configurable virtex pld driver to add support for more
xilinx fpga families.
Change-Id: Iff10c8c511787734fa289bdba15f03131d51e071
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7352
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
According to section 5.6 in the RISC-V debug specification, the previous
way to set triggers was incorrect, as was discussed as part of
https://github.com/riscv/riscv-openocd/issues/870. This commit fixes the
sequence to be in line with the specification as well as adds some comments
to clarify for any future reader as to what is actually done.
Change-Id: Iffc5cc0f866a466a7aaa72a4c53ee95c9080ac9d
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
this functionality allows to query if a target belongs to some smp group
and to dynamically turn on/off smp-specific behavior
Change-Id: I469453d95e7c1640a91bc60d80c854404e508535
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
This patch fixes the handling of errno by setting the sys_errn
only if error has actually occurred during the semihosting call.
It also fixes few issues where error was not set in the first place.
Change-Id: I2fbe562f3ec5e6220b800de04cd33aa1f409c7a0
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This patch introduces function semihosting_opcode_to_str() which
converts semihosting opcodes to strings. This function is then
used in debug messages to improve log analysis and troubleshooting.
Change-Id: Iffea49dae13d6a626ae0db40d379cba3c9ea5bd3
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7726
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
* rtos/FreeRTOS: solve some conflicting usage of thread id.
1.
There are some RISCV-specific usage of thread_id, which has conflict with upstream.
Some adaptions are made in this patch, to make sure OpenOCD is sending a clear thread list to gdb.
2.
Use freertos_read_struct_value for xSchedulerRunning.
Change-Id: I001a88a0c6d8eac98a389c0217b4897f28124840
Signed-off-by: Chao Du <duchao@eswincomputing.com>
* fix typo.
Change-Id: Id6546cc74de44bbee7e44b7cb29b769a2f35ec4a
* correct the data type.
Change-Id: I28c7e111e569d94ba5f6e1ae21745ddb34d4dd12
* changes as per the review comment.
Change-Id: Ica4c705a8f2657700dc27e24790287ca802480fd
* another macro replacement.
Change-Id: Ia9330fed32d917cf87804051ba1b8d6ac42cfb7b
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
With this change, failures to resume a hart due to it not being halted
are more explicitly logged or reported as an error.
Change-Id: Ia55d8df85a908363d0f2140637ce1e47c1ab6251
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
This involves halting the target, which might have unintended side
effects, but when the debugger is connected software breakpoints must
trap to the debugger. Anything else is a terrible user experience.
Change-Id: I1f7bb610eeeb054cc3042dc6bcfc16589ce12a31
Signed-off-by: Tim Newsome <tim@sifive.com>
Tim Newsome
Evgeniy Naydanov
Erhan Kurubas
Antonio Borneo
Daniel Anselmi
Marc Schink
Mark Zhuang
Laurent LEMELE
Marek Vrbka
Parshintsev Anatoly
eolson
Chao Du