Currently the board/redbee-*.cfg files incorrectly include the
interface definition. Move the interfaces to interface/,
and create a single board/redbee.cfg that is common to both boards.
Intended usage is now:
openocd -f interface/redbee-econotag.cfg -f board/redbee.cfg
Posted by telekatz@gmx.de in the bettyhacks forum for openocd
0.4.0 and integrated into 0.5.0 by Gunnar Henne.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
buspirate has never supported building on native windows (mingw).
configure will now check this is not the case.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
AC_CHECK_FILE will die when cross-compiling. So don't use it to test the existence of guess-rev.sh.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Due to build warnings introduced in newer versions of ftd2xx we
use strings to report errors rather than result codes. This also
gives us the same behaviour as libftdi.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Scripts sourced via 'script' should evaluate in the global
scope to make it easy to set and reference global variables.
Signed-off-by: Steve Bennett <steveb@workware.net.au>
i had started my code from dsp5683xx, i renamed a bunch of stuff to names i consider to be better.
i believe no one is using this code, so nobody should be affected. (it's not too late to do this change)
After correcting the reply size counter, it should be safe to rely on it
for the number of bytes expected in the USB read, instead of reading the
endpoint maximum. This doesn't make things go any faster but it's nicer and
removes the local buffer.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add a helper function for running the queue if it would overflow otherwise.
Use it to simplify the queue fill level checks and optimize in a few cases
that would previously run the queue prematurely.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
After the reply_index handling is fixed, there's no need to special case
the out scan.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
dtc_queue.reply_index was wrongly being increased during out scans, causing
the queue to be sent before the out buffer was full. This patch increases
raw upload speed by 50% or so.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Indentation was inconsistent and some lines not indented at all. Quickfix
using Eclipse's auto-indentation.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
Pprogram that loads another program into memory is actually writing the
D- side cache.
The instructions it has loaded can't be executed until they reach the
I-cache.
After the instructions have been written, the loader should arrange to
write back any containing D-cache line and invalidate any locations
already in the I-cache.
For the MIPS Architecture Release2 cores, we can use synci command
that does this job.
For Release1 we must use "cache" instruction.
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
For all architectures we use distinct common magic number,
and this should be a uint32_t type.
Otherwise, comparison with macros will yield compilation
warning.
if tap enable/disable failed then a warning was written to the log, but JIM_OK was returned. if using openocd via a TCP interface to the TCL port, there is no way to catch that the command failed (it didn't enable the tap, so it failed)
now it return an error if it fails.
There are some older atmel nor chips which have negated logic for
TopBottom detection. This patch adds a special handling for the old
chips. This is the same mechanism as implemented in linux kernel.
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
before doing anything with the flash module (FM) the clock divider must be set.
if erase_check was the first thing done with the FM after reset then an error would be generated because the clk divider was not set.
now erase_check sets the clk divider.
reorganized code to get rid of compiler warnings
the warning were related to allignment, i do not get these warning on my build system (i've tried setting the compiler flag but it doesn't work, still working on why) so i cannot detect them (yet.)
Evan Hunter
Jonathan Dumaresq
Jie Zhang
Evan
Jim Paris
Andreas Bießmann
olivier Schonken
Gunnar Henne
Spencer Oliver
SimonQian
Øyvind Harboe
Stefan Mahr
Steve Bennett
Rodrigo L. Rosa
Andreas Fritiofson
Drasko DRASKOVIC
Jean-Christophe PLAGNIOL-VILLARD