The new Microchip (former Atmel) series powered by Cortex-M4 looks
very similar to older M0+ powered SAM D2x at the first sight.
Unfortunately the new series differs a lot in important details.
NVMCTRL has different register addresses, moved important bits
and even changed binary command set. An universal driver for all SAM D/E
would be very complicated. That's why a new driver was derived.
Tested on Microchip SAM E54 Xplained Pro kit (board cfg included).
Adjusted for the restructured dap support.
Checked by valgrind and clang static analyzer.
Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4272
Tested-by: jenkins
Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
stm32x_write_options() uses stm32x_write_block() at STM32_OB_RDP address.
The change eliminates subtracting bank->base (and later adding it back).
Change-Id: Icdd24afc7178b814be58e6033d4b93fdfb2d2a16
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4859
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Change-Id: I1e9e62979c4629c8ba1d5ae89ca7392259969eb6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4858
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Stepping in the maskisr auto mode sets breakpoint to step over interrupt
service tasks. If the device has FPB rev 1, setting hard breakpoint
is impossible on address over 0x1fffffff.
Use soft type breakpoint for adresses over 0x1fffffff if FPB is rev 1.
This may eventually fail if the code memory is not writeable, but there
is nothing to do in such case.
Change-Id: Ibdeeb506903a35d550b64f82c24c37a668de62b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4857
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
samr34/r35 combine SAML21 and SX1276 (lora transceiver). This one was found on
xplaned pro evaluation kit. Ids for other r34/r35 chips are apparently not yet
documented.
Change-Id: I4054dd56ea53c9bae8d17abd5a3e4e65e1b9c8b1
Signed-off-by: Guillaume Revaillot <g.revaillot@gmail.com>
Reviewed-on: http://openocd.zylin.com/4872
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The functions dap_to_jtag() and dap_to_swd() have been introduced by
3ef9beb52c ("ADIv5 DAP ops switching to JTAG or SWD modes") in
arm_adi_v5.c by using the JTAG queue only.
Later, in 6f8b8593d6 ("ADIv5 transport support moves to separate
files") the functions has been moved in adi_v5_swd.c and adi_v5_jtag.c
but keeping the dependency from JTAG queue.
The functions does not work if the current transport is not JTAG.
Move back the functions in arm_adi_v5.c, replace the input parameter
"target" with "dap", use the transport to detect if the JTAG queue is
present, in case of SWD transport use the proper method, for other
transports report error.
Reuse the ADI v5 sequences already present in jtag/swd.h.
Also, OpenOCD does not support switching to another transport after
the initial selection, so do not change DAP's ops vector.
Change-Id: Ib681fbaa60cb342f732bc831eb92de25afa4e4db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4852
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Treat ARM_MODE_SYS like all other Aarch32 processor modes,
except for the special case of missing SPSR.
Change-Id: I60b21703659b264f552884cdc0f85fd45f7836de
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4494
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
A target created after init lacks target_init_one() call
and is not added to gdb targets.
Steps to reproduce:
- start OpenOCD with a dap target
- connect by telnet
target create ap0.mem mem_ap -dap $_CHIPNAME.dap -ap-num 0
reset
Segmentation fault is rised because target->check_reset is NULL.
Change-Id: I2a62f3b450e4db3005c7041a22fb8f952e68c3b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4842
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command mode was checked only for simple type of commands.
Native commands (handled by jim_handler) was treated as
they had mode COMMAND_ANY
Change-Id: Iab1d8cbb0b8c6f6b9f3cf942600432dec9a703ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4841
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 44009186cf added logging
of failed cmd name but it used c->name only. It might be confusing:
Debug: 244 105 command.c:644 run_command(): Command 'init' failed with error
code -4
User : 245 106 command.c:711 command_run_line():
Debug: 246 107 command.c:644 run_command(): Command 'init' failed with error
code -4
The command on line 244 is 'dap init'
Use full name of cmd including parents.
Change-Id: Iff131ce6454ef70b353ce1bc6d0a480b92820545
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4837
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Without this change TARGET_DEBUG_RUNNING changes to TARGET_RUNNING
after adapter_poll()
Change-Id: I1c965a43527b50fa723d78fb6eae56585a7ede03
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4820
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
All the commands in OpenOCD have been inspected and have the
command mode initialize, apart for two of them.
This is not critical, because the uninitialized value (0) is
equivalent to the enum COMMAND_EXEC, that is also the correct
value for the two mentioned commands.
To keep the code consistent, initialize the command mode to
COMMAND_EXEC.
Change-Id: Iaf043364cbd1005418d787ed045a3ec653612382
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The original script was broken by changes to the Cortex-A code. The
recent introduction of the mem_ap target provided a new mechanism to
allow the script to be fixed. This also adds an example board script
for the ADSP-SC584-EZBRD.
Change-Id: I36bc1ac6b6c036539f4175f1e65223ba10a35355
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4855
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While connecting under reset, use the already defined macro
SWJ_PIN_SRST to assert the srst pin.
Change-Id: Icebed462c0fe8f8c15f6522dc56625aa580b8858
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4846
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add RTOS task awareness for Chromium-EC. Currently
only supports ARM Cortex-M0/M3/M4 based targets.
No new Clang Analyzer warnings.
Change-Id: Iea56fcb1be220e2437613922879b63d6e553703d
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4685
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The xilinx_ultrascale.cfg target is actually the configuration for a
ZynqMP, which is a combination of an UltraScale+ FPGA core and a quad
core A53. Update the filename/comments to reflect this, and include
the tap IDs for all known FPGA cores for this part.
Change-Id: I70dfcc99861a482b83b6a795e83021d9cf1fe047
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4850
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The encoding of BKPT instruction is 0xE12###7#, where the four '#'
characters should be replaced by the 16 bits immediate value.
The macro uses an incorrect shift amount, thus the immediate value
is not properly coded and bits 20~23 of the opcode could get
corrupted.
Fixed by using the proper shift amount.
Change-Id: I32db8224ab57aad6d3b002f92f9f259056593675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4854
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Fix the SWD line reset sequence accordingly to Arm specification IHI
0031E that requires at least 2 idle clocks after the 50 clocks with
SWDIO high.
Fix the value of the activation code in the (currently unused)
sequence dormant-to-SWD.
Make each sequence's length multiple of 8, so it is compatible with
adapters that have such limitation (e.g. buspirate) and try to split
and comment each part of the sequence (when possible keep each part
byte aligned, inspired from commit 3ef9beb52c). This slightly
increases the sequence length but does not impact run-time
performance because these are rarely used sequences.
Add the missing sequence dormant-to-JTAG and JTAG-to-dormant, not
used yet.
On devices that implements the dormant state, IHI 0031E deprecates
the direct switching between SWD and JTAG, and recommends using a
transition through dormant. This is not implemented.
Change-Id: Iad18c0e736cfd9366be175d22658d664b0c61eab
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4851
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This hardware id is e.g. used by the Insight SiP ISP1507-AX.
Change-Id: I82568d292f9882372ab061d8e3e36906b0cc5882
Signed-off-by: Mirko Vogt <mirko.vogt@sensorberg.com>
Reviewed-on: http://openocd.zylin.com/4845
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This patch covers the fact that cortex_m could be resumed externally by
Cross Trigger Interface or by direct write to DHSCR ...
To reproduce:
- halt the target
- then run the core through DHCSR (mww 0xe000edf0 0xa05f0001)
=> this resumes the core, but target state in OpenOCD remains HALTED.
Change-Id: Ifa1ae18645bfeb863acc78a039bbf04873fd78fe
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4817
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cortex_a_debug_entry and update_halt_gdb are called in two consecutive
conditions which are complementary, so externalizing the common code
makes the conditions' body lighter
With the removal of LOG_DEBUG(" ") since it does not look too informative
Change-Id: I0c54e413619576bb3af164f2dcf256c5a862c5fd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4832
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
If malloc fails in __command_name, the following strcpy will
segfault, thus preventing __command_name to return.
The actual calls to command_name() implement the correct check
for the NULL pointer, but propagate error -ENOMEM, that is not
an error value coherent within OpenOCD. Plus, in one case it
overwrites an already detected error.
Check the pointer returned by malloc and, in case of failure,
issue an error message and return the NULL pointer.
Let the caller of command_name() to keep the already detected
error or to return ERROR_FAIL in case of end of memory.
Change-Id: I151a24569409777dd5bc09a3daf5dba2b8e2829b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4838
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio.
Change-Id: If5b3c618097b71dfe7fcf988fb3c1499ae03a6d5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4833
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Valgrind and Clang Static Analyzer have no complaints about this change.
Change-Id: I7757615ec52448372bdc57729cdf97c7016d97e8
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4656
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commands to stlink devices are typically comprised of multiple
transactions with each transaction completing before moving to the next.
This change allows for multiple USB transactions to be issued at once
followed by a check that all transactions completed successfully. This
improves performance on some machines where there is a large turn-around
time between USB transfers such as is seen on some virtual machines.
This change is only supported when compiled with libusb1 as libusb1
supports and asynchronous interface.
Multi-transaction queueing introduced in this change paves the way for
improving speed of other transactions in the future such as memory and
register reads where multiple USB transactions in succession are
required to complete a command. Multiple USB transactions can be
submitted at once using jtag_libusb_bulk_transfer_n function.
Change-Id: I924e049217a789ef445b14e00aa1983576970fbf
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4484
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When few adapters of the same type are in use, the serial string is
the way to select the right one.
Currently a serial string that does not match any of the connected
adapters will just fail the open, without specific information to
track the issue.
Add a specific message to highlight that the open failure is caused
by a serial mismatch.
Change-Id: I5cb77f1045cc746e532d395b2e5ced40a23ab638
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4701
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Where possible, keep the same style for returning error.
Change-Id: I3a04220c0b9f129a36e9fe83038b7c19dd57fe61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4699
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d1b7437633 fixes libusb1 to
return OpenOCD error values instead of negative errors in Linux
kernel's style.
The same fix should be applied to libusb0 too.
Fix return value of libusb0 to uniform it to OpenOCD style.
Change-Id: I68478c29c91c6be720074f58c432fe51477e03ed
Fixes: d1b7437633 ("libusb: return oocd error values")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4698
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
aarch64-linux-gnu-gdb 8.2 uses "aarch64" as default architecture,
but also supports the value "aarch64:ilp32" and all the values
supported by arm-none-eabi-gdb.
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for aarch64 target to "aarch64".
Change-Id: I63e9769f47d8e73f048eb84fa73e082dd1c8e52c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4755
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
arm-none-eabi-gdb 8.2 uses "arm" as default architecture, but also
supports the following values: "arm_any", "armv2", "armv2a",
"armv3", "armv3m", "armv4", "armv4t", "armv5", "armv5t", "armv5te",
"armv5tej", "armv6", "armv6k", "armv6kz", "armv6-m", "armv6s-m",
"armv6t2", "armv7", "armv7e-m", "armv8-a", "armv8-m.base",
"armv8-m.main", "armv8-r", "ep9312", "iwmmxt", "iwmmxt2", "xscale".
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for all arm targets to "arm".
Change-Id: I176cb89878606e1febd546ce26543b3e7849500a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4754
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
The gdb patches for stm8 are still not merged in the official
repository and are temporarily hosted in
https://stm8-binutils-gdb.sourceforge.io/
The latest patch set
stm8-binutils-gdb-sources-2018-03-04.tar.gz
define only one possible value ("stm8") for this architecture; it
can be displayed typing "set architecture " followed by a TAB for
autocompletion in gdb for stm8.
Set the gdb architecture value for stm8 to "stm8".
Change-Id: I643ceba662de46cecf061d1dc672b9178a077f1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4753
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
xPSR.T sets the processor to Thumb mode when set to 1. ARMv7-M only
supports execution of Thumb instructions, so it must always be set to 1.
If xPSR.T is set to 0 on armv7m, a usage fault is generated when a
instruction execution is attempted.
On armv7m, issuing a reset causes the vector table to be examined. PC
and xPSR.T are loaded from the vector table at byte offset 4. xPSR.T is
taken from the least significant bit this value, PC from the remaining
bits. This occurs even with `reset halt`, as the reset itself causes
this load to occur without the execution of any instructions.
As a result of this, following a reset with a "bad" value programmed in
the vector table, openocd would be unable to run algorithms on the
target, as running them would immediately result in a usage fault due to
xPSR.T being unset (0).
Allow algorithms to run regardless of the content of the vector table by
explicitly setting xPSR so that xPSR.T=1 prior to executing an
algorithm. One can think of this as openocd more closely emulating a
reset or branch instruction in executing it's algorithms.
Ticket: https://sourceforge.net/p/openocd/tickets/203/
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: I4dc3427ab195d06c3fd780ea768027fefccc4c28
Reviewed-on: http://openocd.zylin.com/4658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Agama family of devices (CC26x2/CC13x2) required an
additional bit to be set when adding the core's TAP into
the scan chain. The cancel reset bit 0x10000 tells the
ICEPick to take the bus out of reset so that the other
bits will take effect. This bit is a NOP on other devices
and ICEPicks, so the change shouldn't adversely affect
other devices.
Change-Id: I9245eef0936ea7eea28ae84ab5e8ce05fa63af40
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The XDS110 stand-alone version has the ability to supply
voltage to the target board via it's AUX FUNCTIONS port.
Added command to enable setting the voltage on the XDS110
stand-alone.
Change-Id: I2f21c4a3d15ed99e649f3a83973c5e724c4bfeb6
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4793
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The fact that one needs to always push contributions to a single
remote reference (refs/for/master) might seem odd to people unfamiliar
with Gerrit. GitHub, for instance, hosts personal repositories where
developers typically create topic branches for each contribution and
use a proprietary mecanism to request a review (the "pull request").
More generally, one normally does not expect to be able to push
non-fast-forwarding stuff to a remote branch.
This commit adds a clarifying note to the patch guidelines.
Change-Id: Ia750b815b82b18e92b6109c07f451000dcbecf9b
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-on: http://openocd.zylin.com/4806
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
refs/publish/master is deprecated and gives a warning in newer Gerrit.
Replace with refs/for/master.
Change-Id: I56871cc6e80c014ba81f4458230cd67dc318ecb3
Suggested-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-on: http://openocd.zylin.com/4810
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Longest erase all FLASH for nRF5 series is 295.3 ms for nRF52832.
Timeout period now is set to 340 ms (295.3 + 15%)
Change-Id: Iae00ed7b634f111b9798db11e35e4e066d4aaa95
Signed-off-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-on: http://openocd.zylin.com/4822
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this permits the full control of CTI from config files
Change-Id: Ia27ac8e12e08ec72da05f26dcbd81d24fa1a0f6f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4815
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
w600 is a wifi soc from winner micro(www.winnermicro.com).
Change-Id: Ib8ccd6e52baefca6547fb97d29db75db0ee73948
Signed-off-by: Simon Qian <versaloon@simonqian.com>
Reviewed-on: http://openocd.zylin.com/4801
Tested-by: jenkins
Reviewed-by: yichen <wdyichen@wdyichen.cn>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target configure -work-area-xxx calls target_free_all_working_areas()
and sets the desired new parameter. Without this change the working area
does not get reallocated if it has been allocated before.
target_free_all_working_areas() results in work area containing one block
marked as free.
Completely free working area in target_free_all_working_areas()
Change-Id: I79c681082f32f2a96a2b40eb3b8751e427549693
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4797
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tomas Vanek
Guillaume Revaillot
Antonio Borneo
Matthias Welwarsky
Peter Lawrence
Moritz Fischer
Jonathan McDowell
Mirko Vogt
Tarek BOCHKATI
Severin Junker
Tim Newsome
Austin Phillips
Cody P Schafer
Edward Fewell
Jerome Forissier
Rod Boyce
Oleksij Rempel
Jānis Skujenieks
Tarek BOUCHKATI
Jean-Christian de Rivaz
Simon Qian