mirror of https://github.com/YosysHQ/yosys.git
1021 lines
41 KiB
ReStructuredText
1021 lines
41 KiB
ReStructuredText
.. role:: verilog(code)
|
||
:language: Verilog
|
||
|
||
.. _chapter:celllib:
|
||
|
||
Internal cell library
|
||
=====================
|
||
|
||
Most of the passes in Yosys operate on netlists, i.e. they only care about the
|
||
RTLIL::Wire and RTLIL::Cell objects in an RTLIL::Module. This chapter discusses
|
||
the cell types used by Yosys to represent a behavioural design internally.
|
||
|
||
This chapter is split in two parts. In the first part the internal RTL cells are
|
||
covered. These cells are used to represent the design on a coarse grain level.
|
||
Like in the original HDL code on this level the cells operate on vectors of
|
||
signals and complex cells like adders exist. In the second part the internal
|
||
gate cells are covered. These cells are used to represent the design on a
|
||
fine-grain gate-level. All cells from this category operate on single bit
|
||
signals.
|
||
|
||
RTL cells
|
||
---------
|
||
|
||
Most of the RTL cells closely resemble the operators available in HDLs such as
|
||
Verilog or VHDL. Therefore Verilog operators are used in the following sections
|
||
to define the behaviour of the RTL cells.
|
||
|
||
Note that all RTL cells have parameters indicating the size of inputs and
|
||
outputs. When passes modify RTL cells they must always keep the values of these
|
||
parameters in sync with the size of the signals connected to the inputs and
|
||
outputs.
|
||
|
||
Simulation models for the RTL cells can be found in the file
|
||
``techlibs/common/simlib.v`` in the Yosys source tree.
|
||
|
||
Unary operators
|
||
~~~~~~~~~~~~~~~
|
||
|
||
All unary RTL cells have one input port ``\A`` and one output port ``\Y``. They
|
||
also have the following parameters:
|
||
|
||
``\A_SIGNED``
|
||
Set to a non-zero value if the input ``\A`` is signed and therefore
|
||
should be sign-extended when needed.
|
||
|
||
``\A_WIDTH``
|
||
The width of the input port ``\A``.
|
||
|
||
``\Y_WIDTH``
|
||
The width of the output port ``\Y``.
|
||
|
||
:numref:`tab:CellLib_unary` lists all cells for unary RTL operators.
|
||
|
||
.. table:: Cell types for unary operators with their corresponding Verilog expressions.
|
||
:name: tab:CellLib_unary
|
||
|
||
================== ============
|
||
Verilog Cell Type
|
||
================== ============
|
||
:verilog:`Y = ~A` $not
|
||
:verilog:`Y = +A` $pos
|
||
:verilog:`Y = -A` $neg
|
||
:verilog:`Y = &A` $reduce_and
|
||
:verilog:`Y = |A` $reduce_or
|
||
:verilog:`Y = ^A` $reduce_xor
|
||
:verilog:`Y = ~^A` $reduce_xnor
|
||
:verilog:`Y = |A` $reduce_bool
|
||
:verilog:`Y = !A` $logic_not
|
||
================== ============
|
||
|
||
For the unary cells that output a logical value (``$reduce_and``,
|
||
``$reduce_or``, ``$reduce_xor``, ``$reduce_xnor``, ``$reduce_bool``,
|
||
``$logic_not``), when the ``\Y_WIDTH`` parameter is greater than 1, the output
|
||
is zero-extended, and only the least significant bit varies.
|
||
|
||
Note that ``$reduce_or`` and ``$reduce_bool`` actually represent the same logic
|
||
function. But the HDL frontends generate them in different situations. A
|
||
``$reduce_or`` cell is generated when the prefix ``|`` operator is being used. A
|
||
``$reduce_bool`` cell is generated when a bit vector is used as a condition in
|
||
an ``if``-statement or ``?:``-expression.
|
||
|
||
Binary operators
|
||
~~~~~~~~~~~~~~~~
|
||
|
||
All binary RTL cells have two input ports ``\A`` and ``\B`` and one output port
|
||
``\Y``. They also have the following parameters:
|
||
|
||
``\A_SIGNED``
|
||
Set to a non-zero value if the input ``\A`` is signed and therefore
|
||
should be sign-extended when needed.
|
||
|
||
``\A_WIDTH``
|
||
The width of the input port ``\A``.
|
||
|
||
``\B_SIGNED``
|
||
Set to a non-zero value if the input ``\B`` is signed and therefore
|
||
should be sign-extended when needed.
|
||
|
||
``\B_WIDTH``
|
||
The width of the input port ``\B``.
|
||
|
||
``\Y_WIDTH``
|
||
The width of the output port ``\Y``.
|
||
|
||
:numref:`tab:CellLib_binary` lists all cells for binary RTL operators.
|
||
|
||
.. table:: Cell types for binary operators with their corresponding Verilog expressions.
|
||
:name: tab:CellLib_binary
|
||
|
||
======================= ============= ======================= =========
|
||
Verilog Cell Type Verilog Cell Type
|
||
======================= ============= ======================= =========
|
||
:verilog:`Y = A & B` $and :verilog:`Y = A < B` $lt
|
||
:verilog:`Y = A | B` $or :verilog:`Y = A <= B` $le
|
||
:verilog:`Y = A ^ B` $xor :verilog:`Y = A == B` $eq
|
||
:verilog:`Y = A ~^ B` $xnor :verilog:`Y = A != B` $ne
|
||
:verilog:`Y = A << B` $shl :verilog:`Y = A >= B` $ge
|
||
:verilog:`Y = A >> B` $shr :verilog:`Y = A > B` $gt
|
||
:verilog:`Y = A <<< B` $sshl :verilog:`Y = A + B` $add
|
||
:verilog:`Y = A >>> B` $sshr :verilog:`Y = A - B` $sub
|
||
:verilog:`Y = A && B` $logic_and :verilog:`Y = A * B` $mul
|
||
:verilog:`Y = A || B` $logic_or :verilog:`Y = A / B` $div
|
||
:verilog:`Y = A === B` $eqx :verilog:`Y = A % B` $mod
|
||
:verilog:`Y = A !== B` $nex ``N/A`` $divfloor
|
||
:verilog:`Y = A ** B` $pow ``N/A`` $modfoor
|
||
======================= ============= ======================= =========
|
||
|
||
The ``$shl`` and ``$shr`` cells implement logical shifts, whereas the ``$sshl``
|
||
and ``$sshr`` cells implement arithmetic shifts. The ``$shl`` and ``$sshl``
|
||
cells implement the same operation. All four of these cells interpret the second
|
||
operand as unsigned, and require ``\B_SIGNED`` to be zero.
|
||
|
||
Two additional shift operator cells are available that do not directly
|
||
correspond to any operator in Verilog, ``$shift`` and ``$shiftx``. The
|
||
``$shift`` cell performs a right logical shift if the second operand is positive
|
||
(or unsigned), and a left logical shift if it is negative. The ``$shiftx`` cell
|
||
performs the same operation as the ``$shift`` cell, but the vacated bit
|
||
positions are filled with undef (x) bits, and corresponds to the Verilog indexed
|
||
part-select expression.
|
||
|
||
For the binary cells that output a logical value (``$logic_and``, ``$logic_or``,
|
||
``$eqx``, ``$nex``, ``$lt``, ``$le``, ``$eq``, ``$ne``, ``$ge``, ``$gt)``, when
|
||
the ``\Y_WIDTH`` parameter is greater than 1, the output is zero-extended, and
|
||
only the least significant bit varies.
|
||
|
||
Division and modulo cells are available in two rounding modes. The original
|
||
``$div`` and ``$mod`` cells are based on truncating division, and correspond to
|
||
the semantics of the verilog ``/`` and ``%`` operators. The ``$divfloor`` and
|
||
``$modfloor`` cells represent flooring division and flooring modulo, the latter
|
||
of which is also known as "remainder" in several languages. See
|
||
:numref:`tab:CellLib_divmod` for a side-by-side comparison between the different
|
||
semantics.
|
||
|
||
.. table:: Comparison between different rounding modes for division and modulo cells.
|
||
:name: tab:CellLib_divmod
|
||
|
||
+-----------+--------+-----------+-----------+-----------+-----------+
|
||
| Division | Result | Truncating | Flooring |
|
||
+-----------+--------+-----------+-----------+-----------+-----------+
|
||
| | | $div | $mod | $divfloor | $modfloor |
|
||
+===========+========+===========+===========+===========+===========+
|
||
| -10 / 3 | -3.3 | -3 | -1 | -4 | 2 |
|
||
+-----------+--------+-----------+-----------+-----------+-----------+
|
||
| 10 / -3 | -3.3 | -3 | 1 | -4 | -2 |
|
||
+-----------+--------+-----------+-----------+-----------+-----------+
|
||
| -10 / -3 | 3.3 | 3 | -1 | 3 | -1 |
|
||
+-----------+--------+-----------+-----------+-----------+-----------+
|
||
| 10 / 3 | 3.3 | 3 | 1 | 3 | 1 |
|
||
+-----------+--------+-----------+-----------+-----------+-----------+
|
||
|
||
Multiplexers
|
||
~~~~~~~~~~~~
|
||
|
||
Multiplexers are generated by the Verilog HDL frontend for ``?:``-expressions.
|
||
Multiplexers are also generated by the proc pass to map the decision trees from
|
||
RTLIL::Process objects to logic.
|
||
|
||
The simplest multiplexer cell type is ``$mux``. Cells of this type have a
|
||
``\WITDH`` parameter and data inputs ``\A`` and ``\B`` and a data output ``\Y``,
|
||
all of the specified width. This cell also has a single bit control input
|
||
``\S``. If ``\S`` is 0 the value from the input ``\A`` is sent to the output, if
|
||
it is 1 the value from the ``\B`` input is sent to the output. So the ``$mux``
|
||
cell implements the function :verilog:`Y = S ? B : A`.
|
||
|
||
The ``$pmux`` cell is used to multiplex between many inputs using a one-hot
|
||
select signal. Cells of this type have a ``\WIDTH`` and a ``\S_WIDTH`` parameter
|
||
and inputs ``\A``, ``\B``, and ``\S`` and an output ``\Y``. The ``\S`` input is
|
||
``\S_WIDTH`` bits wide. The ``\A`` input and the output are both ``\WIDTH`` bits
|
||
wide and the ``\B`` input is ``\WIDTH*\S_WIDTH`` bits wide. When all bits of
|
||
``\S`` are zero, the value from ``\A`` input is sent to the output. If the
|
||
:math:`n`\ 'th bit from ``\S`` is set, the value :math:`n`\ 'th ``\WIDTH`` bits
|
||
wide slice of the ``\B`` input is sent to the output. When more than one bit
|
||
from ``\S`` is set the output is undefined. Cells of this type are used to model
|
||
"parallel cases" (defined by using the ``parallel_case`` attribute or detected
|
||
by an optimization).
|
||
|
||
The ``$tribuf`` cell is used to implement tristate logic. Cells of this type
|
||
have a ``\B`` parameter and inputs ``\A`` and ``\EN`` and an output ``\Y``. The
|
||
``\A`` input and ``\Y`` output are ``\WIDTH`` bits wide, and the ``\EN`` input
|
||
is one bit wide. When ``\EN`` is 0, the output is not driven. When ``\EN`` is 1,
|
||
the value from ``\A`` input is sent to the ``\Y`` output. Therefore, the
|
||
``$tribuf`` cell implements the function :verilog:`Y = EN ? A : 'bz`.
|
||
|
||
Behavioural code with cascaded if-then-else- and case-statements usually results
|
||
in trees of multiplexer cells. Many passes (from various optimizations to FSM
|
||
extraction) heavily depend on these multiplexer trees to understand dependencies
|
||
between signals. Therefore optimizations should not break these multiplexer
|
||
trees (e.g. by replacing a multiplexer between a calculated signal and a
|
||
constant zero with an ``$and`` gate).
|
||
|
||
Registers
|
||
~~~~~~~~~
|
||
|
||
SR-type latches are represented by ``$sr`` cells. These cells have input ports
|
||
``\SET`` and ``\CLR`` and an output port ``\Q``. They have the following
|
||
parameters:
|
||
|
||
``\WIDTH``
|
||
The width of inputs ``\SET`` and ``\CLR`` and output ``\Q``.
|
||
|
||
``\SET_POLARITY``
|
||
The set input bits are active-high if this parameter has the value
|
||
``1'b1`` and active-low if this parameter is ``1'b0``.
|
||
|
||
``\CLR_POLARITY``
|
||
The reset input bits are active-high if this parameter has the value
|
||
``1'b1`` and active-low if this parameter is ``1'b0``.
|
||
|
||
Both set and reset inputs have separate bits for every output bit. When both the
|
||
set and reset inputs of an ``$sr`` cell are active for a given bit index, the
|
||
reset input takes precedence.
|
||
|
||
D-type flip-flops are represented by ``$dff`` cells. These cells have a clock
|
||
port ``\CLK``, an input port ``\D`` and an output port ``\Q``. The following
|
||
parameters are available for ``$dff`` cells:
|
||
|
||
``\WIDTH``
|
||
The width of input ``\D`` and output ``\Q``.
|
||
|
||
``\CLK_POLARITY``
|
||
Clock is active on the positive edge if this parameter has the value
|
||
``1'b1`` and on the negative edge if this parameter is ``1'b0``.
|
||
|
||
D-type flip-flops with asynchronous reset are represented by ``$adff`` cells. As
|
||
the ``$dff`` cells they have ``\CLK``, ``\D`` and ``\Q`` ports. In addition they
|
||
also have a single-bit ``\ARST`` input port for the reset pin and the following
|
||
additional two parameters:
|
||
|
||
``\ARST_POLARITY``
|
||
The asynchronous reset is active-high if this parameter has the value
|
||
``1'b1`` and active-low if this parameter is ``1'b0``.
|
||
|
||
``\ARST_VALUE``
|
||
The state of ``\Q`` will be set to this value when the reset is active.
|
||
|
||
Usually these cells are generated by the ``proc`` pass using the information in
|
||
the designs RTLIL::Process objects.
|
||
|
||
D-type flip-flops with synchronous reset are represented by ``$sdff`` cells. As
|
||
the ``$dff`` cells they have ``\CLK``, ``\D`` and ``\Q`` ports. In addition they
|
||
also have a single-bit ``\SRST`` input port for the reset pin and the following
|
||
additional two parameters:
|
||
|
||
``\SRST_POLARITY``
|
||
The synchronous reset is active-high if this parameter has the value
|
||
``1'b1`` and active-low if this parameter is ``1'b0``.
|
||
|
||
``\SRST_VALUE``
|
||
The state of ``\Q`` will be set to this value when the reset is active.
|
||
|
||
Note that the ``$adff`` and ``$sdff`` cells can only be used when the reset value is
|
||
constant.
|
||
|
||
D-type flip-flops with asynchronous load are represented by ``$aldff`` cells. As
|
||
the ``$dff`` cells they have ``\CLK``, ``\D`` and ``\Q`` ports. In addition they
|
||
also have a single-bit ``\ALOAD`` input port for the async load enable pin, a
|
||
``\AD`` input port with the same width as data for the async load data, and the
|
||
following additional parameter:
|
||
|
||
``\ALOAD_POLARITY``
|
||
The asynchronous load is active-high if this parameter has the value
|
||
``1'b1`` and active-low if this parameter is ``1'b0``.
|
||
|
||
D-type flip-flops with asynchronous set and reset are represented by ``$dffsr``
|
||
cells. As the ``$dff`` cells they have ``\CLK``, ``\D`` and ``\Q`` ports. In
|
||
addition they also have multi-bit ``\SET`` and ``\CLR`` input ports and the
|
||
corresponding polarity parameters, like ``$sr`` cells.
|
||
|
||
D-type flip-flops with enable are represented by ``$dffe``, ``$adffe``,
|
||
``$aldffe``, ``$dffsre``, ``$sdffe``, and ``$sdffce`` cells, which are enhanced
|
||
variants of ``$dff``, ``$adff``, ``$aldff``, ``$dffsr``, ``$sdff`` (with reset
|
||
over enable) and ``$sdff`` (with enable over reset) cells, respectively. They
|
||
have the same ports and parameters as their base cell. In addition they also
|
||
have a single-bit ``\EN`` input port for the enable pin and the following
|
||
parameter:
|
||
|
||
``\EN_POLARITY``
|
||
The enable input is active-high if this parameter has the value ``1'b1``
|
||
and active-low if this parameter is ``1'b0``.
|
||
|
||
D-type latches are represented by ``$dlatch`` cells. These cells have an enable
|
||
port ``\EN``, an input port ``\D``, and an output port ``\Q``. The following
|
||
parameters are available for ``$dlatch`` cells:
|
||
|
||
``\WIDTH``
|
||
The width of input ``\D`` and output ``\Q``.
|
||
|
||
``\EN_POLARITY``
|
||
The enable input is active-high if this parameter has the value ``1'b1``
|
||
and active-low if this parameter is ``1'b0``.
|
||
|
||
The latch is transparent when the ``\EN`` input is active.
|
||
|
||
D-type latches with reset are represented by ``$adlatch`` cells. In addition to
|
||
``$dlatch`` ports and parameters, they also have a single-bit ``\ARST`` input
|
||
port for the reset pin and the following additional parameters:
|
||
|
||
``\ARST_POLARITY``
|
||
The asynchronous reset is active-high if this parameter has the value
|
||
``1'b1`` and active-low if this parameter is ``1'b0``.
|
||
|
||
``\ARST_VALUE``
|
||
The state of ``\Q`` will be set to this value when the reset is active.
|
||
|
||
D-type latches with set and reset are represented by ``$dlatchsr`` cells. In
|
||
addition to ``$dlatch`` ports and parameters, they also have multi-bit ``\SET``
|
||
and ``\CLR`` input ports and the corresponding polarity parameters, like ``$sr``
|
||
cells.
|
||
|
||
.. _sec:memcells:
|
||
|
||
Memories
|
||
~~~~~~~~
|
||
|
||
Memories are either represented using RTLIL::Memory objects, ``$memrd_v2``,
|
||
``$memwr_v2``, and ``$meminit_v2`` cells, or by ``$mem_v2`` cells alone.
|
||
|
||
In the first alternative the RTLIL::Memory objects hold the general metadata for
|
||
the memory (bit width, size in number of words, etc.) and for each port a
|
||
``$memrd_v2`` (read port) or ``$memwr_v2`` (write port) cell is created. Having
|
||
individual cells for read and write ports has the advantage that they can be
|
||
consolidated using resource sharing passes. In some cases this drastically
|
||
reduces the number of required ports on the memory cell. In this alternative,
|
||
memory initialization data is represented by ``$meminit_v2`` cells, which allow
|
||
delaying constant folding for initialization addresses and data until after the
|
||
frontend finishes.
|
||
|
||
The ``$memrd_v2`` cells have a clock input ``\CLK``, an enable input ``\EN``, an
|
||
address input ``\ADDR``, a data output ``\DATA``, an asynchronous reset input
|
||
``\ARST``, and a synchronous reset input ``\SRST``. They also have the following
|
||
parameters:
|
||
|
||
``\MEMID``
|
||
The name of the RTLIL::Memory object that is associated with this read
|
||
port.
|
||
|
||
``\ABITS``
|
||
The number of address bits (width of the ``\ADDR`` input port).
|
||
|
||
``\WIDTH``
|
||
The number of data bits (width of the ``\DATA`` output port). Note that
|
||
this may be a power-of-two multiple of the underlying memory's width --
|
||
such ports are called wide ports and access an aligned group of cells at
|
||
once. In this case, the corresponding low bits of ``\ADDR`` must be
|
||
tied to 0.
|
||
|
||
``\CLK_ENABLE``
|
||
When this parameter is non-zero, the clock is used. Otherwise this read
|
||
port is asynchronous and the ``\CLK`` input is not used.
|
||
|
||
``\CLK_POLARITY``
|
||
Clock is active on the positive edge if this parameter has the value
|
||
``1'b1`` and on the negative edge if this parameter is ``1'b0``.
|
||
|
||
``\TRANSPARENCY_MASK``
|
||
This parameter is a bitmask of write ports that this read port is
|
||
transparent with. The bits of this parameter are indexed by the write
|
||
port's ``\PORTID`` parameter. Transparency can only be enabled between
|
||
synchronous ports sharing a clock domain. When transparency is enabled
|
||
for a given port pair, a read and write to the same address in the same
|
||
cycle will return the new value. Otherwise the old value is returned.
|
||
|
||
``\COLLISION_X_MASK``
|
||
This parameter is a bitmask of write ports that have undefined collision
|
||
behavior with this port. The bits of this parameter are indexed by the
|
||
write port's ``\PORTID`` parameter. This behavior can only be enabled
|
||
between synchronous ports sharing a clock domain. When undefined
|
||
collision is enabled for a given port pair, a read and write to the same
|
||
address in the same cycle will return the undefined (all-X) value.This
|
||
option is exclusive (for a given port pair) with the transparency
|
||
option.
|
||
|
||
``\ARST_VALUE``
|
||
Whenever the ``\ARST`` input is asserted, the data output will be reset
|
||
to this value. Only used for synchronous ports.
|
||
|
||
``\SRST_VALUE``
|
||
Whenever the ``\SRST`` input is synchronously asserted, the data output
|
||
will be reset to this value. Only used for synchronous ports.
|
||
|
||
``\INIT_VALUE``
|
||
The initial value of the data output, for synchronous ports.
|
||
|
||
``\CE_OVER_SRST``
|
||
If this parameter is non-zero, the ``\SRST`` input is only recognized
|
||
when ``\EN`` is true. Otherwise, ``\SRST`` is recognized regardless of
|
||
``\EN``.
|
||
|
||
The ``$memwr_v2`` cells have a clock input ``\CLK``, an enable input ``\EN``
|
||
(one enable bit for each data bit), an address input ``\ADDR`` and a data input
|
||
``\DATA``. They also have the following parameters:
|
||
|
||
``\MEMID``
|
||
The name of the RTLIL::Memory object that is associated with this write
|
||
port.
|
||
|
||
``\ABITS``
|
||
The number of address bits (width of the ``\ADDR`` input port).
|
||
|
||
``\WIDTH``
|
||
The number of data bits (width of the ``\DATA`` output port). Like with
|
||
``$memrd_v2`` cells, the width is allowed to be any power-of-two
|
||
multiple of memory width, with the corresponding restriction on address.
|
||
|
||
``\CLK_ENABLE``
|
||
When this parameter is non-zero, the clock is used. Otherwise this write
|
||
port is asynchronous and the ``\CLK`` input is not used.
|
||
|
||
``\CLK_POLARITY``
|
||
Clock is active on positive edge if this parameter has the value
|
||
``1'b1`` and on the negative edge if this parameter is ``1'b0``.
|
||
|
||
``\PORTID``
|
||
An identifier for this write port, used to index write port bit mask parameters.
|
||
|
||
``\PRIORITY_MASK``
|
||
This parameter is a bitmask of write ports that this write port has
|
||
priority over in case of writing to the same address. The bits of this
|
||
parameter are indexed by the other write port's ``\PORTID`` parameter.
|
||
Write ports can only have priority over write ports with lower port ID.
|
||
When two ports write to the same address and neither has priority over
|
||
the other, the result is undefined. Priority can only be set between
|
||
two synchronous ports sharing the same clock domain.
|
||
|
||
The ``$meminit_v2`` cells have an address input ``\ADDR``, a data input
|
||
``\DATA``, with the width of the ``\DATA`` port equal to ``\WIDTH`` parameter
|
||
times ``\WORDS`` parameter, and a bit enable mask input ``\EN`` with width equal
|
||
to ``\WIDTH`` parameter. All three of the inputs must resolve to a constant for
|
||
synthesis to succeed.
|
||
|
||
``\MEMID``
|
||
The name of the RTLIL::Memory object that is associated with this
|
||
initialization cell.
|
||
|
||
``\ABITS``
|
||
The number of address bits (width of the ``\ADDR`` input port).
|
||
|
||
``\WIDTH``
|
||
The number of data bits per memory location.
|
||
|
||
``\WORDS``
|
||
The number of consecutive memory locations initialized by this cell.
|
||
|
||
``\PRIORITY``
|
||
The cell with the higher integer value in this parameter wins an
|
||
initialization conflict.
|
||
|
||
The HDL frontend models a memory using RTLIL::Memory objects and asynchronous
|
||
``$memrd_v2`` and ``$memwr_v2`` cells. The ``memory`` pass (i.e.~its various
|
||
sub-passes) migrates ``$dff`` cells into the ``$memrd_v2`` and ``$memwr_v2``
|
||
cells making them synchronous, then converts them to a single ``$mem_v2`` cell
|
||
and (optionally) maps this cell type to ``$dff`` cells for the individual words
|
||
and multiplexer-based address decoders for the read and write interfaces. When
|
||
the last step is disabled or not possible, a ``$mem_v2`` cell is left in the
|
||
design.
|
||
|
||
The ``$mem_v2`` cell provides the following parameters:
|
||
|
||
``\MEMID``
|
||
The name of the original RTLIL::Memory object that became this
|
||
``$mem_v2`` cell.
|
||
|
||
``\SIZE``
|
||
The number of words in the memory.
|
||
|
||
``\ABITS``
|
||
The number of address bits.
|
||
|
||
``\WIDTH``
|
||
The number of data bits per word.
|
||
|
||
``\INIT``
|
||
The initial memory contents.
|
||
|
||
``\RD_PORTS``
|
||
The number of read ports on this memory cell.
|
||
|
||
``\RD_WIDE_CONTINUATION``
|
||
This parameter is ``\RD_PORTS`` bits wide, containing a bitmask of
|
||
"wide continuation" read ports. Such ports are used to represent the
|
||
extra data bits of wide ports in the combined cell, and must have all
|
||
control signals identical with the preceding port, except for address,
|
||
which must have the proper sub-cell address encoded in the low bits.
|
||
|
||
``\RD_CLK_ENABLE``
|
||
This parameter is ``\RD_PORTS`` bits wide, containing a clock enable bit
|
||
for each read port.
|
||
|
||
``\RD_CLK_POLARITY``
|
||
This parameter is ``\RD_PORTS`` bits wide, containing a clock polarity
|
||
bit for each read port.
|
||
|
||
``\RD_TRANSPARENCY_MASK``
|
||
This parameter is ``\RD_PORTS*\WR_PORTS`` bits wide, containing a
|
||
concatenation of all ``\TRANSPARENCY_MASK`` values of the original
|
||
``$memrd_v2`` cells.
|
||
|
||
``\RD_COLLISION_X_MASK``
|
||
This parameter is ``\RD_PORTS*\WR_PORTS`` bits wide, containing a
|
||
concatenation of all ``\COLLISION_X_MASK`` values of the original
|
||
``$memrd_v2`` cells.
|
||
|
||
``\RD_CE_OVER_SRST``
|
||
This parameter is ``\RD_PORTS`` bits wide, determining relative
|
||
synchronous reset and enable priority for each read port.
|
||
|
||
``\RD_INIT_VALUE``
|
||
This parameter is ``\RD_PORTS*\WIDTH`` bits wide, containing the initial
|
||
value for each synchronous read port.
|
||
|
||
``\RD_ARST_VALUE``
|
||
This parameter is ``\RD_PORTS*\WIDTH`` bits wide, containing the
|
||
asynchronous reset value for each synchronous read port.
|
||
|
||
``\RD_SRST_VALUE``
|
||
This parameter is ``\RD_PORTS*\WIDTH`` bits wide, containing the
|
||
synchronous reset value for each synchronous read port.
|
||
|
||
``\WR_PORTS``
|
||
The number of write ports on this memory cell.
|
||
|
||
``\WR_WIDE_CONTINUATION``
|
||
This parameter is ``\WR_PORTS`` bits wide, containing a bitmask of
|
||
"wide continuation" write ports.
|
||
|
||
``\WR_CLK_ENABLE``
|
||
This parameter is ``\WR_PORTS`` bits wide, containing a clock enable bit
|
||
for each write port.
|
||
|
||
``\WR_CLK_POLARITY``
|
||
This parameter is ``\WR_PORTS`` bits wide, containing a clock polarity
|
||
bit for each write port.
|
||
|
||
``\WR_PRIORITY_MASK``
|
||
This parameter is ``\WR_PORTS*\WR_PORTS`` bits wide, containing a
|
||
concatenation of all ``\PRIORITY_MASK`` values of the original
|
||
``$memwr_v2`` cells.
|
||
|
||
The ``$mem_v2`` cell has the following ports:
|
||
|
||
``\RD_CLK``
|
||
This input is ``\RD_PORTS`` bits wide, containing all clock signals for
|
||
the read ports.
|
||
|
||
``\RD_EN``
|
||
This input is ``\RD_PORTS`` bits wide, containing all enable signals for
|
||
the read ports.
|
||
|
||
``\RD_ADDR``
|
||
This input is ``\RD_PORTS*\ABITS`` bits wide, containing all address
|
||
signals for the read ports.
|
||
|
||
``\RD_DATA``
|
||
This input is ``\RD_PORTS*\WIDTH`` bits wide, containing all data
|
||
signals for the read ports.
|
||
|
||
``\RD_ARST``
|
||
This input is ``\RD_PORTS`` bits wide, containing all asynchronous reset
|
||
signals for the read ports.
|
||
|
||
``\RD_SRST``
|
||
This input is ``\RD_PORTS`` bits wide, containing all synchronous reset
|
||
signals for the read ports.
|
||
|
||
``\WR_CLK``
|
||
This input is ``\WR_PORTS`` bits wide, containing all clock signals for
|
||
the write ports.
|
||
|
||
``\WR_EN``
|
||
This input is ``\WR_PORTS*\WIDTH`` bits wide, containing all enable
|
||
signals for the write ports.
|
||
|
||
``\WR_ADDR``
|
||
This input is ``\WR_PORTS*\ABITS`` bits wide, containing all address
|
||
signals for the write ports.
|
||
|
||
``\WR_DATA``
|
||
This input is ``\WR_PORTS*\WIDTH`` bits wide, containing all data
|
||
signals for the write ports.
|
||
|
||
The ``memory_collect`` pass can be used to convert discrete ``$memrd_v2``,
|
||
``$memwr_v2``, and ``$meminit_v2`` cells belonging to the same memory to a
|
||
single ``$mem_v2`` cell, whereas the ``memory_unpack`` pass performs the inverse
|
||
operation. The ``memory_dff`` pass can combine asynchronous memory ports that
|
||
are fed by or feeding registers into synchronous memory ports. The
|
||
``memory_bram`` pass can be used to recognize ``$mem_v2`` cells that can be
|
||
implemented with a block RAM resource on an FPGA. The ``memory_map`` pass can be
|
||
used to implement ``$mem_v2`` cells as basic logic: word-wide DFFs and address
|
||
decoders.
|
||
|
||
Finite state machines
|
||
~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
Add a brief description of the ``$fsm`` cell type.
|
||
|
||
Specify rules
|
||
~~~~~~~~~~~~~
|
||
|
||
Add information about ``$specify2``, ``$specify3``, and ``$specrule`` cells.
|
||
|
||
Formal verification cells
|
||
~~~~~~~~~~~~~~~~~~~~~~~~~
|
||
|
||
Add information about ``$assert``, ``$assume``, ``$live``, ``$fair``,
|
||
``$cover``, ``$equiv``, ``$initstate``, ``$anyconst``, ``$anyseq``,
|
||
``$anyinit``, ``$allconst``, ``$allseq`` cells.
|
||
|
||
Add information about ``$ff`` and ``$_FF_`` cells.
|
||
|
||
.. _sec:celllib_gates:
|
||
|
||
Gates
|
||
-----
|
||
|
||
For gate level logic networks, fixed function single bit cells are used that do
|
||
not provide any parameters.
|
||
|
||
Simulation models for these cells can be found in the file
|
||
techlibs/common/simcells.v in the Yosys source tree.
|
||
|
||
.. table:: Cell types for gate level logic networks (main list)
|
||
:name: tab:CellLib_gates
|
||
|
||
======================================= ============
|
||
Verilog Cell Type
|
||
======================================= ============
|
||
:verilog:`Y = A` $_BUF_
|
||
:verilog:`Y = ~A` $_NOT_
|
||
:verilog:`Y = A & B` $_AND_
|
||
:verilog:`Y = ~(A & B)` $_NAND_
|
||
:verilog:`Y = A & ~B` $_ANDNOT_
|
||
:verilog:`Y = A | B` $_OR_
|
||
:verilog:`Y = ~(A | B)` $_NOR_
|
||
:verilog:`Y = A | ~B` $_ORNOT_
|
||
:verilog:`Y = A ^ B` $_XOR_
|
||
:verilog:`Y = ~(A ^ B)` $_XNOR_
|
||
:verilog:`Y = ~((A & B) | C)` $_AOI3_
|
||
:verilog:`Y = ~((A | B) & C)` $_OAI3_
|
||
:verilog:`Y = ~((A & B) | (C & D))` $_AOI4_
|
||
:verilog:`Y = ~((A | B) & (C | D))` $_OAI4_
|
||
:verilog:`Y = S ? B : A` $_MUX_
|
||
:verilog:`Y = ~(S ? B : A)` $_NMUX_
|
||
(see below) $_MUX4_
|
||
(see below) $_MUX8_
|
||
(see below) $_MUX16_
|
||
:verilog:`Y = EN ? A : 1'bz` $_TBUF_
|
||
:verilog:`always @(negedge C) Q <= D` $_DFF_N_
|
||
:verilog:`always @(posedge C) Q <= D` $_DFF_P_
|
||
:verilog:`always @* if (!E) Q <= D` $_DLATCH_N_
|
||
:verilog:`always @* if (E) Q <= D` $_DLATCH_P_
|
||
======================================= ============
|
||
|
||
.. table:: Cell types for gate level logic networks (FFs with reset)
|
||
:name: tab:CellLib_gates_adff
|
||
|
||
================== ============== ============== =======================
|
||
:math:`ClkEdge` :math:`RstLvl` :math:`RstVal` Cell Type
|
||
================== ============== ============== =======================
|
||
:verilog:`negedge` ``0`` ``0`` $_DFF_NN0_, $_SDFF_NN0_
|
||
:verilog:`negedge` ``0`` ``1`` $_DFF_NN1_, $_SDFF_NN1_
|
||
:verilog:`negedge` ``1`` ``0`` $_DFF_NP0_, $_SDFF_NP0_
|
||
:verilog:`negedge` ``1`` ``1`` $_DFF_NP1_, $_SDFF_NP1_
|
||
:verilog:`posedge` ``0`` ``0`` $_DFF_PN0_, $_SDFF_PN0_
|
||
:verilog:`posedge` ``0`` ``1`` $_DFF_PN1_, $_SDFF_PN1_
|
||
:verilog:`posedge` ``1`` ``0`` $_DFF_PP0_, $_SDFF_PP0_
|
||
:verilog:`posedge` ``1`` ``1`` $_DFF_PP1_, $_SDFF_PP1_
|
||
================== ============== ============== =======================
|
||
|
||
|
||
.. table:: Cell types for gate level logic networks (FFs with enable)
|
||
:name: tab:CellLib_gates_dffe
|
||
|
||
================== ============= ===========
|
||
:math:`ClkEdge` :math:`EnLvl` Cell Type
|
||
================== ============= ===========
|
||
:verilog:`negedge` ``0`` $_DFFE_NN_
|
||
:verilog:`negedge` ``1`` $_DFFE_NP_
|
||
:verilog:`posedge` ``0`` $_DFFE_PN_
|
||
:verilog:`posedge` ``1`` $_DFFE_PP_
|
||
================== ============= ===========
|
||
|
||
|
||
.. table:: Cell types for gate level logic networks (FFs with reset and enable)
|
||
:name: tab:CellLib_gates_adffe
|
||
|
||
================== ============== ============== ============= ===========================================
|
||
:math:`ClkEdge` :math:`RstLvl` :math:`RstVal` :math:`EnLvl` Cell Type
|
||
================== ============== ============== ============= ===========================================
|
||
:verilog:`negedge` ``0`` ``0`` ``0`` $_DFFE_NN0N_, $_SDFFE_NN0N_, $_SDFFCE_NN0N_
|
||
:verilog:`negedge` ``0`` ``0`` ``1`` $_DFFE_NN0P_, $_SDFFE_NN0P_, $_SDFFCE_NN0P_
|
||
:verilog:`negedge` ``0`` ``1`` ``0`` $_DFFE_NN1N_, $_SDFFE_NN1N_, $_SDFFCE_NN1N_
|
||
:verilog:`negedge` ``0`` ``1`` ``1`` $_DFFE_NN1P_, $_SDFFE_NN1P_, $_SDFFCE_NN1P_
|
||
:verilog:`negedge` ``1`` ``0`` ``0`` $_DFFE_NP0N_, $_SDFFE_NP0N_, $_SDFFCE_NP0N_
|
||
:verilog:`negedge` ``1`` ``0`` ``1`` $_DFFE_NP0P_, $_SDFFE_NP0P_, $_SDFFCE_NP0P_
|
||
:verilog:`negedge` ``1`` ``1`` ``0`` $_DFFE_NP1N_, $_SDFFE_NP1N_, $_SDFFCE_NP1N_
|
||
:verilog:`negedge` ``1`` ``1`` ``1`` $_DFFE_NP1P_, $_SDFFE_NP1P_, $_SDFFCE_NP1P_
|
||
:verilog:`posedge` ``0`` ``0`` ``0`` $_DFFE_PN0N_, $_SDFFE_PN0N_, $_SDFFCE_PN0N_
|
||
:verilog:`posedge` ``0`` ``0`` ``1`` $_DFFE_PN0P_, $_SDFFE_PN0P_, $_SDFFCE_PN0P_
|
||
:verilog:`posedge` ``0`` ``1`` ``0`` $_DFFE_PN1N_, $_SDFFE_PN1N_, $_SDFFCE_PN1N_
|
||
:verilog:`posedge` ``0`` ``1`` ``1`` $_DFFE_PN1P_, $_SDFFE_PN1P_, $_SDFFCE_PN1P_
|
||
:verilog:`posedge` ``1`` ``0`` ``0`` $_DFFE_PP0N_, $_SDFFE_PP0N_, $_SDFFCE_PP0N_
|
||
:verilog:`posedge` ``1`` ``0`` ``1`` $_DFFE_PP0P_, $_SDFFE_PP0P_, $_SDFFCE_PP0P_
|
||
:verilog:`posedge` ``1`` ``1`` ``0`` $_DFFE_PP1N_, $_SDFFE_PP1N_, $_SDFFCE_PP1N_
|
||
:verilog:`posedge` ``1`` ``1`` ``1`` $_DFFE_PP1P_, $_SDFFE_PP1P_, $_SDFFCE_PP1P_
|
||
================== ============== ============== ============= ===========================================
|
||
|
||
.. table:: Cell types for gate level logic networks (FFs with set and reset)
|
||
:name: tab:CellLib_gates_dffsr
|
||
|
||
================== ============== ============== ============
|
||
:math:`ClkEdge` :math:`SetLvl` :math:`RstLvl` Cell Type
|
||
================== ============== ============== ============
|
||
:verilog:`negedge` ``0`` ``0`` $_DFFSR_NNN_
|
||
:verilog:`negedge` ``0`` ``1`` $_DFFSR_NNP_
|
||
:verilog:`negedge` ``1`` ``0`` $_DFFSR_NPN_
|
||
:verilog:`negedge` ``1`` ``1`` $_DFFSR_NPP_
|
||
:verilog:`posedge` ``0`` ``0`` $_DFFSR_PNN_
|
||
:verilog:`posedge` ``0`` ``1`` $_DFFSR_PNP_
|
||
:verilog:`posedge` ``1`` ``0`` $_DFFSR_PPN_
|
||
:verilog:`posedge` ``1`` ``1`` $_DFFSR_PPP_
|
||
================== ============== ============== ============
|
||
|
||
|
||
.. table:: Cell types for gate level logic networks (FFs with set and reset and enable)
|
||
:name: tab:CellLib_gates_dffsre
|
||
|
||
================== ============== ============== ============= ==============
|
||
:math:`ClkEdge` :math:`SetLvl` :math:`RstLvl` :math:`EnLvl` Cell Type
|
||
================== ============== ============== ============= ==============
|
||
:verilog:`negedge` ``0`` ``0`` ``0`` $_DFFSRE_NNNN_
|
||
:verilog:`negedge` ``0`` ``0`` ``1`` $_DFFSRE_NNNP_
|
||
:verilog:`negedge` ``0`` ``1`` ``0`` $_DFFSRE_NNPN_
|
||
:verilog:`negedge` ``0`` ``1`` ``1`` $_DFFSRE_NNPP_
|
||
:verilog:`negedge` ``1`` ``0`` ``0`` $_DFFSRE_NPNN_
|
||
:verilog:`negedge` ``1`` ``0`` ``1`` $_DFFSRE_NPNP_
|
||
:verilog:`negedge` ``1`` ``1`` ``0`` $_DFFSRE_NPPN_
|
||
:verilog:`negedge` ``1`` ``1`` ``1`` $_DFFSRE_NPPP_
|
||
:verilog:`posedge` ``0`` ``0`` ``0`` $_DFFSRE_PNNN_
|
||
:verilog:`posedge` ``0`` ``0`` ``1`` $_DFFSRE_PNNP_
|
||
:verilog:`posedge` ``0`` ``1`` ``0`` $_DFFSRE_PNPN_
|
||
:verilog:`posedge` ``0`` ``1`` ``1`` $_DFFSRE_PNPP_
|
||
:verilog:`posedge` ``1`` ``0`` ``0`` $_DFFSRE_PPNN_
|
||
:verilog:`posedge` ``1`` ``0`` ``1`` $_DFFSRE_PPNP_
|
||
:verilog:`posedge` ``1`` ``1`` ``0`` $_DFFSRE_PPPN_
|
||
:verilog:`posedge` ``1`` ``1`` ``1`` $_DFFSRE_PPPP_
|
||
================== ============== ============== ============= ==============
|
||
|
||
|
||
.. table:: Cell types for gate level logic networks (latches with reset)
|
||
:name: tab:CellLib_gates_adlatch
|
||
|
||
============= ============== ============== =============
|
||
:math:`EnLvl` :math:`RstLvl` :math:`RstVal` Cell Type
|
||
============= ============== ============== =============
|
||
``0`` ``0`` ``0`` $_DLATCH_NN0_
|
||
``0`` ``0`` ``1`` $_DLATCH_NN1_
|
||
``0`` ``1`` ``0`` $_DLATCH_NP0_
|
||
``0`` ``1`` ``1`` $_DLATCH_NP1_
|
||
``1`` ``0`` ``0`` $_DLATCH_PN0_
|
||
``1`` ``0`` ``1`` $_DLATCH_PN1_
|
||
``1`` ``1`` ``0`` $_DLATCH_PP0_
|
||
``1`` ``1`` ``1`` $_DLATCH_PP1_
|
||
============= ============== ============== =============
|
||
|
||
|
||
.. table:: Cell types for gate level logic networks (latches with set and reset)
|
||
:name: tab:CellLib_gates_dlatchsr
|
||
|
||
============= ============== ============== ===============
|
||
:math:`EnLvl` :math:`SetLvl` :math:`RstLvl` Cell Type
|
||
============= ============== ============== ===============
|
||
``0`` ``0`` ``0`` $_DLATCHSR_NNN_
|
||
``0`` ``0`` ``1`` $_DLATCHSR_NNP_
|
||
``0`` ``1`` ``0`` $_DLATCHSR_NPN_
|
||
``0`` ``1`` ``1`` $_DLATCHSR_NPP_
|
||
``1`` ``0`` ``0`` $_DLATCHSR_PNN_
|
||
``1`` ``0`` ``1`` $_DLATCHSR_PNP_
|
||
``1`` ``1`` ``0`` $_DLATCHSR_PPN_
|
||
``1`` ``1`` ``1`` $_DLATCHSR_PPP_
|
||
============= ============== ============== ===============
|
||
|
||
|
||
|
||
.. table:: Cell types for gate level logic networks (SR latches)
|
||
:name: tab:CellLib_gates_sr
|
||
|
||
============== ============== =========
|
||
:math:`SetLvl` :math:`RstLvl` Cell Type
|
||
============== ============== =========
|
||
``0`` ``0`` $_SR_NN_
|
||
``0`` ``1`` $_SR_NP_
|
||
``1`` ``0`` $_SR_PN_
|
||
``1`` ``1`` $_SR_PP_
|
||
============== ============== =========
|
||
|
||
|
||
Tables \ :numref:`%s <tab:CellLib_gates>`, :numref:`%s
|
||
<tab:CellLib_gates_dffe>`, :numref:`%s <tab:CellLib_gates_adff>`, :numref:`%s
|
||
<tab:CellLib_gates_adffe>`, :numref:`%s <tab:CellLib_gates_dffsr>`, :numref:`%s
|
||
<tab:CellLib_gates_dffsre>`, :numref:`%s <tab:CellLib_gates_adlatch>`,
|
||
:numref:`%s <tab:CellLib_gates_dlatchsr>` and :numref:`%s
|
||
<tab:CellLib_gates_sr>` list all cell types used for gate level logic. The cell
|
||
types ``$_BUF_``, ``$_NOT_``, ``$_AND_``, ``$_NAND_``, ``$_ANDNOT_``, ``$_OR_``,
|
||
``$_NOR_``, ``$_ORNOT_``, ``$_XOR_``, ``$_XNOR_``, ``$_AOI3_``, ``$_OAI3_``,
|
||
``$_AOI4_``, ``$_OAI4_``, ``$_MUX_``, ``$_MUX4_``, ``$_MUX8_``, ``$_MUX16_`` and
|
||
``$_NMUX_`` are used to model combinatorial logic. The cell type ``$_TBUF_`` is
|
||
used to model tristate logic.
|
||
|
||
The ``$_MUX4_``, ``$_MUX8_`` and ``$_MUX16_`` cells are used to model wide
|
||
muxes, and correspond to the following Verilog code:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
// $_MUX4_
|
||
assign Y = T ? (S ? D : C) :
|
||
(S ? B : A);
|
||
// $_MUX8_
|
||
assign Y = U ? T ? (S ? H : G) :
|
||
(S ? F : E) :
|
||
T ? (S ? D : C) :
|
||
(S ? B : A);
|
||
// $_MUX16_
|
||
assign Y = V ? U ? T ? (S ? P : O) :
|
||
(S ? N : M) :
|
||
T ? (S ? L : K) :
|
||
(S ? J : I) :
|
||
U ? T ? (S ? H : G) :
|
||
(S ? F : E) :
|
||
T ? (S ? D : C) :
|
||
(S ? B : A);
|
||
|
||
The cell types ``$_DFF_N_`` and ``$_DFF_P_`` represent d-type flip-flops.
|
||
|
||
The cell types ``$_DFFE_[NP][NP]_`` implement d-type flip-flops with enable. The
|
||
values in the table for these cell types relate to the following Verilog code
|
||
template.
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C)
|
||
if (EN == EN_LVL)
|
||
Q <= D;
|
||
|
||
The cell types ``$_DFF_[NP][NP][01]_`` implement d-type flip-flops with
|
||
asynchronous reset. The values in the table for these cell types relate to the
|
||
following Verilog code template, where ``RST_EDGE`` is ``posedge`` if
|
||
``RST_LVL`` if ``1``, and ``negedge`` otherwise.
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C, RST_EDGE R)
|
||
if (R == RST_LVL)
|
||
Q <= RST_VAL;
|
||
else
|
||
Q <= D;
|
||
|
||
The cell types ``$_SDFF_[NP][NP][01]_`` implement d-type flip-flops with
|
||
synchronous reset. The values in the table for these cell types relate to the
|
||
following Verilog code template:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C)
|
||
if (R == RST_LVL)
|
||
Q <= RST_VAL;
|
||
else
|
||
Q <= D;
|
||
|
||
The cell types ``$_DFFE_[NP][NP][01][NP]_`` implement d-type flip-flops with
|
||
asynchronous reset and enable. The values in the table for these cell types
|
||
relate to the following Verilog code template, where ``RST_EDGE`` is
|
||
``posedge`` if ``RST_LVL`` if ``1``, and ``negedge`` otherwise.
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C, RST_EDGE R)
|
||
if (R == RST_LVL)
|
||
Q <= RST_VAL;
|
||
else if (EN == EN_LVL)
|
||
Q <= D;
|
||
|
||
The cell types ``$_SDFFE_[NP][NP][01][NP]_`` implement d-type flip-flops with
|
||
synchronous reset and enable, with reset having priority over enable. The values
|
||
in the table for these cell types relate to the following Verilog code template:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C)
|
||
if (R == RST_LVL)
|
||
Q <= RST_VAL;
|
||
else if (EN == EN_LVL)
|
||
Q <= D;
|
||
|
||
The cell types ``$_SDFFCE_[NP][NP][01][NP]_`` implement d-type flip-flops with
|
||
synchronous reset and enable, with enable having priority over reset. The values
|
||
in the table for these cell types relate to the following Verilog code template:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C)
|
||
if (EN == EN_LVL)
|
||
if (R == RST_LVL)
|
||
Q <= RST_VAL;
|
||
else
|
||
Q <= D;
|
||
|
||
The cell types ``$_DFFSR_[NP][NP][NP]_`` implement d-type flip-flops with
|
||
asynchronous set and reset. The values in the table for these cell types relate
|
||
to the following Verilog code template, where ``RST_EDGE`` is ``posedge`` if
|
||
``RST_LVL`` if ``1``, ``negedge`` otherwise, and ``SET_EDGE`` is ``posedge``
|
||
if ``SET_LVL`` if ``1``, ``negedge`` otherwise.
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C, RST_EDGE R, SET_EDGE S)
|
||
if (R == RST_LVL)
|
||
Q <= 0;
|
||
else if (S == SET_LVL)
|
||
Q <= 1;
|
||
else
|
||
Q <= D;
|
||
|
||
The cell types ``$_DFFSRE_[NP][NP][NP][NP]_`` implement d-type flip-flops with
|
||
asynchronous set and reset and enable. The values in the table for these cell
|
||
types relate to the following Verilog code template, where ``RST_EDGE`` is
|
||
``posedge`` if ``RST_LVL`` if ``1``, ``negedge`` otherwise, and ``SET_EDGE``
|
||
is ``posedge`` if ``SET_LVL`` if ``1``, ``negedge`` otherwise.
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @(CLK_EDGE C, RST_EDGE R, SET_EDGE S)
|
||
if (R == RST_LVL)
|
||
Q <= 0;
|
||
else if (S == SET_LVL)
|
||
Q <= 1;
|
||
else if (E == EN_LVL)
|
||
Q <= D;
|
||
|
||
The cell types ``$_DLATCH_N_`` and ``$_DLATCH_P_`` represent d-type latches.
|
||
|
||
The cell types ``$_DLATCH_[NP][NP][01]_`` implement d-type latches with reset.
|
||
The values in the table for these cell types relate to the following Verilog
|
||
code template:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @*
|
||
if (R == RST_LVL)
|
||
Q <= RST_VAL;
|
||
else if (E == EN_LVL)
|
||
Q <= D;
|
||
|
||
The cell types ``$_DLATCHSR_[NP][NP][NP]_`` implement d-type latches with set
|
||
and reset. The values in the table for these cell types relate to the following
|
||
Verilog code template:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @*
|
||
if (R == RST_LVL)
|
||
Q <= 0;
|
||
else if (S == SET_LVL)
|
||
Q <= 1;
|
||
else if (E == EN_LVL)
|
||
Q <= D;
|
||
|
||
The cell types ``$_SR_[NP][NP]_`` implement sr-type latches. The values in the
|
||
table for these cell types relate to the following Verilog code template:
|
||
|
||
.. code-block:: verilog
|
||
:force:
|
||
|
||
always @*
|
||
if (R == RST_LVL)
|
||
Q <= 0;
|
||
else if (S == SET_LVL)
|
||
Q <= 1;
|
||
|
||
In most cases gate level logic networks are created from RTL networks using the
|
||
techmap pass. The flip-flop cells from the gate level logic network can be
|
||
mapped to physical flip-flop cells from a Liberty file using the dfflibmap pass.
|
||
The combinatorial logic cells can be mapped to physical cells from a Liberty
|
||
file via ABC using the abc pass.
|
||
|
||
Add information about ``$slice`` and ``$concat`` cells.
|
||
|
||
Add information about ``$lut`` and ``$sop`` cells.
|
||
|
||
Add information about ``$alu``, ``$macc``, ``$fa``, and ``$lcu`` cells.
|