Previous to this version the code of handle_flash_probe_command would
probe a bank twice: first time by auto-probe through a call to
flash_command_get_bank and second time by calling the probe function
directly. This change adds a flash_command_get_bank_maybe_probe wich
is a more generic version of the flash_command_get_bank, that would
allow commands to decide whether auto-probing should be performed or
not.
Change-Id: If150ca9c169ffe05e8c7eba36338d333360811e3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2093
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The error message (with the usage field unpopulated) looks like this,
obviously missing at least a space before Usage:
Error: 'fm3' driver rejected flash bank at 0x00000000Usage (null)
Change-Id: I2a625676e784d02942823f972a201f7f4f810c68
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2161
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This eliminates most of the warnings reported when building for
arm-none-eabi (newlib).
Hsiangkai, there're many similar warnings left in your nds32 files, I
didn't have the nerve to clean them all, probably you could pick it
up.
Change-Id: Id3bbe2ed2e3f1396290e55bea4c45068165a4810
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds support for setting the default value used when padding image
sections. Previously 0xff was used but some targets have an erased value
of 0x00.
Change-Id: If3df6fea3abf95b09daa3ff7be362acf991070ce
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1635
Tested-by: jenkins
Remove lots of no-op or dummy info function implementations and check if
it's implemented before invoking it.
Change-Id: I2144dad6a84a80359bb13a8a29a4614387e4c135
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1642
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reorder to allocate all memory after COMMAND_PARSE_NUMBER call.
This removes a clang warning about un-released memory
Change-Id: I8dbeb664a6467077157015bd879bc0aefc5e8614
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/776
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This makes use of the newly introduced usage field in the flash bank
structure.
Also remove the assertion if usage field is null and
lets print a DEBUG_LOG message instead.
Change-Id: I384bf0e2c444fcc99deef73aec9ef01149a91c76
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/391
Tested-by: jenkins
Do not propagate error number to user. This is for internal
programming purposes only. Error messages to the user is
reported as text via LOG_ERROR().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The flash bank name is a required element in adding flash banks,
however other than looking at the config file there is no way of
getting the name used in openocd.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
when a write/unlock/erase failed during write_image, then
an error was not propagated back up so e.g. flash write
image from tcl scripts would not throw an exception.
Also flash filling speed was printed even when the
operation failed. Output is now less confusing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Change download rate messages about kibibytes from "kb/s" to "KiB/s" units.
See: http://en.wikipedia.org/wiki/Data_rate_units
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
flash cmds can now be passed either the bank name or the bank number.
For example.
flash info stm32.flash
flash info 0
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
There are a million reasons why cached protection state might
be stale: power cycling of target, reset, code executing on
the target, etc.
The "flash protect_check" command is now gone. This is *always*
executed when running a "flash info".
As a bonus for more a more robust approach, lots of code could
be deleted.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The command "flash bank" has updated syntax.
Add the mandatory parameter <target> to the usage message
that prints in case of error.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes bug that prevented users from specifying a base address of
0x80000000 or higher in image commands (flash write_image, etm image,
xscale trace_image).
image.base_address is an offset from the start address contained in
the image file (if there is one), or from 0 (for binary files). As a
signed 32-bit int, it couldn't be greater than 0x7fffffff, which is a
problem when trying to write a binary file to flash above that
address. Changing it to a 64-bit long long keeps it as a signed
offset, but allows it to cover the entire 32-bit address space.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.
Add TODO list entry re full support for NAND/NOR bank names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's currently allocating a big buffer but writing it out in
units of sizeof(host's pointer) ... sub-optimal.
Plus fix a couple minor coding style goofs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the existing 'flash banks' implementation as 'flash list', and
replace the broken 'flash_banks' TCL wrapper with a new command handler.
Adds documentation for the new 'flash list' command in the user guide.
Splits the exec mode commands out of flash.c into the flash/nor/ files.
The routines used by these high-level commands are moved into nor/core.c,
with their internal declarations placed in nor/imp.h.
Fixes distribution of <flash/nor/core.h> header.
The newly moved flash TCL routines access the internals of the module
too much. Fix the layering issues by adding new core NOR flash APIs:
<flash/nor/core.h>:
- flash_driver_find_by_name() - self-descriptive
<flash/nor/imp.h>:
- flash_bank_add() - encapsulates adding banks to bank list
- flash_bank_list() - encapsulates retreiving bank list
This allows the externs in flash/nor/imp.h to be removed, and
these mechanisms may now be re-used by other flash module code.
Moves the top-level 'flash' command handlers into flash/nor/tcl.c,
with flash/nor/imp.h providing an internal implementation header
to share non-public API components.
Andrey Smirnov
Paul Fertser
Spencer Oliver
Andreas Fritiofson
Øyvind Harboe
Rodrigo L. Rosa
Spencer Oliver
Jon Povey
Antonio Borneo
Bradey Honsinger
David Brownell
Freddie Chopin
Zachary T Welch