This enables gdb target description support by default, it will check that
this is supported by the active target.
Change-Id: Iea5a5b94c5e373af30dacb780020b79536caa1e3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1618
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Now that we support the target description format we do not need
these hacks anymore, we can now tell gdb what registers we support.
Change-Id: Ie774231d296420b35efcf708bc4435475c87ff5e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1617
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for the default gdb register description type "int" and "float".
When this is given to gdb it will use the bitsize to determine the reg size.
Change-Id: Iaeed594d1feece54044128eae1baff9858bdcae0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1622
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Half-word and byte writes using mwh/mwb has been completely broken since
bf71e34cbf, because it dispatched all writes, regardless of access size,
to target_write_buffer(), which uses as large accesses as possible.
Partially revert the commit by changing back to the correct write method.
Change-Id: I60731fc576bf4a076a7da02bee7879e121c21d17
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1628
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently we try and use MEM-AP packed transfers as much as possible for
8/16bit transfers. However not all targets support packed transfers, so
check before using.
Change-Id: I66256007f25ccd0c583f23db5acf6d1aa8b5e57d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1602
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
As autoconf is part of MinGW, it uses its root to find m4 files, pkg-config
should be installed accordingly.
Change-Id: I551797e61a3d044f751768bd7d57d8e26e7202cc
Reported-by: Tomáš Voda <Voda.Tomas@seznam.cz>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1630
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This updates README with all the "keywords" added since the initial
upstream submission (and finally fixes the typo in the beginning).
Change-Id: Ia071267246fe6afc19fc0bfcda83c4778e7ff5b1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Error was:
checking for library containing FT_GetLibraryVersion... no
configure: error: You appear to be missing the FTD2xx driver library.
Reason were two cases:
Case one:
The FTD2xx library uses clock_gettime() and in normal cases
the linker will find the function in the libc library. Most
(older) systems require the program be linked with the librt
library to use these (see man clock_gettime: Link with -lrt).
Case two:
You can rebuild the FTD2xx library (relink from the object
files) against the primary (system wide installed) libusb-1.0.
So you avoid mixed code (GPL with proprietary code) in the
FTD2xx library. In this case, the FTD2xx library provides no
private (linked in) libusb-1.0 functionality and require the
program be linked with the libftd2xx __AND__ the libusb-1.0
to resolve all the libusb-1.0 symbols.
Change-Id: Iaf9a35ab4257e37b98dccd47667378ad2a64b7ed
Signed-off-by: Stephan Linz <linz@li-pro.net>
Reviewed-on: http://openocd.zylin.com/1614
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Usage:
export LIBUSB1_SRC=/path/to/libusb-1.0
export OPENOCD_CONFIG="--enable-..."
cd /work/dir
/path/to/openocd/contrib/cross-build.sh <host-triplet>
For static linking, a workaround is to
export LIBUSB1_CONFIG="--enable-static --disable-shared"
All the paths must not contain any spaces.
Feel free to comment or update this patchset with improvements.
Change-Id: Ib3b4970117f13a6140a1eddc493d324a52364519
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1531
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Force the libusb-1.0 include dir to be treated as a system include path
which suppresses the cast-align warnings otherwise failing the build on
some platforms.
Change-Id: I738cfd793052b8772731d2feeef968ee893bd4bd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1534
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This unifies the way the USB adapters are handled, and enables them
automatically whenever possible (until explicitly disabled). If an
adapter is explicitly enabled but can't be built, abort the
configure.
Also add infrastructure for generic handling of adapter drivers in
configure and print a summary of the configuration results after
finishing.
The m4 quoting is as conservative as I could get it, and seems
appropriate.
Change-Id: I1655691e5ea0d8eb9e3f67830b96992ffe33640a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1475
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
An alternative approach to show how much cleaner the pure pkg-config
way is.
This changes the discovery procedures for libusb-1.0 and libusb-0.1,
making them depend on pkg-config being properly installed and
configured, including the necessary build host configuration for the
cross-builds (see
http://www.flameeyes.eu/autotools-mythbuster/pkgconfig/cross-compiling.html)
It should make it possible to compile OpenOCD without changes and
extra effort on GNU/Linux, FreeBSD users would need to supply a .pc
file for their libusb implementation or add LIBUSB1_LIBS and
LIBUSB1_CFLAGS to the configure environment.
Change-Id: I826e378dd1e0d101a549a573b2c63212a7e00b64
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1467
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
This is an attempt to bring the README files in line with the current
status of the OpenOCD development.
- remove some obsolete information and duplicated instructions
- reword some statements
- restructure in a way more appealing to a regular user
- add a supported hardware list to allow a potential user to determine
if his/her usecase is covered by a freetext keyword search through
the document
- Add OSX notes (courtesy GrizzlyAdams and inca)
Since most ftdi-based adapters are now covered by the ftdi driver, I
think it's ok to remove some of the libftdi/ftd2xx instructions, the
few users who still need them should refer to upstream docs instead.
I'm not sure if README.Windows should come with the DOS line endings,
but i'd expect many windows users to use their silly notepad to view
it, and notepad ignores LF apparently. (Decided to use LF anyway.)
I understand discussing and reviewing such a massive README change is
a somewhat demanding task but I feel it's a necessity to move forward
maintaining proper documentation.
Change-Id: Idfde3014c72dd5c32ad292ee1ab205322e51a138
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1503
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
.soft_reset_halt is not necessary for nds32 target.
Remove the dependency.
Change-Id: Ic3b126d6c7eb995583a661b762627e736222fcaa
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1612
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As GDB uses file-I/O protocol to access memory, use DMA to access
if no DCache. This commit improves the performance of Andes
Virtual Hosting.
Change-Id: I36bb2154b9f497fc4237625836cf8c7115330a60
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1580
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Modify handle_nds32_memory_access_command: do not use DCache
setting to block user's setting.
Change-Id: I2d33f893773e2a2e3e2f26edde5938ef5902609d
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1579
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If multiple read watchpoints are hit at the same time, report
any one of these hit watchpoints.
Change-Id: I8d4439aa80e4b62bb7d48bbdc0450920e2008a2e
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1576
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do not turn on/off polling as leave/enter debug mode.
Enable polling after gdb attached, and disable polling
after gdb detached.
Change-Id: Id64459b86f44937af7ea5ccfe2cd13e31732eecf
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1574
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
1. gprof uses 2-bytes as minimum bucket size.
2. As user wants to use gprof --sum to summarize multiple
profiling data files, the range MUST be the same.
Add new arguments to specify profiling range.
Change-Id: Ie7e6afa6a4d82250e2d194a0eed2b428c1479ea1
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1572
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Profiling could be target-specific. Add .profiling interface
to target_type.
Change-Id: Ic0eea9db742971db1350a474fbbb5ed24565922b
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1571
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
I do not know what is the reasonable number of buckets.
If there are enough buckets, the result will be accurate.
I propose increase the maximum number of buckets to 128K.
If the size of program text section is less than 256KB, every
two bytes will be occupied by one buckets.
(The minimum size of one buckets is 2 bytes in gprof implementation.)
Change-Id: If9147743cefdc36f40f21e6dc73b9b28f28c9e1e
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1608
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
1. high_pc should be (maximum sample + 1) (Refer to gprof source code)
2. bucket index should be
sample offset
--------------- x (number of bucket)
sample range
For example, if minimum sample is 0 and maximum sample is 5
and the number of bucket is 3.
a = sampled_address - 0
b = 3
c = 6
(a, b, c refer to source code variables)
sampled_address = 0, => a = 0, => bucket_index = 0
sampled_address = 1, => a = 1, => bucket_index = 0
sampled_address = 2, => a = 2, => bucket_index = 1
sampled_address = 3, => a = 3, => bucket_index = 1
sampled_address = 4, => a = 4, => bucket_index = 2
sampled_address = 5, => a = 5, => bucket_index = 2
Change-Id: Ia9fa0e4d9c7183e3e9d7ceaf73e63729f07aa2ce
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1607
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change variable name 'length' to 'numBuckets'. It is more readable.
Change-Id: I913cba0746f887adf6da401a46cd5e9ea88d2c6d
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1606
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In GDB connected to OpenOCD there is a command "monitor gdb_sync" which makes
next stepi command to be ignored while GDB still will get an updated target
state. This command sets gdb_connection->sync field to true to notify that stepi
should be ignored. This field is set to true for all new connection and is set
to false after first "continue" command. However if first resume command is
stepi/nexti then it will be ignored and result will confuse GDB client, it will
report that target received signal SIGINT. This patch sets this field to false
for new connections, thus stepi/nexti will work properly when it is a first
resume command.
Change-Id: I7c9ebd69c3dc35f3e316041aa99f4e9d3425c0b6
Signed-off-by: Anton Kolesov <akolesov@synopsys.com>
Reviewed-on: http://openocd.zylin.com/1587
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Keep the promise and ensure there're at least 3 bytes available after
the current position.
This eliminates the errors reported by Valgrind.
Change-Id: I1d0640e904c750eed808b2b4caf419b4d7619845
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1615
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Rewrite the target_*_buffer_default to generate as large accesses as
possible while maintaining natural alignment.
These versions are easy to extend to generate 8-byte accesses to support
64-bit targets, although it requires some conformity from all target
implementations (i.e. they need to refuse unsupported access sizes with
some defined error code, so we can try again with a smaller one).
Change-Id: I00ddcbb1d2fd33f9f8b99cb448cc93505a2421fc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1221
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only remaining user is arm7_9 so remove it from the target API and add
it to struct arm7_9_common to support all its variants with minimal
changes. Many of the variants are likely not correct in the cache/mmu
handling when the bulk write is triggered. This patch does nothing to
change that, except for arm946e, where it was easier to do what might be
the right thing.
Change-Id: Ie73ac07507ff0936fefdb90760046cc8810ed182
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1220
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
remove clang warning - "Argument to free() is the address of a global
variable, which is not memory allocated by malloc()".
Change-Id: I015273eafc9644207684b363434c6ae8149bfcde
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1613
Tested-by: jenkins
We already set cpsr in armv7m_build_reg_cache, so lets use it for all other
accesses to this field.
Change-Id: I19b3b21ecf1571bbea12e1be664845e6544f6fa1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1539
Tested-by: jenkins
Make sure the target support target requests before we enable any receivers.
Change-Id: I8ce42922eaff76fb5e7a114da716f2a6585a6ab5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1536
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Let the default handler issue an unsupported warning rather than using
empty handler routines that may/may not issue a unsupported warning.
Change-Id: Iafe3e45146981a4cfae39771c3ab7370ac86da48
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1535
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Adds a flash driver for Nuvoton MINI51, MINI52 and MINI54 microcontrollers.
At the moment, it only supports the erase and write operations.
These microcontrollers have a 4 / 8 / 16 KB APROM for application code and a
2 KB LDROM for bootloaders. When the MCU has booted off the APROM, the LDROM
isn't mapped in memory but can be programmed, and the other way around.
This means that the ARM core is typically rebooted for programming. After a
successful write or erase operation, it is rebooted again, using the initial
boot source.
This driver only supports programming the APROM.
This driver is a pure JTAG implementation, it doesn't use any SRAM.
I've tested it on a MINI54ZAN microcontroller using an ST-LINK/V2. With the
microcontroller running at the default clock frequency of 22.1184 MHz, speed
seems to be around 1.1 KB/s.
Change-Id: I180889c55af9fb5614cd99a953b755baba14288a
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/1546
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds a driver for the jtag_vpi server [1]. This server is
now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC).
The jtag_vpi server provides an interface between OpenOCD and a simulated
core.
[1] http://github.com/fjullien/jtag_vpi
Change-Id: I717b72cace4845f66c878581345074f99002e21a
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Spencer Oliver
Andreas Fritiofson
Paul Fertser
Stephan Linz
Nemui Trinomius
Hsiangkai Wang
Anton Kolesov
Cosmin Gorgovan
Franck Jullien