General rule, this is all board-specific and doesn't belong
in target config files. Some of these were just cosmetic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Here's a patch for the double-reset problem on STM32. I've tested
downloading and debugging with GDB and Eclipse, and everything seems
to work fine.
This effectively sets reset_config to none. trst_only would also
be ok, but that's better left to a board configuration file since
not all boards wire it up.
The NVIC is used to trigger reset, which at least on this chip also
pulses nSRST so the whole system does get rest -- exactly once.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's been about a year since these were deprecated and, in most
cases, removed. There's no point in carrying that documentation,
or backwards compatibility for "jtag_device" and "jtag_speed",
around forever. (Or a few remnants of obsolete code...)
Removed a few obsolete uses of "jtag_speed":
- The Calao stuff hasn't worked since July 2008. (Those Atmel
targets need to work with a 32KHz core clock after reset until
board-specific init-reset code sets up the PLL and enables a
faster JTAg clock.)
- Parport speed controls don't actually work (tops out at about
1 MHz on typical HW).
- In general, speed controls need to live in board.cfg files (or
sometimes target.cfg files), not interface.cfg ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The semantics of "-work-area-virt 0" (or phys) changed with
the patch to require specifying physical or virtrual work
area addresses. Specifying zero was previously a NOP. Now
it means that address zero is valid.
This patch addresses three related issues:
- MMU-less processors should never specify work-area-virt;
remove those specifications. Such processors include
ARM7TDMI, Cortex-M3, and ARM966.
- MMU-equipped processors *can* specify work-area-virt...
but zero won't be appropriate, except in mischievous
contexts (which hide null pointer exceptions).
Remove those specs from those processors too. If any of
those mappings is valid, someone will need to submit a
patch adding it ... along with a comment saying what OS
provides the mapping, and in which context. Example,
say "works with Linux 2.6.30+, in kernel mode". (Note
that ARM Linux doesn't map kernel memory to zero ...)
- Clarify docs on that "-virt" and other work area stuff.
Seems to me work-area-virt is quite problematic; not every
operating system provides such static mappings; if they do,
they're not in every MMU context...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Config for Intel's "Lubbock" PXA255 development board. Even more
so than the PXA255 itself, this is obsolete. AFAIK this was the
first generally available development platform for PXA255. Intel
stopped providing these after other devel boards became available.
One interesting thing about this board from the OpenOCD perspective
is probably its flash configuration. Each bank is 32 bits wide,
built from two 16-bit StrataFlash chips wired in parallel. This
doubles throughput ... it reads/writes 32 bits in the time a single
chip takes to write just 16 bits.
This conf mostly works, given XScale bugfixes, but has some issues
(notably: no access to the on-board SDRAM) flagged by FIXMEs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Gets rid of the runtime warning "stm32.bs: nonstandard IR mask"
[dbrownell@users.sourceforge.net: line lengths, note issue, section ref]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This gets rid of runtime warnings from the use of numbers.
STM32 and LPC2103 were tested. Other LPC updates are the
same, and so are safe. The CFI updates match other tested
changes now in the tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add interface configs for two new high speed JTAG
adapters from Olimex. They need some other speed
related tweaks to work well at high speed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch includes partial support for these new JTAG adapters.
More complete support will require updates to the libftdi code,
for EEPROM access.
[dbrownell@users.sourceforge.net: fix whitespace, linelen, etc ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Now I can issue "reset halt" and have everything act smoothly;
the vector_catch hardware is obviously not kicking in, but the
rest of the reset sequence acts sanely.
- TAP "setup" event enables the DAP, not omap3_dbginit
(resolving a chicken/egg bug I noted a while back)
- Remove stuff from omap3_dbginit which should never be
used in event handlers
- Cope better with slow clocking during reset
Also, stop hard-wiring the target name: use the input params in
the standard way, and set up $_TARGETNAME as an output param.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is the very basic board config for the balloon3 board cpu JTAG
channel.
The rest of the config comprises another 14 .cfg files which I suspect
openocd doesn't really want all of. I'm still not sure how to deal
with this. I'll post another mail/patch to discuss.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Ofrwarded from Ron, who's not subscribed.
----- Forwarded message from Ron <ron@debian.org> -----
From: Ron <ron@debian.org>
Date: Wed, 14 Oct 2009 04:50:17 +1030
To: wookey@debian.org
Subject: [PATCH] OpenRD board configuration
X-Spam-Status: No, score=-3.6 required=4.5 tests=BAYES_00,RCVD_IN_DNSWL_LOW
autolearn=ham version=3.2.5
This piggybacks on the 'sheevaplug' layout which uses the same Kirkwood SoC.
Signed-off-by: Ron Lee <ron@debian.org>
Startup now mostly works, except that the initial target state
is "unknown" ... previously, it refused to even start.
Getting that far required fixing the ircapture value (which
can never have been correct!) and the default JTAG clock rate,
then providing custom reset script.
The "reset" command is still iffy. DCSR updates, and loading
the debug handler, report numerous DR/IR capture failures.
But once that's done, "poll" reports that the CPU is halted
(which it shouldn't be, this was "reset run"!), due to the
rather curious reason "target-not-halted".
Summary: you still can't debug these parts, but it's closer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is clearly noted in the hardware spec (section 5.2.3); it
works around a chip erratum: "If the MPU_RESET signal is used,
it may cause the EMIFS bus to lock."
I seem to have a board with such an initial build. The chip
is labeled XOMAP. Presumably, parts without that "X" prefix
(eXperimental) resolve this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Without some extra delay after releasing SRST, we seemed to
be trying to talk to the TAP before it was ready to respond.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The model is that this fires after scanchain verification, when it's
safe to call "jtag tapenable $TAPNAME". So it will fire as part of
non-error paths of "init" and "reset" command processing. However it
will *NOT* trigger during "jtag_reset" processing, which skips all
scan chain verification, or after verification errors.
ALSO:
- switch DaVinci chips to use this new mechanism
- log TAP activation/deactivation, since their IDCODEs aren't verified
- unify "enum jtag_event" scripted event notifications
- remove duplicative JTAG_TAP_EVENT_POST_RESET
git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
David Brownell
Thomas Kindler
Øyvind Harboe
Krzysztof Kajstura
Freddie Chopin
Dimitar Dimitrov
Oleg Seiljus
Spencer Oliver
Wookey
Dean Glazeski
Rabeeh Khoury
John Rigby
oharboe
dbrownell
mlu