The ref manuals for the stm32f2x (RM0033 Rev4) and stm32f4x (RM0090 rev1)
are unclear to the address of the flash size register (F_ID).
According to contacts @ ST this is the correct address, the manuals will be
updated in due coarse.
Change-Id: If9fb83b3100458d17038cf27c2b23355e1dc5a9e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/448
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
Added the file imx28.cfg to the target directory
Added the file imx28evk.cfg to the board directory
Change-Id: I02a74a03f3773892f830d13660ffdded34f3261d
Signed-off-by: James Robinson <jmr13031@gmail.com>
Reviewed-on: http://openocd.zylin.com/428
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds init_board concept information to OpenOCD manual.
Additionally a link from init_targets chapter to new chapter about
init_board is added.
Change-Id: I09b9aaa1cf68b94f35701224f641cae9811a5bcf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/440
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32L ref manual (RM00038 Rev5) states the SW-DP id should be 0x4ba00477.
The correct value from silicon is 0x2ba01477 - the typo has been confirmed by ST.
Change-Id: Ie35a1f13dc5dedc1b148fb219c6974bfa48b537c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/441
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This enables the user to override the transport used for st-link.
If JTAG is selected it will also change the default id used to the JTAG id
rather than the SW-DP id.
Change-Id: I4fe352e4932e2f4ec278168e99ba2d2d50fd850a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/443
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This adds init_board procedure that behaves exactly the same as
init_targets - it can be overriden by "next level" scripts. This
procedure is executed after init_targets, allowing common stuff (jtag
chain, memory, flash, ...) to be configured in target script (via
init_target) and leaving rest (like additional memory, reset
configuration, reset-init handlers, ...) to be done in init_board.
This makes init_targets scheme more complete and easier to use - current
board scripts will not need new init_targets, because everything can be
"packed" in init_boards. Moreover it solves the problem of variables
being set in init_targets (executed after init), which were not
accessible by "linear" scripts (parsed before init). All that has to be
done is to enclose all code in board config file in init_board
procedure.
Change-Id: I0736b1ff9873a687966407d62b58ccf29a8e597b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/427
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Add a note to the docs about the original stlink being broken under linux.
Change-Id: Ib440d78e5c7d31eeace99f611a76fcf701bfb8bc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/433
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Make _TARGETNAME variable global so it could be used by scripts sourcing it.
Change-Id: Iaf1c3b53875734658b1b8f136c9bb958988b56bf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/421
Tested-by: jenkins
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This issue was caused by uncrustify not correctly converting the doxygen
comments.
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Change-Id: Ie6dc3b057a08603b670cb27312e5f0d989426e6c
Reviewed-on: http://openocd.zylin.com/431
Tested-by: jenkins
These checks are specific to linux kernel.
Change-Id: Ia9b837b5609922a897822f1d55f96f04c0f1f838
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/424
Tested-by: jenkins
We may enable this again - but at the moment is causing extra issues
with reformatting the codebase.
Change-Id: I5a2aaaa32ad784e011dff3079ff45501452c1819
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/414
We may enable this again - but at the moment is causing extra issues
with reformatting the codebase.
Change-Id: Ic64310a20605a0ef3206caa15c8e6c8ee655bfda
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/413
Tested-by: jenkins
This config has been updated for 0.59
Change-Id: If0dc87dd5de052c1228743a196a3198dbd4bc279
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/406
Tested-by: jenkins
This patch add a validation for the supported jtag api version.
Change-Id: I0b51350e58e351d6662f4039c0a9e9d0d79ba4ec
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Correct the offset to the read pointer when clearing it on error.
Also restrict the instruction set to armv6-m so the flash driver can be
used on Cortex-M0 parts with the same flash controller.
Change-Id: I380f9dabcc41fb6e4d43a7e02f355e2381913f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/399
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Replace the big stack-allocated buffer with a much bigger heap-allocated.
There was no explanation for the apparently arbitrary chunk size, and
performance was improved by increasing it, leveling out at about 4k.
Change-Id: I3b06d4469092ec8d89d0ce05bff0b7cf213c5062
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/404
Tested-by: jenkins
Reviewed-by: Marti Bolivar <mbolivar@leaflabs.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This patch test the device version and differentiate between
v1 and v2 devices.
Change-Id: Ie79bf2c5534211493b004329fb6d5b9d4ea5453b
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/396
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add jtag support to the stlink driver add
two new transport types, JTAG and SWIM.
Change-Id: I7089d74250330be5c6a01c24066307641df7d11e
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/393
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This only effects the older Stellaris LM3S811 kits (rev B and below).
Change-Id: Ie068cce7748fede9e7113ea63a69c96222c809fa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/401
Tested-by: jenkins
for some reason the following commit was incorrect
769064de4b
Only the Sandstorm and Fury class should write this register.
Change-Id: Ie18f1da6e9b59fb99cca47aa93c7f2fee447ccea
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/400
Tested-by: jenkins
For example, when blocks 2 and 3 were erased, openocd reported "erased blocks 2 to 4". That should be "2 to 3", I think.
Change-Id: Icece63dedd3dd931b70fa73616819a19572e39de
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/385
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SPAS register (OOB size) is left wrong after reset with respect to 2KiB page NAND chip. That will lead to ECC errors after 'reset halt'.
Change-Id: If5a4685cb8d6be35879453951611ef1059da219c
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/384
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch is based on Erik Ahlén's work on i.MX35 NFC support. Basically it redefines the CCM.RCSR register which is in a different address in i.MX25.
Change-Id: Ia6faf9cb5efae5e564b72ef9a9b7c7f8bfde3ce0
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/383
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
stellaris_set_flash_timing should only be used for Sandstorm and Fury
device classes.
Change-Id: Ib5eff9d954c039f2c5726a8ecc3ee45d1694cfd3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/389
Tested-by: jenkins
read the target class during probe and save for later use.
Change-Id: Ib3ad20edc7d206b7f434bdcc6b947e6a5f06dd1f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/388
Tested-by: jenkins