riscv
/
yosys
mirror of https://github.com/YosysHQ/yosys.git
1
0
Fork 0
Code Issues Projects Releases Wiki Activity
yosys/manual/command-reference-manual.tex

8922 lines
289 KiB
TeX
Raw Blame History

% Generated using the yosys 'help -write-tex-command-reference-manual' command.
\section{abc -- use ABC for technology mapping}
\label{cmd:abc}
\begin{lstlisting}[numbers=left,frame=single]
abc [options] [selection]
This pass uses the ABC tool [1] for technology mapping of yosys's internal gate
library to a target architecture.
-exe <command>
use the specified command instead of "<yosys-bindir>/yosys-abc" to execute ABC.
This can e.g. be used to call a specific version of ABC or a wrapper.
-script <file>
use the specified ABC script file instead of the default script.
if <file> starts with a plus sign (+), then the rest of the filename
string is interpreted as the command string to be passed to ABC. The
leading plus sign is removed and all commas (,) in the string are
replaced with blanks before the string is passed to ABC.
if no -script parameter is given, the following scripts are used:
for -liberty/-genlib without -constr:
strash; ifraig; scorr; dc2; dretime; strash; &get -n; &dch -f;
&nf {D}; &put
for -liberty/-genlib with -constr:
strash; ifraig; scorr; dc2; dretime; strash; &get -n; &dch -f;
&nf {D}; &put; buffer; upsize {D}; dnsize {D}; stime -p
for -lut/-luts (only one LUT size):
strash; ifraig; scorr; dc2; dretime; strash; dch -f; if; mfs2;
lutpack {S}
for -lut/-luts (different LUT sizes):
strash; ifraig; scorr; dc2; dretime; strash; dch -f; if; mfs2
for -sop:
strash; ifraig; scorr; dc2; dretime; strash; dch -f;
cover {I} {P}
otherwise:
strash; ifraig; scorr; dc2; dretime; strash; &get -n; &dch -f;
&nf {D}; &put
-fast
use different default scripts that are slightly faster (at the cost
of output quality):
for -liberty/-genlib without -constr:
strash; dretime; map {D}
for -liberty/-genlib with -constr:
strash; dretime; map {D}; buffer; upsize {D}; dnsize {D};
stime -p
for -lut/-luts:
strash; dretime; if
for -sop:
strash; dretime; cover {I} {P}
otherwise:
strash; dretime; map
-liberty <file>
generate netlists for the specified cell library (using the liberty
file format).
-genlib <file>
generate netlists for the specified cell library (using the SIS Genlib
file format).
-constr <file>
pass this file with timing constraints to ABC.
use with -liberty/-genlib.
a constr file contains two lines:
set_driving_cell <cell_name>
set_load <floating_point_number>
the set_driving_cell statement defines which cell type is assumed to
drive the primary inputs and the set_load statement sets the load in
femtofarads for each primary output.
-D <picoseconds>
set delay target. the string {D} in the default scripts above is
replaced by this option when used, and an empty string otherwise.
this also replaces 'dretime' with 'dretime; retime -o {D}' in the
default scripts above.
-I <num>
maximum number of SOP inputs.
(replaces {I} in the default scripts above)
-P <num>
maximum number of SOP products.
(replaces {P} in the default scripts above)
-S <num>
maximum number of LUT inputs shared.
(replaces {S} in the default scripts above, default: -S 1)
-lut <width>
generate netlist using luts of (max) the specified width.
-lut <w1>:<w2>
generate netlist using luts of (max) the specified width <w2>. All
luts with width <= <w1> have constant cost. for luts larger than <w1>
the area cost doubles with each additional input bit. the delay cost
is still constant for all lut widths.
-luts <cost1>,<cost2>,<cost3>,<sizeN>:<cost4-N>,..
generate netlist using luts. Use the specified costs for luts with 1,
2, 3, .. inputs.
-sop
map to sum-of-product cells and inverters
-g type1,type2,...
Map to the specified list of gate types. Supported gates types are:
AND, NAND, OR, NOR, XOR, XNOR, ANDNOT, ORNOT, MUX,
NMUX, AOI3, OAI3, AOI4, OAI4.
(The NOT gate is always added to this list automatically.)
The following aliases can be used to reference common sets of gate types:
simple: AND OR XOR MUX
cmos2: NAND NOR
cmos3: NAND NOR AOI3 OAI3
cmos4: NAND NOR AOI3 OAI3 AOI4 OAI4
cmos: NAND NOR AOI3 OAI3 AOI4 OAI4 NMUX MUX XOR XNOR
gates: AND NAND OR NOR XOR XNOR ANDNOT ORNOT
aig: AND NAND OR NOR ANDNOT ORNOT
The alias 'all' represent the full set of all gate types.
Prefix a gate type with a '-' to remove it from the list. For example
the arguments 'AND,OR,XOR' and 'simple,-MUX' are equivalent.
The default is 'all,-NMUX,-AOI3,-OAI3,-AOI4,-OAI4'.
-dff
also pass $_DFF_?_ and $_DFFE_??_ cells through ABC. modules with many
clock domains are automatically partitioned in clock domains and each
domain is passed through ABC independently.
-clk [!]<clock-signal-name>[,[!]<enable-signal-name>]
use only the specified clock domain. this is like -dff, but only FF
cells that belong to the specified clock domain are used.
-keepff
set the "keep" attribute on flip-flop output wires. (and thus preserve
them, for example for equivalence checking.)
-nocleanup
when this option is used, the temporary files created by this pass
are not removed. this is useful for debugging.
-showtmp
print the temp dir name in log. usually this is suppressed so that the
command output is identical across runs.
-markgroups
set a 'abcgroup' attribute on all objects created by ABC. The value of
this attribute is a unique integer for each ABC process started. This
is useful for debugging the partitioning of clock domains.
-dress
run the 'dress' command after all other ABC commands. This aims to
preserve naming by an equivalence check between the original and post-ABC
netlists (experimental).
When no target cell library is specified the Yosys standard cell library is
loaded into ABC before the ABC script is executed.
Note that this is a logic optimization pass within Yosys that is calling ABC
internally. This is not going to "run ABC on your design". It will instead run
ABC on logic snippets extracted from your design. You will not get any useful
output when passing an ABC script that writes a file. Instead write your full
design as BLIF file with write_blif and then load that into ABC externally if
you want to use ABC to convert your design into another format.
[1] http://www.eecs.berkeley.edu/~alanmi/abc/
\end{lstlisting}
\section{abc9 -- use ABC9 for technology mapping}
\label{cmd:abc9}
\begin{lstlisting}[numbers=left,frame=single]
abc9 [options] [selection]
This script pass performs a sequence of commands to facilitate the use of the ABC
tool [1] for technology mapping of the current design to a target FPGA
architecture. Only fully-selected modules are supported.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-exe <command>
use the specified command instead of "<yosys-bindir>/yosys-abc" to execute ABC.
This can e.g. be used to call a specific version of ABC or a wrapper.
-script <file>
use the specified ABC script file instead of the default script.
if <file> starts with a plus sign (+), then the rest of the filename
string is interpreted as the command string to be passed to ABC. The
leading plus sign is removed and all commas (,) in the string are
replaced with blanks before the string is passed to ABC.
if no -script parameter is given, the following scripts are used:
&scorr; &sweep; &dc2; &dch -f; &ps; &if {C} {W} {D} {R} -v; &mfs
-fast
use different default scripts that are slightly faster (at the cost
of output quality):
&if {C} {W} {D} {R} -v
-D <picoseconds>
set delay target. the string {D} in the default scripts above is
replaced by this option when used, and an empty string otherwise
(indicating best possible delay).
-lut <width>
generate netlist using luts of (max) the specified width.
-lut <w1>:<w2>
generate netlist using luts of (max) the specified width <w2>. All
luts with width <= <w1> have constant cost. for luts larger than <w1>
the area cost doubles with each additional input bit. the delay cost
is still constant for all lut widths.
-lut <file>
pass this file with lut library to ABC.
-luts <cost1>,<cost2>,<cost3>,<sizeN>:<cost4-N>,..
generate netlist using luts. Use the specified costs for luts with 1,
2, 3, .. inputs.
-maxlut <width>
when auto-generating the lut library, discard all luts equal to or
greater than this size (applicable when neither -lut nor -luts is
specified).
-dff
also pass $_DFF_[NP]_ cells through to ABC. modules with many clock
domains are supported and automatically partitioned by ABC.
-nocleanup
when this option is used, the temporary files created by this pass
are not removed. this is useful for debugging.
-showtmp
print the temp dir name in log. usually this is suppressed so that the
command output is identical across runs.
-box <file>
pass this file with box library to ABC.
Note that this is a logic optimization pass within Yosys that is calling ABC
internally. This is not going to "run ABC on your design". It will instead run
ABC on logic snippets extracted from your design. You will not get any useful
output when passing an ABC script that writes a file. Instead write your full
design as an XAIGER file with `write_xaiger' and then load that into ABC
externally if you want to use ABC to convert your design into another format.
[1] http://www.eecs.berkeley.edu/~alanmi/abc/
check:
abc9_ops -check [-dff] (option if -dff)
map:
abc9_ops -prep_hier [-dff] (option if -dff)
scc -specify -set_attr abc9_scc_id {}
abc9_ops -prep_bypass [-prep_dff] (option if -dff)
design -stash $abc9
design -load $abc9_map
proc
wbflip
techmap -wb -map %$abc9 -map +/techmap.v A:abc9_flop
opt -nodffe -nosdff
abc9_ops -prep_dff_submod (only if -dff)
setattr -set submod "$abc9_flop" t:$_DFF_?_ %ci* %co* t:$_DFF_?_ %d (only if -dff)
submod (only if -dff)
setattr -mod -set whitebox 1 -set abc9_flop 1 -set abc9_box 1 *_$abc9_flop (only if -dff)
foreach module in design
rename <module-name>_$abc9_flop _TECHMAP_REPLACE_ (only if -dff)
abc9_ops -prep_dff_unmap (only if -dff)
design -copy-to $abc9 =*_$abc9_flop (only if -dff)
delete =*_$abc9_flop (only if -dff)
design -stash $abc9_map
design -load $abc9
design -delete $abc9
techmap -wb -max_iter 1 -map %$abc9_map -map +/abc9_map.v [-D DFF] (option if -dff)
design -delete $abc9_map
pre:
read_verilog -icells -lib -specify +/abc9_model.v
abc9_ops -break_scc -prep_delays -prep_xaiger [-dff] (option for -dff)
abc9_ops -prep_lut <maxlut> (skip if -lut or -luts)
abc9_ops -prep_box (skip if -box)
design -stash $abc9
design -load $abc9_holes
techmap -wb -map %$abc9 -map +/techmap.v
opt -purge
aigmap
design -stash $abc9_holes
design -load $abc9
design -delete $abc9
exe:
aigmap
foreach module in selection
abc9_ops -write_lut <abc-temp-dir>/input.lut (skip if '-lut' or '-luts')
abc9_ops -write_box <abc-temp-dir>/input.box (skip if '-box')
write_xaiger -map <abc-temp-dir>/input.sym [-dff] <abc-temp-dir>/input.xaig
abc9_exe [options] -cwd <abc-temp-dir> -lut [<abc-temp-dir>/input.lut] -box [<abc-temp-dir>/input.box]
read_aiger -xaiger -wideports -module_name <module-name>$abc9 -map <abc-temp-dir>/input.sym <abc-temp-dir>/output.aig
abc9_ops -reintegrate [-dff]
unmap:
techmap -wb -map %$abc9_unmap -map +/abc9_unmap.v
design -delete $abc9_unmap
design -delete $abc9_holes
delete =*_$abc9_byp
setattr -mod -unset abc9_box_id
\end{lstlisting}
\section{abc9\_exe -- use ABC9 for technology mapping}
\label{cmd:abc9_exe}
\begin{lstlisting}[numbers=left,frame=single]
abc9_exe [options]
This pass uses the ABC tool [1] for technology mapping of the top module
(according to the (* top *) attribute or if only one module is currently selected)
to a target FPGA architecture.
-exe <command>
use the specified command instead of "<yosys-bindir>/yosys-abc" to execute ABC.
This can e.g. be used to call a specific version of ABC or a wrapper.
-script <file>
use the specified ABC script file instead of the default script.
if <file> starts with a plus sign (+), then the rest of the filename
string is interpreted as the command string to be passed to ABC. The
leading plus sign is removed and all commas (,) in the string are
replaced with blanks before the string is passed to ABC.
if no -script parameter is given, the following scripts are used:
&scorr; &sweep; &dc2; &dch -f; &ps; &if {C} {W} {D} {R} -v; &mfs
-fast
use different default scripts that are slightly faster (at the cost
of output quality):
&if {C} {W} {D} {R} -v
-D <picoseconds>
set delay target. the string {D} in the default scripts above is
replaced by this option when used, and an empty string otherwise
(indicating best possible delay).
-lut <width>
generate netlist using luts of (max) the specified width.
-lut <w1>:<w2>
generate netlist using luts of (max) the specified width <w2>. All
luts with width <= <w1> have constant cost. for luts larger than <w1>
the area cost doubles with each additional input bit. the delay cost
is still constant for all lut widths.
-lut <file>
pass this file with lut library to ABC.
-luts <cost1>,<cost2>,<cost3>,<sizeN>:<cost4-N>,..
generate netlist using luts. Use the specified costs for luts with 1,
2, 3, .. inputs.
-showtmp
print the temp dir name in log. usually this is suppressed so that the
command output is identical across runs.
-box <file>
pass this file with box library to ABC.
-cwd <dir>
use this as the current working directory, inside which the 'input.xaig'
file is expected. temporary files will be created in this directory, and
the mapped result will be written to 'output.aig'.
Note that this is a logic optimization pass within Yosys that is calling ABC
internally. This is not going to "run ABC on your design". It will instead run
ABC on logic snippets extracted from your design. You will not get any useful
output when passing an ABC script that writes a file. Instead write your full
design as BLIF file with write_blif and then load that into ABC externally if
you want to use ABC to convert your design into another format.
[1] http://www.eecs.berkeley.edu/~alanmi/abc/
\end{lstlisting}
\section{abc9\_ops -- helper functions for ABC9}
\label{cmd:abc9_ops}
\begin{lstlisting}[numbers=left,frame=single]
abc9_ops [options] [selection]
This pass contains a set of supporting operations for use during ABC technology
mapping, and is expected to be called in conjunction with other operations from
the `abc9' script pass. Only fully-selected modules are supported.
-check
check that the design is valid, e.g. (* abc9_box_id *) values are unique,
(* abc9_carry *) is only given for one input/output port, etc.
-prep_hier
derive all used (* abc9_box *) or (* abc9_flop *) (if -dff option)
whitebox modules. with (* abc9_flop *) modules, only those containing
$dff/$_DFF_[NP]_ cells with zero initial state -- due to an ABC limitation
-- will be derived.
-prep_bypass
create techmap rules in the '$abc9_map' and '$abc9_unmap' designs for
bypassing sequential (* abc9_box *) modules using a combinatorial box
(named *_$abc9_byp). bypassing is necessary if sequential elements (e.g.
$dff, $mem, etc.) are discovered inside so that any combinatorial paths
will be correctly captured. this bypass box will only contain ports that
are referenced by a simple path declaration ($specify2 cell) inside a
specify block.
-prep_dff
select all (* abc9_flop *) modules instantiated in the design and store
in the named selection '$abc9_flops'.
-prep_dff_submod
within (* abc9_flop *) modules, rewrite all edge-sensitive path
declarations and $setup() timing checks ($specify3 and $specrule cells)
that share a 'DST' port with the $_DFF_[NP]_.Q port from this 'Q' port to
the DFF's 'D' port. this is to prepare such specify cells to be moved
into the flop box.
-prep_dff_unmap
populate the '$abc9_unmap' design with techmap rules for mapping *_$abc9_flop
cells back into their derived cell types (where the rules created by
-prep_hier will then map back to the original cell with parameters).
-prep_delays
insert `$__ABC9_DELAY' blackbox cells into the design to account for
certain required times.
-break_scc
for an arbitrarily chosen cell in each unique SCC of each selected module
(tagged with an (* abc9_scc_id = <int> *) attribute) interrupt all wires
driven by this cell's outputs with a temporary $__ABC9_SCC_BREAKER cell
to break the SCC.
-prep_xaiger
prepare the design for XAIGER output. this includes computing the
topological ordering of ABC9 boxes, as well as preparing the '$abc9_holes'
design that contains the logic behaviour of ABC9 whiteboxes.
-dff
consider flop cells (those instantiating modules marked with (* abc9_flop *))
during -prep_{delays,xaiger,box}.
-prep_lut <maxlut>
pre-compute the lut library by analysing all modules marked with
(* abc9_lut=<area> *).
-write_lut <dst>
write the pre-computed lut library to <dst>.
-prep_box
pre-compute the box library by analysing all modules marked with
(* abc9_box *).
-write_box <dst>
write the pre-computed box library to <dst>.
-reintegrate
for each selected module, re-intergrate the module '<module-name>$abc9'
by first recovering ABC9 boxes, and then stitching in the remaining primary
inputs and outputs.
\end{lstlisting}
\section{add -- add objects to the design}
\label{cmd:add}
\begin{lstlisting}[numbers=left,frame=single]
add <command> [selection]
This command adds objects to the design. It operates on all fully selected
modules. So e.g. 'add -wire foo' will add a wire foo to all selected modules.
add {-wire|-input|-inout|-output} <name> <width> [selection]
Add a wire (input, inout, output port) with the given name and width. The
command will fail if the object exists already and has different properties
than the object to be created.
add -global_input <name> <width> [selection]
Like 'add -input', but also connect the signal between instances of the
selected modules.
add {-assert|-assume|-live|-fair|-cover} <name1> [-if <name2>]
Add an $assert, $assume, etc. cell connected to a wire named name1, with its
enable signal optionally connected to a wire named name2 (default: 1'b1).
add -mod <name[s]>
Add module[s] with the specified name[s].
\end{lstlisting}
\section{aigmap -- map logic to and-inverter-graph circuit}
\label{cmd:aigmap}
\begin{lstlisting}[numbers=left,frame=single]
aigmap [options] [selection]
Replace all logic cells with circuits made of only $_AND_ and
$_NOT_ cells.
-nand
Enable creation of $_NAND_ cells
-select
Overwrite replaced cells in the current selection with new $_AND_,
$_NOT_, and $_NAND_, cells
\end{lstlisting}
\section{alumacc -- extract ALU and MACC cells}
\label{cmd:alumacc}
\begin{lstlisting}[numbers=left,frame=single]
alumacc [selection]
This pass translates arithmetic operations like $add, $mul, $lt, etc. to $alu
and $macc cells.
\end{lstlisting}
\section{anlogic\_eqn -- Anlogic: Calculate equations for luts}
\label{cmd:anlogic_eqn}
\begin{lstlisting}[numbers=left,frame=single]
anlogic_eqn [selection]
Calculate equations for luts since bitstream generator depends on it.
\end{lstlisting}
\section{anlogic\_fixcarry -- Anlogic: fix carry chain}
\label{cmd:anlogic_fixcarry}
\begin{lstlisting}[numbers=left,frame=single]
anlogic_fixcarry [options] [selection]
Add Anlogic adders to fix carry chain if needed.
\end{lstlisting}
\section{assertpmux -- adds asserts for parallel muxes}
\label{cmd:assertpmux}
\begin{lstlisting}[numbers=left,frame=single]
assertpmux [options] [selection]
This command adds asserts to the design that assert that all parallel muxes
($pmux cells) have a maximum of one of their inputs enable at any time.
-noinit
do not enforce the pmux condition during the init state
-always
usually the $pmux condition is only checked when the $pmux output
is used by the mux tree it drives. this option will deactivate this
additional constraint and check the $pmux condition always.
\end{lstlisting}
\section{async2sync -- convert async FF inputs to sync circuits}
\label{cmd:async2sync}
\begin{lstlisting}[numbers=left,frame=single]
async2sync [options] [selection]
This command replaces async FF inputs with sync circuits emulating the same
behavior for when the async signals are actually synchronized to the clock.
This pass assumes negative hold time for the async FF inputs. For example when
a reset deasserts with the clock edge, then the FF output will still drive the
reset value in the next cycle regardless of the data-in value at the time of
the clock edge.
\end{lstlisting}
\section{attrmap -- renaming attributes}
\label{cmd:attrmap}
\begin{lstlisting}[numbers=left,frame=single]
attrmap [options] [selection]
This command renames attributes and/or maps key/value pairs to
other key/value pairs.
-tocase <name>
Match attribute names case-insensitively and set it to the specified
name.
-rename <old_name> <new_name>
Rename attributes as specified
-map <old_name>=<old_value> <new_name>=<new_value>
Map key/value pairs as indicated.
-imap <old_name>=<old_value> <new_name>=<new_value>
Like -map, but use case-insensitive match for <old_value> when
it is a string value.
-remove <name>=<value>
Remove attributes matching this pattern.
-modattr
Operate on module attributes instead of attributes on wires and cells.
For example, mapping Xilinx-style "keep" attributes to Yosys-style:
attrmap -tocase keep -imap keep="true" keep=1 \
-imap keep="false" keep=0 -remove keep=0
\end{lstlisting}
\section{attrmvcp -- move or copy attributes from wires to driving cells}
\label{cmd:attrmvcp}
\begin{lstlisting}[numbers=left,frame=single]
attrmvcp [options] [selection]
Move or copy attributes on wires to the cells driving them.
-copy
By default, attributes are moved. This will only add
the attribute to the cell, without removing it from
the wire.
-purge
If no selected cell consumes the attribute, then it is
left on the wire by default. This option will cause the
attribute to be removed from the wire, even if no selected
cell takes it.
-driven
By default, attriburtes are moved to the cell driving the
wire. With this option set it will be moved to the cell
driven by the wire instead.
-attr <attrname>
Move or copy this attribute. This option can be used
multiple times.
\end{lstlisting}
\section{autoname -- automatically assign names to objects}
\label{cmd:autoname}
\begin{lstlisting}[numbers=left,frame=single]
autoname [selection]
Assign auto-generated public names to objects with private names (the ones
with $-prefix).
\end{lstlisting}
\section{blackbox -- convert modules into blackbox modules}
\label{cmd:blackbox}
\begin{lstlisting}[numbers=left,frame=single]
blackbox [options] [selection]
Convert modules into blackbox modules (remove contents and set the blackbox
module attribute).
\end{lstlisting}
\section{bugpoint -- minimize testcases}
\label{cmd:bugpoint}
\begin{lstlisting}[numbers=left,frame=single]
bugpoint [options] [-script <filename> | -command "<command>"]
This command minimizes the current design that is known to crash Yosys with the
given script into a smaller testcase. It does this by removing an arbitrary part
of the design and recursively invokes a new Yosys process with this modified design
and the same script, repeating these steps while it can find a smaller design that
still causes a crash. Once this command finishes, it replaces the current design
with the smallest testcase it was able to produce.
In order to save the reduced testcase you must write this out to a file with
another command after `bugpoint` like `write_rtlil` or `write_verilog`.
-script <filename> | -command "<command>"
use this script file or command to crash Yosys. required.
-yosys <filename>
use this Yosys binary. if not specified, `yosys` is used.
-grep "<string>"
only consider crashes that place this string in the log file.
-fast
run `proc_clean; clean -purge` after each minimization step. converges
faster, but produces larger testcases, and may fail to produce any
testcase at all if the crash is related to dangling wires.
-clean
run `proc_clean; clean -purge` before checking testcase and after
finishing. produces smaller and more useful testcases, but may fail to
produce any testcase at all if the crash is related to dangling wires.
It is possible to constrain which parts of the design will be considered for
removal. Unless one or more of the following options are specified, all parts
will be considered.
-modules
try to remove modules. modules with a (* bugpoint_keep *) attribute
will be skipped.
-ports
try to remove module ports. ports with a (* bugpoint_keep *) attribute
will be skipped (useful for clocks, resets, etc.)
-cells
try to remove cells. cells with a (* bugpoint_keep *) attribute will
be skipped.
-connections
try to reconnect ports to 'x.
-processes
try to remove processes. processes with a (* bugpoint_keep *) attribute
will be skipped.
-assigns
try to remove process assigns from cases.
-updates
try to remove process updates from syncs.
-runner "<prefix>"
child process wrapping command, e.g., "timeout 30", or valgrind.
\end{lstlisting}
\section{cd -- a shortcut for 'select -module <name>'}
\label{cmd:cd}
\begin{lstlisting}[numbers=left,frame=single]
cd <modname>
This is just a shortcut for 'select -module <modname>'.
cd <cellname>
When no module with the specified name is found, but there is a cell
with the specified name in the current module, then this is equivalent
to 'cd <celltype>'.
cd ..
Remove trailing substrings that start with '.' in current module name until
the name of a module in the current design is generated, then switch to that
module. Otherwise clear the current selection.
cd
This is just a shortcut for 'select -clear'.
\end{lstlisting}
\section{check -- check for obvious problems in the design}
\label{cmd:check}
\begin{lstlisting}[numbers=left,frame=single]
check [options] [selection]
This pass identifies the following problems in the current design:
- combinatorial loops
- two or more conflicting drivers for one wire
- used wires that do not have a driver
Options:
-noinit
also check for wires which have the 'init' attribute set
-initdrv
also check for wires that have the 'init' attribute set and are not
driven by an FF cell type
-mapped
also check for internal cells that have not been mapped to cells of the
target architecture
-allow-tbuf
modify the -mapped behavior to still allow $_TBUF_ cells
-assert
produce a runtime error if any problems are found in the current design
\end{lstlisting}
\section{chformal -- change formal constraints of the design}
\label{cmd:chformal}
\begin{lstlisting}[numbers=left,frame=single]
chformal [types] [mode] [options] [selection]
Make changes to the formal constraints of the design. The [types] options
the type of constraint to operate on. If none of the following options are given,
the command will operate on all constraint types:
-assert $assert cells, representing assert(...) constraints
-assume $assume cells, representing assume(...) constraints
-live $live cells, representing assert(s_eventually ...)
-fair $fair cells, representing assume(s_eventually ...)
-cover $cover cells, representing cover() statements
Exactly one of the following modes must be specified:
-remove
remove the cells and thus constraints from the design
-early
bypass FFs that only delay the activation of a constraint
-delay <N>
delay activation of the constraint by <N> clock cycles
-skip <N>
ignore activation of the constraint in the first <N> clock cycles
-assert2assume
-assume2assert
-live2fair
-fair2live
change the roles of cells as indicated. these options can be combined
\end{lstlisting}
\section{chparam -- re-evaluate modules with new parameters}
\label{cmd:chparam}
\begin{lstlisting}[numbers=left,frame=single]
chparam [ -set name value ]... [selection]
Re-evaluate the selected modules with new parameters. String values must be
passed in double quotes (").
chparam -list [selection]
List the available parameters of the selected modules.
\end{lstlisting}
\section{chtype -- change type of cells in the design}
\label{cmd:chtype}
\begin{lstlisting}[numbers=left,frame=single]
chtype [options] [selection]
Change the types of cells in the design.
-set <type>
set the cell type to the given type
-map <old_type> <new_type>
change cells types that match <old_type> to <new_type>
\end{lstlisting}
\section{clean -- remove unused cells and wires}
\label{cmd:clean}
\begin{lstlisting}[numbers=left,frame=single]
clean [options] [selection]
This is identical to 'opt_clean', but less verbose.
When commands are separated using the ';;' token, this command will be executed
between the commands.
When commands are separated using the ';;;' token, this command will be executed
in -purge mode between the commands.
\end{lstlisting}
\section{clean\_zerowidth -- clean zero-width connections from the design}
\label{cmd:clean_zerowidth}
\begin{lstlisting}[numbers=left,frame=single]
clean_zerowidth [selection]
Fixes the selected cells and processes to contain no zero-width connections.
Depending on the cell type, this may be implemented by removing the connection,
widening it to 1-bit, or removing the cell altogether.
\end{lstlisting}
\section{clk2fflogic -- convert clocked FFs to generic \$ff cells}
\label{cmd:clk2fflogic}
\begin{lstlisting}[numbers=left,frame=single]
clk2fflogic [options] [selection]
This command replaces clocked flip-flops with generic $ff cells that use the
implicit global clock. This is useful for formal verification of designs with
multiple clocks.
\end{lstlisting}
\section{clkbufmap -- insert clock buffers on clock networks}
\label{cmd:clkbufmap}
\begin{lstlisting}[numbers=left,frame=single]
clkbufmap [options] [selection]
Inserts clock buffers between nets connected to clock inputs and their drivers.
In the absence of any selection, all wires without the 'clkbuf_inhibit'
attribute will be considered for clock buffer insertion.
Alternatively, to consider all wires without the 'buffer_type' attribute set to
'none' or 'bufr' one would specify:
'w:* a:buffer_type=none a:buffer_type=bufr %u %d'
as the selection.
-buf <celltype> <portname_out>:<portname_in>
Specifies the cell type to use for the clock buffers
and its port names. The first port will be connected to
the clock network sinks, and the second will be connected
to the actual clock source.
-inpad <celltype> <portname_out>:<portname_in>
If specified, a PAD cell of the given type is inserted on
clock nets that are also top module's inputs (in addition
to the clock buffer, if any).
At least one of -buf or -inpad should be specified.
\end{lstlisting}
\section{connect -- create or remove connections}
\label{cmd:connect}
\begin{lstlisting}[numbers=left,frame=single]
connect [-nomap] [-nounset] -set <lhs-expr> <rhs-expr>
Create a connection. This is equivalent to adding the statement 'assign
<lhs-expr> = <rhs-expr>;' to the Verilog input. Per default, all existing
drivers for <lhs-expr> are unconnected. This can be overwritten by using
the -nounset option.
connect [-nomap] -unset <expr>
Unconnect all existing drivers for the specified expression.
connect [-nomap] [-assert] -port <cell> <port> <expr>
Connect the specified cell port to the specified cell port.
Per default signal alias names are resolved and all signal names are mapped
the the signal name of the primary driver. Using the -nomap option deactivates
this behavior.
The connect command operates in one module only. Either only one module must
be selected or an active module must be set using the 'cd' command.
The -assert option verifies that the connection already exists, instead of
making it.
This command does not operate on module with processes.
\end{lstlisting}
\section{connect\_rpc -- connect to RPC frontend}
\label{cmd:connect_rpc}
\begin{lstlisting}[numbers=left,frame=single]
connect_rpc -exec <command> [args...]
connect_rpc -path <path>
Load modules using an out-of-process frontend.
-exec <command> [args...]
run <command> with arguments [args...]. send requests on stdin, read
responses from stdout.
-path <path>
connect to Unix domain socket at <path>. (Unix)
connect to bidirectional byte-type named pipe at <path>. (Windows)
A simple JSON-based, newline-delimited protocol is used for communicating with
the frontend. Yosys requests data from the frontend by sending exactly 1 line
of JSON. Frontend responds with data or error message by replying with exactly
1 line of JSON as well.
-> {"method": "modules"}
<- {"modules": ["<module-name>", ...]}
<- {"error": "<error-message>"}
request for the list of modules that can be derived by this frontend.
the 'hierarchy' command will call back into this frontend if a cell
with type <module-name> is instantiated in the design.
-> {"method": "derive", "module": "<module-name">, "parameters": {
"<param-name>": {"type": "[unsigned|signed|string|real]",
"value": "<param-value>"}, ...}}
<- {"frontend": "[rtlil|verilog|...]","source": "<source>"}}
<- {"error": "<error-message>"}
request for the module <module-name> to be derived for a specific set of
parameters. <param-name> starts with \ for named parameters, and with $
for unnamed parameters, which are numbered starting at 1.<param-value>
for integer parameters is always specified as a binary string of unlimited
precision. the <source> returned by the frontend is hygienically parsed
by a built-in Yosys <frontend>, allowing the RPC frontend to return any
convenient representation of the module. the derived module is cached,
so the response should be the same whenever the same set of parameters
is provided.
\end{lstlisting}
\section{connwrappers -- match width of input-output port pairs}
\label{cmd:connwrappers}
\begin{lstlisting}[numbers=left,frame=single]
connwrappers [options] [selection]
Wrappers are used in coarse-grain synthesis to wrap cells with smaller ports
in wrapper cells with a (larger) constant port size. I.e. the upper bits
of the wrapper output are signed/unsigned bit extended. This command uses this
knowledge to rewire the inputs of the driven cells to match the output of
the driving cell.
-signed <cell_type> <port_name> <width_param>
-unsigned <cell_type> <port_name> <width_param>
consider the specified signed/unsigned wrapper output
-port <cell_type> <port_name> <width_param> <sign_param>
use the specified parameter to decide if signed or unsigned
The options -signed, -unsigned, and -port can be specified multiple times.
\end{lstlisting}
\section{coolrunner2\_fixup -- insert necessary buffer cells for CoolRunner-II architecture}
\label{cmd:coolrunner2_fixup}
\begin{lstlisting}[numbers=left,frame=single]
coolrunner2_fixup [options] [selection]
Insert necessary buffer cells for CoolRunner-II architecture.
\end{lstlisting}
\section{coolrunner2\_sop -- break \$sop cells into ANDTERM/ORTERM cells}
\label{cmd:coolrunner2_sop}
\begin{lstlisting}[numbers=left,frame=single]
coolrunner2_sop [options] [selection]
Break $sop cells into ANDTERM/ORTERM cells.
\end{lstlisting}
\section{copy -- copy modules in the design}
\label{cmd:copy}
\begin{lstlisting}[numbers=left,frame=single]
copy old_name new_name
Copy the specified module. Note that selection patterns are not supported
by this command.
\end{lstlisting}
\section{cover -- print code coverage counters}
\label{cmd:cover}
\begin{lstlisting}[numbers=left,frame=single]
cover [options] [pattern]
Print the code coverage counters collected using the cover() macro in the Yosys
C++ code. This is useful to figure out what parts of Yosys are utilized by a
test bench.
-q
Do not print output to the normal destination (console and/or log file)
-o file
Write output to this file, truncate if exists.
-a file
Write output to this file, append if exists.
-d dir
Write output to a newly created file in the specified directory.
When one or more pattern (shell wildcards) are specified, then only counters
matching at least one pattern are printed.
It is also possible to instruct Yosys to print the coverage counters on program
exit to a file using environment variables:
YOSYS_COVER_DIR="{dir-name}" yosys {args}
This will create a file (with an auto-generated name) in this
directory and write the coverage counters to it.
YOSYS_COVER_FILE="{file-name}" yosys {args}
This will append the coverage counters to the specified file.
Hint: Use the following AWK command to consolidate Yosys coverage files:
gawk '{ p[$3] = $1; c[$3] += $2; } END { for (i in p)
printf "%-60s %10d %s\n", p[i], c[i], i; }' {files} | sort -k3
Coverage counters are only available in Yosys for Linux.
\end{lstlisting}
\section{cutpoint -- adds formal cut points to the design}
\label{cmd:cutpoint}
\begin{lstlisting}[numbers=left,frame=single]
cutpoint [options] [selection]
This command adds formal cut points to the design.
-undef
set cupoint nets to undef (x). the default behavior is to create a
$anyseq cell and drive the cutpoint net from that
\end{lstlisting}
\section{debug -- run command with debug log messages enabled}
\label{cmd:debug}
\begin{lstlisting}[numbers=left,frame=single]
debug cmd
Execute the specified command with debug log messages enabled
\end{lstlisting}
\section{delete -- delete objects in the design}
\label{cmd:delete}
\begin{lstlisting}[numbers=left,frame=single]
delete [selection]
Deletes the selected objects. This will also remove entire modules, if the
whole module is selected.
delete {-input|-output|-port} [selection]
Does not delete any object but removes the input and/or output flag on the
selected wires, thus 'deleting' module ports.
\end{lstlisting}
\section{deminout -- demote inout ports to input or output}
\label{cmd:deminout}
\begin{lstlisting}[numbers=left,frame=single]
deminout [options] [selection]
"Demote" inout ports to input or output ports, if possible.
\end{lstlisting}
\section{design -- save, restore and reset current design}
\label{cmd:design}
\begin{lstlisting}[numbers=left,frame=single]
design -reset
Clear the current design.
design -save <name>
Save the current design under the given name.
design -stash <name>
Save the current design under the given name and then clear the current design.
design -push
Push the current design to the stack and then clear the current design.
design -push-copy
Push the current design to the stack without clearing the current design.
design -pop
Reset the current design and pop the last design from the stack.
design -load <name>
Reset the current design and load the design previously saved under the given
name.
design -copy-from <name> [-as <new_mod_name>] <selection>
Copy modules from the specified design into the current one. The selection is
evaluated in the other design.
design -copy-to <name> [-as <new_mod_name>] [selection]
Copy modules from the current design into the specified one.
design -import <name> [-as <new_top_name>] [selection]
Import the specified design into the current design. The source design must
either have a selected top module or the selection must contain exactly one
module that is then used as top module for this command.
design -reset-vlog
The Verilog front-end remembers defined macros and top-level declarations
between calls to 'read_verilog'. This command resets this memory.
design -delete <name>
Delete the design previously saved under the given name.
\end{lstlisting}
\section{dffinit -- set INIT param on FF cells}
\label{cmd:dffinit}
\begin{lstlisting}[numbers=left,frame=single]
dffinit [options] [selection]
This pass sets an FF cell parameter to the the initial value of the net it
drives. (This is primarily used in FPGA flows.)
-ff <cell_name> <output_port> <init_param>
operate on the specified cell type. this option can be used
multiple times.
-highlow
use the string values "high" and "low" to represent a single-bit
initial value of 1 or 0. (multi-bit values are not supported in this
mode.)
-strinit <string for high> <string for low>
use string values in the command line to represent a single-bit
initial value of 1 or 0. (multi-bit values are not supported in this
mode.)
-noreinit
fail if the FF cell has already a defined initial value set in other
passes and the initial value of the net it drives is not equal to
the already defined initial value.
\end{lstlisting}
\section{dfflegalize -- convert FFs to types supported by the target}
\label{cmd:dfflegalize}
\begin{lstlisting}[numbers=left,frame=single]
dfflegalize [options] [selection]
Converts FFs to types supported by the target.
-cell <cell_type_pattern> <init_values>
specifies a supported group of FF cells. <cell_type_pattern>
is a yosys internal fine cell name, where ? characters can be
as a wildcard matching any character. <init_values> specifies
which initialization values these FF cells can support, and can
be one of:
- x (no init value supported)
- 0
- 1
- r (init value has to match reset value, only for some FF types)
- 01 (both 0 and 1 supported).
-mince <num>
specifies a minimum number of FFs that should be using any given
clock enable signal. If a clock enable signal doesn't meet this
threshold, it is unmapped into soft logic.
-minsrst <num>
specifies a minimum number of FFs that should be using any given
sync set/reset signal. If a sync set/reset signal doesn't meet this
threshold, it is unmapped into soft logic.
The following cells are supported by this pass (ie. will be ingested,
and can be specified as allowed targets):
- $_DFF_[NP]_
- $_DFFE_[NP][NP]_
- $_DFF_[NP][NP][01]_
- $_DFFE_[NP][NP][01][NP]_
- $_ALDFF_[NP][NP]_
- $_ALDFFE_[NP][NP][NP]_
- $_DFFSR_[NP][NP][NP]_
- $_DFFSRE_[NP][NP][NP][NP]_
- $_SDFF_[NP][NP][01]_
- $_SDFFE_[NP][NP][01][NP]_
- $_SDFFCE_[NP][NP][01][NP]_
- $_SR_[NP][NP]_
- $_DLATCH_[NP]_
- $_DLATCH_[NP][NP][01]_
- $_DLATCHSR_[NP][NP][NP]_
The following transformations are performed by this pass:
- upconversion from a less capable cell to a more capable cell, if the less capable cell is not supported (eg. dff -> dffe, or adff -> dffsr)
- unmapping FFs with clock enable (due to unsupported cell type or -mince)
- unmapping FFs with sync reset (due to unsupported cell type or -minsrst)
- adding inverters on the control pins (due to unsupported polarity)
- adding inverters on the D and Q pins and inverting the init/reset values
(due to unsupported init or reset value)
- converting sr into adlatch (by tying D to 1 and using E as set input)
- emulating unsupported dffsr cell by adff + adff + sr + mux
- emulating unsupported dlatchsr cell by adlatch + adlatch + sr + mux
- emulating adff when the (reset, init) value combination is unsupported by
dff + adff + dlatch + mux
- emulating adlatch when the (reset, init) value combination is unsupported by
- dlatch + adlatch + dlatch + mux
If the pass is unable to realize a given cell type (eg. adff when only plain dffis available), an error is raised.
\end{lstlisting}
\section{dfflibmap -- technology mapping of flip-flops}
\label{cmd:dfflibmap}
\begin{lstlisting}[numbers=left,frame=single]
dfflibmap [-prepare] [-map-only] [-info] -liberty <file> [selection]
Map internal flip-flop cells to the flip-flop cells in the technology
library specified in the given liberty file.
This pass may add inverters as needed. Therefore it is recommended to
first run this pass and then map the logic paths to the target technology.
When called with -prepare, this command will convert the internal FF cells
to the internal cell types that best match the cells found in the given
liberty file, but won't actually map them to the target cells.
When called with -map-only, this command will only map internal cell
types that are already of exactly the right type to match the target
cells, leaving remaining internal cells untouched.
When called with -info, this command will only print the target cell
list, along with their associated internal cell types, and the argumentsthat would be passed to the dfflegalize pass. The design will not be
changed.
\end{lstlisting}
\section{dffunmap -- unmap clock enable and synchronous reset from FFs}
\label{cmd:dffunmap}
\begin{lstlisting}[numbers=left,frame=single]
dffunmap [options] [selection]
This pass transforms FF types with clock enable and/or synchronous reset into
their base type (with neither clock enable nor sync reset) by emulating the clock
enable and synchronous reset with multiplexers on the cell input.
-ce-only
unmap only clock enables, leave synchronous resets alone.
-srst-only
unmap only synchronous resets, leave clock enables alone.
\end{lstlisting}
\section{dump -- print parts of the design in RTLIL format}
\label{cmd:dump}
\begin{lstlisting}[numbers=left,frame=single]
dump [options] [selection]
Write the selected parts of the design to the console or specified file in
RTLIL format.
-m
also dump the module headers, even if only parts of a single
module is selected
-n
only dump the module headers if the entire module is selected
-o <filename>
write to the specified file.
-a <filename>
like -outfile but append instead of overwrite
\end{lstlisting}
\section{echo -- turning echoing back of commands on and off}
\label{cmd:echo}
\begin{lstlisting}[numbers=left,frame=single]
echo on
Print all commands to log before executing them.
echo off
Do not print all commands to log before executing them. (default)
\end{lstlisting}
\section{ecp5\_gsr -- ECP5: handle GSR}
\label{cmd:ecp5_gsr}
\begin{lstlisting}[numbers=left,frame=single]
ecp5_gsr [options] [selection]
Trim active low async resets connected to GSR and resolve GSR parameter,
if a GSR or SGSR primitive is used in the design.
If any cell has the GSR parameter set to "AUTO", this will be resolved
to "ENABLED" if a GSR primitive is present and the (* nogsr *) attribute
is not set, otherwise it will be resolved to "DISABLED".
\end{lstlisting}
\section{edgetypes -- list all types of edges in selection}
\label{cmd:edgetypes}
\begin{lstlisting}[numbers=left,frame=single]
edgetypes [options] [selection]
This command lists all unique types of 'edges' found in the selection. An 'edge'
is a 4-tuple of source and sink cell type and port name.
\end{lstlisting}
\section{efinix\_fixcarry -- Efinix: fix carry chain}
\label{cmd:efinix_fixcarry}
\begin{lstlisting}[numbers=left,frame=single]
efinix_fixcarry [options] [selection]
Add Efinix adders to fix carry chain if needed.
\end{lstlisting}
\section{equiv\_add -- add a \$equiv cell}
\label{cmd:equiv_add}
\begin{lstlisting}[numbers=left,frame=single]
equiv_add [-try] gold_sig gate_sig
This command adds an $equiv cell for the specified signals.
equiv_add [-try] -cell gold_cell gate_cell
This command adds $equiv cells for the ports of the specified cells.
\end{lstlisting}
\section{equiv\_induct -- proving \$equiv cells using temporal induction}
\label{cmd:equiv_induct}
\begin{lstlisting}[numbers=left,frame=single]
equiv_induct [options] [selection]
Uses a version of temporal induction to prove $equiv cells.
Only selected $equiv cells are proven and only selected cells are used to
perform the proof.
-undef
enable modelling of undef states
-seq <N>
the max. number of time steps to be considered (default = 4)
This command is very effective in proving complex sequential circuits, when
the internal state of the circuit quickly propagates to $equiv cells.
However, this command uses a weak definition of 'equivalence': This command
proves that the two circuits will not diverge after they produce equal
outputs (observable points via $equiv) for at least <N> cycles (the <N>
specified via -seq).
Combined with simulation this is very powerful because simulation can give
you confidence that the circuits start out synced for at least <N> cycles
after reset.
\end{lstlisting}
\section{equiv\_make -- prepare a circuit for equivalence checking}
\label{cmd:equiv_make}
\begin{lstlisting}[numbers=left,frame=single]
equiv_make [options] gold_module gate_module equiv_module
This creates a module annotated with $equiv cells from two presumably
equivalent modules. Use commands such as 'equiv_simple' and 'equiv_status'
to work with the created equivalent checking module.
-inames
Also match cells and wires with $... names.
-blacklist <file>
Do not match cells or signals that match the names in the file.
-encfile <file>
Match FSM encodings using the description from the file.
See 'help fsm_recode' for details.
Note: The circuit created by this command is not a miter (with something like
a trigger output), but instead uses $equiv cells to encode the equivalence
checking problem. Use 'miter -equiv' if you want to create a miter circuit.
\end{lstlisting}
\section{equiv\_mark -- mark equivalence checking regions}
\label{cmd:equiv_mark}
\begin{lstlisting}[numbers=left,frame=single]
equiv_mark [options] [selection]
This command marks the regions in an equivalence checking module. Region 0 is
the proven part of the circuit. Regions with higher numbers are connected
unproven subcricuits. The integer attribute 'equiv_region' is set on all
wires and cells.
\end{lstlisting}
\section{equiv\_miter -- extract miter from equiv circuit}
\label{cmd:equiv_miter}
\begin{lstlisting}[numbers=left,frame=single]
equiv_miter [options] miter_module [selection]
This creates a miter module for further analysis of the selected $equiv cells.
-trigger
Create a trigger output
-cmp
Create cmp_* outputs for individual unproven $equiv cells
-assert
Create a $assert cell for each unproven $equiv cell
-undef
Create compare logic that handles undefs correctly
\end{lstlisting}
\section{equiv\_opt -- prove equivalence for optimized circuit}
\label{cmd:equiv_opt}
\begin{lstlisting}[numbers=left,frame=single]
equiv_opt [options] [command]
This command uses temporal induction to check circuit equivalence before and
after an optimization pass.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to the start of the command list, and empty to
label is synonymous to the end of the command list.
-map <filename>
expand the modules in this file before proving equivalence. this is
useful for handling architecture-specific primitives.
-blacklist <file>
Do not match cells or signals that match the names in the file
(passed to equiv_make).
-assert
produce an error if the circuits are not equivalent.
-multiclock
run clk2fflogic before equivalence checking.
-async2sync
run async2sync before equivalence checking.
-undef
enable modelling of undef states during equiv_induct.
The following commands are executed by this verification command:
run_pass:
hierarchy -auto-top
design -save preopt
[command]
design -stash postopt
prepare:
design -copy-from preopt -as gold A:top
design -copy-from postopt -as gate A:top
techmap: (only with -map)
techmap -wb -D EQUIV -autoproc -map <filename> ...
prove:
clk2fflogic (only with -multiclock)
async2sync (only with -async2sync)
equiv_make -blacklist <filename> ... gold gate equiv
equiv_induct [-undef] equiv
equiv_status [-assert] equiv
restore:
design -load preopt
\end{lstlisting}
\section{equiv\_purge -- purge equivalence checking module}
\label{cmd:equiv_purge}
\begin{lstlisting}[numbers=left,frame=single]
equiv_purge [options] [selection]
This command removes the proven part of an equivalence checking module, leaving
only the unproven segments in the design. This will also remove and add module
ports as needed.
\end{lstlisting}
\section{equiv\_remove -- remove \$equiv cells}
\label{cmd:equiv_remove}
\begin{lstlisting}[numbers=left,frame=single]
equiv_remove [options] [selection]
This command removes the selected $equiv cells. If neither -gold nor -gate is
used then only proven cells are removed.
-gold
keep gold circuit
-gate
keep gate circuit
\end{lstlisting}
\section{equiv\_simple -- try proving simple \$equiv instances}
\label{cmd:equiv_simple}
\begin{lstlisting}[numbers=left,frame=single]
equiv_simple [options] [selection]
This command tries to prove $equiv cells using a simple direct SAT approach.
-v
verbose output
-undef
enable modelling of undef states
-short
create shorter input cones that stop at shared nodes. This yields
simpler SAT problems but sometimes fails to prove equivalence.
-nogroup
disabling grouping of $equiv cells by output wire
-seq <N>
the max. number of time steps to be considered (default = 1)
\end{lstlisting}
\section{equiv\_status -- print status of equivalent checking module}
\label{cmd:equiv_status}
\begin{lstlisting}[numbers=left,frame=single]
equiv_status [options] [selection]
This command prints status information for all selected $equiv cells.
-assert
produce an error if any unproven $equiv cell is found
\end{lstlisting}
\section{equiv\_struct -- structural equivalence checking}
\label{cmd:equiv_struct}
\begin{lstlisting}[numbers=left,frame=single]
equiv_struct [options] [selection]
This command adds additional $equiv cells based on the assumption that the
gold and gate circuit are structurally equivalent. Note that this can introduce
bad $equiv cells in cases where the netlists are not structurally equivalent,
for example when analyzing circuits with cells with commutative inputs. This
command will also de-duplicate gates.
-fwd
by default this command performans forward sweeps until nothing can
be merged by forwards sweeps, then backward sweeps until forward
sweeps are effective again. with this option set only forward sweeps
are performed.
-fwonly <cell_type>
add the specified cell type to the list of cell types that are only
merged in forward sweeps and never in backward sweeps. $equiv is in
this list automatically.
-icells
by default, the internal RTL and gate cell types are ignored. add
this option to also process those cell types with this command.
-maxiter <N>
maximum number of iterations to run before aborting
\end{lstlisting}
\section{eval -- evaluate the circuit given an input}
\label{cmd:eval}
\begin{lstlisting}[numbers=left,frame=single]
eval [options] [selection]
This command evaluates the value of a signal given the value of all required
inputs.
-set <signal> <value>
set the specified signal to the specified value.
-set-undef
set all unspecified source signals to undef (x)
-table <signal>
create a truth table using the specified input signals
-show <signal>
show the value for the specified signal. if no -show option is passed
then all output ports of the current module are used.
\end{lstlisting}
\section{exec -- execute commands in the operating system shell}
\label{cmd:exec}
\begin{lstlisting}[numbers=left,frame=single]
exec [options] -- [command]
Execute a command in the operating system shell. All supplied arguments are
concatenated and passed as a command to popen(3). Whitespace is not guaranteed
to be preserved, even if quoted. stdin and stderr are not connected, while stdout is
logged unless the "-q" option is specified.
-q
Suppress stdout and stderr from subprocess
-expect-return <int>
Generate an error if popen() does not return specified value.
May only be specified once; the final specified value is controlling
if specified multiple times.
-expect-stdout <regex>
Generate an error if the specified regex does not match any line
in subprocess's stdout. May be specified multiple times.
-not-expect-stdout <regex>
Generate an error if the specified regex matches any line
in subprocess's stdout. May be specified multiple times.
Example: exec -q -expect-return 0 -- echo "bananapie" | grep "nana"
\end{lstlisting}
\section{expose -- convert internal signals to module ports}
\label{cmd:expose}
\begin{lstlisting}[numbers=left,frame=single]
expose [options] [selection]
This command exposes all selected internal signals of a module as additional
outputs.
-dff
only consider wires that are directly driven by register cell.
-cut
when exposing a wire, create an input/output pair and cut the internal
signal path at that wire.
-input
when exposing a wire, create an input port and disconnect the internal
driver.
-shared
only expose those signals that are shared among the selected modules.
this is useful for preparing modules for equivalence checking.
-evert
also turn connections to instances of other modules to additional
inputs and outputs and remove the module instances.
-evert-dff
turn flip-flops to sets of inputs and outputs.
-sep <separator>
when creating new wire/port names, the original object name is suffixed
with this separator (default: '.') and the port name or a type
designator for the exposed signal.
\end{lstlisting}
\section{extract -- find subcircuits and replace them with cells}
\label{cmd:extract}
\begin{lstlisting}[numbers=left,frame=single]
extract -map <map_file> [options] [selection]
extract -mine <out_file> [options] [selection]
This pass looks for subcircuits that are isomorphic to any of the modules
in the given map file and replaces them with instances of this modules. The
map file can be a Verilog source file (*.v) or an RTLIL source file (*.il).
-map <map_file>
use the modules in this file as reference. This option can be used
multiple times.
-map %<design-name>
use the modules in this in-memory design as reference. This option can
be used multiple times.
-verbose
print debug output while analyzing
-constports
also find instances with constant drivers. this may be much
slower than the normal operation.
-nodefaultswaps
normally builtin port swapping rules for internal cells are used per
default. This turns that off, so e.g. 'a^b' does not match 'b^a'
when this option is used.
-compat <needle_type> <haystack_type>
Per default, the cells in the map file (needle) must have the
type as the cells in the active design (haystack). This option
can be used to register additional pairs of types that should
match. This option can be used multiple times.
-swap <needle_type> <port1>,<port2>[,...]
Register a set of swappable ports for a needle cell type.
This option can be used multiple times.
-perm <needle_type> <port1>,<port2>[,...] <portA>,<portB>[,...]
Register a valid permutation of swappable ports for a needle
cell type. This option can be used multiple times.
-cell_attr <attribute_name>
Attributes on cells with the given name must match.
-wire_attr <attribute_name>
Attributes on wires with the given name must match.
-ignore_parameters
Do not use parameters when matching cells.
-ignore_param <cell_type> <parameter_name>
Do not use this parameter when matching cells.
This pass does not operate on modules with unprocessed processes in it.
(I.e. the 'proc' pass should be used first to convert processes to netlists.)
This pass can also be used for mining for frequent subcircuits. In this mode
the following options are to be used instead of the -map option.
-mine <out_file>
mine for frequent subcircuits and write them to the given RTLIL file
-mine_cells_span <min> <max>
only mine for subcircuits with the specified number of cells
default value: 3 5
-mine_min_freq <num>
only mine for subcircuits with at least the specified number of matches
default value: 10
-mine_limit_matches_per_module <num>
when calculating the number of matches for a subcircuit, don't count
more than the specified number of matches per module
-mine_max_fanout <num>
don't consider internal signals with more than <num> connections
The modules in the map file may have the attribute 'extract_order' set to an
integer value. Then this value is used to determine the order in which the pass
tries to map the modules to the design (ascending, default value is 0).
See 'help techmap' for a pass that does the opposite thing.
\end{lstlisting}
\section{extract\_counter -- Extract GreenPak4 counter cells}
\label{cmd:extract_counter}
\begin{lstlisting}[numbers=left,frame=single]
extract_counter [options] [selection]
This pass converts non-resettable or async resettable down counters to
counter cells. Use a target-specific 'techmap' map file to convert those cells
to the actual target cells.
-maxwidth N
Only extract counters up to N bits wide (default 64)
-minwidth N
Only extract counters at least N bits wide (default 2)
-allow_arst yes|no
Allow counters to have async reset (default yes)
-dir up|down|both
Look for up-counters, down-counters, or both (default down)
-pout X,Y,...
Only allow parallel output from the counter to the listed cell types
(if not specified, parallel outputs are not restricted)
\end{lstlisting}
\section{extract\_fa -- find and extract full/half adders}
\label{cmd:extract_fa}
\begin{lstlisting}[numbers=left,frame=single]
extract_fa [options] [selection]
This pass extracts full/half adders from a gate-level design.
-fa, -ha
Enable cell types (fa=full adder, ha=half adder)
All types are enabled if none of this options is used
-d <int>
Set maximum depth for extracted logic cones (default=20)
-b <int>
Set maximum breadth for extracted logic cones (default=6)
-v
Verbose output
\end{lstlisting}
\section{extract\_reduce -- converts gate chains into \$reduce\_* cells}
\label{cmd:extract_reduce}
\begin{lstlisting}[numbers=left,frame=single]
extract_reduce [options] [selection]
converts gate chains into $reduce_* cells
This command finds chains of $_AND_, $_OR_, and $_XOR_ cells and replaces them
with their corresponding $reduce_* cells. Because this command only operates on
these cell types, it is recommended to map the design to only these cell types
using the `abc -g` command. Note that, in some cases, it may be more effective
to map the design to only $_AND_ cells, run extract_reduce, map the remaining
parts of the design to AND/OR/XOR cells, and run extract_reduce a second time.
-allow-off-chain
Allows matching of cells that have loads outside the chain. These cells
will be replicated and folded into the $reduce_* cell, but the original
cell will remain, driving its original loads.
\end{lstlisting}
\section{extractinv -- extract explicit inverter cells for invertible cell pins}
\label{cmd:extractinv}
\begin{lstlisting}[numbers=left,frame=single]
extractinv [options] [selection]
Searches the design for all cells with invertible pins controlled by a cell
parameter (eg. IS_CLK_INVERTED on many Xilinx cells) and removes the parameter.
If the parameter was set to 1, inserts an explicit inverter cell in front of
the pin instead. Normally used for output to ISE, which does not support the
inversion parameters.
To mark a cell port as invertible, use (* invertible_pin = "param_name" *)
on the wire in the blackbox module. The parameter value should have
the same width as the port, and will be effectively XORed with it.
-inv <celltype> <portname_out>:<portname_in>
Specifies the cell type to use for the inverters and its port names.
This option is required.
\end{lstlisting}
\section{flatten -- flatten design}
\label{cmd:flatten}
\begin{lstlisting}[numbers=left,frame=single]
flatten [options] [selection]
This pass flattens the design by replacing cells by their implementation. This
pass is very similar to the 'techmap' pass. The only difference is that this
pass is using the current design as mapping library.
Cells and/or modules with the 'keep_hierarchy' attribute set will not be
flattened by this command.
-wb
Ignore the 'whitebox' attribute on cell implementations.
\end{lstlisting}
\section{flowmap -- pack LUTs with FlowMap}
\label{cmd:flowmap}
\begin{lstlisting}[numbers=left,frame=single]
flowmap [options] [selection]
This pass uses the FlowMap technology mapping algorithm to pack logic gates
into k-LUTs with optimal depth. It allows mapping any circuit elements that can
be evaluated with the `eval` pass, including cells with multiple output ports
and multi-bit input and output ports.
-maxlut k
perform technology mapping for a k-LUT architecture. if not specified,
defaults to 3.
-minlut n
only produce n-input or larger LUTs. if not specified, defaults to 1.
-cells <cell>[,<cell>,...]
map specified cells. if not specified, maps $_NOT_, $_AND_, $_OR_,
$_XOR_ and $_MUX_, which are the outputs of the `simplemap` pass.
-relax
perform depth relaxation and area minimization.
-r-alpha n, -r-beta n, -r-gamma n
parameters of depth relaxation heuristic potential function.
if not specified, alpha=8, beta=2, gamma=1.
-optarea n
optimize for area by trading off at most n logic levels for fewer LUTs.
n may be zero, to optimize for area without increasing depth.
implies -relax.
-debug
dump intermediate graphs.
-debug-relax
explain decisions performed during depth relaxation.
\end{lstlisting}
\section{fmcombine -- combine two instances of a cell into one}
\label{cmd:fmcombine}
\begin{lstlisting}[numbers=left,frame=single]
fmcombine [options] module_name gold_cell gate_cell
This pass takes two cells, which are instances of the same module, and replaces
them with one instance of a special 'combined' module, that effectively
contains two copies of the original module, plus some formal properties.
This is useful for formal test benches that check what differences in behavior
a slight difference in input causes in a module.
-initeq
Insert assumptions that initially all FFs in both circuits have the
same initial values.
-anyeq
Do not duplicate $anyseq/$anyconst cells.
-fwd
Insert forward hint assumptions into the combined module.
-bwd
Insert backward hint assumptions into the combined module.
(Backward hints are logically equivalend to fordward hits, but
some solvers are faster with bwd hints, or even both -bwd and -fwd.)
-nop
Don't insert hint assumptions into the combined module.
(This should not provide any speedup over the original design, but
strangely sometimes it does.)
If none of -fwd, -bwd, and -nop is given, then -fwd is used as default.
\end{lstlisting}
\section{fminit -- set init values/sequences for formal}
\label{cmd:fminit}
\begin{lstlisting}[numbers=left,frame=single]
fminit [options] <selection>
This pass creates init constraints (for example for reset sequences) in a formal
model.
-seq <signal> <sequence>
Set sequence using comma-separated list of values, use 'z for
unconstrained bits. The last value is used for the remainder of the
trace.
-set <signal> <value>
Add constant value constraint
-posedge <signal>
-negedge <signal>
Set clock for init sequences
\end{lstlisting}
\section{freduce -- perform functional reduction}
\label{cmd:freduce}
\begin{lstlisting}[numbers=left,frame=single]
freduce [options] [selection]
This pass performs functional reduction in the circuit. I.e. if two nodes are
equivalent, they are merged to one node and one of the redundant drivers is
disconnected. A subsequent call to 'clean' will remove the redundant drivers.
-v, -vv
enable verbose or very verbose output
-inv
enable explicit handling of inverted signals
-stop <n>
stop after <n> reduction operations. this is mostly used for
debugging the freduce command itself.
-dump <prefix>
dump the design to <prefix>_<module>_<num>.il after each reduction
operation. this is mostly used for debugging the freduce command.
This pass is undef-aware, i.e. it considers don't-care values for detecting
equivalent nodes.
All selected wires are considered for rewiring. The selected cells cover the
circuit that is analyzed.
\end{lstlisting}
\section{fsm -- extract and optimize finite state machines}
\label{cmd:fsm}
\begin{lstlisting}[numbers=left,frame=single]
fsm [options] [selection]
This pass calls all the other fsm_* passes in a useful order. This performs
FSM extraction and optimization. It also calls opt_clean as needed:
fsm_detect unless got option -nodetect
fsm_extract
fsm_opt
opt_clean
fsm_opt
fsm_expand if got option -expand
opt_clean if got option -expand
fsm_opt if got option -expand
fsm_recode unless got option -norecode
fsm_info
fsm_export if got option -export
fsm_map unless got option -nomap
Options:
-expand, -norecode, -export, -nomap
enable or disable passes as indicated above
-fullexpand
call expand with -full option
-encoding type
-fm_set_fsm_file file
-encfile file
passed through to fsm_recode pass
\end{lstlisting}
\section{fsm\_detect -- finding FSMs in design}
\label{cmd:fsm_detect}
\begin{lstlisting}[numbers=left,frame=single]
fsm_detect [selection]
This pass detects finite state machines by identifying the state signal.
The state signal is then marked by setting the attribute 'fsm_encoding'
on the state signal to "auto".
Existing 'fsm_encoding' attributes are not changed by this pass.
Signals can be protected from being detected by this pass by setting the
'fsm_encoding' attribute to "none".
\end{lstlisting}
\section{fsm\_expand -- expand FSM cells by merging logic into it}
\label{cmd:fsm_expand}
\begin{lstlisting}[numbers=left,frame=single]
fsm_expand [-full] [selection]
The fsm_extract pass is conservative about the cells that belong to a finite
state machine. This pass can be used to merge additional auxiliary gates into
the finite state machine.
By default, fsm_expand is still a bit conservative regarding merging larger
word-wide cells. Call with -full to consider all cells for merging.
\end{lstlisting}
\section{fsm\_export -- exporting FSMs to KISS2 files}
\label{cmd:fsm_export}
\begin{lstlisting}[numbers=left,frame=single]
fsm_export [-noauto] [-o filename] [-origenc] [selection]
This pass creates a KISS2 file for every selected FSM. For FSMs with the
'fsm_export' attribute set, the attribute value is used as filename, otherwise
the module and cell name is used as filename. If the parameter '-o' is given,
the first exported FSM is written to the specified filename. This overwrites
the setting as specified with the 'fsm_export' attribute. All other FSMs are
exported to the default name as mentioned above.
-noauto
only export FSMs that have the 'fsm_export' attribute set
-o filename
filename of the first exported FSM
-origenc
use binary state encoding as state names instead of s0, s1, ...
\end{lstlisting}
\section{fsm\_extract -- extracting FSMs in design}
\label{cmd:fsm_extract}
\begin{lstlisting}[numbers=left,frame=single]
fsm_extract [selection]
This pass operates on all signals marked as FSM state signals using the
'fsm_encoding' attribute. It consumes the logic that creates the state signal
and uses the state signal to generate control signal and replaces it with an
FSM cell.
The generated FSM cell still generates the original state signal with its
original encoding. The 'fsm_opt' pass can be used in combination with the
'opt_clean' pass to eliminate this signal.
\end{lstlisting}
\section{fsm\_info -- print information on finite state machines}
\label{cmd:fsm_info}
\begin{lstlisting}[numbers=left,frame=single]
fsm_info [selection]
This pass dumps all internal information on FSM cells. It can be useful for
analyzing the synthesis process and is called automatically by the 'fsm'
pass so that this information is included in the synthesis log file.
\end{lstlisting}
\section{fsm\_map -- mapping FSMs to basic logic}
\label{cmd:fsm_map}
\begin{lstlisting}[numbers=left,frame=single]
fsm_map [selection]
This pass translates FSM cells to flip-flops and logic.
\end{lstlisting}
\section{fsm\_opt -- optimize finite state machines}
\label{cmd:fsm_opt}
\begin{lstlisting}[numbers=left,frame=single]
fsm_opt [selection]
This pass optimizes FSM cells. It detects which output signals are actually
not used and removes them from the FSM. This pass is usually used in
combination with the 'opt_clean' pass (see also 'help fsm').
\end{lstlisting}
\section{fsm\_recode -- recoding finite state machines}
\label{cmd:fsm_recode}
\begin{lstlisting}[numbers=left,frame=single]
fsm_recode [options] [selection]
This pass reassign the state encodings for FSM cells. At the moment only
one-hot encoding and binary encoding is supported.
-encoding <type>
specify the encoding scheme used for FSMs without the
'fsm_encoding' attribute or with the attribute set to `auto'.
-fm_set_fsm_file <file>
generate a file containing the mapping from old to new FSM encoding
in form of Synopsys Formality set_fsm_* commands.
-encfile <file>
write the mappings from old to new FSM encoding to a file in the
following format:
.fsm <module_name> <state_signal>
.map <old_bitpattern> <new_bitpattern>
\end{lstlisting}
\section{greenpak4\_dffinv -- merge greenpak4 inverters and DFF/latches}
\label{cmd:greenpak4_dffinv}
\begin{lstlisting}[numbers=left,frame=single]
greenpak4_dffinv [options] [selection]
Merge GP_INV cells with GP_DFF* and GP_DLATCH* cells.
\end{lstlisting}
\section{help -- display help messages}
\label{cmd:help}
\begin{lstlisting}[numbers=left,frame=single]
help ................ list all commands
help <command> ...... print help message for given command
help -all ........... print complete command reference
help -cells .......... list all cell types
help <celltype> ..... print help message for given cell type
help <celltype>+ .... print verilog code for given cell type
\end{lstlisting}
\section{hierarchy -- check, expand and clean up design hierarchy}
\label{cmd:hierarchy}
\begin{lstlisting}[numbers=left,frame=single]
hierarchy [-check] [-top <module>]
hierarchy -generate <cell-types> <port-decls>
In parametric designs, a module might exists in several variations with
different parameter values. This pass looks at all modules in the current
design and re-runs the language frontends for the parametric modules as
needed. It also resolves assignments to wired logic data types (wand/wor),
resolves positional module parameters, unrolls array instances, and more.
-check
also check the design hierarchy. this generates an error when
an unknown module is used as cell type.
-simcheck
like -check, but also throw an error if blackbox modules are
instantiated, and throw an error if the design has no top module.
-purge_lib
by default the hierarchy command will not remove library (blackbox)
modules. use this option to also remove unused blackbox modules.
-libdir <directory>
search for files named <module_name>.v in the specified directory
for unknown modules and automatically run read_verilog for each
unknown module.
-keep_positionals
per default this pass also converts positional arguments in cells
to arguments using port names. This option disables this behavior.
-keep_portwidths
per default this pass adjusts the port width on cells that are
module instances when the width does not match the module port. This
option disables this behavior.
-nodefaults
do not resolve input port default values
-nokeep_asserts
per default this pass sets the "keep" attribute on all modules
that directly or indirectly contain one or more formal properties.
This option disables this behavior.
-top <module>
use the specified top module to build the design hierarchy. Modules
outside this tree (unused modules) are removed.
when the -top option is used, the 'top' attribute will be set on the
specified top module. otherwise a module with the 'top' attribute set
will implicitly be used as top module, if such a module exists.
-auto-top
automatically determine the top of the design hierarchy and mark it.
-chparam name value
elaborate the top module using this parameter value. Modules on which
this parameter does not exist may cause a warning message to be output.
This option can be specified multiple times to override multiple
parameters. String values must be passed in double quotes (").
In -generate mode this pass generates blackbox modules for the given cell
types (wildcards supported). For this the design is searched for cells that
match the given types and then the given port declarations are used to
determine the direction of the ports. The syntax for a port declaration is:
{i|o|io}[@<num>]:<portname>
Input ports are specified with the 'i' prefix, output ports with the 'o'
prefix and inout ports with the 'io' prefix. The optional <num> specifies
the position of the port in the parameter list (needed when instantiated
using positional arguments). When <num> is not specified, the <portname> can
also contain wildcard characters.
This pass ignores the current selection and always operates on all modules
in the current design.
\end{lstlisting}
\section{hilomap -- technology mapping of constant hi- and/or lo-drivers}
\label{cmd:hilomap}
\begin{lstlisting}[numbers=left,frame=single]
hilomap [options] [selection]
Map constants to 'tielo' and 'tiehi' driver cells.
-hicell <celltype> <portname>
Replace constant hi bits with this cell.
-locell <celltype> <portname>
Replace constant lo bits with this cell.
-singleton
Create only one hi/lo cell and connect all constant bits
to that cell. Per default a separate cell is created for
each constant bit.
\end{lstlisting}
\section{history -- show last interactive commands}
\label{cmd:history}
\begin{lstlisting}[numbers=left,frame=single]
history
This command prints all commands in the shell history buffer. This are
all commands executed in an interactive session, but not the commands
from executed scripts.
\end{lstlisting}
\section{ice40\_braminit -- iCE40: perform SB\_RAM40\_4K initialization from file}
\label{cmd:ice40_braminit}
\begin{lstlisting}[numbers=left,frame=single]
ice40_braminit
This command processes all SB_RAM40_4K blocks with a non-empty INIT_FILE
parameter and converts it into the required INIT_x attributes
\end{lstlisting}
\section{ice40\_dsp -- iCE40: map multipliers}
\label{cmd:ice40_dsp}
\begin{lstlisting}[numbers=left,frame=single]
ice40_dsp [options] [selection]
Map multipliers ($mul/SB_MAC16) and multiply-accumulate ($mul/SB_MAC16 + $add)
cells into iCE40 DSP resources.
Currently, only the 16x16 multiply mode is supported and not the 2 x 8x8 mode.
Pack input registers (A, B, {C,D}; with optional hold), pipeline registers
({F,J,K,G}, H), output registers (O -- full 32-bits or lower 16-bits only; with
optional hold), and post-adder into into the SB_MAC16 resource.
Multiply-accumulate operations using the post-adder with feedback on the {C,D}
input will be folded into the DSP. In this scenario only, resetting the
the accumulator to an arbitrary value can be inferred to use the {C,D} input.
\end{lstlisting}
\section{ice40\_opt -- iCE40: perform simple optimizations}
\label{cmd:ice40_opt}
\begin{lstlisting}[numbers=left,frame=single]
ice40_opt [options] [selection]
This command executes the following script:
do
<ice40 specific optimizations>
opt_expr -mux_undef -undriven [-full]
opt_merge
opt_dff
opt_clean
while <changed design>
\end{lstlisting}
\section{ice40\_wrapcarry -- iCE40: wrap carries}
\label{cmd:ice40_wrapcarry}
\begin{lstlisting}[numbers=left,frame=single]
ice40_wrapcarry [selection]
Wrap manually instantiated SB_CARRY cells, along with their associated SB_LUT4s,
into an internal $__ICE40_CARRY_WRAPPER cell for preservation across technology
mapping.
Attributes on both cells will have their names prefixed with 'SB_CARRY.' or
'SB_LUT4.' and attached to the wrapping cell.
A (* keep *) attribute on either cell will be logically OR-ed together.
-unwrap
unwrap $__ICE40_CARRY_WRAPPER cells back into SB_CARRYs and SB_LUT4s,
including restoring their attributes.
\end{lstlisting}
\section{insbuf -- insert buffer cells for connected wires}
\label{cmd:insbuf}
\begin{lstlisting}[numbers=left,frame=single]
insbuf [options] [selection]
Insert buffer cells into the design for directly connected wires.
-buf <celltype> <in-portname> <out-portname>
Use the given cell type instead of $_BUF_. (Notice that the next
call to "clean" will remove all $_BUF_ in the design.)
\end{lstlisting}
\section{iopadmap -- technology mapping of i/o pads (or buffers)}
\label{cmd:iopadmap}
\begin{lstlisting}[numbers=left,frame=single]
iopadmap [options] [selection]
Map module inputs/outputs to PAD cells from a library. This pass
can only map to very simple PAD cells. Use 'techmap' to further map
the resulting cells to more sophisticated PAD cells.
-inpad <celltype> <in_port>[:<ext_port>]
Map module input ports to the given cell type with the
given output port name. if a 2nd portname is given, the
signal is passed through the pad call, using the 2nd
portname as the port facing the module port.
-outpad <celltype> <out_port>[:<ext_port>]
-inoutpad <celltype> <io_port>[:<ext_port>]
Similar to -inpad, but for output and inout ports.
-toutpad <celltype> <oe_port>:<out_port>[:<ext_port>]
Merges $_TBUF_ cells into the output pad cell. This takes precedence
over the other -outpad cell. The first portname is the enable input
of the tristate driver, which can be prefixed with `~` for negative
polarity enable.
-tinoutpad <celltype> <oe_port>:<in_port>:<out_port>[:<ext_port>]
Merges $_TBUF_ cells into the inout pad cell. This takes precedence
over the other -inoutpad cell. The first portname is the enable input
of the tristate driver and the 2nd portname is the internal output
buffering the external signal. Like with `-toutpad`, the enable can
be marked as negative polarity by prefixing the name with `~`.
-ignore <celltype> <portname>[:<portname>]*
Skips mapping inputs/outputs that are already connected to given
ports of the given cell. Can be used multiple times. This is in
addition to the cells specified as mapping targets.
-widthparam <param_name>
Use the specified parameter name to set the port width.
-nameparam <param_name>
Use the specified parameter to set the port name.
-bits
create individual bit-wide buffers even for ports that
are wider. (the default behavior is to create word-wide
buffers using -widthparam to set the word size on the cell.)
Tristate PADS (-toutpad, -tinoutpad) always operate in -bits mode.
\end{lstlisting}
\section{json -- write design in JSON format}
\label{cmd:json}
\begin{lstlisting}[numbers=left,frame=single]
json [options] [selection]
Write a JSON netlist of all selected objects.
-o <filename>
write to the specified file.
-aig
also include AIG models for the different gate types
-compat-int
emit 32-bit or smaller fully-defined parameter values directly
as JSON numbers (for compatibility with old parsers)
See 'help write_json' for a description of the JSON format used.
\end{lstlisting}
\section{log -- print text and log files}
\label{cmd:log}
\begin{lstlisting}[numbers=left,frame=single]
log string
Print the given string to the screen and/or the log file. This is useful for TCL
scripts, because the TCL command "puts" only goes to stdout but not to
logfiles.
-stdout
Print the output to stdout too. This is useful when all Yosys is executed
with a script and the -q (quiet operation) argument to notify the user.
-stderr
Print the output to stderr too.
-nolog
Don't use the internal log() command. Use either -stdout or -stderr,
otherwise no output will be generated at all.
-n
do not append a newline
\end{lstlisting}
\section{logger -- set logger properties}
\label{cmd:logger}
\begin{lstlisting}[numbers=left,frame=single]
logger [options]
This command sets global logger properties, also available using command line
options.
-[no]time
enable/disable display of timestamp in log output.
-[no]stderr
enable/disable logging errors to stderr.
-warn regex
print a warning for all log messages matching the regex.
-nowarn regex
if a warning message matches the regex, it is printed as regular
message instead.
-werror regex
if a warning message matches the regex, it is printed as error
message instead and the tool terminates with a nonzero return code.
-[no]debug
globally enable/disable debug log messages.
-experimental <feature>
do not print warnings for the specified experimental feature
-expect <type> <regex> <expected_count>
expect log, warning or error to appear. matched errors will terminate
with exit code 0.
-expect-no-warnings
gives error in case there is at least one warning that is not expected.
-check-expected
verifies that the patterns previously set up by -expect have actually
been met, then clears the expected log list. If this is not called
manually, the check will happen at yosys exist time instead.
\end{lstlisting}
\section{ls -- list modules or objects in modules}
\label{cmd:ls}
\begin{lstlisting}[numbers=left,frame=single]
ls [selection]
When no active module is selected, this prints a list of modules.
When an active module is selected, this prints a list of objects in the module.
\end{lstlisting}
\section{ltp -- print longest topological path}
\label{cmd:ltp}
\begin{lstlisting}[numbers=left,frame=single]
ltp [options] [selection]
This command prints the longest topological path in the design. (Only considers
paths within a single module, so the design must be flattened.)
-noff
automatically exclude FF cell types
\end{lstlisting}
\section{lut2mux -- convert \$lut to \$\_MUX\_}
\label{cmd:lut2mux}
\begin{lstlisting}[numbers=left,frame=single]
lut2mux [options] [selection]
This pass converts $lut cells to $_MUX_ gates.
\end{lstlisting}
\section{maccmap -- mapping macc cells}
\label{cmd:maccmap}
\begin{lstlisting}[numbers=left,frame=single]
maccmap [-unmap] [selection]
This pass maps $macc cells to yosys $fa and $alu cells. When the -unmap option
is used then the $macc cell is mapped to $add, $sub, etc. cells instead.
\end{lstlisting}
\section{memory -- translate memories to basic cells}
\label{cmd:memory}
\begin{lstlisting}[numbers=left,frame=single]
memory [-nomap] [-nordff] [-nowiden] [-nosat] [-memx] [-bram <bram_rules>] [selection]
This pass calls all the other memory_* passes in a useful order:
opt_mem
opt_mem_priority
opt_mem_feedback
memory_dff (skipped if called with -nordff or -memx)
opt_clean
memory_share [-nowiden] [-nosat]
opt_mem_widen
memory_memx (when called with -memx)
opt_clean
memory_collect
memory_bram -rules <bram_rules> (when called with -bram)
memory_map (skipped if called with -nomap)
This converts memories to word-wide DFFs and address decoders
or multiport memory blocks if called with the -nomap option.
\end{lstlisting}
\section{memory\_bram -- map memories to block rams}
\label{cmd:memory_bram}
\begin{lstlisting}[numbers=left,frame=single]
memory_bram -rules <rule_file> [selection]
This pass converts the multi-port $mem memory cells into block ram instances.
The given rules file describes the available resources and how they should be
used.
The rules file contains configuration options, a set of block ram description
and a sequence of match rules.
The option 'attr_icase' configures how attribute values are matched. The value 0
means case-sensitive, 1 means case-insensitive.
A block ram description looks like this:
bram RAMB1024X32 # name of BRAM cell
init 1 # set to '1' if BRAM can be initialized
abits 10 # number of address bits
dbits 32 # number of data bits
groups 2 # number of port groups
ports 1 1 # number of ports in each group
wrmode 1 0 # set to '1' if this groups is write ports
enable 4 1 # number of enable bits
transp 0 2 # transparent (for read ports)
clocks 1 2 # clock configuration
clkpol 2 2 # clock polarity configuration
endbram
For the option 'transp' the value 0 means non-transparent, 1 means transparent
and a value greater than 1 means configurable. All groups with the same
value greater than 1 share the same configuration bit.
For the option 'clocks' the value 0 means non-clocked, and a value greater
than 0 means clocked. All groups with the same value share the same clock
signal.
For the option 'clkpol' the value 0 means negative edge, 1 means positive edge
and a value greater than 1 means configurable. All groups with the same value
greater than 1 share the same configuration bit.
Using the same bram name in different bram blocks will create different variants
of the bram. Verilog configuration parameters for the bram are created as needed.
It is also possible to create variants by repeating statements in the bram block
and appending '@<label>' to the individual statements.
A match rule looks like this:
match RAMB1024X32
max waste 16384 # only use this bram if <= 16k ram bits are unused
min efficiency 80 # only use this bram if efficiency is at least 80%
endmatch
It is possible to match against the following values with min/max rules:
words ........ number of words in memory in design
abits ........ number of address bits on memory in design
dbits ........ number of data bits on memory in design
wports ....... number of write ports on memory in design
rports ....... number of read ports on memory in design
ports ........ number of ports on memory in design
bits ......... number of bits in memory in design
dups .......... number of duplications for more read ports
awaste ....... number of unused address slots for this match
dwaste ....... number of unused data bits for this match
bwaste ....... number of unused bram bits for this match
waste ........ total number of unused bram bits (bwaste*dups)
efficiency ... total percentage of used and non-duplicated bits
acells ....... number of cells in 'address-direction'
dcells ....... number of cells in 'data-direction'
cells ........ total number of cells (acells*dcells*dups)
A match containing the command 'attribute' followed by a list of space
separated 'name[=string_value]' values requires that the memory contains any
one of the given attribute name and string values (where specified), or name
and integer 1 value (if no string_value given, since Verilog will interpret
'(* attr *)' as '(* attr=1 *)').
A name prefixed with '!' indicates that the attribute must not exist.
The interface for the created bram instances is derived from the bram
description. Use 'techmap' to convert the created bram instances into
instances of the actual bram cells of your target architecture.
A match containing the command 'or_next_if_better' is only used if it
has a higher efficiency than the next match (and the one after that if
the next also has 'or_next_if_better' set, and so forth).
A match containing the command 'make_transp' will add external circuitry
to simulate 'transparent read', if necessary.
A match containing the command 'make_outreg' will add external flip-flops
to implement synchronous read ports, if necessary.
A match containing the command 'shuffle_enable A' will re-organize
the data bits to accommodate the enable pattern of port A.
\end{lstlisting}
\section{memory\_collect -- creating multi-port memory cells}
\label{cmd:memory_collect}
\begin{lstlisting}[numbers=left,frame=single]
memory_collect [selection]
This pass collects memories and memory ports and creates generic multiport
memory cells.
\end{lstlisting}
\section{memory\_dff -- merge input/output DFFs into memory read ports}
\label{cmd:memory_dff}
\begin{lstlisting}[numbers=left,frame=single]
memory_dff [options] [selection]
This pass detects DFFs at memory read ports and merges them into the memory port.
I.e. it consumes an asynchronous memory port and the flip-flops at its
interface and yields a synchronous memory port.
\end{lstlisting}
\section{memory\_map -- translate multiport memories to basic cells}
\label{cmd:memory_map}
\begin{lstlisting}[numbers=left,frame=single]
memory_map [options] [selection]
This pass converts multiport memory cells as generated by the memory_collect
pass to word-wide DFFs and address decoders.
-attr !<name>
do not map memories that have attribute <name> set.
-attr <name>[=<value>]
for memories that have attribute <name> set, only map them if its value
is a string <value> (if specified), or an integer 1 (otherwise). if this
option is specified multiple times, map the memory if the attribute is
to any of the values.
-iattr
for -attr, ignore case of <value>.
\end{lstlisting}
\section{memory\_memx -- emulate vlog sim behavior for mem ports}
\label{cmd:memory_memx}
\begin{lstlisting}[numbers=left,frame=single]
memory_memx [selection]
This pass adds additional circuitry that emulates the Verilog simulation
behavior for out-of-bounds memory reads and writes.
\end{lstlisting}
\section{memory\_narrow -- split up wide memory ports}
\label{cmd:memory_narrow}
\begin{lstlisting}[numbers=left,frame=single]
memory_narrow [options] [selection]
This pass splits up wide memory ports into several narrow ports.
\end{lstlisting}
\section{memory\_nordff -- extract read port FFs from memories}
\label{cmd:memory_nordff}
\begin{lstlisting}[numbers=left,frame=single]
memory_nordff [options] [selection]
This pass extracts FFs from memory read ports. This results in a netlist
similar to what one would get from not calling memory_dff.
\end{lstlisting}
\section{memory\_share -- consolidate memory ports}
\label{cmd:memory_share}
\begin{lstlisting}[numbers=left,frame=single]
memory_share [-nosat] [-nowiden] [selection]
This pass merges share-able memory ports into single memory ports.
The following methods are used to consolidate the number of memory ports:
- When multiple write ports access the same address then this is converted
to a single write port with a more complex data and/or enable logic path.
- When multiple read or write ports access adjacent aligned addresses, they are
merged to a single wide read or write port. This transformation can be
disabled with the "-nowiden" option.
- When multiple write ports are never accessed at the same time (a SAT
solver is used to determine this), then the ports are merged into a single
write port. This transformation can be disabled with the "-nosat" option.
Note that in addition to the algorithms implemented in this pass, the $memrd
and $memwr cells are also subject to generic resource sharing passes (and other
optimizations) such as "share" and "opt_merge".
\end{lstlisting}
\section{memory\_unpack -- unpack multi-port memory cells}
\label{cmd:memory_unpack}
\begin{lstlisting}[numbers=left,frame=single]
memory_unpack [selection]
This pass converts the multi-port $mem memory cells into individual $memrd and
$memwr cells. It is the counterpart to the memory_collect pass.
\end{lstlisting}
\section{miter -- automatically create a miter circuit}
\label{cmd:miter}
\begin{lstlisting}[numbers=left,frame=single]
miter -equiv [options] gold_name gate_name miter_name
Creates a miter circuit for equivalence checking. The gold- and gate- modules
must have the same interfaces. The miter circuit will have all inputs of the
two source modules, prefixed with 'in_'. The miter circuit has a 'trigger'
output that goes high if an output mismatch between the two source modules is
detected.
-ignore_gold_x
a undef (x) bit in the gold module output will match any value in
the gate module output.
-make_outputs
also route the gold- and gate-outputs to 'gold_*' and 'gate_*' outputs
on the miter circuit.
-make_outcmp
also create a cmp_* output for each gold/gate output pair.
-make_assert
also create an 'assert' cell that checks if trigger is always low.
-flatten
call 'flatten -wb; opt_expr -keepdc -undriven;;' on the miter circuit.
miter -assert [options] module [miter_name]
Creates a miter circuit for property checking. All input ports are kept,
output ports are discarded. An additional output 'trigger' is created that
goes high when an assert is violated. Without a miter_name, the existing
module is modified.
-make_outputs
keep module output ports.
-flatten
call 'flatten -wb; opt_expr -keepdc -undriven;;' on the miter circuit.
\end{lstlisting}
\section{mutate -- generate or apply design mutations}
\label{cmd:mutate}
\begin{lstlisting}[numbers=left,frame=single]
mutate -list N [options] [selection]
Create a list of N mutations using an even sampling.
-o filename
Write list to this file instead of console output
-s filename
Write a list of all src tags found in the design to the specified file
-seed N
RNG seed for selecting mutations
-none
Include a "none" mutation in the output
-ctrl name width value
Add -ctrl options to the output. Use 'value' for first mutation, then
simply count up from there.
-mode name
-module name
-cell name
-port name
-portbit int
-ctrlbit int
-wire name
-wirebit int
-src string
Filter list of mutation candidates to those matching
the given parameters.
-cfg option int
Set a configuration option. Options available:
weight_pq_w weight_pq_b weight_pq_c weight_pq_s
weight_pq_mw weight_pq_mb weight_pq_mc weight_pq_ms
weight_cover pick_cover_prcnt
mutate -mode MODE [options]
Apply the given mutation.
-ctrl name width value
Add a control signal with the given name and width. The mutation is
activated if the control signal equals the given value.
-module name
-cell name
-port name
-portbit int
-ctrlbit int
Mutation parameters, as generated by 'mutate -list N'.
-wire name
-wirebit int
-src string
Ignored. (They are generated by -list for documentation purposes.)
\end{lstlisting}
\section{muxcover -- cover trees of MUX cells with wider MUXes}
\label{cmd:muxcover}
\begin{lstlisting}[numbers=left,frame=single]
muxcover [options] [selection]
Cover trees of $_MUX_ cells with $_MUX{4,8,16}_ cells
-mux4[=cost], -mux8[=cost], -mux16[=cost]
Cover $_MUX_ trees using the specified types of MUXes (with optional
integer costs). If none of these options are given, the effect is the
same as if all of them are.
Default costs: $_MUX4_ = 220, $_MUX8_ = 460,
$_MUX16_ = 940
-mux2=cost
Use the specified cost for $_MUX_ cells when making covering decisions.
Default cost: $_MUX_ = 100
-dmux=cost
Use the specified cost for $_MUX_ cells used in decoders.
Default cost: 90
-nodecode
Do not insert decoder logic. This reduces the number of possible
substitutions, but guarantees that the resulting circuit is not
less efficient than the original circuit.
-nopartial
Do not consider mappings that use $_MUX<N>_ to select from less
than <N> different signals.
\end{lstlisting}
\section{muxpack -- \$mux/\$pmux cascades to \$pmux}
\label{cmd:muxpack}
\begin{lstlisting}[numbers=left,frame=single]
muxpack [selection]
This pass converts cascaded chains of $pmux cells (e.g. those create from case
constructs) and $mux cells (e.g. those created by if-else constructs) into
$pmux cells.
This optimisation is conservative --- it will only pack $mux or $pmux cells
whose select lines are driven by '$eq' cells with other such cells if it can be
certain that their select inputs are mutually exclusive.
\end{lstlisting}
\section{nlutmap -- map to LUTs of different sizes}
\label{cmd:nlutmap}
\begin{lstlisting}[numbers=left,frame=single]
nlutmap [options] [selection]
This pass uses successive calls to 'abc' to map to an architecture. That
provides a small number of differently sized LUTs.
-luts N_1,N_2,N_3,...
The number of LUTs with 1, 2, 3, ... inputs that are
available in the target architecture.
-assert
Create an error if not all logic can be mapped
Excess logic that does not fit into the specified LUTs is mapped back
to generic logic gates ($_AND_, etc.).
\end{lstlisting}
\section{onehot -- optimize \$eq cells for onehot signals}
\label{cmd:onehot}
\begin{lstlisting}[numbers=left,frame=single]
onehot [options] [selection]
This pass optimizes $eq cells that compare one-hot signals against constants
-v, -vv
verbose output
\end{lstlisting}
\section{opt -- perform simple optimizations}
\label{cmd:opt}
\begin{lstlisting}[numbers=left,frame=single]
opt [options] [selection]
This pass calls all the other opt_* passes in a useful order. This performs
a series of trivial optimizations and cleanups. This pass executes the other
passes in the following order:
opt_expr [-mux_undef] [-mux_bool] [-undriven] [-noclkinv] [-fine] [-full] [-keepdc]
opt_merge [-share_all] -nomux
do
opt_muxtree
opt_reduce [-fine] [-full]
opt_merge [-share_all]
opt_share (-full only)
opt_dff [-nodffe] [-nosdff] [-keepdc] [-sat] (except when called with -noff)
opt_clean [-purge]
opt_expr [-mux_undef] [-mux_bool] [-undriven] [-noclkinv] [-fine] [-full] [-keepdc]
while <changed design>
When called with -fast the following script is used instead:
do
opt_expr [-mux_undef] [-mux_bool] [-undriven] [-noclkinv] [-fine] [-full] [-keepdc]
opt_merge [-share_all]
opt_dff [-nodffe] [-nosdff] [-keepdc] [-sat] (except when called with -noff)
opt_clean [-purge]
while <changed design in opt_dff>
Note: Options in square brackets (such as [-keepdc]) are passed through to
the opt_* commands when given to 'opt'.
\end{lstlisting}
\section{opt\_clean -- remove unused cells and wires}
\label{cmd:opt_clean}
\begin{lstlisting}[numbers=left,frame=single]
opt_clean [options] [selection]
This pass identifies wires and cells that are unused and removes them. Other
passes often remove cells but leave the wires in the design or reconnect the
wires but leave the old cells in the design. This pass can be used to clean up
after the passes that do the actual work.
This pass only operates on completely selected modules without processes.
-purge
also remove internal nets if they have a public name
\end{lstlisting}
\section{opt\_demorgan -- Optimize reductions with DeMorgan equivalents}
\label{cmd:opt_demorgan}
\begin{lstlisting}[numbers=left,frame=single]
opt_demorgan [selection]
This pass pushes inverters through $reduce_* cells if this will reduce the
overall gate count of the circuit
\end{lstlisting}
\section{opt\_dff -- perform DFF optimizations}
\label{cmd:opt_dff}
\begin{lstlisting}[numbers=left,frame=single]
opt_dff [-nodffe] [-nosdff] [-keepdc] [-sat] [selection]
This pass converts flip-flops to a more suitable type by merging clock enables
and synchronous reset multiplexers, removing unused control inputs, or potentially
removes the flip-flop altogether, converting it to a constant driver.
-nodffe
disables dff -> dffe conversion, and other transforms recognizing clock enable
-nosdff
disables dff -> sdff conversion, and other transforms recognizing sync resets
-simple-dffe
only enables clock enable recognition transform for obvious cases
-sat
additionally invoke SAT solver to detect and remove flip-flops (with
non-constant inputs) that can also be replaced with a constant driver
-keepdc
some optimizations change the behavior of the circuit with respect to
don't-care bits. for example in 'a+0' a single x-bit in 'a' will cause
all result bits to be set to x. this behavior changes when 'a+0' is
replaced by 'a'. the -keepdc option disables all such optimizations.
\end{lstlisting}
\section{opt\_expr -- perform const folding and simple expression rewriting}
\label{cmd:opt_expr}
\begin{lstlisting}[numbers=left,frame=single]
opt_expr [options] [selection]
This pass performs const folding on internal cell types with constant inputs.
It also performs some simple expression rewriting.
-mux_undef
remove 'undef' inputs from $mux, $pmux and $_MUX_ cells
-mux_bool
replace $mux cells with inverters or buffers when possible
-undriven
replace undriven nets with undef (x) constants
-noclkinv
do not optimize clock inverters by changing FF types
-fine
perform fine-grain optimizations
-full
alias for -mux_undef -mux_bool -undriven -fine
-keepdc
some optimizations change the behavior of the circuit with respect to
don't-care bits. for example in 'a+0' a single x-bit in 'a' will cause
all result bits to be set to x. this behavior changes when 'a+0' is
replaced by 'a'. the -keepdc option disables all such optimizations.
\end{lstlisting}
\section{opt\_lut -- optimize LUT cells}
\label{cmd:opt_lut}
\begin{lstlisting}[numbers=left,frame=single]
opt_lut [options] [selection]
This pass combines cascaded $lut cells with unused inputs.
-dlogic <type>:<cell-port>=<LUT-input>[:<cell-port>=<LUT-input>...]
preserve connections to dedicated logic cell <type> that has ports
<cell-port> connected to LUT inputs <LUT-input>. this includes
the case where both LUT and dedicated logic input are connected to
the same constant.
-limit N
only perform the first N combines, then stop. useful for debugging.
\end{lstlisting}
\section{opt\_lut\_ins -- discard unused LUT inputs}
\label{cmd:opt_lut_ins}
\begin{lstlisting}[numbers=left,frame=single]
opt_lut_ins [options] [selection]
This pass removes unused inputs from LUT cells (that is, inputs that can not
influence the output signal given this LUT's value). While such LUTs cannot
be directly emitted by ABC, they can be a result of various post-ABC
transformations, such as mapping wide LUTs (not all sub-LUTs will use the
full set of inputs) or optimizations such as xilinx_dffopt.
-tech <technology>
Instead of generic $lut cells, operate on LUT cells specific
to the given technology. Valid values are: xilinx, ecp5, gowin.
\end{lstlisting}
\section{opt\_mem -- optimize memories}
\label{cmd:opt_mem}
\begin{lstlisting}[numbers=left,frame=single]
opt_mem [options] [selection]
This pass performs various optimizations on memories in the design.
\end{lstlisting}
\section{opt\_mem\_feedback -- convert memory read-to-write port feedback paths to write enables}
\label{cmd:opt_mem_feedback}
\begin{lstlisting}[numbers=left,frame=single]
opt_mem_feedback [selection]
This pass detects cases where an asynchronous read port is only connected via
a mux tree to a write port with the same address. When such a connection is
found, it is replaced with a new condition on an enable signal, allowing
for removal of the read port.
\end{lstlisting}
\section{opt\_mem\_priority -- remove priority relations between write ports that can never collide}
\label{cmd:opt_mem_priority}
\begin{lstlisting}[numbers=left,frame=single]
opt_mem_priority [selection]
This pass detects cases where one memory write port has priority over another
even though they can never collide with each other -- ie. there can never be
a situation where a given memory bit is written by both ports at the same
time, for example because of always-different addresses, or mutually exclusive
enable signals. In such cases, the priority relation is removed.
\end{lstlisting}
\section{opt\_mem\_widen -- optimize memories where all ports are wide}
\label{cmd:opt_mem_widen}
\begin{lstlisting}[numbers=left,frame=single]
opt_mem_widen [options] [selection]
This pass looks for memories where all ports are wide and adjusts the base
memory width up until that stops being the case.
\end{lstlisting}
\section{opt\_merge -- consolidate identical cells}
\label{cmd:opt_merge}
\begin{lstlisting}[numbers=left,frame=single]
opt_merge [options] [selection]
This pass identifies cells with identical type and input signals. Such cells
are then merged to one cell.
-nomux
Do not merge MUX cells.
-share_all
Operate on all cell types, not just built-in types.
\end{lstlisting}
\section{opt\_muxtree -- eliminate dead trees in multiplexer trees}
\label{cmd:opt_muxtree}
\begin{lstlisting}[numbers=left,frame=single]
opt_muxtree [selection]
This pass analyzes the control signals for the multiplexer trees in the design
and identifies inputs that can never be active. It then removes this dead
branches from the multiplexer trees.
This pass only operates on completely selected modules without processes.
\end{lstlisting}
\section{opt\_reduce -- simplify large MUXes and AND/OR gates}
\label{cmd:opt_reduce}
\begin{lstlisting}[numbers=left,frame=single]
opt_reduce [options] [selection]
This pass performs two interlinked optimizations:
1. it consolidates trees of large AND gates or OR gates and eliminates
duplicated inputs.
2. it identifies duplicated inputs to MUXes and replaces them with a single
input with the original control signals OR'ed together.
-fine
perform fine-grain optimizations
-full
alias for -fine
\end{lstlisting}
\section{opt\_share -- merge mutually exclusive cells of the same type that share an input signal}
\label{cmd:opt_share}
\begin{lstlisting}[numbers=left,frame=single]
opt_share [selection]
This pass identifies mutually exclusive cells of the same type that:
(a) share an input signal,
(b) drive the same $mux, $_MUX_, or $pmux multiplexing cell,
allowing the cell to be merged and the multiplexer to be moved from
multiplexing its output to multiplexing the non-shared input signals.
\end{lstlisting}
\section{paramap -- renaming cell parameters}
\label{cmd:paramap}
\begin{lstlisting}[numbers=left,frame=single]
paramap [options] [selection]
This command renames cell parameters and/or maps key/value pairs to
other key/value pairs.
-tocase <name>
Match attribute names case-insensitively and set it to the specified
name.
-rename <old_name> <new_name>
Rename attributes as specified
-map <old_name>=<old_value> <new_name>=<new_value>
Map key/value pairs as indicated.
-imap <old_name>=<old_value> <new_name>=<new_value>
Like -map, but use case-insensitive match for <old_value> when
it is a string value.
-remove <name>=<value>
Remove attributes matching this pattern.
For example, mapping Diamond-style ECP5 "init" attributes to Yosys-style:
paramap -tocase INIT t:LUT4
\end{lstlisting}
\section{peepopt -- collection of peephole optimizers}
\label{cmd:peepopt}
\begin{lstlisting}[numbers=left,frame=single]
peepopt [options] [selection]
This pass applies a collection of peephole optimizers to the current design.
\end{lstlisting}
\section{plugin -- load and list loaded plugins}
\label{cmd:plugin}
\begin{lstlisting}[numbers=left,frame=single]
plugin [options]
Load and list loaded plugins.
-i <plugin_filename>
Load (install) the specified plugin.
-a <alias_name>
Register the specified alias name for the loaded plugin
-l
List loaded plugins
\end{lstlisting}
\section{pmux2shiftx -- transform \$pmux cells to \$shiftx cells}
\label{cmd:pmux2shiftx}
\begin{lstlisting}[numbers=left,frame=single]
pmux2shiftx [options] [selection]
This pass transforms $pmux cells to $shiftx cells.
-v, -vv
verbose output
-min_density <percentage>
specifies the minimum density for the shifter
default: 50
-min_choices <int>
specified the minimum number of choices for a control signal
default: 3
-onehot ignore|pmux|shiftx
select strategy for one-hot encoded control signals
default: pmux
-norange
disable $sub inference for "range decoders"
\end{lstlisting}
\section{pmuxtree -- transform \$pmux cells to trees of \$mux cells}
\label{cmd:pmuxtree}
\begin{lstlisting}[numbers=left,frame=single]
pmuxtree [selection]
This pass transforms $pmux cells to trees of $mux cells.
\end{lstlisting}
\section{portlist -- list (top-level) ports}
\label{cmd:portlist}
\begin{lstlisting}[numbers=left,frame=single]
portlist [options] [selection]
This command lists all module ports found in the selected modules.
If no selection is provided then it lists the ports on the top module.
-m
print verilog blackbox module definitions instead of port lists
\end{lstlisting}
\section{prep -- generic synthesis script}
\label{cmd:prep}
\begin{lstlisting}[numbers=left,frame=single]
prep [options]
This command runs a conservative RTL synthesis. A typical application for this
is the preparation stage of a verification flow. This command does not operate
on partly selected designs.
-top <module>
use the specified module as top module (default='top')
-auto-top
automatically determine the top of the design hierarchy
-flatten
flatten the design before synthesis. this will pass '-auto-top' to
'hierarchy' if no top module is specified.
-ifx
passed to 'proc'. uses verilog simulation behavior for verilog if/case
undef handling. this also prevents 'wreduce' from being run.
-memx
simulate verilog simulation behavior for out-of-bounds memory accesses
using the 'memory_memx' pass.
-nomem
do not run any of the memory_* passes
-rdff
call 'memory_dff'. This enables merging of FFs into
memory read ports.
-nokeepdc
do not call opt_* with -keepdc
-run <from_label>[:<to_label>]
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
The following commands are executed by this synthesis command:
begin:
hierarchy -check [-top <top> | -auto-top]
coarse:
proc [-ifx]
flatten (if -flatten)
opt_expr -keepdc
opt_clean
check
opt -noff -keepdc
wreduce -keepdc [-memx]
memory_dff (if -rdff)
memory_memx (if -memx)
opt_clean
memory_collect
opt -noff -keepdc -fast
check:
stat
check
\end{lstlisting}
\section{printattrs -- print attributes of selected objects}
\label{cmd:printattrs}
\begin{lstlisting}[numbers=left,frame=single]
printattrs [selection]
Print all attributes of the selected objects.
\end{lstlisting}
\section{proc -- translate processes to netlists}
\label{cmd:proc}
\begin{lstlisting}[numbers=left,frame=single]
proc [options] [selection]
This pass calls all the other proc_* passes in the most common order.
proc_clean
proc_rmdead
proc_prune
proc_init
proc_arst
proc_mux
proc_dlatch
proc_dff
proc_memwr
proc_clean
opt_expr -keepdc
This replaces the processes in the design with multiplexers,
flip-flops and latches.
The following options are supported:
-nomux
Will omit the proc_mux pass.
-global_arst [!]<netname>
This option is passed through to proc_arst.
-ifx
This option is passed through to proc_mux. proc_rmdead is not
executed in -ifx mode.
-noopt
Will omit the opt_expr pass.
\end{lstlisting}
\section{proc\_arst -- detect asynchronous resets}
\label{cmd:proc_arst}
\begin{lstlisting}[numbers=left,frame=single]
proc_arst [-global_arst [!]<netname>] [selection]
This pass identifies asynchronous resets in the processes and converts them
to a different internal representation that is suitable for generating
flip-flop cells with asynchronous resets.
-global_arst [!]<netname>
In modules that have a net with the given name, use this net as async
reset for registers that have been assign initial values in their
declaration ('reg foobar = constant_value;'). Use the '!' modifier for
active low reset signals. Note: the frontend stores the default value
in the 'init' attribute on the net.
\end{lstlisting}
\section{proc\_clean -- remove empty parts of processes}
\label{cmd:proc_clean}
\begin{lstlisting}[numbers=left,frame=single]
proc_clean [options] [selection]
-quiet
do not print any messages.
This pass removes empty parts of processes and ultimately removes a process
if it contains only empty structures.
\end{lstlisting}
\section{proc\_dff -- extract flip-flops from processes}
\label{cmd:proc_dff}
\begin{lstlisting}[numbers=left,frame=single]
proc_dff [selection]
This pass identifies flip-flops in the processes and converts them to
d-type flip-flop cells.
\end{lstlisting}
\section{proc\_dlatch -- extract latches from processes}
\label{cmd:proc_dlatch}
\begin{lstlisting}[numbers=left,frame=single]
proc_dlatch [selection]
This pass identifies latches in the processes and converts them to
d-type latches.
\end{lstlisting}
\section{proc\_init -- convert initial block to init attributes}
\label{cmd:proc_init}
\begin{lstlisting}[numbers=left,frame=single]
proc_init [selection]
This pass extracts the 'init' actions from processes (generated from Verilog
'initial' blocks) and sets the initial value to the 'init' attribute on the
respective wire.
\end{lstlisting}
\section{proc\_memwr -- extract memory writes from processes}
\label{cmd:proc_memwr}
\begin{lstlisting}[numbers=left,frame=single]
proc_memwr [selection]
This pass converts memory writes in processes into $memwr cells.
\end{lstlisting}
\section{proc\_mux -- convert decision trees to multiplexers}
\label{cmd:proc_mux}
\begin{lstlisting}[numbers=left,frame=single]
proc_mux [options] [selection]
This pass converts the decision trees in processes (originating from if-else
and case statements) to trees of multiplexer cells.
-ifx
Use Verilog simulation behavior with respect to undef values in
'case' expressions and 'if' conditions.
\end{lstlisting}
\section{proc\_prune -- remove redundant assignments}
\label{cmd:proc_prune}
\begin{lstlisting}[numbers=left,frame=single]
proc_prune [selection]
This pass identifies assignments in processes that are always overwritten by
a later assignment to the same signal and removes them.
\end{lstlisting}
\section{proc\_rmdead -- eliminate dead trees in decision trees}
\label{cmd:proc_rmdead}
\begin{lstlisting}[numbers=left,frame=single]
proc_rmdead [selection]
This pass identifies unreachable branches in decision trees and removes them.
\end{lstlisting}
\section{qbfsat -- solve a 2QBF-SAT problem in the circuit}
\label{cmd:qbfsat}
\begin{lstlisting}[numbers=left,frame=single]
qbfsat [options] [selection]
This command solves an "exists-forall" 2QBF-SAT problem defined over the currently
selected module. Existentially-quantified variables are declared by assigning a wire
"$anyconst". Universally-quantified variables may be explicitly declared by assigning
a wire "$allconst", but module inputs will be treated as universally-quantified
variables by default.
-nocleanup
Do not delete temporary files and directories. Useful for debugging.
-dump-final-smt2 <file>
Pass the --dump-smt2 option to yosys-smtbmc.
-assume-outputs
Add an "$assume" cell for the conjunction of all one-bit module output wires.
-assume-negative-polarity
When adding $assume cells for one-bit module output wires, assume they are
negative polarity signals and should always be low, for example like the
miters created with the `miter` command.
-nooptimize
Ignore "\minimize" and "\maximize" attributes, do not emit "(maximize)" or
"(minimize)" in the SMT-LIBv2, and generally make no attempt to optimize anything.
-nobisection
If a wire is marked with the "\minimize" or "\maximize" attribute, do not
attempt to optimize that value with the default iterated solving and threshold
bisection approach. Instead, have yosys-smtbmc emit a "(minimize)" or "(maximize)"
command in the SMT-LIBv2 output and hope that the solver supports optimizing
quantified bitvector problems.
-solver <solver>
Use a particular solver. Choose one of: "z3", "yices", and "cvc4".
(default: yices)
-solver-option <name> <value>
Set the specified solver option in the SMT-LIBv2 problem file.
-timeout <value>
Set the per-iteration timeout in seconds.
(default: no timeout)
-O0, -O1, -O2
Control the use of ABC to simplify the QBF-SAT problem before solving.
-sat
Generate an error if the solver does not return "sat".
-unsat
Generate an error if the solver does not return "unsat".
-show-smtbmc
Print the output from yosys-smtbmc.
-specialize
If the problem is satisfiable, replace each "$anyconst" cell with its
corresponding constant value from the model produced by the solver.
-specialize-from-file <solution file>
Do not run the solver, but instead only attempt to replace each "$anyconst"
cell in the current module with a constant value provided by the specified file.
-write-solution <solution file>
If the problem is satisfiable, write the corresponding constant value for each
"$anyconst" cell from the model produced by the solver to the specified file.
\end{lstlisting}
\section{qwp -- quadratic wirelength placer}
\label{cmd:qwp}
\begin{lstlisting}[numbers=left,frame=single]
qwp [options] [selection]
This command runs quadratic wirelength placement on the selected modules and
annotates the cells in the design with 'qwp_position' attributes.
-ltr
Add left-to-right constraints: constrain all inputs on the left border
outputs to the right border.
-alpha
Add constraints for inputs/outputs to be placed in alphanumerical
order along the y-axis (top-to-bottom).
-grid N
Number of grid divisions in x- and y-direction. (default=16)
-dump <html_file_name>
Dump a protocol of the placement algorithm to the html file.
-v
Verbose solver output for profiling or debugging
Note: This implementation of a quadratic wirelength placer uses exact
dense matrix operations. It is only a toy-placer for small circuits.
\end{lstlisting}
\section{read -- load HDL designs}
\label{cmd:read}
\begin{lstlisting}[numbers=left,frame=single]
read {-vlog95|-vlog2k|-sv2005|-sv2009|-sv2012|-sv|-formal} <verilog-file>..
Load the specified Verilog/SystemVerilog files. (Full SystemVerilog support
is only available via Verific.)
Additional -D<macro>[=<value>] options may be added after the option indicating
the language version (and before file names) to set additional verilog defines.
read {-vhdl87|-vhdl93|-vhdl2k|-vhdl2008|-vhdl} <vhdl-file>..
Load the specified VHDL files. (Requires Verific.)
read {-f|-F} <command-file>
Load and execute the specified command file. (Requires Verific.)
Check verific command for more information about supported commands in file.
read -define <macro>[=<value>]..
Set global Verilog/SystemVerilog defines.
read -undef <macro>..
Unset global Verilog/SystemVerilog defines.
read -incdir <directory>
Add directory to global Verilog/SystemVerilog include directories.
read -verific
read -noverific
Subsequent calls to 'read' will either use or not use Verific. Calling 'read'
with -verific will result in an error on Yosys binaries that are built without
Verific support. The default is to use Verific if it is available.
\end{lstlisting}
\section{read\_aiger -- read AIGER file}
\label{cmd:read_aiger}
\begin{lstlisting}[numbers=left,frame=single]
read_aiger [options] [filename]
Load module from an AIGER file into the current design.
-module_name <module_name>
name of module to be created (default: <filename>)
-clk_name <wire_name>
if specified, AIGER latches to be transformed into $_DFF_P_ cells
clocked by wire of this name. otherwise, $_FF_ cells will be used
-map <filename>
read file with port and latch symbols
-wideports
merge ports that match the pattern 'name[int]' into a single
multi-bit port 'name'
-xaiger
read XAIGER extensions
\end{lstlisting}
\section{read\_blif -- read BLIF file}
\label{cmd:read_blif}
\begin{lstlisting}[numbers=left,frame=single]
read_blif [options] [filename]
Load modules from a BLIF file into the current design.
-sop
Create $sop cells instead of $lut cells
-wideports
Merge ports that match the pattern 'name[int]' into a single
multi-bit port 'name'.
\end{lstlisting}
\section{read\_ilang -- (deprecated) alias of read\_rtlil}
\label{cmd:read_ilang}
\begin{lstlisting}[numbers=left,frame=single]
See `help read_rtlil`.
\end{lstlisting}
\section{read\_json -- read JSON file}
\label{cmd:read_json}
\begin{lstlisting}[numbers=left,frame=single]
read_json [filename]
Load modules from a JSON file into the current design See "help write_json"
for a description of the file format.
\end{lstlisting}
\section{read\_liberty -- read cells from liberty file}
\label{cmd:read_liberty}
\begin{lstlisting}[numbers=left,frame=single]
read_liberty [filename]
Read cells from liberty file as modules into current design.
-lib
only create empty blackbox modules
-nooverwrite
ignore re-definitions of modules. (the default behavior is to
create an error message if the existing module is not a blackbox
module, and overwrite the existing module if it is a blackbox module.)
-overwrite
overwrite existing modules with the same name
-ignore_miss_func
ignore cells with missing function specification of outputs
-ignore_miss_dir
ignore cells with a missing or invalid direction
specification on a pin
-ignore_miss_data_latch
ignore latches with missing data and/or enable pins
-setattr <attribute_name>
set the specified attribute (to the value 1) on all loaded modules
\end{lstlisting}
\section{read\_rtlil -- read modules from RTLIL file}
\label{cmd:read_rtlil}
\begin{lstlisting}[numbers=left,frame=single]
read_rtlil [filename]
Load modules from an RTLIL file to the current design. (RTLIL is a text
representation of a design in yosys's internal format.)
-nooverwrite
ignore re-definitions of modules. (the default behavior is to
create an error message if the existing module is not a blackbox
module, and overwrite the existing module if it is a blackbox module.)
-overwrite
overwrite existing modules with the same name
-lib
only create empty blackbox modules
\end{lstlisting}
\section{read\_verilog -- read modules from Verilog file}
\label{cmd:read_verilog}
\begin{lstlisting}[numbers=left,frame=single]
read_verilog [options] [filename]
Load modules from a Verilog file to the current design. A large subset of
Verilog-2005 is supported.
-sv
enable support for SystemVerilog features. (only a small subset
of SystemVerilog is supported)
-formal
enable support for SystemVerilog assertions and some Yosys extensions
replace the implicit -D SYNTHESIS with -D FORMAL
-nosynthesis
don't add implicit -D SYNTHESIS
-noassert
ignore assert() statements
-noassume
ignore assume() statements
-norestrict
ignore restrict() statements
-assume-asserts
treat all assert() statements like assume() statements
-assert-assumes
treat all assume() statements like assert() statements
-debug
alias for -dump_ast1 -dump_ast2 -dump_vlog1 -dump_vlog2 -yydebug
-dump_ast1
dump abstract syntax tree (before simplification)
-dump_ast2
dump abstract syntax tree (after simplification)
-no_dump_ptr
do not include hex memory addresses in dump (easier to diff dumps)
-dump_vlog1
dump ast as Verilog code (before simplification)
-dump_vlog2
dump ast as Verilog code (after simplification)
-dump_rtlil
dump generated RTLIL netlist
-yydebug
enable parser debug output
-nolatches
usually latches are synthesized into logic loops
this option prohibits this and sets the output to 'x'
in what would be the latches hold condition
this behavior can also be achieved by setting the
'nolatches' attribute on the respective module or
always block.
-nomem2reg
under certain conditions memories are converted to registers
early during simplification to ensure correct handling of
complex corner cases. this option disables this behavior.
this can also be achieved by setting the 'nomem2reg'
attribute on the respective module or register.
This is potentially dangerous. Usually the front-end has good
reasons for converting an array to a list of registers.
Prohibiting this step will likely result in incorrect synthesis
results.
-mem2reg
always convert memories to registers. this can also be
achieved by setting the 'mem2reg' attribute on the respective
module or register.
-nomeminit
do not infer $meminit cells and instead convert initialized
memories to registers directly in the front-end.
-ppdump
dump Verilog code after pre-processor
-nopp
do not run the pre-processor
-nodpi
disable DPI-C support
-noblackbox
do not automatically add a (* blackbox *) attribute to an
empty module.
-lib
only create empty blackbox modules. This implies -DBLACKBOX.
modules with the (* whitebox *) attribute will be preserved.
(* lib_whitebox *) will be treated like (* whitebox *).
-nowb
delete (* whitebox *) and (* lib_whitebox *) attributes from
all modules.
-specify
parse and import specify blocks
-noopt
don't perform basic optimizations (such as const folding) in the
high-level front-end.
-icells
interpret cell types starting with '$' as internal cell types
-pwires
add a wire for each module parameter
-nooverwrite
ignore re-definitions of modules. (the default behavior is to
create an error message if the existing module is not a black box
module, and overwrite the existing module otherwise.)
-overwrite
overwrite existing modules with the same name
-defer
only read the abstract syntax tree and defer actual compilation
to a later 'hierarchy' command. Useful in cases where the default
parameters of modules yield invalid or not synthesizable code.
-noautowire
make the default of `default_nettype be "none" instead of "wire".
-setattr <attribute_name>
set the specified attribute (to the value 1) on all loaded modules
-Dname[=definition]
define the preprocessor symbol 'name' and set its optional value
'definition'
-Idir
add 'dir' to the directories which are used when searching include
files
The command 'verilog_defaults' can be used to register default options for
subsequent calls to 'read_verilog'.
Note that the Verilog frontend does a pretty good job of processing valid
verilog input, but has not very good error reporting. It generally is
recommended to use a simulator (for example Icarus Verilog) for checking
the syntax of the code, rather than to rely on read_verilog for that.
Depending on if read_verilog is run in -formal mode, either the macro
SYNTHESIS or FORMAL is defined automatically, unless -nosynthesis is used.
In addition, read_verilog always defines the macro YOSYS.
See the Yosys README file for a list of non-standard Verilog features
supported by the Yosys Verilog front-end.
\end{lstlisting}
\section{rename -- rename object in the design}
\label{cmd:rename}
\begin{lstlisting}[numbers=left,frame=single]
rename old_name new_name
Rename the specified object. Note that selection patterns are not supported
by this command.
rename -output old_name new_name
Like above, but also make the wire an output. This will fail if the object is
not a wire.
rename -src [selection]
Assign names auto-generated from the src attribute to all selected wires and
cells with private names.
rename -wire [selection]
Assign auto-generated names based on the wires they drive to all selected
cells with private names. Ignores cells driving privatly named wires.
rename -enumerate [-pattern <pattern>] [selection]
Assign short auto-generated names to all selected wires and cells with private
names. The -pattern option can be used to set the pattern for the new names.
The character % in the pattern is replaced with a integer number. The default
pattern is '_%_'.
rename -hide [selection]
Assign private names (the ones with $-prefix) to all selected wires and cells
with public names. This ignores all selected ports.
rename -top new_name
Rename top module.
\end{lstlisting}
\section{rmports -- remove module ports with no connections}
\label{cmd:rmports}
\begin{lstlisting}[numbers=left,frame=single]
rmports [selection]
This pass identifies ports in the selected modules which are not used or
driven and removes them.
\end{lstlisting}
\section{sat -- solve a SAT problem in the circuit}
\label{cmd:sat}
\begin{lstlisting}[numbers=left,frame=single]
sat [options] [selection]
This command solves a SAT problem defined over the currently selected circuit
and additional constraints passed as parameters.
-all
show all solutions to the problem (this can grow exponentially, use
-max <N> instead to get <N> solutions)
-max <N>
like -all, but limit number of solutions to <N>
-enable_undef
enable modeling of undef value (aka 'x-bits')
this option is implied by -set-def, -set-undef et. cetera
-max_undef
maximize the number of undef bits in solutions, giving a better
picture of which input bits are actually vital to the solution.
-set <signal> <value>
set the specified signal to the specified value.
-set-def <signal>
add a constraint that all bits of the given signal must be defined
-set-any-undef <signal>
add a constraint that at least one bit of the given signal is undefined
-set-all-undef <signal>
add a constraint that all bits of the given signal are undefined
-set-def-inputs
add -set-def constraints for all module inputs
-show <signal>
show the model for the specified signal. if no -show option is
passed then a set of signals to be shown is automatically selected.
-show-inputs, -show-outputs, -show-ports
add all module (input/output) ports to the list of shown signals
-show-regs, -show-public, -show-all
show all registers, show signals with 'public' names, show all signals
-ignore_div_by_zero
ignore all solutions that involve a division by zero
-ignore_unknown_cells
ignore all cells that can not be matched to a SAT model
The following options can be used to set up a sequential problem:
-seq <N>
set up a sequential problem with <N> time steps. The steps will
be numbered from 1 to N.
note: for large <N> it can be significantly faster to use
-tempinduct-baseonly -maxsteps <N> instead of -seq <N>.
-set-at <N> <signal> <value>
-unset-at <N> <signal>
set or unset the specified signal to the specified value in the
given timestep. this has priority over a -set for the same signal.
-set-assumes
set all assumptions provided via $assume cells
-set-def-at <N> <signal>
-set-any-undef-at <N> <signal>
-set-all-undef-at <N> <signal>
add undef constraints in the given timestep.
-set-init <signal> <value>
set the initial value for the register driving the signal to the value
-set-init-undef
set all initial states (not set using -set-init) to undef
-set-init-def
do not force a value for the initial state but do not allow undef
-set-init-zero
set all initial states (not set using -set-init) to zero
-dump_vcd <vcd-file-name>
dump SAT model (counter example in proof) to VCD file
-dump_json <json-file-name>
dump SAT model (counter example in proof) to a WaveJSON file.
-dump_cnf <cnf-file-name>
dump CNF of SAT problem (in DIMACS format). in temporal induction
proofs this is the CNF of the first induction step.
The following additional options can be used to set up a proof. If also -seq
is passed, a temporal induction proof is performed.
-tempinduct
Perform a temporal induction proof. In a temporal induction proof it is
proven that the condition holds forever after the number of time steps
specified using -seq.
-tempinduct-def
Perform a temporal induction proof. Assume an initial state with all
registers set to defined values for the induction step.
-tempinduct-baseonly
Run only the basecase half of temporal induction (requires -maxsteps)
-tempinduct-inductonly
Run only the induction half of temporal induction
-tempinduct-skip <N>
Skip the first <N> steps of the induction proof.
note: this will assume that the base case holds for <N> steps.
this must be proven independently with "-tempinduct-baseonly
-maxsteps <N>". Use -initsteps if you just want to set a
minimal induction length.
-prove <signal> <value>
Attempt to proof that <signal> is always <value>.
-prove-x <signal> <value>
Like -prove, but an undef (x) bit in the lhs matches any value on
the right hand side. Useful for equivalence checking.
-prove-asserts
Prove that all asserts in the design hold.
-prove-skip <N>
Do not enforce the prove-condition for the first <N> time steps.
-maxsteps <N>
Set a maximum length for the induction.
-initsteps <N>
Set initial length for the induction.
This will speed up the search of the right induction length
for deep induction proofs.
-stepsize <N>
Increase the size of the induction proof in steps of <N>.
This will speed up the search of the right induction length
for deep induction proofs.
-timeout <N>
Maximum number of seconds a single SAT instance may take.
-verify
Return an error and stop the synthesis script if the proof fails.
-verify-no-timeout
Like -verify but do not return an error for timeouts.
-falsify
Return an error and stop the synthesis script if the proof succeeds.
-falsify-no-timeout
Like -falsify but do not return an error for timeouts.
\end{lstlisting}
\section{scatter -- add additional intermediate nets}
\label{cmd:scatter}
\begin{lstlisting}[numbers=left,frame=single]
scatter [selection]
This command adds additional intermediate nets on all cell ports. This is used
for testing the correct use of the SigMap helper in passes. If you don't know
what this means: don't worry -- you only need this pass when testing your own
extensions to Yosys.
Use the opt_clean command to get rid of the additional nets.
\end{lstlisting}
\section{scc -- detect strongly connected components (logic loops)}
\label{cmd:scc}
\begin{lstlisting}[numbers=left,frame=single]
scc [options] [selection]
This command identifies strongly connected components (aka logic loops) in the
design.
-expect <num>
expect to find exactly <num> SCCs. A different number of SCCs will
produce an error.
-max_depth <num>
limit to loops not longer than the specified number of cells. This
can e.g. be useful in identifying small local loops in a module that
implements one large SCC.
-nofeedback
do not count cells that have their output fed back into one of their
inputs as single-cell scc.
-all_cell_types
Usually this command only considers internal non-memory cells. With
this option set, all cells are considered. For unknown cells all ports
are assumed to be bidirectional 'inout' ports.
-set_attr <name> <value>
set the specified attribute on all cells that are part of a logic
loop. the special token {} in the value is replaced with a unique
identifier for the logic loop.
-select
replace the current selection with a selection of all cells and wires
that are part of a found logic loop
-specify
examine specify rules to detect logic loops in whitebox/blackbox cells
\end{lstlisting}
\section{scratchpad -- get/set values in the scratchpad}
\label{cmd:scratchpad}
\begin{lstlisting}[numbers=left,frame=single]
scratchpad [options]
This pass allows to read and modify values from the scratchpad of the current
design. Options:
-get <identifier>
print the value saved in the scratchpad under the given identifier.
-set <identifier> <value>
save the given value in the scratchpad under the given identifier.
-unset <identifier>
remove the entry for the given identifier from the scratchpad.
-copy <identifier_from> <identifier_to>
copy the value of the first identifier to the second identifier.
-assert <identifier> <value>
assert that the entry for the given identifier is set to the given value.
-assert-set <identifier>
assert that the entry for the given identifier exists.
-assert-unset <identifier>
assert that the entry for the given identifier does not exist.
The identifier may not contain whitespace. By convention, it is usually prefixed
by the name of the pass that uses it, e.g. 'opt.did_something'. If the value
contains whitespace, it must be enclosed in double quotes.
\end{lstlisting}
\section{script -- execute commands from file or wire}
\label{cmd:script}
\begin{lstlisting}[numbers=left,frame=single]
script <filename> [<from_label>:<to_label>]
script -scriptwire [selection]
This command executes the yosys commands in the specified file (default
behaviour), or commands embedded in the constant text value connected to the
selected wires.
In the default (file) case, the 2nd argument can be used to only execute the
section of the file between the specified labels. An empty from label is
synonymous with the beginning of the file and an empty to label is synonymous
with the end of the file.
If only one label is specified (without ':') then only the block
marked with that label (until the next label) is executed.
In "-scriptwire" mode, the commands on the selected wire(s) will be executed
in the scope of (and thus, relative to) the wires' owning module(s). This
'-module' mode can be exited by using the 'cd' command.
\end{lstlisting}
\section{select -- modify and view the list of selected objects}
\label{cmd:select}
\begin{lstlisting}[numbers=left,frame=single]
select [ -add | -del | -set <name> ] {-read <filename> | <selection>}
select [ -unset <name> ]
select [ <assert_option> ] {-read <filename> | <selection>}
select [ -list | -write <filename> | -count | -clear ]
select -module <modname>
Most commands use the list of currently selected objects to determine which part
of the design to operate on. This command can be used to modify and view this
list of selected objects.
Note that many commands support an optional [selection] argument that can be
used to override the global selection for the command. The syntax of this
optional argument is identical to the syntax of the <selection> argument
described here.
-add, -del
add or remove the given objects to the current selection.
without this options the current selection is replaced.
-set <name>
do not modify the current selection. instead save the new selection
under the given name (see @<name> below). to save the current selection,
use "select -set <name> %"
-unset <name>
do not modify the current selection. instead remove a previously saved
selection under the given name (see @<name> below).
-assert-none
do not modify the current selection. instead assert that the given
selection is empty. i.e. produce an error if any object matching the
selection is found.
-assert-any
do not modify the current selection. instead assert that the given
selection is non-empty. i.e. produce an error if no object matching
the selection is found.
-assert-count N
do not modify the current selection. instead assert that the given
selection contains exactly N objects.
-assert-max N
do not modify the current selection. instead assert that the given
selection contains less than or exactly N objects.
-assert-min N
do not modify the current selection. instead assert that the given
selection contains at least N objects.
-list
list all objects in the current selection
-write <filename>
like -list but write the output to the specified file
-read <filename>
read the specified file (written by -write)
-count
count all objects in the current selection
-clear
clear the current selection. this effectively selects the whole
design. it also resets the selected module (see -module). use the
command 'select *' to select everything but stay in the current module.
-none
create an empty selection. the current module is unchanged.
-module <modname>
limit the current scope to the specified module.
the difference between this and simply selecting the module
is that all object names are interpreted relative to this
module after this command until the selection is cleared again.
When this command is called without an argument, the current selection
is displayed in a compact form (i.e. only the module name when a whole module
is selected).
The <selection> argument itself is a series of commands for a simple stack
machine. Each element on the stack represents a set of selected objects.
After this commands have been executed, the union of all remaining sets
on the stack is computed and used as selection for the command.
Pushing (selecting) object when not in -module mode:
<mod_pattern>
select the specified module(s)
<mod_pattern>/<obj_pattern>
select the specified object(s) from the module(s)
Pushing (selecting) object when in -module mode:
<obj_pattern>
select the specified object(s) from the current module
By default, patterns will not match black/white-box modules or theircontents. To include such objects, prefix the pattern with '='.
A <mod_pattern> can be a module name, wildcard expression (*, ?, [..])
matching module names, or one of the following:
A:<pattern>, A:<pattern>=<pattern>
all modules with an attribute matching the given pattern
in addition to = also <, <=, >=, and > are supported
N:<pattern>
all modules with a name matching the given pattern
(i.e. 'N:' is optional as it is the default matching rule)
An <obj_pattern> can be an object name, wildcard expression, or one of
the following:
w:<pattern>
all wires with a name matching the given wildcard pattern
i:<pattern>, o:<pattern>, x:<pattern>
all inputs (i:), outputs (o:) or any ports (x:) with matching names
s:<size>, s:<min>:<max>
all wires with a matching width
m:<pattern>
all memories with a name matching the given pattern
c:<pattern>
all cells with a name matching the given pattern
t:<pattern>
all cells with a type matching the given pattern
p:<pattern>
all processes with a name matching the given pattern
a:<pattern>
all objects with an attribute name matching the given pattern
a:<pattern>=<pattern>
all objects with a matching attribute name-value-pair.
in addition to = also <, <=, >=, and > are supported
r:<pattern>, r:<pattern>=<pattern>
cells with matching parameters. also with <, <=, >= and >.
n:<pattern>
all objects with a name matching the given pattern
(i.e. 'n:' is optional as it is the default matching rule)
@<name>
push the selection saved prior with 'select -set <name> ...'
The following actions can be performed on the top sets on the stack:
%
push a copy of the current selection to the stack
%%
replace the stack with a union of all elements on it
%n
replace top set with its invert
%u
replace the two top sets on the stack with their union
%i
replace the two top sets on the stack with their intersection
%d
pop the top set from the stack and subtract it from the new top
%D
like %d but swap the roles of two top sets on the stack
%c
create a copy of the top set from the stack and push it
%x[<num1>|*][.<num2>][:<rule>[:<rule>..]]
expand top set <num1> num times according to the specified rules.
(i.e. select all cells connected to selected wires and select all
wires connected to selected cells) The rules specify which cell
ports to use for this. the syntax for a rule is a '-' for exclusion
and a '+' for inclusion, followed by an optional comma separated
list of cell types followed by an optional comma separated list of
cell ports in square brackets. a rule can also be just a cell or wire
name that limits the expansion (is included but does not go beyond).
select at most <num2> objects. a warning message is printed when this
limit is reached. When '*' is used instead of <num1> then the process
is repeated until no further object are selected.
%ci[<num1>|*][.<num2>][:<rule>[:<rule>..]]
%co[<num1>|*][.<num2>][:<rule>[:<rule>..]]
similar to %x, but only select input (%ci) or output cones (%co)
%xe[...] %cie[...] %coe
like %x, %ci, and %co but only consider combinatorial cells
%a
expand top set by selecting all wires that are (at least in part)
aliases for selected wires.
%s
expand top set by adding all modules that implement cells in selected
modules
%m
expand top set by selecting all modules that contain selected objects
%M
select modules that implement selected cells
%C
select cells that implement selected modules
%R[<num>]
select <num> random objects from top selection (default 1)
Example: the following command selects all wires that are connected to a
'GATE' input of a 'SWITCH' cell:
select */t:SWITCH %x:+[GATE] */t:SWITCH %d
\end{lstlisting}
\section{setattr -- set/unset attributes on objects}
\label{cmd:setattr}
\begin{lstlisting}[numbers=left,frame=single]
setattr [ -mod ] [ -set name value | -unset name ]... [selection]
Set/unset the given attributes on the selected objects. String values must be
passed in double quotes (").
When called with -mod, this command will set and unset attributes on modules
instead of objects within modules.
\end{lstlisting}
\section{setparam -- set/unset parameters on objects}
\label{cmd:setparam}
\begin{lstlisting}[numbers=left,frame=single]
setparam [ -type cell_type ] [ -set name value | -unset name ]... [selection]
Set/unset the given parameters on the selected cells. String values must be
passed in double quotes (").
The -type option can be used to change the cell type of the selected cells.
\end{lstlisting}
\section{setundef -- replace undef values with defined constants}
\label{cmd:setundef}
\begin{lstlisting}[numbers=left,frame=single]
setundef [options] [selection]
This command replaces undef (x) constants with defined (0/1) constants.
-undriven
also set undriven nets to constant values
-expose
also expose undriven nets as inputs (use with -undriven)
-zero
replace with bits cleared (0)
-one
replace with bits set (1)
-undef
replace with undef (x) bits, may be used with -undriven
-anyseq
replace with $anyseq drivers (for formal)
-anyconst
replace with $anyconst drivers (for formal)
-random <seed>
replace with random bits using the specified integer as seed
value for the random number generator.
-init
also create/update init values for flip-flops
-params
replace undef in cell parameters
\end{lstlisting}
\section{share -- perform sat-based resource sharing}
\label{cmd:share}
\begin{lstlisting}[numbers=left,frame=single]
share [options] [selection]
This pass merges shareable resources into a single resource. A SAT solver
is used to determine if two resources are share-able.
-force
Per default the selection of cells that is considered for sharing is
narrowed using a list of cell types. With this option all selected
cells are considered for resource sharing.
IMPORTANT NOTE: If the -all option is used then no cells with internal
state must be selected!
-aggressive
Per default some heuristics are used to reduce the number of cells
considered for resource sharing to only large resources. This options
turns this heuristics off, resulting in much more cells being considered
for resource sharing.
-fast
Only consider the simple part of the control logic in SAT solving, resulting
in much easier SAT problems at the cost of maybe missing some opportunities
for resource sharing.
-limit N
Only perform the first N merges, then stop. This is useful for debugging.
\end{lstlisting}
\section{shell -- enter interactive command mode}
\label{cmd:shell}
\begin{lstlisting}[numbers=left,frame=single]
shell
This command enters the interactive command mode. This can be useful
in a script to interrupt the script at a certain point and allow for
interactive inspection or manual synthesis of the design at this point.
The command prompt of the interactive shell indicates the current
selection (see 'help select'):
yosys>
the entire design is selected
yosys*>
only part of the design is selected
yosys [modname]>
the entire module 'modname' is selected using 'select -module modname'
yosys [modname]*>
only part of current module 'modname' is selected
When in interactive shell, some errors (e.g. invalid command arguments)
do not terminate yosys but return to the command prompt.
This command is the default action if nothing else has been specified
on the command line.
Press Ctrl-D or type 'exit' to leave the interactive shell.
\end{lstlisting}
\section{show -- generate schematics using graphviz}
\label{cmd:show}
\begin{lstlisting}[numbers=left,frame=single]
show [options] [selection]
Create a graphviz DOT file for the selected part of the design and compile it
to a graphics file (usually SVG or PostScript).
-viewer <viewer>
Run the specified command with the graphics file as parameter.
On Windows, this pauses yosys until the viewer exits.
-format <format>
Generate a graphics file in the specified format. Use 'dot' to just
generate a .dot file, or other <format> strings such as 'svg' or 'ps'
to generate files in other formats (this calls the 'dot' command).
-lib <verilog_or_rtlil_file>
Use the specified library file for determining whether cell ports are
inputs or outputs. This option can be used multiple times to specify
more than one library.
note: in most cases it is better to load the library before calling
show with 'read_verilog -lib <filename>'. it is also possible to
load liberty files with 'read_liberty -lib <filename>'.
-prefix <prefix>
generate <prefix>.* instead of ~/.yosys_show.*
-color <color> <object>
assign the specified color to the specified object. The object can be
a single selection wildcard expressions or a saved set of objects in
the @<name> syntax (see "help select" for details).
-label <text> <object>
assign the specified label text to the specified object. The object can
be a single selection wildcard expressions or a saved set of objects in
the @<name> syntax (see "help select" for details).
-colors <seed>
Randomly assign colors to the wires. The integer argument is the seed
for the random number generator. Change the seed value if the colored
graph still is ambiguous. A seed of zero deactivates the coloring.
-colorattr <attribute_name>
Use the specified attribute to assign colors. A unique color is
assigned to each unique value of this attribute.
-width
annotate buses with a label indicating the width of the bus.
-signed
mark ports (A, B) that are declared as signed (using the [AB]_SIGNED
cell parameter) with an asterisk next to the port name.
-stretch
stretch the graph so all inputs are on the left side and all outputs
(including inout ports) are on the right side.
-pause
wait for the user to press enter to before returning
-enum
enumerate objects with internal ($-prefixed) names
-long
do not abbreviate objects with internal ($-prefixed) names
-notitle
do not add the module name as graph title to the dot file
-nobg
don't run viewer in the background, IE wait for the viewer tool to
exit before returning
When no <format> is specified, 'dot' is used. When no <format> and <viewer> is
specified, 'xdot' is used to display the schematic (POSIX systems only).
The generated output files are '~/.yosys_show.dot' and '~/.yosys_show.<format>',
unless another prefix is specified using -prefix <prefix>.
Yosys on Windows and YosysJS use different defaults: The output is written
to 'show.dot' in the current directory and new viewer is launched each time
the 'show' command is executed.
\end{lstlisting}
\section{shregmap -- map shift registers}
\label{cmd:shregmap}
\begin{lstlisting}[numbers=left,frame=single]
shregmap [options] [selection]
This pass converts chains of $_DFF_[NP]_ gates to target specific shift register
primitives. The generated shift register will be of type $__SHREG_DFF_[NP]_ and
will use the same interface as the original $_DFF_*_ cells. The cell parameter
'DEPTH' will contain the depth of the shift register. Use a target-specific
'techmap' map file to convert those cells to the actual target cells.
-minlen N
minimum length of shift register (default = 2)
(this is the length after -keep_before and -keep_after)
-maxlen N
maximum length of shift register (default = no limit)
larger chains will be mapped to multiple shift register instances
-keep_before N
number of DFFs to keep before the shift register (default = 0)
-keep_after N
number of DFFs to keep after the shift register (default = 0)
-clkpol pos|neg|any
limit match to only positive or negative edge clocks. (default = any)
-enpol pos|neg|none|any_or_none|any
limit match to FFs with the specified enable polarity. (default = none)
-match <cell_type>[:<d_port_name>:<q_port_name>]
match the specified cells instead of $_DFF_N_ and $_DFF_P_. If
':<d_port_name>:<q_port_name>' is omitted then 'D' and 'Q' is used
by default. E.g. the option '-clkpol pos' is just an alias for
'-match $_DFF_P_', which is an alias for '-match $_DFF_P_:D:Q'.
-params
instead of encoding the clock and enable polarity in the cell name by
deriving from the original cell name, simply name all generated cells
$__SHREG_ and use CLKPOL and ENPOL parameters. An ENPOL value of 2 is
used to denote cells without enable input. The ENPOL parameter is
omitted when '-enpol none' (or no -enpol option) is passed.
-zinit
assume the shift register is automatically zero-initialized, so it
becomes legal to merge zero initialized FFs into the shift register.
-init
map initialized registers to the shift reg, add an INIT parameter to
generated cells with the initialization value. (first bit to shift out
in LSB position)
-tech greenpak4
map to greenpak4 shift registers.
\end{lstlisting}
\section{sim -- simulate the circuit}
\label{cmd:sim}
\begin{lstlisting}[numbers=left,frame=single]
sim [options] [top-level]
This command simulates the circuit using the given top-level module.
-vcd <filename>
write the simulation results to the given VCD file
-clock <portname>
name of top-level clock input
-clockn <portname>
name of top-level clock input (inverse polarity)
-reset <portname>
name of top-level reset input (active high)
-resetn <portname>
name of top-level inverted reset input (active low)
-rstlen <integer>
number of cycles reset should stay active (default: 1)
-zinit
zero-initialize all uninitialized regs and memories
-timescale <string>
include the specified timescale declaration in the vcd
-n <integer>
number of cycles to simulate (default: 20)
-a
include all nets in VCD output, not just those with public names
-w
writeback mode: use final simulation state as new init state
-d
enable debug output
\end{lstlisting}
\section{simplemap -- mapping simple coarse-grain cells}
\label{cmd:simplemap}
\begin{lstlisting}[numbers=left,frame=single]
simplemap [selection]
This pass maps a small selection of simple coarse-grain cells to yosys gate
primitives. The following internal cell types are mapped by this pass:
$not, $pos, $and, $or, $xor, $xnor
$reduce_and, $reduce_or, $reduce_xor, $reduce_xnor, $reduce_bool
$logic_not, $logic_and, $logic_or, $mux, $tribuf
$sr, $ff, $dff, $dffe, $dffsr, $dffsre, $adff, $adffe, $aldff, $aldffe, $sdff, $sdffe, $sdffce, $dlatch, $adlatch, $dlatchsr
\end{lstlisting}
\section{splice -- create explicit splicing cells}
\label{cmd:splice}
\begin{lstlisting}[numbers=left,frame=single]
splice [options] [selection]
This command adds $slice and $concat cells to the design to make the splicing
of multi-bit signals explicit. This for example is useful for coarse grain
synthesis, where dedicated hardware is needed to splice signals.
-sel_by_cell
only select the cell ports to rewire by the cell. if the selection
contains a cell, than all cell inputs are rewired, if necessary.
-sel_by_wire
only select the cell ports to rewire by the wire. if the selection
contains a wire, than all cell ports driven by this wire are wired,
if necessary.
-sel_any_bit
it is sufficient if the driver of any bit of a cell port is selected.
by default all bits must be selected.
-wires
also add $slice and $concat cells to drive otherwise unused wires.
-no_outputs
do not rewire selected module outputs.
-port <name>
only rewire cell ports with the specified name. can be used multiple
times. implies -no_output.
-no_port <name>
do not rewire cell ports with the specified name. can be used multiple
times. can not be combined with -port <name>.
By default selected output wires and all cell ports of selected cells driven
by selected wires are rewired.
\end{lstlisting}
\section{splitnets -- split up multi-bit nets}
\label{cmd:splitnets}
\begin{lstlisting}[numbers=left,frame=single]
splitnets [options] [selection]
This command splits multi-bit nets into single-bit nets.
-format char1[char2[char3]]
the first char is inserted between the net name and the bit index, the
second char is appended to the netname. e.g. -format () creates net
names like 'mysignal(42)'. the 3rd character is the range separation
character when creating multi-bit wires. the default is '[]:'.
-ports
also split module ports. per default only internal signals are split.
-driver
don't blindly split nets in individual bits. instead look at the driver
and split nets so that no driver drives only part of a net.
\end{lstlisting}
\section{sta -- perform static timing analysis}
\label{cmd:sta}
\begin{lstlisting}[numbers=left,frame=single]
sta [options] [selection]
This command performs static timing analysis on the design. (Only considers
paths within a single module, so the design must be flattened.)
\end{lstlisting}
\section{stat -- print some statistics}
\label{cmd:stat}
\begin{lstlisting}[numbers=left,frame=single]
stat [options] [selection]
Print some statistics (number of objects) on the selected portion of the
design.
-top <module>
print design hierarchy with this module as top. if the design is fully
selected and a module has the 'top' attribute set, this module is used
default value for this option.
-liberty <liberty_file>
use cell area information from the provided liberty file
-tech <technology>
print area estemate for the specified technology. Currently supported
values for <technology>: xilinx, cmos
-width
annotate internal cell types with their word width.
e.g. $add_8 for an 8 bit wide $add cell.
\end{lstlisting}
\section{submod -- moving part of a module to a new submodule}
\label{cmd:submod}
\begin{lstlisting}[numbers=left,frame=single]
submod [options] [selection]
This pass identifies all cells with the 'submod' attribute and moves them to
a newly created module. The value of the attribute is used as name for the
cell that replaces the group of cells with the same attribute value.
This pass can be used to create a design hierarchy in flat design. This can
be useful for analyzing or reverse-engineering a design.
This pass only operates on completely selected modules with no processes
or memories.
-copy
by default the cells are 'moved' from the source module and the source
module will use an instance of the new module after this command is
finished. call with -copy to not modify the source module.
-name <name>
don't use the 'submod' attribute but instead use the selection. only
objects from one module might be selected. the value of the -name option
is used as the value of the 'submod' attribute instead.
-hidden
instead of creating submodule ports with public names, create ports with
private names so that a subsequent 'flatten; clean' call will restore the
original module with original public names.
\end{lstlisting}
\section{supercover -- add hi/lo cover cells for each wire bit}
\label{cmd:supercover}
\begin{lstlisting}[numbers=left,frame=single]
supercover [options] [selection]
This command adds two cover cells for each bit of each selected wire, one
checking for a hi signal level and one checking for lo level.
\end{lstlisting}
\section{synth -- generic synthesis script}
\label{cmd:synth}
\begin{lstlisting}[numbers=left,frame=single]
synth [options]
This command runs the default synthesis script. This command does not operate
on partly selected designs.
-top <module>
use the specified module as top module (default='top')
-auto-top
automatically determine the top of the design hierarchy
-flatten
flatten the design before synthesis. this will pass '-auto-top' to
'hierarchy' if no top module is specified.
-encfile <file>
passed to 'fsm_recode' via 'fsm'
-lut <k>
perform synthesis for a k-LUT architecture.
-nofsm
do not run FSM optimization
-noabc
do not run abc (as if yosys was compiled without ABC support)
-noalumacc
do not run 'alumacc' pass. i.e. keep arithmetic operators in
their direct form ($add, $sub, etc.).
-nordff
passed to 'memory'. prohibits merging of FFs into memory read ports
-noshare
do not run SAT-based resource sharing
-run <from_label>[:<to_label>]
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-abc9
use new ABC9 flow (EXPERIMENTAL)
-flowmap
use FlowMap LUT techmapping instead of ABC
The following commands are executed by this synthesis command:
begin:
hierarchy -check [-top <top> | -auto-top]
coarse:
proc
flatten (if -flatten)
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm (unless -nofsm)
opt
wreduce
peepopt
opt_clean
techmap -map +/cmp2lut.v -map +/cmp2lcu.v (if -lut)
alumacc (unless -noalumacc)
share (unless -noshare)
opt
memory -nomap
opt_clean
fine:
opt -fast -full
memory_map
opt -full
techmap
techmap -map +/gate2lut.v (if -noabc and -lut)
clean; opt_lut (if -noabc and -lut)
flowmap -maxlut K (if -flowmap and -lut)
opt -fast
abc -fast (unless -noabc, unless -lut)
abc -fast -lut k (unless -noabc, if -lut)
opt -fast (unless -noabc)
check:
hierarchy -check
stat
check
\end{lstlisting}
\section{synth\_achronix -- synthesis for Acrhonix Speedster22i FPGAs.}
\label{cmd:synth_achronix}
\begin{lstlisting}[numbers=left,frame=single]
synth_achronix [options]
This command runs synthesis for Achronix Speedster eFPGAs. This work is still experimental.
-top <module>
use the specified module as top module (default='top')
-vout <file>
write the design to the specified Verilog netlist file. writing of an
output file is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
The following commands are executed by this synthesis command:
begin:
read_verilog -sv -lib +/achronix/speedster22i/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
fine:
opt -fast -mux_undef -undriven -fine -full
memory_map
opt -undriven -fine
opt -fine
techmap -map +/techmap.v
opt -full
clean -purge
setundef -undriven -zero
dfflegalize -cell $_DFF_P_ x
abc -markgroups -dff -D 1 (only if -retime)
map_luts:
abc -lut 4
clean
map_cells:
iopadmap -bits -outpad $__outpad I:O -inpad $__inpad O:I
techmap -map +/achronix/speedster22i/cells_map.v
clean -purge
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
vout:
write_verilog -nodec -attr2comment -defparam -renameprefix syn_ <file-name>
\end{lstlisting}
\section{synth\_anlogic -- synthesis for Anlogic FPGAs}
\label{cmd:synth_anlogic}
\begin{lstlisting}[numbers=left,frame=single]
synth_anlogic [options]
This command runs synthesis for Anlogic FPGAs.
-top <module>
use the specified module as top module
-edif <file>
write the design to the specified EDIF file. writing of an output file
is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
-nolutram
do not use EG_LOGIC_DRAM16X4 cells in output netlist
The following commands are executed by this synthesis command:
begin:
read_verilog -lib +/anlogic/cells_sim.v +/anlogic/eagle_bb.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
map_lutram: (skip if -nolutram)
memory_bram -rules +/anlogic/lutrams.txt
techmap -map +/anlogic/lutrams_map.v
setundef -zero -params t:EG_LOGIC_DRAM16X4
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
map_gates:
techmap -map +/techmap.v -map +/anlogic/arith_map.v
opt -fast
abc -dff -D 1 (only if -retime)
map_ffs:
dfflegalize -cell $_DFFE_P??P_ r -cell $_SDFFE_P??P_ r -cell $_DLATCH_N??_ r
techmap -D NO_LUT -map +/anlogic/cells_map.v
opt_expr -mux_undef
simplemap
map_luts:
abc -lut 4:6
clean
map_cells:
techmap -map +/anlogic/cells_map.v
clean
map_anlogic:
anlogic_fixcarry
anlogic_eqn
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
edif:
write_edif <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_coolrunner2 -- synthesis for Xilinx Coolrunner-II CPLDs}
\label{cmd:synth_coolrunner2}
\begin{lstlisting}[numbers=left,frame=single]
synth_coolrunner2 [options]
This command runs synthesis for Coolrunner-II CPLDs. This work is experimental.
It is intended to be used with https://github.com/azonenberg/openfpga as the
place-and-route.
-top <module>
use the specified module as top module (default='top')
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
The following commands are executed by this synthesis command:
begin:
read_verilog -lib +/coolrunner2/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
coarse:
synth -run coarse
fine:
extract_counter -dir up -allow_arst no
techmap -map +/coolrunner2/cells_counter_map.v
clean
opt -fast -full
techmap -map +/techmap.v -map +/coolrunner2/cells_latch.v
opt -fast
dfflibmap -prepare -liberty +/coolrunner2/xc2_dff.lib
map_tff:
abc -g AND,XOR
clean
extract -map +/coolrunner2/tff_extract.v
map_pla:
abc -sop -I 40 -P 56
clean
map_cells:
dfflibmap -liberty +/coolrunner2/xc2_dff.lib
dffinit -ff FDCP Q INIT
dffinit -ff FDCP_N Q INIT
dffinit -ff FTCP Q INIT
dffinit -ff FTCP_N Q INIT
dffinit -ff LDCP Q INIT
dffinit -ff LDCP_N Q INIT
coolrunner2_sop
clean
iopadmap -bits -inpad IBUF O:I -outpad IOBUFE I:IO -inoutpad IOBUFE O:IO -toutpad IOBUFE E:I:IO -tinoutpad IOBUFE E:O:I:IO
attrmvcp -attr src -attr LOC t:IOBUFE n:*
attrmvcp -attr src -attr LOC -driven t:IBUF n:*
coolrunner2_fixup
splitnets
clean
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_easic -- synthesis for eASIC platform}
\label{cmd:synth_easic}
\begin{lstlisting}[numbers=left,frame=single]
synth_easic [options]
This command runs synthesis for eASIC platform.
-top <module>
use the specified module as top module
-vlog <file>
write the design to the specified structural Verilog file. writing of
an output file is omitted if this parameter is not specified.
-etools <path>
set path to the eTools installation. (default=/opt/eTools)
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
The following commands are executed by this synthesis command:
begin:
read_liberty -lib <etools_phys_clk_lib>
read_liberty -lib <etools_logic_lut_lib>
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
coarse:
synth -run coarse
fine:
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
techmap
opt -fast
abc -dff -D 1 (only if -retime)
opt_clean (only if -retime)
map:
dfflibmap -liberty <etools_phys_clk_lib>
abc -liberty <etools_logic_lut_lib>
opt_clean
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
vlog:
write_verilog -noexpr -attr2comment <file-name>
\end{lstlisting}
\section{synth\_ecp5 -- synthesis for ECP5 FPGAs}
\label{cmd:synth_ecp5}
\begin{lstlisting}[numbers=left,frame=single]
synth_ecp5 [options]
This command runs synthesis for ECP5 FPGAs.
-top <module>
use the specified module as top module
-blif <file>
write the design to the specified BLIF file. writing of an output file
is omitted if this parameter is not specified.
-edif <file>
write the design to the specified EDIF file. writing of an output file
is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-dff
run 'abc'/'abc9' with -dff option
-retime
run 'abc' with '-dff -D 1' options
-noccu2
do not use CCU2 cells in output netlist
-nodffe
do not use flipflops with CE in output netlist
-nobram
do not use block RAM cells in output netlist
-nolutram
do not use LUT RAM cells in output netlist
-nowidelut
do not use PFU muxes to implement LUTs larger than LUT4s
-asyncprld
use async PRLD mode to implement ALDFF (EXPERIMENTAL)
-abc2
run two passes of 'abc' for slightly improved logic density
-abc9
use new ABC9 flow (EXPERIMENTAL)
-vpr
generate an output netlist (and BLIF file) suitable for VPR
(this feature is experimental and incomplete)
-nodsp
do not map multipliers to MULT18X18D
The following commands are executed by this synthesis command:
begin:
read_verilog -lib -specify +/ecp5/cells_sim.v +/ecp5/cells_bb.v
hierarchy -check -top <top>
coarse:
proc
flatten
tribuf -logic
deminout
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce
peepopt
opt_clean
share
techmap -map +/cmp2lut.v -D LUT_WIDTH=4
opt_expr
opt_clean
techmap -map +/mul2dsp.v -map +/ecp5/dsp_map.v -D DSP_A_MAXWIDTH=18 -D DSP_B_MAXWIDTH=18 -D DSP_A_MINWIDTH=2 -D DSP_B_MINWIDTH=2 -D DSP_NAME=$__MUL18X18 (unless -nodsp)
chtype -set $mul t:$__soft_mul (unless -nodsp)
alumacc
opt
memory -nomap
opt_clean
map_bram: (skip if -nobram)
memory_bram -rules +/ecp5/brams.txt
techmap -map +/ecp5/brams_map.v
map_lutram: (skip if -nolutram)
memory_bram -rules +/ecp5/lutrams.txt
techmap -map +/ecp5/lutrams_map.v
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map -iattr -attr !ram_block -attr !rom_block -attr logic_block -attr syn_ramstyle=auto -attr syn_ramstyle=registers -attr syn_romstyle=auto -attr syn_romstyle=logic
opt -undriven -fine
map_gates:
techmap -map +/techmap.v -map +/ecp5/arith_map.v
opt -fast
abc -dff -D 1 (only if -retime)
map_ffs:
opt_clean
dfflegalize -cell $_DFF_?_ 01 -cell $_DFF_?P?_ r -cell $_SDFF_?P?_ r [-cell $_DFFE_??_ 01 -cell $_DFFE_?P??_ r -cell $_SDFFE_?P??_ r] [-cell $_ALDFF_?P_ x -cell $_ALDFFE_?P?_ x] [-cell $_DLATCH_?_ x] ($_ALDFF_*_ only if -asyncprld, $_DLATCH_* only if not -asyncprld, $_*DFFE_* only if not -nodffe)
zinit -all w:* t:$_DFF_?_ t:$_DFFE_??_ t:$_SDFF* (only if -abc9 and -dff)
techmap -D NO_LUT -map +/ecp5/cells_map.v
opt_expr -undriven -mux_undef
simplemap
ecp5_gsr
attrmvcp -copy -attr syn_useioff
opt_clean
map_luts:
abc (only if -abc2)
techmap -map +/ecp5/latches_map.v (skip if -asyncprld)
abc -dress -lut 4:7
clean
map_cells:
techmap -map +/ecp5/cells_map.v (skip if -vpr)
opt_lut_ins -tech ecp5
clean
check:
autoname
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
blif:
opt_clean -purge (vpr mode)
write_blif -attr -cname -conn -param <file-name> (vpr mode)
write_blif -gates -attr -param <file-name> (non-vpr mode)
edif:
write_edif <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_efinix -- synthesis for Efinix FPGAs}
\label{cmd:synth_efinix}
\begin{lstlisting}[numbers=left,frame=single]
synth_efinix [options]
This command runs synthesis for Efinix FPGAs.
-top <module>
use the specified module as top module
-edif <file>
write the design to the specified EDIF file. writing of an output file
is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
-nobram
do not use EFX_RAM_5K cells in output netlist
The following commands are executed by this synthesis command:
begin:
read_verilog -lib +/efinix/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
memory_bram -rules +/efinix/brams.txt
techmap -map +/efinix/brams_map.v
setundef -zero -params t:EFX_RAM_5K
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
map_gates:
techmap -map +/techmap.v -map +/efinix/arith_map.v
opt -fast
abc -dff -D 1 (only if -retime)
map_ffs:
dfflegalize -cell $_DFFE_????_ 0 -cell $_SDFFE_????_ 0 -cell $_SDFFCE_????_ 0 -cell $_DLATCH_?_ x
techmap -D NO_LUT -map +/efinix/cells_map.v
opt_expr -mux_undef
simplemap
map_luts:
abc -lut 4
clean
map_cells:
techmap -map +/efinix/cells_map.v
clean
map_gbuf:
clkbufmap -buf $__EFX_GBUF O:I
techmap -map +/efinix/gbuf_map.v
efinix_fixcarry
clean
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
edif:
write_edif <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_gatemate -- synthesis for Cologne Chip GateMate FPGAs}
\label{cmd:synth_gatemate}
\begin{lstlisting}[numbers=left,frame=single]
synth_gatemate [options]
This command runs synthesis for Cologne Chip AG GateMate FPGAs.
-top <module>
use the specified module as top module.
-vlog <file>
write the design to the specified verilog file. Writing of an output
file is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. Writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). An empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis.
-nobram
do not use CC_BRAM_20K or CC_BRAM_40K cells in output netlist.
-noaddf
do not use CC_ADDF full adder cells in output netlist.
-nomult
do not use CC_MULT multiplier cells in output netlist.
-nomx8, -nomx4
do not use CC_MX{8,4} multiplexer cells in output netlist.
-dff
run 'abc' with -dff option
-retime
run 'abc' with '-dff -D 1' options
-noiopad
disable I/O buffer insertion (useful for hierarchical or
out-of-context flows).
-noclkbuf
disable automatic clock buffer insertion.
The following commands are executed by this synthesis command:
begin:
read_verilog -lib -specify +/gatemate/cells_sim.v +/gatemate/cells_bb.v
hierarchy -check -top <top>
prepare:
proc
flatten
tribuf -logic
deminout
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce
peepopt
opt_clean
muxpack
share
techmap -map +/cmp2lut.v -D LUT_WIDTH=4
opt_expr
opt_clean
map_mult: (skip if '-nomult')
techmap -map +/gatemate/mul_map.v
coarse:
alumacc
opt
memory -nomap
opt_clean
map_bram: (skip if '-nobram')
memory_bram -rules +/gatemate/brams.txt
setundef -zero -params t:$__CC_BRAM_CASCADE t:$__CC_BRAM_40K_SDP t:$__CC_BRAM_20K_SDP t:$__CC_BRAM_20K_TDP t:$__CC_BRAM_40K_TDP
techmap -map +/gatemate/brams_map.v
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
map_gates:
techmap -map +/techmap.v -map +/gatemate/arith_map.v
opt -fast
map_io: (skip if '-noiopad')
iopadmap -bits -inpad CC_IBUF Y:I -outpad CC_OBUF A:O -toutpad CC_TOBUF ~T:A:O -tinoutpad CC_IOBUF ~T:Y:A:IO
clean
map_regs:
opt_clean
dfflegalize -cell $_DFFE_????_ x -cell $_DLATCH_???_ x
techmap -map +/gatemate/reg_map.v
opt_expr -mux_undef
simplemap
opt_clean
map_muxs:
muxcover -mux4 -mux8
opt -full
techmap -map +/gatemate/mux_map.v
map_luts:
abc -dress -lut 4
clean
map_cells:
techmap -map +/gatemate/lut_map.v
clean
map_bufg: (skip if '-noclkbuf')
clkbufmap -buf CC_BUFG O:I
clean
check:
hierarchy -check
stat -width
check -noinit
blackbox =A:whitebox
vlog:
opt_clean -purge
write_verilog -noattr <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_gowin -- synthesis for Gowin FPGAs}
\label{cmd:synth_gowin}
\begin{lstlisting}[numbers=left,frame=single]
synth_gowin [options]
This command runs synthesis for Gowin FPGAs. This work is experimental.
-top <module>
use the specified module as top module (default='top')
-vout <file>
write the design to the specified Verilog netlist file. writing of an
output file is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON netlist file. writing of an
output file is omitted if this parameter is not specified.
This disables features not yet supported by nexpnr-gowin.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-nodffe
do not use flipflops with CE in output netlist
-nobram
do not use BRAM cells in output netlist
-nolutram
do not use distributed RAM cells in output netlist
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
-nowidelut
do not use muxes to implement LUTs larger than LUT4s
-noiopads
do not emit IOB at top level ports
-noalu
do not use ALU cells
-abc9
use new ABC9 flow (EXPERIMENTAL)
The following commands are executed by this synthesis command:
begin:
read_verilog -specify -lib +/gowin/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
map_bram: (skip if -nobram)
memory_bram -rules +/gowin/brams.txt
techmap -map +/gowin/brams_map.v
map_lutram: (skip if -nolutram)
memory_bram -rules +/gowin/lutrams.txt
techmap -map +/gowin/lutrams_map.v
setundef -params -zero t:RAM16S4
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
map_gates:
techmap -map +/techmap.v -map +/gowin/arith_map.v
opt -fast
abc -dff -D 1 (only if -retime)
iopadmap -bits -inpad IBUF O:I -outpad OBUF I:O -toutpad TBUF ~OEN:I:O -tinoutpad IOBUF ~OEN:O:I:IO (unless -noiopads)
map_ffs:
opt_clean
dfflegalize -cell $_DFF_?_ 0 -cell $_DFFE_?P_ 0 -cell $_SDFF_?P?_ r -cell $_SDFFE_?P?P_ r -cell $_DFF_?P?_ r -cell $_DFFE_?P?P_ r
techmap -map +/gowin/cells_map.v
opt_expr -mux_undef
simplemap
map_luts:
abc -lut 4:8
clean
map_cells:
techmap -map +/gowin/cells_map.v
opt_lut_ins -tech gowin
setundef -undriven -params -zero
hilomap -singleton -hicell VCC V -locell GND G
splitnets -ports (only if -vout used)
clean
autoname
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
vout:
write_verilog -simple-lhs -decimal -attr2comment -defparam -renameprefix gen <file-name>
write_json <file-name>
\end{lstlisting}
\section{synth\_greenpak4 -- synthesis for GreenPAK4 FPGAs}
\label{cmd:synth_greenpak4}
\begin{lstlisting}[numbers=left,frame=single]
synth_greenpak4 [options]
This command runs synthesis for GreenPAK4 FPGAs. This work is experimental.
It is intended to be used with https://github.com/azonenberg/openfpga as the
place-and-route.
-top <module>
use the specified module as top module (default='top')
-part <part>
synthesize for the specified part. Valid values are SLG46140V,
SLG46620V, and SLG46621V (default).
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
The following commands are executed by this synthesis command:
begin:
read_verilog -lib +/greenpak4/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
coarse:
synth -run coarse
fine:
extract_counter -pout GP_DCMP,GP_DAC -maxwidth 14
clean
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
techmap -map +/techmap.v -map +/greenpak4/cells_latch.v
dfflibmap -prepare -liberty +/greenpak4/gp_dff.lib
opt -fast -noclkinv -noff
abc -dff -D 1 (only if -retime)
map_luts:
nlutmap -assert -luts 0,6,8,2 (for -part SLG46140V)
nlutmap -assert -luts 2,8,16,2 (for -part SLG46620V)
nlutmap -assert -luts 2,8,16,2 (for -part SLG46621V)
clean
map_cells:
shregmap -tech greenpak4
dfflibmap -liberty +/greenpak4/gp_dff.lib
dffinit -ff GP_DFF Q INIT
dffinit -ff GP_DFFR Q INIT
dffinit -ff GP_DFFS Q INIT
dffinit -ff GP_DFFSR Q INIT
iopadmap -bits -inpad GP_IBUF OUT:IN -outpad GP_OBUF IN:OUT -inoutpad GP_OBUF OUT:IN -toutpad GP_OBUFT OE:IN:OUT -tinoutpad GP_IOBUF OE:OUT:IN:IO
attrmvcp -attr src -attr LOC t:GP_OBUF t:GP_OBUFT t:GP_IOBUF n:*
attrmvcp -attr src -attr LOC -driven t:GP_IBUF n:*
techmap -map +/greenpak4/cells_map.v
greenpak4_dffinv
clean
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_ice40 -- synthesis for iCE40 FPGAs}
\label{cmd:synth_ice40}
\begin{lstlisting}[numbers=left,frame=single]
synth_ice40 [options]
This command runs synthesis for iCE40 FPGAs.
-device < hx | lp | u >
relevant only for '-abc9' flow, optimise timing for the specified device.
default: hx
-top <module>
use the specified module as top module
-blif <file>
write the design to the specified BLIF file. writing of an output file
is omitted if this parameter is not specified.
-edif <file>
write the design to the specified EDIF file. writing of an output file
is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-dff
run 'abc'/'abc9' with -dff option
-retime
run 'abc' with '-dff -D 1' options
-nocarry
do not use SB_CARRY cells in output netlist
-nodffe
do not use SB_DFFE* cells in output netlist
-dffe_min_ce_use <min_ce_use>
do not use SB_DFFE* cells if the resulting CE line would go to less
than min_ce_use SB_DFFE* in output netlist
-nobram
do not use SB_RAM40_4K* cells in output netlist
-dsp
use iCE40 UltraPlus DSP cells for large arithmetic
-noabc
use built-in Yosys LUT techmapping instead of abc
-abc2
run two passes of 'abc' for slightly improved logic density
-vpr
generate an output netlist (and BLIF file) suitable for VPR
(this feature is experimental and incomplete)
-abc9
use new ABC9 flow (EXPERIMENTAL)
-flowmap
use FlowMap LUT techmapping instead of abc (EXPERIMENTAL)
The following commands are executed by this synthesis command:
begin:
read_verilog -D ICE40_HX -lib -specify +/ice40/cells_sim.v
hierarchy -check -top <top>
proc
flatten: (unless -noflatten)
flatten
tribuf -logic
deminout
coarse:
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce
peepopt
opt_clean
share
techmap -map +/cmp2lut.v -D LUT_WIDTH=4
opt_expr
opt_clean
memory_dff
wreduce t:$mul
techmap -map +/mul2dsp.v -map +/ice40/dsp_map.v -D DSP_A_MAXWIDTH=16 -D DSP_B_MAXWIDTH=16 -D DSP_A_MINWIDTH=2 -D DSP_B_MINWIDTH=2 -D DSP_Y_MINWIDTH=11 -D DSP_NAME=$__MUL16X16 (if -dsp)
select a:mul2dsp (if -dsp)
setattr -unset mul2dsp (if -dsp)
opt_expr -fine (if -dsp)
wreduce (if -dsp)
select -clear (if -dsp)
ice40_dsp (if -dsp)
chtype -set $mul t:$__soft_mul (if -dsp)
alumacc
opt
memory -nomap
opt_clean
map_bram: (skip if -nobram)
memory_bram -rules +/ice40/brams.txt
techmap -map +/ice40/brams_map.v
ice40_braminit
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map -iattr -attr !ram_block -attr !rom_block -attr logic_block -attr syn_ramstyle=auto -attr syn_ramstyle=registers -attr syn_romstyle=auto -attr syn_romstyle=logic
opt -undriven -fine
map_gates:
ice40_wrapcarry
techmap -map +/techmap.v -map +/ice40/arith_map.v
opt -fast
abc -dff -D 1 (only if -retime)
ice40_opt
map_ffs:
dfflegalize -cell $_DFF_?_ 0 -cell $_DFFE_?P_ 0 -cell $_DFF_?P?_ 0 -cell $_DFFE_?P?P_ 0 -cell $_SDFF_?P?_ 0 -cell $_SDFFCE_?P?P_ 0 -cell $_DLATCH_?_ x -mince -1
techmap -map +/ice40/ff_map.v
opt_expr -mux_undef
simplemap
ice40_opt -full
map_luts:
abc (only if -abc2)
ice40_opt (only if -abc2)
techmap -map +/ice40/latches_map.v
simplemap (if -noabc or -flowmap)
techmap -map +/gate2lut.v -D LUT_WIDTH=4 (only if -noabc)
flowmap -maxlut 4 (only if -flowmap)
abc -dress -lut 4 (skip if -noabc)
ice40_wrapcarry -unwrap
techmap -map +/ice40/ff_map.v
clean
opt_lut -dlogic SB_CARRY:I0=1:I1=2:CI=3 -dlogic SB_CARRY:CO=3
map_cells:
techmap -map +/ice40/cells_map.v (skip if -vpr)
clean
check:
autoname
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
blif:
opt_clean -purge (vpr mode)
write_blif -attr -cname -conn -param <file-name> (vpr mode)
write_blif -gates -attr -param <file-name> (non-vpr mode)
edif:
write_edif <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_intel -- synthesis for Intel (Altera) FPGAs.}
\label{cmd:synth_intel}
\begin{lstlisting}[numbers=left,frame=single]
synth_intel [options]
This command runs synthesis for Intel FPGAs.
-family <max10 | cyclone10lp | cycloneiv | cycloneive>
generate the synthesis netlist for the specified family.
MAX10 is the default target if no family argument specified.
For Cyclone IV GX devices, use cycloneiv argument; for Cyclone IV E, use cycloneive.
For Cyclone V and Cyclone 10 GX, use the synth_intel_alm backend instead.
-top <module>
use the specified module as top module (default='top')
-vqm <file>
write the design to the specified Verilog Quartus Mapping File. Writing of an
output file is omitted if this parameter is not specified.
Note that this backend has not been tested and is likely incompatible
with recent versions of Quartus.
-vpr <file>
write BLIF files for VPR flow experiments. The synthesized BLIF output file is not
compatible with the Quartus flow. Writing of an
output file is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-iopads
use IO pad cells in output netlist
-nobram
do not use block RAM cells in output netlist
-noflatten
do not flatten design before synthesis
-retime
run 'abc' with '-dff -D 1' options
The following commands are executed by this synthesis command:
begin:
family:
read_verilog -sv -lib +/intel/max10/cells_sim.v
read_verilog -sv -lib +/intel/common/m9k_bb.v
read_verilog -sv -lib +/intel/common/altpll_bb.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
map_bram: (skip if -nobram)
memory_bram -rules +/intel/common/brams_m9k.txt (if applicable for family)
techmap -map +/intel/common/brams_map_m9k.v (if applicable for family)
map_ffram:
opt -fast -mux_undef -undriven -fine -full
memory_map
opt -undriven -fine
techmap -map +/techmap.v
opt -full
clean -purge
setundef -undriven -zero
abc -markgroups -dff -D 1 (only if -retime)
map_ffs:
dfflegalize -cell $_DFFE_PN0P_ 01
techmap -map +/intel/common/ff_map.v
map_luts:
abc -lut 4
clean
map_cells:
iopadmap -bits -outpad $__outpad I:O -inpad $__inpad O:I (if -iopads)
techmap -map +/intel/max10/cells_map.v
clean -purge
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
vqm:
write_verilog -attr2comment -defparam -nohex -decimal -renameprefix syn_ <file-name>
vpr:
opt_clean -purge
write_blif <file-name>
WARNING: THE 'synth_intel' COMMAND IS EXPERIMENTAL.
\end{lstlisting}
\section{synth\_intel\_alm -- synthesis for ALM-based Intel (Altera) FPGAs.}
\label{cmd:synth_intel_alm}
\begin{lstlisting}[numbers=left,frame=single]
synth_intel_alm [options]
This command runs synthesis for ALM-based Intel FPGAs.
-top <module>
use the specified module as top module
-family <family>
target one of:
"cyclonev" - Cyclone V (default)
"arriav" - Arria V (non-GZ) "cyclone10gx" - Cyclone 10GX
-vqm <file>
write the design to the specified Verilog Quartus Mapping File. Writing of an
output file is omitted if this parameter is not specified. Implies -quartus.
-noflatten
do not flatten design before synthesis; useful for per-module area statistics
-quartus
output a netlist using Quartus cells instead of MISTRAL_* cells
-dff
pass DFFs to ABC to perform sequential logic optimisations (EXPERIMENTAL)
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-nolutram
do not use LUT RAM cells in output netlist
-nobram
do not use block RAM cells in output netlist
-nodsp
do not map multipliers to MISTRAL_MUL cells
-noiopad
do not instantiate IO buffers
-noclkbuf
do not insert global clock buffers
The following commands are executed by this synthesis command:
begin:
read_verilog -specify -lib -D <family> +/intel_alm/common/alm_sim.v
read_verilog -specify -lib -D <family> +/intel_alm/common/dff_sim.v
read_verilog -specify -lib -D <family> +/intel_alm/common/dsp_sim.v
read_verilog -specify -lib -D <family> +/intel_alm/common/mem_sim.v
read_verilog -specify -lib -D <family> +/intel_alm/common/misc_sim.v
read_verilog -specify -lib -D <family> -icells +/intel_alm/common/abc9_model.v
read_verilog -lib +/intel/common/altpll_bb.v
read_verilog -lib +/intel_alm/common/megafunction_bb.v
hierarchy -check -top <top>
coarse:
proc
flatten (skip if -noflatten)
tribuf -logic
deminout
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce
peepopt
opt_clean
share
techmap -map +/cmp2lut.v -D LUT_WIDTH=6
opt_expr
opt_clean
techmap -map +/mul2dsp.v [...] (unless -nodsp)
alumacc
iopadmap -bits -outpad MISTRAL_OB I:PAD -inpad MISTRAL_IB O:PAD -toutpad MISTRAL_IO OE:O:PAD -tinoutpad MISTRAL_IO OE:O:I:PAD A:top (unless -noiopad)
techmap -map +/intel_alm/common/arith_alm_map.v -map +/intel_alm/common/dsp_map.v
opt
memory -nomap
opt_clean
map_bram: (skip if -nobram)
memory_bram -rules +/intel_alm/common/bram_<bram_type>.txt
techmap -map +/intel_alm/common/bram_<bram_type>_map.v
map_lutram: (skip if -nolutram)
memory_bram -rules +/intel_alm/common/lutram_mlab.txt (for Cyclone V / Cyclone 10GX)
map_ffram:
memory_map
opt -full
map_ffs:
techmap
dfflegalize -cell $_DFFE_PN0P_ 0 -cell $_SDFFCE_PP0P_ 0
techmap -map +/intel_alm/common/dff_map.v
opt -full -undriven -mux_undef
clean -purge
clkbufmap -buf MISTRAL_CLKBUF Q:A (unless -noclkbuf)
map_luts:
techmap -map +/intel_alm/common/abc9_map.v
abc9 [-dff] -maxlut 6 -W 600
techmap -map +/intel_alm/common/abc9_unmap.v
techmap -map +/intel_alm/common/alm_map.v
opt -fast
autoname
clean
check:
hierarchy -check
stat
check
blackbox =A:whitebox
quartus:
rename -hide w:*[* w:*]*
setundef -zero
hilomap -singleton -hicell __MISTRAL_VCC Q -locell __MISTRAL_GND Q
techmap -D <family> -map +/intel_alm/common/quartus_rename.v
vqm:
write_verilog -attr2comment -defparam -nohex -decimal <file-name>
\end{lstlisting}
\section{synth\_machxo2 -- synthesis for MachXO2 FPGAs. This work is experimental.}
\label{cmd:synth_machxo2}
\begin{lstlisting}[numbers=left,frame=single]
synth_machxo2 [options]
This command runs synthesis for MachXO2 FPGAs.
-top <module>
use the specified module as top module
-blif <file>
write the design to the specified BLIF file. writing of an output file
is omitted if this parameter is not specified.
-edif <file>
write the design to the specified EDIF file. writing of an output file
is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-noiopad
do not insert IO buffers
-vpr
generate an output netlist (and BLIF file) suitable for VPR
(this feature is experimental and incomplete)
The following commands are executed by this synthesis command:
begin:
read_verilog -lib -icells +/machxo2/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
fine:
memory_map
opt -full
techmap -map +/techmap.v
opt -fast
map_ios: (unless -noiopad)
iopadmap -bits -outpad $__FACADE_OUTPAD I:O -inpad $__FACADE_INPAD O:I -toutpad $__FACADE_TOUTPAD ~T:I:O -tinoutpad $__FACADE_TINOUTPAD ~T:O:I:B A:top
attrmvcp -attr src -attr LOC t:$__FACADE_OUTPAD %x:+[O] t:$__FACADE_TOUTPAD %x:+[O] t:$__FACADE_TINOUTPAD %x:+[B]
attrmvcp -attr src -attr LOC -driven t:$__FACADE_INPAD %x:+[I]
map_ffs:
dfflegalize -cell $_DFF_P_ 0
map_luts:
abc -lut 4 -dress
clean
map_cells:
techmap -map +/machxo2/cells_map.v
clean
check:
hierarchy -check
stat
blackbox =A:whitebox
blif:
opt_clean -purge (vpr mode)
write_blif -attr -cname -conn -param <file-name> (vpr mode)
write_blif -gates -attr -param <file-name> (non-vpr mode)
edif:
write_edif <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_nexus -- synthesis for Lattice Nexus FPGAs}
\label{cmd:synth_nexus}
\begin{lstlisting}[numbers=left,frame=single]
synth_nexus [options]
This command runs synthesis for Lattice Nexus FPGAs.
-top <module>
use the specified module as top module
-family <device>
run synthesis for the specified Nexus device
supported values: lifcl, lfd2nx
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-vm <file>
write the design to the specified structural Verilog file. writing of
an output file is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-dff
run 'abc'/'abc9' with -dff option
-retime
run 'abc' with '-dff -D 1' options
-noccu2
do not use CCU2 cells in output netlist
-nodffe
do not use flipflops with CE in output netlist
-nolram
do not use large RAM cells in output netlist
note that large RAM must be explicitly requested with a (* lram *)
attribute on the memory.
-nobram
do not use block RAM cells in output netlist
-nolutram
do not use LUT RAM cells in output netlist
-nowidelut
do not use PFU muxes to implement LUTs larger than LUT4s
-noiopad
do not insert IO buffers
-nodsp
do not infer DSP multipliers
-abc9
use new ABC9 flow (EXPERIMENTAL)
The following commands are executed by this synthesis command:
begin:
read_verilog -lib -specify +/nexus/cells_sim.v +/nexus/cells_xtra.v
hierarchy -check -top <top>
coarse:
proc
flatten
tribuf -logic
deminout
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce
peepopt
opt_clean
share
techmap -map +/cmp2lut.v -D LUT_WIDTH=4
opt_expr
opt_clean
techmap -map +/mul2dsp.v [...] (unless -nodsp)
techmap -map +/nexus/dsp_map.v (unless -nodsp)
alumacc
opt
memory -nomap
opt_clean
map_lram: (skip if -nolram)
memory_bram -rules +/nexus/lrams.txt
setundef -zero -params t:$__NX_PDPSC512K
techmap -map +/nexus/lrams_map.v
map_bram: (skip if -nobram)
memory_bram -rules +/nexus/brams.txt
setundef -zero -params t:$__NX_PDP16K
techmap -map +/nexus/brams_map.v
map_lutram: (skip if -nolutram)
memory_bram -rules +/nexus/lutrams.txt
setundef -zero -params t:$__NEXUS_DPR16X4
techmap -map +/nexus/lutrams_map.v
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map -iattr -attr !ram_block -attr !rom_block -attr logic_block -attr syn_ramstyle=auto -attr syn_ramstyle=registers -attr syn_romstyle=auto -attr syn_romstyle=logic
opt -undriven -fine
map_gates:
techmap -map +/techmap.v -map +/nexus/arith_map.v
iopadmap -bits -outpad OB I:O -inpad IB O:I -toutpad OBZ ~T:I:O -tinoutpad BB ~T:O:I:B A:top (skip if '-noiopad')
opt -fast
abc -dff -D 1 (only if -retime)
map_ffs:
opt_clean
dfflegalize -cell $_DFF_P_ 01 -cell $_DFF_PP?_ r -cell $_SDFF_PP?_ r -cell $_DLATCH_?_ x [-cell $_DFFE_PP_ 01 -cell $_DFFE_PP?P_ r -cell $_SDFFE_PP?P_ r] ($_*DFFE_* only if not -nodffe)
zinit -all w:* t:$_DFF_?_ t:$_DFFE_??_ t:$_SDFF* (only if -abc9 and -dff
techmap -D NO_LUT -map +/nexus/cells_map.v
opt_expr -undriven -mux_undef
simplemap
attrmvcp -copy -attr syn_useioff
opt_clean
map_luts:
techmap -map +/nexus/latches_map.v
abc -dress -lut 4:5
clean
map_cells:
techmap -map +/nexus/cells_map.v
setundef -zero
hilomap -singleton -hicell VHI Z -locell VLO Z
clean
check:
autoname
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
json:
write_json <file-name>
vm:
write_verilog <file-name>
\end{lstlisting}
\section{synth\_quicklogic -- Synthesis for QuickLogic FPGAs}
\label{cmd:synth_quicklogic}
\begin{lstlisting}[numbers=left,frame=single]
synth_quicklogic [options]
This command runs synthesis for QuickLogic FPGAs
-top <module>
use the specified module as top module
-family <family>
run synthesis for the specified QuickLogic architecture
generate the synthesis netlist for the specified family.
supported values:
- pp3: PolarPro 3
-blif <file>
write the design to the specified BLIF file. writing of an output file
is omitted if this parameter is not specified.
-verilog <file>
write the design to the specified verilog file. writing of an output file
is omitted if this parameter is not specified.
-abc
use old ABC flow, which has generally worse mapping results but is less
likely to have bugs.
The following commands are executed by this synthesis command:
begin:
read_verilog -lib -specify +/quicklogic/cells_sim.v +/quicklogic/pp3_cells_sim.v
read_verilog -lib -specify +/quicklogic/lut_sim.v
hierarchy -check -top <top>
coarse:
proc
flatten
tribuf -logic
deminout
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce
peepopt
opt_clean
share
techmap -map +/cmp2lut.v -D LUT_WIDTH=4
opt_expr
opt_clean
alumacc
pmuxtree
opt
memory -nomap
opt_clean
map_ffram:
opt -fast -mux_undef -undriven -fine
memory_map -iattr -attr !ram_block -attr !rom_block -attr logic_block -attr syn_ramstyle=auto -attr syn_ramstyle=registers -attr syn_romstyle=auto -attr syn_romstyle=logic
opt -undriven -fine
map_gates:
techmap
opt -fast
muxcover -mux8 -mux4
map_ffs:
opt_expr
dfflegalize -cell $_DFFSRE_PPPP_ 0 -cell $_DLATCH_?_ x
techmap -map +/quicklogic/pp3_cells_map.v -map +/quicklogic/pp3_ffs_map.v
opt_expr -mux_undef
map_luts:
techmap -map +/quicklogic/pp3_latches_map.v
read_verilog -lib -specify -icells +/quicklogic/abc9_model.v
techmap -map +/quicklogic/abc9_map.v
abc9 -maxlut 4 -dff
techmap -map +/quicklogic/abc9_unmap.v
clean
map_cells:
techmap -map +/quicklogic/pp3_lut_map.v
clean
check:
autoname
hierarchy -check
stat
check -noinit
iomap:
clkbufmap -inpad ckpad Q:P
iopadmap -bits -outpad outpad A:P -inpad inpad Q:P -tinoutpad bipad EN:Q:A:P A:top
finalize:
setundef -zero -params -undriven
hilomap -hicell logic_1 A -locell logic_0 A -singleton A:top
opt_clean -purge
check
blackbox =A:whitebox
blif:
write_blif -attr -param -auto-top
verilog:
\end{lstlisting}
\section{synth\_sf2 -- synthesis for SmartFusion2 and IGLOO2 FPGAs}
\label{cmd:synth_sf2}
\begin{lstlisting}[numbers=left,frame=single]
synth_sf2 [options]
This command runs synthesis for SmartFusion2 and IGLOO2 FPGAs.
-top <module>
use the specified module as top module
-edif <file>
write the design to the specified EDIF file. writing of an output file
is omitted if this parameter is not specified.
-vlog <file>
write the design to the specified Verilog file. writing of an output file
is omitted if this parameter is not specified.
-json <file>
write the design to the specified JSON file. writing of an output file
is omitted if this parameter is not specified.
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-noflatten
do not flatten design before synthesis
-noiobs
run synthesis in "block mode", i.e. do not insert IO buffers
-clkbuf
insert direct PAD->global_net buffers
-retime
run 'abc' with '-dff -D 1' options
The following commands are executed by this synthesis command:
begin:
read_verilog -lib +/sf2/cells_sim.v
hierarchy -check -top <top>
flatten: (unless -noflatten)
proc
flatten
tribuf -logic
deminout
coarse:
synth -run coarse
fine:
opt -fast -mux_undef -undriven -fine
memory_map
opt -undriven -fine
techmap -map +/techmap.v -map +/sf2/arith_map.v
opt -fast
abc -dff -D 1 (only if -retime)
map_ffs:
dfflegalize -cell $_DFFE_PN?P_ x -cell $_SDFFCE_PN?P_ x -cell $_DLATCH_PN?_ x
techmap -D NO_LUT -map +/sf2/cells_map.v
opt_expr -mux_undef
simplemap
map_luts:
abc -lut 4
clean
map_cells:
techmap -map +/sf2/cells_map.v
clean
map_iobs:
clkbufmap -buf CLKINT Y:A [-inpad CLKBUF Y:PAD] (unless -noiobs, -inpad only passed if -clkbuf)
iopadmap -bits -inpad INBUF Y:PAD -outpad OUTBUF D:PAD -toutpad TRIBUFF E:D:PAD -tinoutpad BIBUF E:Y:D:PAD (unless -noiobs
clean
check:
hierarchy -check
stat
check -noinit
blackbox =A:whitebox
edif:
write_edif -gndvccy <file-name>
vlog:
write_verilog <file-name>
json:
write_json <file-name>
\end{lstlisting}
\section{synth\_xilinx -- synthesis for Xilinx FPGAs}
\label{cmd:synth_xilinx}
\begin{lstlisting}[numbers=left,frame=single]
synth_xilinx [options]
This command runs synthesis for Xilinx FPGAs. This command does not operate on
partly selected designs. At the moment this command creates netlists that are
compatible with 7-Series Xilinx devices.
-top <module>
use the specified module as top module
-family <family>
run synthesis for the specified Xilinx architecture
generate the synthesis netlist for the specified family.
supported values:
- xcup: Ultrascale Plus
- xcu: Ultrascale
- xc7: Series 7 (default)
- xc6s: Spartan 6
- xc6v: Virtex 6
- xc5v: Virtex 5 (EXPERIMENTAL)
- xc4v: Virtex 4 (EXPERIMENTAL)
- xc3sda: Spartan 3A DSP (EXPERIMENTAL)
- xc3sa: Spartan 3A (EXPERIMENTAL)
- xc3se: Spartan 3E (EXPERIMENTAL)
- xc3s: Spartan 3 (EXPERIMENTAL)
- xc2vp: Virtex 2 Pro (EXPERIMENTAL)
- xc2v: Virtex 2 (EXPERIMENTAL)
- xcve: Virtex E, Spartan 2E (EXPERIMENTAL)
- xcv: Virtex, Spartan 2 (EXPERIMENTAL)
-edif <file>
write the design to the specified edif file. writing of an output file
is omitted if this parameter is not specified.
-blif <file>
write the design to the specified BLIF file. writing of an output file
is omitted if this parameter is not specified.
-ise
generate an output netlist suitable for ISE
-nobram
do not use block RAM cells in output netlist
-nolutram
do not use distributed RAM cells in output netlist
-nosrl
do not use distributed SRL cells in output netlist
-nocarry
do not use XORCY/MUXCY/CARRY4 cells in output netlist
-nowidelut
do not use MUXF[5-9] resources to implement LUTs larger than native for the target
-nodsp
do not use DSP48*s to implement multipliers and associated logic
-noiopad
disable I/O buffer insertion (useful for hierarchical or
out-of-context flows)
-noclkbuf
disable automatic clock buffer insertion
-uram
infer URAM288s for large memories (xcup only)
-widemux <int>
enable inference of hard multiplexer resources (MUXF[78]) for muxes at or
above this number of inputs (minimum value 2, recommended value >= 5).
default: 0 (no inference)
-run <from_label>:<to_label>
only run the commands between the labels (see below). an empty
from label is synonymous to 'begin', and empty to label is
synonymous to the end of the command list.
-flatten
flatten design before synthesis
-dff
run 'abc'/'abc9' with -dff option
-retime
run 'abc' with '-D 1' option to enable flip-flop retiming.
implies -dff.
-abc9
use new ABC9 flow (EXPERIMENTAL)
The following commands are executed by this synthesis command:
begin:
read_verilog -lib -specify +/xilinx/cells_sim.v
read_verilog -lib +/xilinx/cells_xtra.v
hierarchy -check -auto-top
prepare:
proc
flatten (with '-flatten')
tribuf -logic
deminout
opt_expr
opt_clean
check
opt -nodffe -nosdff
fsm
opt
wreduce [-keepdc] (option for '-widemux')
peepopt
opt_clean
muxpack ('-widemux' only)
pmux2shiftx (skip if '-nosrl' and '-widemux=0')
clean (skip if '-nosrl' and '-widemux=0')
map_dsp: (skip if '-nodsp')
memory_dff
techmap -map +/mul2dsp.v -map +/xilinx/{family}_dsp_map.v {options}
select a:mul2dsp
setattr -unset mul2dsp
opt_expr -fine
wreduce
select -clear
xilinx_dsp -family <family>
chtype -set $mul t:$__soft_mul
coarse:
techmap -map +/cmp2lut.v -map +/cmp2lcu.v -D LUT_WIDTH=[46]
alumacc
share
opt
memory -nomap
opt_clean
map_uram: (only if '-uram')
memory_bram -rules +/xilinx/{family}_urams.txt
techmap -map +/xilinx/{family}_urams_map.v
map_bram: (skip if '-nobram')
memory_bram -rules +/xilinx/{family}_brams.txt
techmap -map +/xilinx/{family}_brams_map.v
map_lutram: (skip if '-nolutram')
memory_bram -rules +/xilinx/lut[46]_lutrams.txt
techmap -map +/xilinx/lutrams_map.v
map_ffram:
opt -fast -full
memory_map
fine:
simplemap t:$mux ('-widemux' only)
muxcover <internal options> ('-widemux' only)
opt -full
xilinx_srl -variable -minlen 3 (skip if '-nosrl')
techmap -map +/techmap.v -D LUT_SIZE=[46] [-map +/xilinx/mux_map.v] -map +/xilinx/arith_map.v
opt -fast
map_cells:
iopadmap -bits -outpad OBUF I:O -inpad IBUF O:I -toutpad OBUFT ~T:I:O -tinoutpad IOBUF ~T:O:I:IO A:top (skip if '-noiopad')
techmap -map +/techmap.v -map +/xilinx/cells_map.v
clean
map_ffs:
dfflegalize -cell $_DFFE_?P?P_ 01 -cell $_SDFFE_?P?P_ 01 -cell $_DLATCH_?P?_ 01 (for xc6v, xc7, xcu, xcup)
zinit -all w:* t:$_SDFFE_* ('-dff' only)
techmap -map +/xilinx/ff_map.v ('-abc9' only)
map_luts:
opt_expr -mux_undef -noclkinv
abc -luts 2:2,3,6:5[,10,20] [-dff] [-D 1] (option for '-nowidelut', '-dff', '-retime')
clean
techmap -map +/xilinx/ff_map.v (only if not '-abc9')
xilinx_srl -fixed -minlen 3 (skip if '-nosrl')
techmap -map +/xilinx/lut_map.v -map +/xilinx/cells_map.v -D LUT_WIDTH=[46]
xilinx_dffopt [-lut4]
opt_lut_ins -tech xilinx
finalize:
clkbufmap -buf BUFG O:I (skip if '-noclkbuf')
extractinv -inv INV O:I (only if '-ise')
clean
check:
hierarchy -check
stat -tech xilinx
check -noinit
blackbox =A:whitebox
edif:
write_edif -pvector bra
blif:
write_blif
\end{lstlisting}
\section{tcl -- execute a TCL script file}
\label{cmd:tcl}
\begin{lstlisting}[numbers=left,frame=single]
tcl <filename> [args]
This command executes the tcl commands in the specified file.
Use 'yosys cmd' to run the yosys command 'cmd' from tcl.
The tcl command 'yosys -import' can be used to import all yosys
commands directly as tcl commands to the tcl shell. Yosys commands
'proc' and 'rename' are wrapped to tcl commands 'procs' and 'renames'
in order to avoid a name collision with the built in commands.
If any arguments are specified, these arguments are provided to the script via
the standard $argc and $argv variables.
\end{lstlisting}
\section{techmap -- generic technology mapper}
\label{cmd:techmap}
\begin{lstlisting}[numbers=left,frame=single]
techmap [-map filename] [selection]
This pass implements a very simple technology mapper that replaces cells in
the design with implementations given in form of a Verilog or RTLIL source
file.
-map filename
the library of cell implementations to be used.
without this parameter a builtin library is used that
transforms the internal RTL cells to the internal gate
library.
-map %<design-name>
like -map above, but with an in-memory design instead of a file.
-extern
load the cell implementations as separate modules into the design
instead of inlining them.
-max_iter <number>
only run the specified number of iterations on each module.
default: unlimited
-recursive
instead of the iterative breadth-first algorithm use a recursive
depth-first algorithm. both methods should yield equivalent results,
but may differ in performance.
-autoproc
Automatically call "proc" on implementations that contain processes.
-wb
Ignore the 'whitebox' attribute on cell implementations.
-assert
this option will cause techmap to exit with an error if it can't map
a selected cell. only cell types that end on an underscore are accepted
as final cell types by this mode.
-D <define>, -I <incdir>
this options are passed as-is to the Verilog frontend for loading the
map file. Note that the Verilog frontend is also called with the
'-nooverwrite' option set.
When a module in the map file has the 'techmap_celltype' attribute set, it will
match cells with a type that match the text value of this attribute. Otherwise
the module name will be used to match the cell. Multiple space-separated cell
types can be listed, and wildcards using [] will be expanded (ie. "$_DFF_[PN]_"
is the same as "$_DFF_P_ $_DFF_N_").
When a module in the map file has the 'techmap_simplemap' attribute set, techmap
will use 'simplemap' (see 'help simplemap') to map cells matching the module.
When a module in the map file has the 'techmap_maccmap' attribute set, techmap
will use 'maccmap' (see 'help maccmap') to map cells matching the module.
When a module in the map file has the 'techmap_wrap' attribute set, techmap
will create a wrapper for the cell and then run the command string that the
attribute is set to on the wrapper module.
When a port on a module in the map file has the 'techmap_autopurge' attribute
set, and that port is not connected in the instantiation that is mapped, then
then a cell port connected only to such wires will be omitted in the mapped
version of the circuit.
All wires in the modules from the map file matching the pattern _TECHMAP_*
or *._TECHMAP_* are special wires that are used to pass instructions from
the mapping module to the techmap command. At the moment the following special
wires are supported:
_TECHMAP_FAIL_
When this wire is set to a non-zero constant value, techmap will not
use this module and instead try the next module with a matching
'techmap_celltype' attribute.
When such a wire exists but does not have a constant value after all
_TECHMAP_DO_* commands have been executed, an error is generated.
_TECHMAP_DO_*
This wires are evaluated in alphabetical order. The constant text value
of this wire is a yosys command (or sequence of commands) that is run
by techmap on the module. A common use case is to run 'proc' on modules
that are written using always-statements.
When such a wire has a non-constant value at the time it is to be
evaluated, an error is produced. That means it is possible for such a
wire to start out as non-constant and evaluate to a constant value
during processing of other _TECHMAP_DO_* commands.
A _TECHMAP_DO_* command may start with the special token 'CONSTMAP; '.
in this case techmap will create a copy for each distinct configuration
of constant inputs and shorted inputs at this point and import the
constant and connected bits into the map module. All further commands
are executed in this copy. This is a very convenient way of creating
optimized specializations of techmap modules without using the special
parameters described below.
A _TECHMAP_DO_* command may start with the special token 'RECURSION; '.
then techmap will recursively replace the cells in the module with their
implementation. This is not affected by the -max_iter option.
It is possible to combine both prefixes to 'RECURSION; CONSTMAP; '.
_TECHMAP_REMOVEINIT_<port-name>_
When this wire is set to a constant value, the init attribute of the wire(s)
connected to this port will be consumed. This wire must have the same
width as the given port, and for every bit that is set to 1 in the value,
the corresponding init attribute bit will be changed to 1'bx. If all
bits of an init attribute are left as x, it will be removed.
In addition to this special wires, techmap also supports special parameters in
modules in the map file:
_TECHMAP_CELLTYPE_
When a parameter with this name exists, it will be set to the type name
of the cell that matches the module.
_TECHMAP_CELLNAME_
When a parameter with this name exists, it will be set to the name
of the cell that matches the module.
_TECHMAP_CONSTMSK_<port-name>_
_TECHMAP_CONSTVAL_<port-name>_
When this pair of parameters is available in a module for a port, then
former has a 1-bit for each constant input bit and the latter has the
value for this bit. The unused bits of the latter are set to undef (x).
_TECHMAP_WIREINIT_<port-name>_
When a parameter with this name exists, it will be set to the initial
value of the wire(s) connected to the given port, as specified by the init
attribute. If the attribute doesn't exist, x will be filled for the
missing bits. To remove the init attribute bits used, use the
_TECHMAP_REMOVEINIT_*_ wires.
_TECHMAP_BITS_CONNMAP_
_TECHMAP_CONNMAP_<port-name>_
For an N-bit port, the _TECHMAP_CONNMAP_<port-name>_ parameter, if it
exists, will be set to an N*_TECHMAP_BITS_CONNMAP_ bit vector containing
N words (of _TECHMAP_BITS_CONNMAP_ bits each) that assign each single
bit driver a unique id. The values 0-3 are reserved for 0, 1, x, and z.
This can be used to detect shorted inputs.
When a module in the map file has a parameter where the according cell in the
design has a port, the module from the map file is only used if the port in
the design is connected to a constant value. The parameter is then set to the
constant value.
A cell with the name _TECHMAP_REPLACE_ in the map file will inherit the name
and attributes of the cell that is being replaced.
A cell with a name of the form `_TECHMAP_REPLACE_.<suffix>` in the map file will
be named thus but with the `_TECHMAP_REPLACE_' prefix substituted with the name
of the cell being replaced.
Similarly, a wire named in the form `_TECHMAP_REPLACE_.<suffix>` will cause a
new wire alias to be created and named as above but with the `_TECHMAP_REPLACE_'
prefix also substituted.
See 'help extract' for a pass that does the opposite thing.
See 'help flatten' for a pass that does flatten the design (which is
essentially techmap but using the design itself as map library).
\end{lstlisting}
\section{tee -- redirect command output to file}
\label{cmd:tee}
\begin{lstlisting}[numbers=left,frame=single]
tee [-q] [-o logfile|-a logfile] cmd
Execute the specified command, optionally writing the commands output to the
specified logfile(s).
-q
Do not print output to the normal destination (console and/or log file).
-o logfile
Write output to this file, truncate if exists.
-a logfile
Write output to this file, append if exists.
+INT, -INT
Add/subtract INT from the -v setting for this command.
\end{lstlisting}
\section{test\_abcloop -- automatically test handling of loops in abc command}
\label{cmd:test_abcloop}
\begin{lstlisting}[numbers=left,frame=single]
test_abcloop [options]
Test handling of logic loops in ABC.
-n {integer}
create this number of circuits and test them (default = 100).
-s {positive_integer}
use this value as rng seed value (default = unix time).
\end{lstlisting}
\section{test\_autotb -- generate simple test benches}
\label{cmd:test_autotb}
\begin{lstlisting}[numbers=left,frame=single]
test_autotb [options] [filename]
Automatically create primitive Verilog test benches for all modules in the
design. The generated testbenches toggle the input pins of the module in
a semi-random manner and dumps the resulting output signals.
This can be used to check the synthesis results for simple circuits by
comparing the testbench output for the input files and the synthesis results.
The backend automatically detects clock signals. Additionally a signal can
be forced to be interpreted as clock signal by setting the attribute
'gentb_clock' on the signal.
The attribute 'gentb_constant' can be used to force a signal to a constant
value after initialization. This can e.g. be used to force a reset signal
low in order to explore more inner states in a state machine.
The attribute 'gentb_skip' can be attached to modules to suppress testbench
generation.
-n <int>
number of iterations the test bench should run (default = 1000)
-seed <int>
seed used for pseudo-random number generation (default = 0).
a value of 0 will cause an arbitrary seed to be chosen, based on
the current system time.
\end{lstlisting}
\section{test\_cell -- automatically test the implementation of a cell type}
\label{cmd:test_cell}
\begin{lstlisting}[numbers=left,frame=single]
test_cell [options] {cell-types}
Tests the internal implementation of the given cell type (for example '$add')
by comparing SAT solver, EVAL and TECHMAP implementations of the cell types..
Run with 'all' instead of a cell type to run the test on all supported
cell types. Use for example 'all /$add' for all cell types except $add.
-n {integer}
create this number of cell instances and test them (default = 100).
-s {positive_integer}
use this value as rng seed value (default = unix time).
-f {rtlil_file}
don't generate circuits. instead load the specified RTLIL file.
-w {filename_prefix}
don't test anything. just generate the circuits and write them
to RTLIL files with the specified prefix
-map {filename}
pass this option to techmap.
-simlib
use "techmap -D SIMLIB_NOCHECKS -map +/simlib.v -max_iter 2 -autoproc"
-aigmap
instead of calling "techmap", call "aigmap"
-muxdiv
when creating test benches with dividers, create an additional mux
to mask out the division-by-zero case
-script {script_file}
instead of calling "techmap", call "script {script_file}".
-const
set some input bits to random constant values
-nosat
do not check SAT model or run SAT equivalence checking
-noeval
do not check const-eval models
-edges
test cell edges db creator against sat-based implementation
-v
print additional debug information to the console
-vlog {filename}
create a Verilog test bench to test simlib and write_verilog
\end{lstlisting}
\section{test\_pmgen -- test pass for pmgen}
\label{cmd:test_pmgen}
\begin{lstlisting}[numbers=left,frame=single]
test_pmgen -reduce_chain [options] [selection]
Demo for recursive pmgen patterns. Map chains of AND/OR/XOR to $reduce_*.
test_pmgen -reduce_tree [options] [selection]
Demo for recursive pmgen patterns. Map trees of AND/OR/XOR to $reduce_*.
test_pmgen -eqpmux [options] [selection]
Demo for recursive pmgen patterns. Optimize EQ/NE/PMUX circuits.
test_pmgen -generate [options] <pattern_name>
Create modules that match the specified pattern.
\end{lstlisting}
\section{torder -- print cells in topological order}
\label{cmd:torder}
\begin{lstlisting}[numbers=left,frame=single]
torder [options] [selection]
This command prints the selected cells in topological order.
-stop <cell_type> <cell_port>
do not use the specified cell port in topological sorting
-noautostop
by default Q outputs of internal FF cells and memory read port outputs
are not used in topological sorting. this option deactivates that.
\end{lstlisting}
\section{trace -- redirect command output to file}
\label{cmd:trace}
\begin{lstlisting}[numbers=left,frame=single]
trace cmd
Execute the specified command, logging all changes the command performs on
the design in real time.
\end{lstlisting}
\section{tribuf -- infer tri-state buffers}
\label{cmd:tribuf}
\begin{lstlisting}[numbers=left,frame=single]
tribuf [options] [selection]
This pass transforms $mux cells with 'z' inputs to tristate buffers.
-merge
merge multiple tri-state buffers driving the same net
into a single buffer.
-logic
convert tri-state buffers that do not drive output ports
to non-tristate logic. this option implies -merge.
\end{lstlisting}
\section{uniquify -- create unique copies of modules}
\label{cmd:uniquify}
\begin{lstlisting}[numbers=left,frame=single]
uniquify [selection]
By default, a module that is instantiated by several other modules is only
kept once in the design. This preserves the original modularity of the design
and reduces the overall size of the design in memory. But it prevents certain
optimizations and other operations on the design. This pass creates unique
modules for all selected cells. The created modules are marked with the
'unique' attribute.
This commands only operates on modules that by themself have the 'unique'
attribute set (the 'top' module is unique implicitly).
\end{lstlisting}
\section{verific -- load Verilog and VHDL designs using Verific}
\label{cmd:verific}
\begin{lstlisting}[numbers=left,frame=single]
verific {-vlog95|-vlog2k|-sv2005|-sv2009|-sv2012|-sv} <verilog-file>..
Load the specified Verilog/SystemVerilog files into Verific.
All files specified in one call to this command are one compilation unit.
Files passed to different calls to this command are treated as belonging to
different compilation units.
Additional -D<macro>[=<value>] options may be added after the option indicating
the language version (and before file names) to set additional verilog defines.
The macros YOSYS, SYNTHESIS, and VERIFIC are defined implicitly.
verific -formal <verilog-file>..
Like -sv, but define FORMAL instead of SYNTHESIS.
verific {-vhdl87|-vhdl93|-vhdl2k|-vhdl2008|-vhdl} <vhdl-file>..
Load the specified VHDL files into Verific.
verific {-f|-F} <command-file>
Load and execute the specified command file.
Command file parser supports following commands:
+define - defines macro
-u - upper case all identifier (makes Verilog parser case insensitive)
-v - register library name (file)
-y - register library name (directory)
+incdir - specify include dir
+libext - specify library extension
+liborder - add library in ordered list
+librescan - unresolved modules will be always searched starting with the first
library specified by -y/-v options.
-f/-file - nested -f option
-F - nested -F option
parse mode:
-ams
+systemverilogext
+v2k
+verilog1995ext
+verilog2001ext
-sverilog
verific [-work <libname>] {-sv|-vhdl|...} <hdl-file>
Load the specified Verilog/SystemVerilog/VHDL file into the specified library.
(default library when -work is not present: "work")
verific [-L <libname>] {-sv|-vhdl|...} <hdl-file>
Look up external definitions in the specified library.
(-L may be used more than once)
verific -vlog-incdir <directory>..
Add Verilog include directories.
verific -vlog-libdir <directory>..
Add Verilog library directories. Verific will search in this directories to
find undefined modules.
verific -vlog-define <macro>[=<value>]..
Add Verilog defines.
verific -vlog-undef <macro>..
Remove Verilog defines previously set with -vlog-define.
verific -set-error <msg_id>..
verific -set-warning <msg_id>..
verific -set-info <msg_id>..
verific -set-ignore <msg_id>..
Set message severity. <msg_id> is the string in square brackets when a message
is printed, such as VERI-1209.
verific -import [options] <top-module>..
Elaborate the design for the specified top modules, import to Yosys and
reset the internal state of Verific.
Import options:
-all
Elaborate all modules, not just the hierarchy below the given top
modules. With this option the list of modules to import is optional.
-gates
Create a gate-level netlist.
-flatten
Flatten the design in Verific before importing.
-extnets
Resolve references to external nets by adding module ports as needed.
-autocover
Generate automatic cover statements for all asserts
-fullinit
Keep all register initializations, even those for non-FF registers.
-chparam name value
Elaborate the specified top modules (all modules when -all given) using
this parameter value. Modules on which this parameter does not exist will
cause Verific to produce a VERI-1928 or VHDL-1676 message. This option
can be specified multiple times to override multiple parameters.
String values must be passed in double quotes (").
-v, -vv
Verbose log messages. (-vv is even more verbose than -v.)
The following additional import options are useful for debugging the Verific
bindings (for Yosys and/or Verific developers):
-k
Keep going after an unsupported verific primitive is found. The
unsupported primitive is added as blockbox module to the design.
This will also add all SVA related cells to the design parallel to
the checker logic inferred by it.
-V
Import Verific netlist as-is without translating to Yosys cell types.
-nosva
Ignore SVA properties, do not infer checker logic.
-L <int>
Maximum number of ctrl bits for SVA checker FSMs (default=16).
-n
Keep all Verific names on instances and nets. By default only
user-declared names are preserved.
-d <dump_file>
Dump the Verific netlist as a verilog file.
verific [-work <libname>] -pp [options] <filename> [<module>]..
Pretty print design (or just module) to the specified file from the
specified library. (default library when -work is not present: "work")
Pretty print options:
-verilog
Save output for Verilog/SystemVerilog design modules (default).
-vhdl
Save output for VHDL design units.
verific -app <application>..
Execute YosysHQ formal application on loaded Verilog files.
Application options:
-module <module>
Run formal application only on specified module.
-blacklist <filename[:lineno]>
Do not run application on modules from files that match the filename
or filename and line number if provided in such format.
Parameter can also contain comma separated list of file locations.
-blfile <file>
Do not run application on locations specified in file, they can represent filename
or filename and location in file.
Applications:
WARNING: Applications only available in commercial build.
verific -template <name> <top_module>..
Generate template for specified top module of loaded design.
Template options:
-out
Specifies output file for generated template, by default output is stdout
-chparam name value
Generate template using this parameter value. Otherwise default parameter
values will be used for templat generate functionality. This option
can be specified multiple times to override multiple parameters.
String values must be passed in double quotes (").
Templates:
WARNING: Templates only available in commercial build.
verific -cfg [<name> [<value>]]
Get/set Verific runtime flags.
Use YosysHQ Tabby CAD Suite if you need Yosys+Verific.
https://www.yosyshq.com/
Contact office@yosyshq.com for free evaluation
binaries of YosysHQ Tabby CAD Suite.
\end{lstlisting}
\section{verilog\_defaults -- set default options for read\_verilog}
\label{cmd:verilog_defaults}
\begin{lstlisting}[numbers=left,frame=single]
verilog_defaults -add [options]
Add the specified options to the list of default options to read_verilog.
verilog_defaults -clear
Clear the list of Verilog default options.
verilog_defaults -push
verilog_defaults -pop
Push or pop the list of default options to a stack. Note that -push does
not imply -clear.
\end{lstlisting}
\section{verilog\_defines -- define and undefine verilog defines}
\label{cmd:verilog_defines}
\begin{lstlisting}[numbers=left,frame=single]
verilog_defines [options]
Define and undefine verilog preprocessor macros.
-Dname[=definition]
define the preprocessor symbol 'name' and set its optional value
'definition'
-Uname[=definition]
undefine the preprocessor symbol 'name'
-reset
clear list of defined preprocessor symbols
-list
list currently defined preprocessor symbols
\end{lstlisting}
\section{wbflip -- flip the whitebox attribute}
\label{cmd:wbflip}
\begin{lstlisting}[numbers=left,frame=single]
wbflip [selection]
Flip the whitebox attribute on selected cells. I.e. if it's set, unset it, and
vice-versa. Blackbox cells are not effected by this command.
\end{lstlisting}
\section{wreduce -- reduce the word size of operations if possible}
\label{cmd:wreduce}
\begin{lstlisting}[numbers=left,frame=single]
wreduce [options] [selection]
This command reduces the word size of operations. For example it will replace
the 32 bit adders in the following code with adders of more appropriate widths:
module test(input [3:0] a, b, c, output [7:0] y);
assign y = a + b + c + 1;
endmodule
Options:
-memx
Do not change the width of memory address ports. Use this options in
flows that use the 'memory_memx' pass.
-keepdc
Do not optimize explicit don't-care values.
\end{lstlisting}
\section{write\_aiger -- write design to AIGER file}
\label{cmd:write_aiger}
\begin{lstlisting}[numbers=left,frame=single]
write_aiger [options] [filename]
Write the current design to an AIGER file. The design must be flattened and
must not contain any cell types except $_AND_, $_NOT_, simple FF types,
$assert and $assume cells, and $initstate cells.
$assert and $assume cells are converted to AIGER bad state properties and
invariant constraints.
-ascii
write ASCII version of AIGER format
-zinit
convert FFs to zero-initialized FFs, adding additional inputs for
uninitialized FFs.
-miter
design outputs are AIGER bad state properties
-symbols
include a symbol table in the generated AIGER file
-map <filename>
write an extra file with port and latch symbols
-vmap <filename>
like -map, but more verbose
-I, -O, -B, -L
If the design contains no input/output/assert/flip-flop then create one
dummy input/output/bad_state-pin or latch to make the tools reading the
AIGER file happy.
\end{lstlisting}
\section{write\_blif -- write design to BLIF file}
\label{cmd:write_blif}
\begin{lstlisting}[numbers=left,frame=single]
write_blif [options] [filename]
Write the current design to an BLIF file.
-top top_module
set the specified module as design top module
-buf <cell-type> <in-port> <out-port>
use cells of type <cell-type> with the specified port names for buffers
-unbuf <cell-type> <in-port> <out-port>
replace buffer cells with the specified name and port names with
a .names statement that models a buffer
-true <cell-type> <out-port>
-false <cell-type> <out-port>
-undef <cell-type> <out-port>
use the specified cell types to drive nets that are constant 1, 0, or
undefined. when '-' is used as <cell-type>, then <out-port> specifies
the wire name to be used for the constant signal and no cell driving
that wire is generated. when '+' is used as <cell-type>, then <out-port>
specifies the wire name to be used for the constant signal and a .names
statement is generated to drive the wire.
-noalias
if a net name is aliasing another net name, then by default a net
without fanout is created that is driven by the other net. This option
suppresses the generation of this nets without fanout.
The following options can be useful when the generated file is not going to be
read by a BLIF parser but a custom tool. It is recommended to not name the output
file *.blif when any of this options is used.
-icells
do not translate Yosys's internal gates to generic BLIF logic
functions. Instead create .subckt or .gate lines for all cells.
-gates
print .gate instead of .subckt lines for all cells that are not
instantiations of other modules from this design.
-conn
do not generate buffers for connected wires. instead use the
non-standard .conn statement.
-attr
use the non-standard .attr statement to write cell attributes
-param
use the non-standard .param statement to write cell parameters
-cname
use the non-standard .cname statement to write cell names
-iname, -iattr
enable -cname and -attr functionality for .names statements
(the .cname and .attr statements will be included in the BLIF
output after the truth table for the .names statement)
-blackbox
write blackbox cells with .blackbox statement.
-impltf
do not write definitions for the $true, $false and $undef wires.
\end{lstlisting}
\section{write\_btor -- write design to BTOR file}
\label{cmd:write_btor}
\begin{lstlisting}[numbers=left,frame=single]
write_btor [options] [filename]
Write a BTOR description of the current design.
-v
Add comments and indentation to BTOR output file
-s
Output only a single bad property for all asserts
-c
Output cover properties using 'bad' statements instead of asserts
-i <filename>
Create additional info file with auxiliary information
-x
Output symbols for internal netnames (starting with '$')
\end{lstlisting}
\section{write\_cxxrtl -- convert design to C++ RTL simulation}
\label{cmd:write_cxxrtl}
\begin{lstlisting}[numbers=left,frame=single]
write_cxxrtl [options] [filename]
Write C++ code that simulates the design. The generated code requires a driver
that instantiates the design, toggles its clock, and interacts with its ports.
The following driver may be used as an example for a design with a single clock
driving rising edge triggered flip-flops:
#include "top.cc"
int main() {
cxxrtl_design::p_top top;
top.step();
while (1) {
/* user logic */
top.p_clk.set(false);
top.step();
top.p_clk.set(true);
top.step();
}
}
Note that CXXRTL simulations, just like the hardware they are simulating, are
subject to race conditions. If, in the example above, the user logic would run
simultaneously with the rising edge of the clock, the design would malfunction.
This backend supports replacing parts of the design with black boxes implemented
in C++. If a module marked as a CXXRTL black box, its implementation is ignored,
and the generated code consists only of an interface and a factory function.
The driver must implement the factory function that creates an implementation of
the black box, taking into account the parameters it is instantiated with.
For example, the following Verilog code defines a CXXRTL black box interface for
a synchronous debug sink:
(* cxxrtl_blackbox *)
module debug(...);
(* cxxrtl_edge = "p" *) input clk;
input en;
input [7:0] i_data;
(* cxxrtl_sync *) output [7:0] o_data;
endmodule
For this HDL interface, this backend will generate the following C++ interface:
struct bb_p_debug : public module {
value<1> p_clk;
bool posedge_p_clk() const { /* ... */ }
value<1> p_en;
value<8> p_i_data;
wire<8> p_o_data;
bool eval() override;
bool commit() override;
static std::unique_ptr<bb_p_debug>
create(std::string name, metadata_map parameters, metadata_map attributes);
};
The `create' function must be implemented by the driver. For example, it could
always provide an implementation logging the values to standard error stream:
namespace cxxrtl_design {
struct stderr_debug : public bb_p_debug {
bool eval() override {
if (posedge_p_clk() && p_en)
fprintf(stderr, "debug: %02x\n", p_i_data.data[0]);
p_o_data.next = p_i_data;
return bb_p_debug::eval();
}
};
std::unique_ptr<bb_p_debug>
bb_p_debug::create(std::string name, cxxrtl::metadata_map parameters,
cxxrtl::metadata_map attributes) {
return std::make_unique<stderr_debug>();
}
}
For complex applications of black boxes, it is possible to parameterize their
port widths. For example, the following Verilog code defines a CXXRTL black box
interface for a configurable width debug sink:
(* cxxrtl_blackbox, cxxrtl_template = "WIDTH" *)
module debug(...);
parameter WIDTH = 8;
(* cxxrtl_edge = "p" *) input clk;
input en;
(* cxxrtl_width = "WIDTH" *) input [WIDTH - 1:0] i_data;
(* cxxrtl_width = "WIDTH" *) output [WIDTH - 1:0] o_data;
endmodule
For this parametric HDL interface, this backend will generate the following C++
interface (only the differences are shown):
template<size_t WIDTH>
struct bb_p_debug : public module {
// ...
value<WIDTH> p_i_data;
wire<WIDTH> p_o_data;
// ...
static std::unique_ptr<bb_p_debug<WIDTH>>
create(std::string name, metadata_map parameters, metadata_map attributes);
};
The `create' function must be implemented by the driver, specialized for every
possible combination of template parameters. (Specialization is necessary to
enable separate compilation of generated code and black box implementations.)
template<size_t SIZE>
struct stderr_debug : public bb_p_debug<SIZE> {
// ...
};
template<>
std::unique_ptr<bb_p_debug<8>>
bb_p_debug<8>::create(std::string name, cxxrtl::metadata_map parameters,
cxxrtl::metadata_map attributes) {
return std::make_unique<stderr_debug<8>>();
}
The following attributes are recognized by this backend:
cxxrtl_blackbox
only valid on modules. if specified, the module contents are ignored,
and the generated code includes only the module interface and a factory
function, which will be called to instantiate the module.
cxxrtl_edge
only valid on inputs of black boxes. must be one of "p", "n", "a".
if specified on signal `clk`, the generated code includes edge detectors
`posedge_p_clk()` (if "p"), `negedge_p_clk()` (if "n"), or both (if
"a"), simplifying implementation of clocked black boxes.
cxxrtl_template
only valid on black boxes. must contain a space separated sequence of
identifiers that have a corresponding black box parameters. for each
of them, the generated code includes a `size_t` template parameter.
cxxrtl_width
only valid on ports of black boxes. must be a constant expression, which
is directly inserted into generated code.
cxxrtl_comb, cxxrtl_sync
only valid on outputs of black boxes. if specified, indicates that every
bit of the output port is driven, correspondingly, by combinatorial or
synchronous logic. this knowledge is used for scheduling optimizations.
if neither is specified, the output will be pessimistically treated as
driven by both combinatorial and synchronous logic.
The following options are supported by this backend:
-print-wire-types, -print-debug-wire-types
enable additional debug logging, for pass developers.
-header
generate separate interface (.h) and implementation (.cc) files.
if specified, the backend must be called with a filename, and filename
of the interface is derived from filename of the implementation.
otherwise, interface and implementation are generated together.
-namespace <ns-name>
place the generated code into namespace <ns-name>. if not specified,
"cxxrtl_design" is used.
-nohierarchy
use design hierarchy as-is. in most designs, a top module should be
present as it is exposed through the C API and has unbuffered outputs
for improved performance; it will be determined automatically if absent.
-noflatten
don't flatten the design. fully flattened designs can evaluate within
one delta cycle if they have no combinatorial feedback.
note that the debug interface and waveform dumps use full hierarchical
names for all wires even in flattened designs.
-noproc
don't convert processes to netlists. in most designs, converting
processes significantly improves evaluation performance at the cost of
slight increase in compilation time.
-O <level>
set the optimization level. the default is -O6. higher optimization
levels dramatically decrease compile and run time, and highest level
possible for a design should be used.
-O0
no optimization.
-O1
unbuffer internal wires if possible.
-O2
like -O1, and localize internal wires if possible.
-O3
like -O2, and inline internal wires if possible.
-O4
like -O3, and unbuffer public wires not marked (*keep*) if possible.
-O5
like -O4, and localize public wires not marked (*keep*) if possible.
-O6
like -O5, and inline public wires not marked (*keep*) if possible.
-g <level>
set the debug level. the default is -g4. higher debug levels provide
more visibility and generate more code, but do not pessimize evaluation.
-g0
no debug information. the C API is disabled.
-g1
include bare minimum of debug information necessary to access all design
state. the C API is enabled.
-g2
like -g1, but include debug information for all public wires that are
directly accessible through the C++ interface.
-g3
like -g2, and include debug information for public wires that are tied
to a constant or another public wire.
-g4
like -g3, and compute debug information on demand for all public wires
that were optimized out.
\end{lstlisting}
\section{write\_edif -- write design to EDIF netlist file}
\label{cmd:write_edif}
\begin{lstlisting}[numbers=left,frame=single]
write_edif [options] [filename]
Write the current design to an EDIF netlist file.
-top top_module
set the specified module as design top module
-nogndvcc
do not create "GND" and "VCC" cells. (this will produce an error
if the design contains constant nets. use "hilomap" to map to custom
constant drivers first)
-gndvccy
create "GND" and "VCC" cells with "Y" outputs. (the default is "G"
for "GND" and "P" for "VCC".)
-attrprop
create EDIF properties for cell attributes
-keep
create extra KEEP nets by allowing a cell to drive multiple nets.
-pvector {par|bra|ang}
sets the delimiting character for module port rename clauses to
parentheses, square brackets, or angle brackets.
Unfortunately there are different "flavors" of the EDIF file format. This
command generates EDIF files for the Xilinx place&route tools. It might be
necessary to make small modifications to this command when a different tool
is targeted.
\end{lstlisting}
\section{write\_file -- write a text to a file}
\label{cmd:write_file}
\begin{lstlisting}[numbers=left,frame=single]
write_file [options] output_file [input_file]
Write the text from the input file to the output file.
-a
Append to output file (instead of overwriting)
Inside a script the input file can also can a here-document:
write_file hello.txt <<EOT
Hello World!
EOT
\end{lstlisting}
\section{write\_firrtl -- write design to a FIRRTL file}
\label{cmd:write_firrtl}
\begin{lstlisting}[numbers=left,frame=single]
write_firrtl [options] [filename]
Write a FIRRTL netlist of the current design.
The following commands are executed by this command:
pmuxtree
\end{lstlisting}
\section{write\_ilang -- (deprecated) alias of write\_rtlil}
\label{cmd:write_ilang}
\begin{lstlisting}[numbers=left,frame=single]
See `help write_rtlil`.
\end{lstlisting}
\section{write\_intersynth -- write design to InterSynth netlist file}
\label{cmd:write_intersynth}
\begin{lstlisting}[numbers=left,frame=single]
write_intersynth [options] [filename]
Write the current design to an 'intersynth' netlist file. InterSynth is
a tool for Coarse-Grain Example-Driven Interconnect Synthesis.
-notypes
do not generate celltypes and conntypes commands. i.e. just output
the netlists. this is used for postsilicon synthesis.
-lib <verilog_or_rtlil_file>
Use the specified library file for determining whether cell ports are
inputs or outputs. This option can be used multiple times to specify
more than one library.
-selected
only write selected modules. modules must be selected entirely or
not at all.
http://bygone.clairexen.net/intersynth/
\end{lstlisting}
\section{write\_json -- write design to a JSON file}
\label{cmd:write_json}
\begin{lstlisting}[numbers=left,frame=single]
write_json [options] [filename]
Write a JSON netlist of the current design.
-aig
include AIG models for the different gate types
-compat-int
emit 32-bit or smaller fully-defined parameter values directly
as JSON numbers (for compatibility with old parsers)
The general syntax of the JSON output created by this command is as follows:
{
"creator": "Yosys <version info>",
"modules": {
<module_name>: {
"attributes": {
<attribute_name>: <attribute_value>,
...
},
"parameter_default_values": {
<parameter_name>: <parameter_value>,
...
},
"ports": {
<port_name>: <port_details>,
...
},
"cells": {
<cell_name>: <cell_details>,
...
},
"memories": {
<memory_name>: <memory_details>,
...
},
"netnames": {
<net_name>: <net_details>,
...
}
}
},
"models": {
...
},
}
Where <port_details> is:
{
"direction": <"input" | "output" | "inout">,
"bits": <bit_vector>
"offset": <the lowest bit index in use, if non-0>
"upto": <1 if the port bit indexing is MSB-first>
}
The "offset" and "upto" fields are skipped if their value would be 0.They don't affect connection semantics, and are only used to preserve originalHDL bit indexing.And <cell_details> is:
{
"hide_name": <1 | 0>,
"type": <cell_type>,
"model": <AIG model name, if -aig option used>,
"parameters": {
<parameter_name>: <parameter_value>,
...
},
"attributes": {
<attribute_name>: <attribute_value>,
...
},
"port_directions": {
<port_name>: <"input" | "output" | "inout">,
...
},
"connections": {
<port_name>: <bit_vector>,
...
},
}
And <memory_details> is:
{
"hide_name": <1 | 0>,
"attributes": {
<attribute_name>: <attribute_value>,
...
},
"width": <memory width>
"start_offset": <the lowest valid memory address>
"size": <memory size>
}
And <net_details> is:
{
"hide_name": <1 | 0>,
"bits": <bit_vector>
"offset": <the lowest bit index in use, if non-0>
"upto": <1 if the port bit indexing is MSB-first>
}
The "hide_name" fields are set to 1 when the name of this cell or net is
automatically created and is likely not of interest for a regular user.
The "port_directions" section is only included for cells for which the
interface is known.
Module and cell ports and nets can be single bit wide or vectors of multiple
bits. Each individual signal bit is assigned a unique integer. The <bit_vector>
values referenced above are vectors of this integers. Signal bits that are
connected to a constant driver are denoted as string "0", "1", "x", or
"z" instead of a number.
Bit vectors (including integers) are written as string holding the binaryrepresentation of the value. Strings are written as strings, with an appendedblank in cases of strings of the form /[01xz]* */.
For example the following Verilog code:
module test(input x, y);
(* keep *) foo #(.P(42), .Q(1337))
foo_inst (.A({x, y}), .B({y, x}), .C({4'd10, {4{x}}}));
endmodule
Translates to the following JSON output:
{
"creator": "Yosys 0.9+2406 (git sha1 fb1168d8, clang 9.0.1 -fPIC -Os)",
"modules": {
"test": {
"attributes": {
"cells_not_processed": "00000000000000000000000000000001",
"src": "test.v:1.1-4.10"
},
"ports": {
"x": {
"direction": "input",
"bits": [ 2 ]
},
"y": {
"direction": "input",
"bits": [ 3 ]
}
},
"cells": {
"foo_inst": {
"hide_name": 0,
"type": "foo",
"parameters": {
"P": "00000000000000000000000000101010",
"Q": "00000000000000000000010100111001"
},
"attributes": {
"keep": "00000000000000000000000000000001",
"module_not_derived": "00000000000000000000000000000001",
"src": "test.v:3.1-3.55"
},
"connections": {
"A": [ 3, 2 ],
"B": [ 2, 3 ],
"C": [ 2, 2, 2, 2, "0", "1", "0", "1" ]
}
}
},
"netnames": {
"x": {
"hide_name": 0,
"bits": [ 2 ],
"attributes": {
"src": "test.v:1.19-1.20"
}
},
"y": {
"hide_name": 0,
"bits": [ 3 ],
"attributes": {
"src": "test.v:1.22-1.23"
}
}
}
}
}
}
The models are given as And-Inverter-Graphs (AIGs) in the following form:
"models": {
<model_name>: [
/* 0 */ [ <node-spec> ],
/* 1 */ [ <node-spec> ],
/* 2 */ [ <node-spec> ],
...
],
...
},
The following node-types may be used:
[ "port", <portname>, <bitindex>, <out-list> ]
- the value of the specified input port bit
[ "nport", <portname>, <bitindex>, <out-list> ]
- the inverted value of the specified input port bit
[ "and", <node-index>, <node-index>, <out-list> ]
- the ANDed value of the specified nodes
[ "nand", <node-index>, <node-index>, <out-list> ]
- the inverted ANDed value of the specified nodes
[ "true", <out-list> ]
- the constant value 1
[ "false", <out-list> ]
- the constant value 0
All nodes appear in topological order. I.e. only nodes with smaller indices
are referenced by "and" and "nand" nodes.
The optional <out-list> at the end of a node specification is a list of
output portname and bitindex pairs, specifying the outputs driven by this node.
For example, the following is the model for a 3-input 3-output $reduce_and cell
inferred by the following code:
module test(input [2:0] in, output [2:0] out);
assign in = &out;
endmodule
"$reduce_and:3U:3": [
/* 0 */ [ "port", "A", 0 ],
/* 1 */ [ "port", "A", 1 ],
/* 2 */ [ "and", 0, 1 ],
/* 3 */ [ "port", "A", 2 ],
/* 4 */ [ "and", 2, 3, "Y", 0 ],
/* 5 */ [ "false", "Y", 1, "Y", 2 ]
]
Future version of Yosys might add support for additional fields in the JSON
format. A program processing this format must ignore all unknown fields.
\end{lstlisting}
\section{write\_rtlil -- write design to RTLIL file}
\label{cmd:write_rtlil}
\begin{lstlisting}[numbers=left,frame=single]
write_rtlil [filename]
Write the current design to an RTLIL file. (RTLIL is a text representation
of a design in yosys's internal format.)
-selected
only write selected parts of the design.
\end{lstlisting}
\section{write\_simplec -- convert design to simple C code}
\label{cmd:write_simplec}
\begin{lstlisting}[numbers=left,frame=single]
write_simplec [options] [filename]
Write simple C code for simulating the design. The C code written can be used to
simulate the design in a C environment, but the purpose of this command is to
generate code that works well with C-based formal verification.
-verbose
this will print the recursive walk used to export the modules.
-i8, -i16, -i32, -i64
set the maximum integer bit width to use in the generated code.
THIS COMMAND IS UNDER CONSTRUCTION
\end{lstlisting}
\section{write\_smt2 -- write design to SMT-LIBv2 file}
\label{cmd:write_smt2}
\begin{lstlisting}[numbers=left,frame=single]
write_smt2 [options] [filename]
Write a SMT-LIBv2 [1] description of the current design. For a module with name
'<mod>' this will declare the sort '<mod>_s' (state of the module) and will
define and declare functions operating on that state.
The following SMT2 functions are generated for a module with name '<mod>'.
Some declarations/definitions are printed with a special comment. A prover
using the SMT2 files can use those comments to collect all relevant metadata
about the design.
; yosys-smt2-module <mod>
(declare-sort |<mod>_s| 0)
The sort representing a state of module <mod>.
(define-fun |<mod>_h| ((state |<mod>_s|)) Bool (...))
This function must be asserted for each state to establish the
design hierarchy.
; yosys-smt2-input <wirename> <width>
; yosys-smt2-output <wirename> <width>
; yosys-smt2-register <wirename> <width>
; yosys-smt2-wire <wirename> <width>
(define-fun |<mod>_n <wirename>| (|<mod>_s|) (_ BitVec <width>))
(define-fun |<mod>_n <wirename>| (|<mod>_s|) Bool)
For each port, register, and wire with the 'keep' attribute set an
accessor function is generated. Single-bit wires are returned as Bool,
multi-bit wires as BitVec.
; yosys-smt2-cell <submod> <instancename>
(declare-fun |<mod>_h <instancename>| (|<mod>_s|) |<submod>_s|)
There is a function like that for each hierarchical instance. It
returns the sort that represents the state of the sub-module that
implements the instance.
(declare-fun |<mod>_is| (|<mod>_s|) Bool)
This function must be asserted 'true' for initial states, and 'false'
otherwise.
(define-fun |<mod>_i| ((state |<mod>_s|)) Bool (...))
This function must be asserted 'true' for initial states. For
non-initial states it must be left unconstrained.
(define-fun |<mod>_t| ((state |<mod>_s|) (next_state |<mod>_s|)) Bool (...))
This function evaluates to 'true' if the states 'state' and
'next_state' form a valid state transition.
(define-fun |<mod>_a| ((state |<mod>_s|)) Bool (...))
This function evaluates to 'true' if all assertions hold in the state.
(define-fun |<mod>_u| ((state |<mod>_s|)) Bool (...))
This function evaluates to 'true' if all assumptions hold in the state.
; yosys-smt2-assert <id> <filename:linenum>
(define-fun |<mod>_a <id>| ((state |<mod>_s|)) Bool (...))
Each $assert cell is converted into one of this functions. The function
evaluates to 'true' if the assert statement holds in the state.
; yosys-smt2-assume <id> <filename:linenum>
(define-fun |<mod>_u <id>| ((state |<mod>_s|)) Bool (...))
Each $assume cell is converted into one of this functions. The function
evaluates to 'true' if the assume statement holds in the state.
; yosys-smt2-cover <id> <filename:linenum>
(define-fun |<mod>_c <id>| ((state |<mod>_s|)) Bool (...))
Each $cover cell is converted into one of this functions. The function
evaluates to 'true' if the cover statement is activated in the state.
Options:
-verbose
this will print the recursive walk used to export the modules.
-stbv
Use a BitVec sort to represent a state instead of an uninterpreted
sort. As a side-effect this will prevent use of arrays to model
memories.
-stdt
Use SMT-LIB 2.6 style datatypes to represent a state instead of an
uninterpreted sort.
-nobv
disable support for BitVec (FixedSizeBitVectors theory). without this
option multi-bit wires are represented using the BitVec sort and
support for coarse grain cells (incl. arithmetic) is enabled.
-nomem
disable support for memories (via ArraysEx theory). this option is
implied by -nobv. only $mem cells without merged registers in
read ports are supported. call "memory" with -nordff to make sure
that no registers are merged into $mem read ports. '<mod>_m' functions
will be generated for accessing the arrays that are used to represent
memories.
-wires
create '<mod>_n' functions for all public wires. by default only ports,
registers, and wires with the 'keep' attribute are exported.
-tpl <template_file>
use the given template file. the line containing only the token '%%'
is replaced with the regular output of this command.
-solver-option <option> <value>
emit a `; yosys-smt2-solver-option` directive for yosys-smtbmc to write
the given option as a `(set-option ...)` command in the SMT-LIBv2.
[1] For more information on SMT-LIBv2 visit http://smt-lib.org/ or read David
R. Cok's tutorial: https://smtlib.github.io/jSMTLIB/SMTLIBTutorial.pdf
---------------------------------------------------------------------------
Example:
Consider the following module (test.v). We want to prove that the output can
never transition from a non-zero value to a zero value.
module test(input clk, output reg [3:0] y);
always @(posedge clk)
y <= (y << 1) | ^y;
endmodule
For this proof we create the following template (test.tpl).
; we need QF_UFBV for this proof
(set-logic QF_UFBV)
; insert the auto-generated code here
%%
; declare two state variables s1 and s2
(declare-fun s1 () test_s)
(declare-fun s2 () test_s)
; state s2 is the successor of state s1
(assert (test_t s1 s2))
; we are looking for a model with y non-zero in s1
(assert (distinct (|test_n y| s1) #b0000))
; we are looking for a model with y zero in s2
(assert (= (|test_n y| s2) #b0000))
; is there such a model?
(check-sat)
The following yosys script will create a 'test.smt2' file for our proof:
read_verilog test.v
hierarchy -check; proc; opt; check -assert
write_smt2 -bv -tpl test.tpl test.smt2
Running 'cvc4 test.smt2' will print 'unsat' because y can never transition
from non-zero to zero in the test design.
\end{lstlisting}
\section{write\_smv -- write design to SMV file}
\label{cmd:write_smv}
\begin{lstlisting}[numbers=left,frame=single]
write_smv [options] [filename]
Write an SMV description of the current design.
-verbose
this will print the recursive walk used to export the modules.
-tpl <template_file>
use the given template file. the line containing only the token '%%'
is replaced with the regular output of this command.
THIS COMMAND IS UNDER CONSTRUCTION
\end{lstlisting}
\section{write\_spice -- write design to SPICE netlist file}
\label{cmd:write_spice}
\begin{lstlisting}[numbers=left,frame=single]
write_spice [options] [filename]
Write the current design to an SPICE netlist file.
-big_endian
generate multi-bit ports in MSB first order
(default is LSB first)
-neg net_name
set the net name for constant 0 (default: Vss)
-pos net_name
set the net name for constant 1 (default: Vdd)
-buf DC|subckt_name
set the name for jumper element (default: DC)
(used to connect different nets)
-nc_prefix
prefix for not-connected nets (default: _NC)
-inames
include names of internal ($-prefixed) nets in outputs
(default is to use net numbers instead)
-top top_module
set the specified module as design top module
\end{lstlisting}
\section{write\_table -- write design as connectivity table}
\label{cmd:write_table}
\begin{lstlisting}[numbers=left,frame=single]
write_table [options] [filename]
Write the current design as connectivity table. The output is a tab-separated
ASCII table with the following columns:
module name
cell name
cell type
cell port
direction
signal
module inputs and outputs are output using cell type and port '-' and with
'pi' (primary input) or 'po' (primary output) or 'pio' as direction.
\end{lstlisting}
\section{write\_verilog -- write design to Verilog file}
\label{cmd:write_verilog}
\begin{lstlisting}[numbers=left,frame=single]
write_verilog [options] [filename]
Write the current design to a Verilog file.
-sv
with this option, SystemVerilog constructs like always_comb are used
-norename
without this option all internal object names (the ones with a dollar
instead of a backslash prefix) are changed to short names in the
format '_<number>_'.
-renameprefix <prefix>
insert this prefix in front of auto-generated instance names
-noattr
with this option no attributes are included in the output
-attr2comment
with this option attributes are included as comments in the output
-noexpr
without this option all internal cells are converted to Verilog
expressions.
-siminit
add initial statements with hierarchical refs to initialize FFs when
in -noexpr mode.
-nodec
32-bit constant values are by default dumped as decimal numbers,
not bit pattern. This option deactivates this feature and instead
will write out all constants in binary.
-decimal
dump 32-bit constants in decimal and without size and radix
-nohex
constant values that are compatible with hex output are usually
dumped as hex values. This option deactivates this feature and
instead will write out all constants in binary.
-nostr
Parameters and attributes that are specified as strings in the
original input will be output as strings by this back-end. This
deactivates this feature and instead will write string constants
as binary numbers.
-simple-lhs
Connection assignments with simple left hand side without concatenations.
-extmem
instead of initializing memories using assignments to individual
elements, use the '$readmemh' function to read initialization data
from a file. This data is written to a file named by appending
a sequential index to the Verilog filename and replacing the extension
with '.mem', e.g. 'write_verilog -extmem foo.v' writes 'foo-1.mem',
'foo-2.mem' and so on.
-defparam
use 'defparam' statements instead of the Verilog-2001 syntax for
cell parameters.
-blackboxes
usually modules with the 'blackbox' attribute are ignored. with
this option set only the modules with the 'blackbox' attribute
are written to the output file.
-selected
only write selected modules. modules must be selected entirely or
not at all.
-v
verbose output (print new names of all renamed wires and cells)
Note that RTLIL processes can't always be mapped directly to Verilog
always blocks. This frontend should only be used to export an RTLIL
netlist, i.e. after the "proc" pass has been used to convert all
processes to logic networks and registers. A warning is generated when
this command is called on a design with RTLIL processes.
\end{lstlisting}
\section{write\_xaiger -- write design to XAIGER file}
\label{cmd:write_xaiger}
\begin{lstlisting}[numbers=left,frame=single]
write_xaiger [options] [filename]
Write the top module (according to the (* top *) attribute or if only one module
is currently selected) to an XAIGER file. Any non $_NOT_, $_AND_, (optionally
$_DFF_N_, $_DFF_P_), or non (* abc9_box *) cells will be converted into psuedo-
inputs and pseudo-outputs. Whitebox contents will be taken from the equivalent
module in the '$abc9_holes' design, if it exists.
-ascii
write ASCII version of AIGER format
-map <filename>
write an extra file with port and box symbols
-dff
write $_DFF_[NP]_ cells
\end{lstlisting}
\section{xilinx\_dffopt -- Xilinx: optimize FF control signal usage}
\label{cmd:xilinx_dffopt}
\begin{lstlisting}[numbers=left,frame=single]
xilinx_dffopt [options] [selection]
Converts hardware clock enable and set/reset signals on FFs to emulation
using LUTs, if doing so would improve area. Operates on post-techmap Xilinx
cells (LUT*, FD*).
-lut4
Assume a LUT4-based device (instead of a LUT6-based device).
\end{lstlisting}
\section{xilinx\_dsp -- Xilinx: pack resources into DSPs}
\label{cmd:xilinx_dsp}
\begin{lstlisting}[numbers=left,frame=single]
xilinx_dsp [options] [selection]
Pack input registers (A2, A1, B2, B1, C, D, AD; with optional enable/reset),
pipeline registers (M; with optional enable/reset), output registers (P; with
optional enable/reset), pre-adder and/or post-adder into Xilinx DSP resources.
Multiply-accumulate operations using the post-adder with feedback on the 'C'
input will be folded into the DSP. In this scenario only, the 'C' input can be
used to override the current accumulation result with a new value, which will
be added to the multiplier result to form the next accumulation result.
Use of the dedicated 'PCOUT' -> 'PCIN' cascade path is detected for 'P' -> 'C'
connections (optionally, where 'P' is right-shifted by 17-bits and used as an
input to the post-adder -- a pattern common for summing partial products to
implement wide multipliers). Limited support also exists for similar cascading
for A and B using '[AB]COUT' -> '[AB]CIN'. Currently, cascade chains are limited
to a maximum length of 20 cells, corresponding to the smallest Xilinx 7 Series
device.
This pass is a no-op if the scratchpad variable 'xilinx_dsp.multonly' is set
to 1.
Experimental feature: addition/subtractions less than 12 or 24 bits with the
'(* use_dsp="simd" *)' attribute attached to the output wire or attached to
the add/subtract operator will cause those operations to be implemented using
the 'SIMD' feature of DSPs.
Experimental feature: the presence of a `$ge' cell attached to the registered
P output implementing the operation "(P >= <power-of-2>)" will be transformed
into using the DSP48E1's pattern detector feature for overflow detection.
-family {xcup|xcu|xc7|xc6v|xc5v|xc4v|xc6s|xc3sda}
select the family to target
default: xc7
\end{lstlisting}
\section{xilinx\_srl -- Xilinx shift register extraction}
\label{cmd:xilinx_srl}
\begin{lstlisting}[numbers=left,frame=single]
xilinx_srl [options] [selection]
This pass converts chains of built-in flops (bit-level: $_DFF_[NP]_, $_DFFE_*
and word-level: $dff, $dffe) as well as Xilinx flops (FDRE, FDRE_1) into a
$__XILINX_SHREG cell. Chains must be of the same cell type, clock, clock polarity,
enable, and enable polarity (where relevant).
Flops with resets cannot be mapped to Xilinx devices and will not be inferred.
-minlen N
min length of shift register (default = 3)
-fixed
infer fixed-length shift registers.
-variable
infer variable-length shift registers (i.e. fixed-length shifts where
each element also fans-out to a $shiftx cell).
\end{lstlisting}
\section{zinit -- add inverters so all FF are zero-initialized}
\label{cmd:zinit}
\begin{lstlisting}[numbers=left,frame=single]
zinit [options] [selection]
Add inverters as needed to make all FFs zero-initialized.
-all
also add zero initialization to uninitialized FFs
\end{lstlisting}
Reference in New Issue View Git Blame Copy Permalink