TUMPA Lite is a cheap FT232H-based breakout board, without any
buffering. It also lacks series resistors so for some targets
(especially when not using ridiculously short wires) one needs to add
about 47 Ohms in series on every high-speed line.
The SRST line is connected directly to the FT232H too.
Real-life tested (including SRST and TRST).
Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1918
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These kits feature a CMSIS-DAP compliant debugger and so have been added
as part of the pending support.
Currently the flash drivers for the L8 and D20 are wip.
One issue this implementation of CMSIS-DAP raised is that it supports
512byte HID reports, however using the current HIDAPI we have no cross platform
way of querying this info. Long term we plan to add this support to HIDAPI.
Change-Id: Ie8b7c871f58a099d963cd71a9f8a0105a38784e9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1625
Tested-by: jenkins
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
Fix following warning message logged by udev at start
udevd[421]: SYSFS{}= will be removed in a future udev
version, please use ATTR{}= to match the event device,
or ATTRS{}= to match a parent device, in
/etc/udev/rules.d/95-openocd.rules:81
Change-Id: I6de935c13a3327e3d718c110f97d19b9847ceca5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/552
Tested-by: jenkins
Reviewed-by: Luca Bruno
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This corrects permissions on the FTDI chip on the xds100v2 debugger
enabling normal users to access it.
Change-Id: I0f6618692ebdee6284eee28f9e612e68782c4d78
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-on: http://openocd.zylin.com/188
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Most serial adaptors are identified by udev with SUBSYSTEM=tty and
without DEVTYPE. This patch fix udev rules to work with any listed
tty-based adaptor. It has been tested with a FTDI-based Bus Pirate.
Signed-off-by: Luca Bruno <lucab@debian.org>
New versions of udev (148+) emit the following warnings:
udevd[425]: BUS= will be removed in a future udev version,
please use SUBSYSTEM= to match the event device, or
SUBSYSTEMS= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:1
udevd[425]: SYSFS{}= will be removed in a future udev version,
please use ATTR{}= to match the event device, or
ATTRS{}= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:4
udevd[425]: SYSFS{}= will be removed in a future udev version,
please use ATTR{}= to match the event device, or
ATTRS{}= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:7
...
See also http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=560141
[dbrownell@users.sourceforge.net: add IDs for Stellaris ICDI, Olimex Tiny-H]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Paul Fertser
Spencer Oliver
Antonio Borneo
Ulf Samuelsson
Kyle Manna
Uwe Hermann
Spencer Oliver
Eugeniy Meshcheryakov
Luca Bruno
Michael Trensch
Johannes Stezenbach
zwelch
oharboe
duane
kc8apf