mirror of https://github.com/YosysHQ/yosys.git
111 lines
2.0 KiB
Verilog
111 lines
2.0 KiB
Verilog
`timescale 1ns/1ps
|
|
|
|
/*
|
|
This file contains analog / mixed signal cells, or other things that are not possible to fully model
|
|
in behavioral Verilog.
|
|
|
|
It also contains some stuff like oscillators that use non-synthesizeable constructs such as delays.
|
|
TODO: do we want a third file for those cells?
|
|
*/
|
|
|
|
module GP_ABUF(input wire IN, output wire OUT);
|
|
|
|
assign OUT = IN;
|
|
|
|
//must be 1, 5, 20, 50
|
|
//values >1 only available with Vdd > 2.7V
|
|
parameter BANDWIDTH_KHZ = 1;
|
|
|
|
endmodule
|
|
|
|
module GP_ACMP(input wire PWREN, input wire VIN, input wire VREF, output reg OUT);
|
|
|
|
parameter BANDWIDTH = "HIGH";
|
|
parameter VIN_ATTEN = 1;
|
|
parameter VIN_ISRC_EN = 0;
|
|
parameter HYSTERESIS = 0;
|
|
|
|
initial OUT = 0;
|
|
|
|
endmodule
|
|
|
|
module GP_BANDGAP(output reg OK);
|
|
parameter AUTO_PWRDN = 1;
|
|
parameter CHOPPER_EN = 1;
|
|
parameter OUT_DELAY = 100;
|
|
|
|
endmodule
|
|
|
|
module GP_DAC(input[7:0] DIN, input wire VREF, output reg VOUT);
|
|
|
|
initial VOUT = 0;
|
|
|
|
//analog hard IP is not supported for simulation
|
|
|
|
endmodule
|
|
|
|
module GP_LFOSC(input PWRDN, output reg CLKOUT);
|
|
|
|
parameter PWRDN_EN = 0;
|
|
parameter AUTO_PWRDN = 0;
|
|
parameter OUT_DIV = 1;
|
|
|
|
initial CLKOUT = 0;
|
|
|
|
//auto powerdown not implemented for simulation
|
|
//output dividers not implemented for simulation
|
|
|
|
always begin
|
|
if(PWRDN)
|
|
CLKOUT = 0;
|
|
else begin
|
|
//half period of 1730 Hz
|
|
#289017;
|
|
CLKOUT = ~CLKOUT;
|
|
end
|
|
end
|
|
|
|
endmodule
|
|
|
|
module GP_PGA(input wire VIN_P, input wire VIN_N, input wire VIN_SEL, output reg VOUT);
|
|
|
|
parameter GAIN = 1;
|
|
parameter INPUT_MODE = "SINGLE";
|
|
|
|
initial VOUT = 0;
|
|
|
|
//cannot simulate mixed signal IP
|
|
|
|
endmodule
|
|
|
|
module GP_PWRDET(output reg VDD_LOW);
|
|
initial VDD_LOW = 0;
|
|
endmodule
|
|
|
|
module GP_VREF(input VIN, output reg VOUT);
|
|
parameter VIN_DIV = 1;
|
|
parameter VREF = 0;
|
|
//cannot simulate mixed signal IP
|
|
endmodule
|
|
|
|
module GP_POR(output reg RST_DONE);
|
|
parameter POR_TIME = 500;
|
|
|
|
initial begin
|
|
RST_DONE = 0;
|
|
|
|
if(POR_TIME == 4)
|
|
#4000;
|
|
else if(POR_TIME == 500)
|
|
#500000;
|
|
else begin
|
|
$display("ERROR: bad POR_TIME for GP_POR cell");
|
|
$finish;
|
|
end
|
|
|
|
RST_DONE = 1;
|
|
|
|
end
|
|
|
|
endmodule
|