riscv-openocd/tcl/target/stm32f0x.cfg

# script for stm32f0x family

#
# stm32 devices support SWD transports only.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]

if { [info exists CHIPNAME] } {
   set _CHIPNAME $CHIPNAME
} else {
   set _CHIPNAME stm32f0x
}

set _ENDIAN little

# Work-area is a space in RAM used for flash programming
# By default use 4kB
if { [info exists WORKAREASIZE] } {
   set _WORKAREASIZE $WORKAREASIZE
} else {
   set _WORKAREASIZE 0x1000
}

# Allow overriding the Flash bank size
if { [info exists FLASH_SIZE] } {
	set _FLASH_SIZE $FLASH_SIZE
} else {
	# autodetect size
	set _FLASH_SIZE 0
}

#jtag scan chain
if { [info exists CPUTAPID] } {
   set _CPUTAPID $CPUTAPID
} else {
  # See STM Document RM0091
  # Section 29.5.3
   set _CPUTAPID 0x0bb11477
}

swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap

$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0

# flash size will be probed
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME stm32f1x 0x08000000 $_FLASH_SIZE 0 0 $_TARGETNAME

# adapter speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
adapter speed 1000

adapter srst delay 100

reset_config srst_nogate

if {![using_hla]} {
   # if srst is not fitted use SYSRESETREQ to
   # perform a soft reset
   cortex_m reset_config sysresetreq
}

proc stm32f0x_default_reset_start {} {
	# Reset clock is HSI (8 MHz)
	adapter speed 1000
}

proc stm32f0x_default_examine_end {} {
	# Enable debug during low power modes (uses more power)
	mmw 0x40015804 0x00000006 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP

	# Stop watchdog counters during halt
	mmw 0x40015808 0x00001800 0 ;# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
}

proc stm32f0x_default_reset_init {} {
	# Configure PLL to boost clock to HSI x 6 (48 MHz)
	mww 0x40021004 0x00100000   ;# RCC_CFGR = PLLMUL[2]
	mmw 0x40021000 0x01000000 0 ;# RCC_CR[31:16] |= PLLON
	mww 0x40022000 0x00000011   ;# FLASH_ACR = PRFTBE | LATENCY[0]
	sleep 10                    ;# Wait for PLL to lock
	mmw 0x40021004 0x00000002 0 ;# RCC_CFGR |= SW[1]

	# Boost JTAG frequency
	adapter speed 8000
}

# Default hooks
$_TARGETNAME configure -event examine-end { stm32f0x_default_examine_end }
$_TARGETNAME configure -event reset-start { stm32f0x_default_reset_start }
$_TARGETNAME configure -event reset-init { stm32f0x_default_reset_init }